Understanding the interaction between microorganisms and fluid dynamics is important for aquatic ecosystems, though only sporadic attention has been focused on this topic in the past. In this study, particular attention was paid to the phenol-degrading bacterial strains Microbacterium oxydans LY1 and Alcaligenes faecalis LY2 subjected to controlled fluid flow under laboratory conditions. These two strains were found to be able to degrade phenols over a concentration range from 50 to 500 mg/L under different turbulence conditions ranging from 0 to 250 rpm. The time it took to reach total phenol degradation decreased when the turbulence was increased in both strains, with increasing energy dissipation rates ranging from 0.110 to 6.241 W/kg, corresponding to changes in the bacterial diffusive sublayer thickness (δ) and enhanced oxygen uptake. Moreover, the maximum specific growth rates of the two strains also increased with the enhancement of turbulence. A model integrating growth inhibition and fluid motion was proposed based on the self-inhibition Haldane model by introducing a turbulence parameter, α. The resulting modified Haldane model was designed to include fluid motion as a variable in the quantification of the physiological responses of microorganisms. This modified Haldane model could be considered a useful laboratory reference when modeling procedures for water environment bioremediation.
Cell nutrition uptake cartoon schematic diagram for M. oxydans LY1 under different turbulent condition (50 and 200 rpm).
Hg emission flux from various land covers, such as forests, wetlands, and urban areas, have been investigated. China has the largest area of coalfield in the world, but data of Hg flux of coalfields, especially, those with coal fires, are seriously limited. In this study, Hg fluxes of a coalfield were measured using the dynamic flux chamber (DFC) method, coupled with a Lumex multifunctional Hg analyzer RA-915+ (Lumex Ltd., Russia). The results show that the Hg flux in Wuda coalfield ranged from 4 to 318 ng m?2 h?1, and the average value for different areas varied, e.g., coal-fire area 99 and 177 ng m?2 h?1; no coal-fire area 19 and 32 ng m?2 h?1; and backfilling area 53 ng m?2 h?1. Hg continued to be emitted from an underground coal seam, even if there were no phenomena, such as vents, cracks, and smog, of coal fire on the soil surface. This phenomenon occurred in all area types, i.e., coal-fire area, no coal-fire area, and backfilling area, which is universal in Wuda coalfield. Considering that many coalfields in northern China are similar to Wuda coalfield, they may be large sources of atmospheric Hg. The correlations of Hg emission flux with influence factors, such as sunlight intensity, soil surface temperature, and atmospheric Hg content, were also investigated for Wuda coalfield.
?
The changes in some potentially toxic elements (PTEs) including lead (Pb), cadmium (Cd), arsenic (As), iron (Fe), zinc (Zn), and copper (Cu) during pekmez (grape molasses-like syrup) processing and the utilization of various types of clarifiers (white soil, bentonite, and gelatin) in two levels (1.5 and 3% w/w) were analyzed. The average concentrations of Pb, Cd, As, Fe, Zn, and Cu in grape samples were measured as 0.055?±?0.005, 0.030?±?0.002, 0.044?±?0.002, 2.882?±?0.013, 2.372?±?0.088, and 1.194?±?0.01 μg g?1. During pekmez production, the range of changes in Pb, Cd, As, Fe, Zn, and Cu was ?43.38% to 40.25%, ?55.49% to 0.23%, ?76.15% to 1.80%, ?74.15% to 58.47%, ?40.55% to ?18.12%, and ?83.16% to ?21.39%, respectively. The effect of the clarification process on the PTEs depended on the type and concentration of both PTE and clarifier agent used while the incorporation of gelatin resulted in a significant reduction in all of PT.
Graphical abstract
As an ubiquitous carcinogen, polycyclic aromatic hydrocarbons (PAHs) are closely related to anthropogenic activities. The process of urbanization leads to the spatial interlacing of farmlands and urbanized zones. However, field evidence on the influence of urbanization on the accumulation of PAHs in crops of peri-urban farmlands is lacking. This study comparatively investigated the urbanization-driven levels, compositions, and sources of PAHs in 120 paired plant and soil samples collected from the Yangtze River Delta in China and their species-specific human intake risks. The concentrations of PAHs in crops and soils in the peri-urban areas were 2407.92 ng g?1 and 546.64 ng g?1, respectively, which are significantly higher than those in the rural areas. The PAHs in the root were highly relevant to those in the soils (R2?=?0.63, p?<?0.01), and the root bioconcentration factors were higher than 1.0, implying the contributions of root uptake to plant accumulations. However, the translocation factors in the peri-urban areas (1.57?±?0.33) were higher than those in the rural areas (1.19?±?0.14), indicating the enhanced influence through gaseous absorption. For the congeners, the 2- to 3-ring PAHs showed a higher plant accumulation potential than the 4- to 6-ring PAHs. Principal component analysis show that the PAHs in the peri-urban plants predominantly resulted from urbanization parameters, such as coal combustion, vehicle emissions, and biomass burning. The mean values of estimated dietary intake of PAHs from the consumption of peri-urban and rural crops were 9116 ng day?1 and 6601.83 ng day?1, respectively. The intake risks of different crops followed the order rice?>?cabbage?>?carrot?>?pea. Given the significant input of PAHs from urban to farmland, the influence of many anthropogenic pollutants arising from rapid urbanization should be considered when assessing the agricultural food safety.
Graphical abstractArabidopsis thaliana was selected as model organisms to investigate the toxic effect and mechanism of four kinds of imidazolium and pyridinium ionic liquids (ILs) on plant seedling taproots. After exposure to ILs, the growth of seedling taproots was significantly inhibited in a dose-dependent manner. The toxicity of ILs on seedling taproots was [Bmim][BF4] > [Bmpy][BF4] > [Bmim][Br] > [Bmpy][Br]. The reduction of seedling root cell vitality, aggravation of seedling root cell death, and repression of gravitropic growth responses were observed. The amounts of H2O2 and ROS in seedlings were enhanced with increasing concentrations of ILs. Moreover, the expression levels of cdc2a and pcna1 genes were decreased after exposure to ILs. Our results suggest that ILs can induce the overproduction of ROS in A. thaliana seedling taproots and thus cause oxidative damage to seedling taproots. Meanwhile, ILs alter the expression patterns of two cell cycle-related genes and hence cause the seedling taproot growth inhibition. This work provides an integrated understanding of the toxic effect and mechanism of ILs on A. thaliana seedlings at the molecular and physiological level and also provides theoretical basis and reference for the environmental safety evaluation of ILs, prior to their widespread use and release.
?
When sewage sludge is incorrectly applied, it may adversely impact agro-system productivity. Thus, this study addresses the reaction of Cucumis sativus L. (cucumber) to different amendment rates (0, 10, 20, 30, 40 and 50 g kg?1) of sewage sludge in a greenhouse pot experiment, in which the plant growth, heavy metal uptake and biomass were evaluated. A randomized complete block design with six treatments and six replications was used as the experimental design. The soil electrical conductivity, organic matter and Cr, Fe, Zn and Ni concentrations increased, but the soil pH decreased in response to the sewage sludge applications. As approved by the Council of European Communities, all of the heavy metal concentrations in the sewage sludge were less than the permitted limit for applying sewage sludge to land. Generally, applications of sewage sludge of up to 40 g kg?1 resulted in a considerable increase in all of the morphometric parameters and biomass of cucumbers in contrast to plants grown on the control soil. Nevertheless, the cucumber shoot height; root length; number of leaves, internodes and fruits; leaf area; absolute growth rate and biomass decreased in response to 50 g kg?1 of sewage sludge. All of the heavy metal concentrations (except the Cu, Zn and Ni in the roots, Mn in the fruits and Pb in the stems) in different cucumber tissues increased with increasing sewage sludge application rates. However, all of the heavy metal concentrations (except the Cr and Fe in the roots, Fe in the leaves and Cu in the fruits) were within the normal range and did not reach phytotoxic levels. A characteristic of these cucumbers was that all of the heavy metals had a bioaccumulation factor <1.0. All of the heavy metals (except Cd, Cu and Zn) had translocation factors that were <1.0. As a result, the sewage sludge used in this study could be considered for use as a fertilizer in cucumber production systems in Saudi Arabia and can also serve as a substitute method of sewage sludge disposal.
The effects of different sewage sludge amendment rates on the heavy metal bioaccumulation, growth and biomass of cucumbers
Clogging is the most significant challenge limiting the application of constructed wetlands. Application of a forced resting period is a practical way to relieve clogging, particularly bioclogging. To reveal the alleviation mechanisms behind such a resting operation, evapotranspiration and oxygen flux were studied during a resting period in a laboratory vertical-flow constructed wetland model through physical simulation and numerical model analysis. In addition, the optimum theoretical resting duration was determined based on the time required for oxygen to completely fill the pores, i.e., formation of a sufficiently thick and completely dry layer. The results indicated that (1) evapotranspiration was not the key factor, but was a driving force in the alleviation of bioclogging; (2) the rate of oxygen diffusion into the pores was sufficient to oxidize and disperse the flocculant biofilm, which was essential to alleviate bioclogging. This study provides important insights into understanding how clogging/bioclogging can be alleviated in vertical-flow constructed wetlands.
Evapotranspiration versus oxygen intrusion in alleviating bioclogging in vertical flow constructed wetlands
Acetaminophen (ACT) is one of the most frequently detected pharmaceuticals in aqueous environments, and treatment of ACT were generally carried out by photocatalytic degradations under high energy UV irradiation. In this study, potassium ferricyanide was utilized as a quadruple-elemental dopant in a TiO2 photocatalyst in order to enhance its visible-light activity. Two critical parameters (amounts of dopants and durations of calcination) of the synthesis of the photocatalyst by a sol–gel method were systematically evaluated. Crystal structure of the doping TiO2 was examined by X-ray diffraction while the effects of the two parameters on the photocatalytic activity were elucidated by various characterizations. Increasing the amount of dopant or the duration of calcination red-shifted the UV–vis DRS of the doped TiO2. The estimated band gap energy of the doped TiO2 decreased slightly as the amount of dopant increased, but it increased as the duration of calcination increased. The FT-IR yielded characteristic peaks that revealed the effects of the two parameters, whereas the SEM images revealed the morphological evolutions of each effect. The photocatalyst, synthesized at optimum conditions was able to remove 99.1 % acetaminophen with rate constant of 7.9 × 10−3 min−1, which was 4.88 times greater than virgin TiO2. In general, this study not only optimized synthetic conditions of the new visible-light active photocatalyst for ACT degradation but also presented characterizations conducted by SEM, XRD, UV–vis DRS, and FTIR to elucidate the relationship between modified structure and the photocatalytic activity.
Effects of doping amounts of K3[Fe(CN)6] and calcunation duration on visible light absorbance of TiO2 photocatalysts
This work reports the use of a cross-linked ureasil–PEO hybrid matrix (designated PEO800) as an efficient adsorbent to retain the emerging contaminant bisphenol A (BPA) from an aqueous medium. The in-deep experimental and theoretical results provide information about the interactions between PEO800 and BPA. The in situ UV-vis spectroscopy data and the pseudo-first order, pseudo-second order, Elovich, and Morris–Webber intraparticle diffusion models allowed us to propose a three-step mechanism for the adsorption of BPA onto PEO800. The results indicate that the pseudo-first-order kinetic model effectively describes the adsorption of BPA onto PEO800. Differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy confirmed the interaction of PEO800 with BPA, showing an alteration in the chemical environment of the polymer ether oxygen atoms present in the hybrid matrix. The molecular dynamic simulation provides further evidence that the BPA molecules interact preferentially with PEO. The amount of desorbed BPA depended on the pH and solvent used in the assays. This work provides new opportunities for using the hydrophilic ureasil–PEO matrix which has demonstrated its abilities in being a fast and easy alternative to successfully removing organic contaminants from aqueous mediums and therefore having potential applications in water remediation.
Graphical abstract
The depletion of fossil fuels and hike in crude oil prices were some of the main reasons to explore new alternatives from renewable source of energy. This work presents the impact of various bowl geometries on diesel engine with diesel and biodiesel samples. Three non-edible oils were selected, namely pumpkin seed oil, orange oil and neem oil. These oils were converted into respective biodiesel using transesterification process in the presence of catalyst and alcohol. After transesterification process, the oils were termed as pumpkin seed oil methyl ester (PSOME), orange oil methyl ester (OME) and neem oil methyl ester (NOME), respectively. The engine used for experimentation was a single-cylinder four-stroke water-cooled direct-injection diesel engine and loads were applied to the engine using eddy current dynamometer. Two bowl geometries were developed, namely toroidal combustion chamber (TCC) and trapezoidal combustion chamber (TRCC). Also, the engine was inbuilt with hemispherical combustion chamber (HCC). The base line readings were recorded using neat diesel fuel with HCC for various loads. Followed by 20% of biodiesel mixed with 80% neat diesel for all prepared methyl esters and termed as B1 (20% PSOME with 80% diesel), B2 (20% OME with 80% diesel) and B3 (20% NOME with 80% diesel). All fuel samples were tested in HCC, TCC and TRCC bowl geometries under standard injection timing and with compression ratio of 18. Increased brake thermal efficiency and reduced brake specific fuel consumption were observed with diesel in TCC geometry. Also, higher heat release and cylinder pressures with lower ignition delay were recorded with TCC bowl geometry. TCC bowl geometry showed lower CO, HC and smoke emissions with B2 fuel sample than diesel and other biodiesel samples. But, higher NOx emission was observed in HCC and TCC than that in TRCC bowl geometry.
?
Date palm waste–derived biochar (DBC) was produced through pyrolysis (600 °C) and modified with zeolite (Z-DBC), silica (S-DBC), or nano-zerovalent iron (nZVI-DBC) to design efficient sorbents. The pristine and engineered biochars were characterized by SEM, XRD, BET, TGA, CHNS-O, and FTIR to investigate the surface, structural, and mineralogical composition. The nZVI-DBC exhibited lowest pH (6.15) and highest surface area (220.92 m2 g−1), carbon (80.55%), nitrogen (3.78%), and hydrogen (11.09%) contents compared with other biochars. Isotherm sorption data for chlortetracycline (CTC) removal from aqueous solutions was described well by Langmuir and Redlich–Peterson isotherms showing the highest fitness (R2 values in the range of 0.88–0.98 and 0.88–0.99, respectively). Langmuir predicted maximum CTC adsorption capacity was in order of nZVI-DBC (89.05 mg g−1) > S-DBC (45.57 mg g−1) > Z-DBC (30.42 mg g−1) > DBC (28.19 mg g−1). Kinetics adsorption data was best described by power function model (R2 = 0.93–0.99), followed by interaparticle diffusion (R2 = 0.85–0.96) model. The nZVI-DBC performed outclass by removing 98% of CTC, followed by S-DBC (68%), Z-DBC (35%), and DBC (36%). Chemisorption, H-bonding, and interaparticle diffusion were the operating mechanisms for CTC adsorption onto DBC, S-DBC, and Z-DBC, while π-π electron donor–accepter interactions and redox reactions augmented these mechanisms for highest CTC adsorption onto nZVI-DBC. Therefore, nZVI-DBC may serve as an efficient green technology for the removal of CTC from aqueous solutions and to reduce surface date palm waste pollution.
.
This study investigates the spatiotemporal variability of major and trace elements, dissolved organic carbon (DOC), total dissolved solids (TDS), and suspended particulate matter (SPM) in surface waters of several hydrosystems of the Loire River watershed in France. In particular, this study aims to delineate the impact of the abovementioned water physicochemical parameters on natural iron and manganese physical speciation (homoaggregation/heteroaggregation) among fine colloidal and dissolved (<?10 nm), colloidal (10–450 nm) and particulate (>?450 nm) phases in Loire River watershed. Results show that the chemistry of the Loire River watershed is controlled by two end members: magmatic and metamorphic petrographic context on the upper part of the watershed; and sedimentary rocks for the middle and low part of the Loire. The percentage of particulate Fe and Mn increased downstream concurrent with the increase in SPM and major cations concentration, whereas the percentage of colloidal Fe and Mn decreased downstream. Transmission electron microscopy analyses of the colloidal and particulate fractions (from the non-filtered water sample) revealed that heteroaggregation of Fe and Mn rich natural nanoparticles and natural organic matter to the particulate phase is the dominant mechanism. The heteroaggregation controls the partitioning of Fe and Mn in the different fractions, potentially due to the increase in the ionic strength, and divalent cations concentration downstream, and SPM concentration. These findings imply that SPM concentration plays an important role in controlling the fate and behavior of Fe and Mn in various sized fractions.
Physical speciation by heteroaggregation of (Fe-Mn) compounds: high [SPM]?→?[Fe-Mn] particulate faction; low {SPM]?→?[Fe-Mn] colloid-dissolved fraction.
Ecological assessment of freshwater ecosystems based on diatom metrics is an important issue for attaining environmental sustainability. The present study aimed to evaluate differences in the diatom–stressor relationship in relatively least disturbed streams in the Konya closed river basin using multivariate analyses and to bio-assess streams by the application of different ecoregional diatom indices. Cocconeis euglypta, Cymbella excisa, Cocconeis placentula, and Achnanthidium minutissimum are the most contributing species to the dissimilarity of sampling stations between rainy (spring) and dry (summer and fall) seasons and also between altitude (A2 800- < 1600 m and A3 ≥ 1600 m) groups. The first two axes of canonical correspondence analysis revealed a significant (82.8%) relationship between diatom species and stressors. Diatom species displayed distinct responses to environmental variables (electrical conductivity, Ni, Cu, B, and altitude) playing important roles on the distribution of species. Diatom indices indicate different ecological statuses of stations, from bad to high. European diatom indices except Duero Diatom Index (DDI) and Trophic Diatom Index (TDI) showed good responses to the eco-assessment of streams and indicated high ecological status for the least disturbed sampling stations symbolized as S16, S20, S24, S25, S27-29, S37, and S39. These results were also supported by abiotic evaluation. Although TIT was more competitive in the bio-assessment of streams among diatom indices, it is necessary to increase its species list by determining their trophic weights in future studies. Therefore, the use of ecoregion-specific diatom indices is suggested along with increasing the number of used species to correctly interpret the water quality.
Graphical AbstractMarine algae have made a strong contribution to global food security in the future. This study is the first report describing the concentration, pathways, and interactions of halogens in 15 species of marine algae collected from the Eastern Harbor in Alexandria, Egypt, relative to 22 key variables. The relationship between halogen content and chemical and biochemical parameters was studied through multivariate analysis. Among all the tested algae, the iodine content was the lowest (2.53–3.00 μg/g). The range of fluoride and chloride in macroalgae (1.12–1.70 and 0.10–0.46 mg/g) was smaller than that of microalgae (0.10–0.46 and 1.48–3.17 mg/g). The bromide content in macroalgae (0.36–5.45 mg/g) was higher than that in microalgae (0.40–0.76 mg/g). The halogen content in macroalgae was arranged in the order of Br > F > Cl > I. In addition, the biochemical parameters such as carbohydrates, proteins, lipids, and certain heavy metals (Fe, Zn, Cu, Mn, Pb, Ni, Co, Cd, and Cr) were determined. Calories, energy, total antioxidant activity (TAC), K/Na, and ion quotient amounts were estimated. The results showed that the green seaweed species had the highest TAC content. In most of the studied algal species, the calculated ion quotient referred to their likelihood of overcoming high blood pressure. The estimated daily intake (EDI) of algae showed no adverse effects on human health. Most of the research variables are below the acceptable WHO/FAO level. Generally, the calorie content of the selected algae is less than 2 kcal, which makes the algae considered an alternative source of healthy food to reduce obesity.
Graphical abstract
Dissolved humic substances (DHSs) are the major components of organic matter in the aquatic environment. DHSs are well known to considerably affect the speciation, solubility, and toxicity of a wide variety of pollutants in the aquatic environment. In this study, the effects of the toxicity of heavy metals and hydrophobic organic pollutants (HOPs) on Chlamydomonas reinhardtii in the presence of humic acid (HA) were examined by a microscale algal growth inhibition (μ-AGI) test based on spectrophotometric detection. To clarify the relationship between the chemical properties of HAs and the toxicity change of pollutants, eight HAs from different sources were prepared and used. HAs were responsible for mitigating the toxicity of Hg, Cu, pesticides (γ-HCH, 2,4-D, and DDT), and polycyclic aromatic hydrocarbons (PAHs) such as naphthalene (Nap), anthracene (Ant), and benzo[a]pyrene (BaP). In particular, an approximately 100-fold decrease in the toxicity of BaP was observed in the presence of 10 ppm HAs extracted from tropical peat. The results indicated that the carboxylic group content and the HA molecular weight are correlated to the changes in the heavy metal toxicity. For HOPs, the aromaticity and polarity of HAs are crucial for mitigating their toxicity. Furthermore, it was clearly shown that the lake water including a high concentration of DHSs collected from Central Kalimantan, Indonesia, reduced the toxicity of Hg and γ-HCH on Chlamydomonas reinhardtii.
Graphical abstract
This study assessed the concentration, bioconcentration, and bioaccumulation of As, Cd, Co, Cr, Cu, Mg, Mn, Ni, Pb, and Zn in juvenile fishes (Acestrorynchus pantaneiro, Brycon orbygnianus, Cyphocharax voga, Megaleporinus obtusidens, Odontesthes bonariensis, Pimelodus maculatus, Prochilodus lineatus, Salminus brasiliensis, and Schizodon borelli) in the Lower Paraná River (Argentina), the most extensive floodplain from the Plata Basin. The floodplain is crucial for the reproduction and growth of various species such as P. lineatus, M. obtusidens, and S. brasiliensis, which complete their life cycle in this environment. In total, 90 individuals were sampled for nitrogen stable isotope, and trace element analysis in muscle tissue, water, and sediment was analyzed. The results show that all the studied species bioaccumulate Cr, Mg, Ni, and Zn. In particular, B. orbygnianus and P. maculatus presented the highest bioaccumulation factor for Cr. A biodilution of Co through the food chain was observed. No positive correlation was found between element concentration and trophic level, but we observed significant differences between trophic guilds (herbivorous, omnivorous, and carnivorous). Our findings suggest that feeding habits determine trace element concentrations. To establish differential behavior between different species within the aquatic web further studies are necessary, particularly in the floodplain of the Paraná, which is a crucial nursery area for most commercially important fishes from the Plata Basin.
Graphical abstract
Echinacea purpurea (L.) Moench was selected as a remediation plant in this study, and different concentrations of graphene oxide (GO) were added to Cd-contaminated soil. Through pot experiments, the effect of E. purpurea on Cd-contaminated soil was determined at 60 days, 120 days, and 150 days. A preliminary study on the remediation mechanism of GO was explored through changes in the forms of Cd in the rhizosphere soil, soil pH, and soil functional groups. Results showed that the optimal concentration of GO was 0.4 g/kg, and under the condition, the accumulation of Cd in the roots of E. purpurea was as high as 113.69 ± 23.86 mg/kg, and the maximum EF reached 5.87 ± 1.34. Compared with those of the control group, accumulated Cd concentration and EF in the roots increased by 60.34% and 2.32, respectively. Correlation analysis showed that the absorption and accumulation of Cd was negatively correlated with the exchangeable Cd content at 120 days, and the exchangeable Cd was negatively correlated with the relative content of functional groups in the soil with 0.4 g/kg GO (E2). The artificial application of GO to the soil can be used as an effective way to improve the effect of E. purpurea in the remediation of Cd soil pollution, and it has great application potential in the stabilization of plants and vegetations and restoration of high-concentration Cd-contaminated soil.
Graphical abstractTrimethylamine (TMA) is an odorous volatile organic compound emitted by industries. Algal-based biotechnologies have been proven as a feasible alternative for wastewater treatment, although their application to abate polluted air emissions is still scarce. This work comparatively assessed the removal of TMA in a conventional bacterial bubble column bioreactor (BC) and a novel algal-bacterial bubble column photobioreactor (PBC). The PBC exhibited a superior TMA abatement performance compared to the conventional BC. In this sense, the BC reached a removal efficiency (RE) and an elimination capacity (EC) of 78% and 12.1 g TMA m?3 h?1, respectively, while the PBC achieved a RE of 97% and a EC of 16.0 g TMA m?3·h?1 at an empty bed residence time (EBRT) of 2 min and a TMA concentration ~500 mg m?3. The outstanding performance of the PBC allowed to reduce the operating EBRT to 1.5 and 1 min while maintaining high REs of 98 and 94% and ECs of 21.2 and 28.1 g m?3·h?1, respectively. Moreover, the PBC improved the quality of the gas and liquid effluents discharged, showing a net CO2 consumption and decreasing by ~ 30% the total nitrogen concentration in the liquid effluent via biomass assimilation. A high specialization of the bacterial community was observed in the PBC, Mumia and Aquamicrobium sp. being the most abundant genus within the main phyla identified.
GraphicalAbstract
A review of the applicability of electron beam water radiolysis for sewage sludge treatment is presented. Electron beam treatment has been proven to be a successful approach to the disinfection of both wastewater and sewage sludge. Nevertheless, before 2000, there were concerns about the perceived high capital costs of the accelerator and with public acceptance of the usage of radiation for water treatment purposes. Nowadays, with increased knowledge and technological development, it may be not only possible but also desirable to use electron beam technology for risk-free sewage sludge treatment, disposal and bio-friendly fertiliser production. Despite the developing interest in this method, there has been no attempt to perform a review of the pertinent literature relating to this technology. It appears that understanding of the mechanism and primary parameters of disinfection is key to optimising the process. This paper aims to reliably characterise the sewage sludge electron beam treatment process to elucidate its major issues and make recommendations for further development and research.
Graphical abstract