杂多酸水溶液脱除烟气中SO2的性能研究

合成了H3PMo12O40、H4SiW12O40、H3PW12O40、H4PMo11VO40、H5PMo10V2O40和H6PMo9V3O406种杂多酸,分别采用红外光谱（FT-IR）和X射线衍射（XRD）表征杂多酸的结构,并采用气相色谱仪对6种杂多酸水溶液进行脱硫实验测试。实验结果表明：制备的6种杂多酸具有良好的Keggin型结构;H3PMo12O40、H3PW12O40和H4SiW12O40的3种水溶液中,磷钼杂多酸的脱硫性能最好,脱硫率在120 min时可达到16.38%;不同比例的多原子也会使杂多酸有不同的脱硫性能,脱硫性能顺序为：H6PMo9V3O40〉H5PMo10V2O40〉H4PMo11VO40;且6种杂多酸的脱硫稳定性的顺序为：H4PMo11VO40〉H6PMo9V3O40〉H3PMo12O40〉H5PMo10V2O40〉H4SiW12O40≈H3PW12O40。     

Efficient use of Fe metal as an electron transfer agent in a heterogeneous Fenton system based on Fe0/Fe3O4 composites

In this work a novel heterogeneous Fenton system based on Fe(0)/Fe3O4 composites is described. The composites with several Fe(0)/Fe3O4 ratios were prepared by two different methods, i.e. mechanical alloying of Fe(0) and Fe3O4 powders and controlled reduction of Fe3O4 with H2. Reaction studies and detailed Conversion Electron M?ssbauer surface characterization of the composites Fe(0)/Fe3O4, Fe(0), Fe3O4, alpha-Fe2O3 and gamma-Fe2O3 suggested that Fe2+surf species are essential to produce an active Fenton system. Kinetic studies for the oxidation of the dye methylene blue, used as an organic model molecule, and for the peroxide decomposition suggest that the reactions proceed via HO* radicals generated from Fe2+surf species and H2O2 in a Fenton like mechanism. The increase in activity caused by the addition of Fe(0) is discussed in terms of a creation of Fe2+surf species during the preparation of the composite and by an electron transfer mechanism from Fe(0) to Fe3+surf during the Fenton reaction to regenerate the Fe2+surf active species.     

Fe3O4纳米磁性微粒对全氟辛烷磺酸盐的吸附

采用共沉淀法合成Fe3O4纳米磁性颗粒,用透射电子显微镜(TEM)、X射线衍射仪(XRD)以及振动样品磁强计(VSM)对Fe3O4纳米磁性颗粒的粒径、形貌和磁性进行表征并研究Fe3O4纳米磁性微粒对全氟辛磺酸盐的吸附。结果表明:在PFOS初始浓度4 mg/L,pH为3,反应时间24 h,Fe3O4纳米磁性微粒投加量1.25 g/L,对全氟辛磺酸盐去除率达到90%。Fe3O4纳米磁性微粒对PFOS的吸附符合Freundlich吸附方程。     

淀粉改性纳米四氧化三铁的制备及其除磷效能的研究

以可溶性淀粉为改性剂,采用氧化沉淀法分别制备了可溶性淀粉改性Fe3O4以及纯Fe3O4,并研究了2种Fe3 O4粒径、表面性质以及除磷效能的差异。实验结果表明,淀粉改性使得纳米Fe3 O4粒径减小,粒径由60 nm减小到10nm左右;红外和Zeta电位结果表明淀粉在Fe3 O4粒子表面是化学吸附;2种纳米Fe3 O4对...     

Fe3O4纳米磁性微粒对全氟辛烷磺酸盐的吸附

采用共沉淀法合成Fe3O4纳米磁性颗粒,用透射电子显微镜（TEM）、X射线衍射仪（XRD）以及振动样品磁强计（VSM）对Fe3O4纳米磁性颗粒的粒径、形貌和磁性进行表征并研究Fe3O4纳米磁性微粒对全氟辛磺酸盐的吸附。结果表明：在PFOS初始浓度4 mg/L,pH为3,反应时间24 h,Fe3O4纳米磁性微粒投加量1.25 g/L,对全氟辛磺酸盐去除率达到90%。Fe3O4纳米磁性微粒对PFOS的吸附符合Freundlich吸附方程。     

The promoter effect and a rate expression of the catalytic incineration of (CH3)2S2 over an improved CuO-MoO3/gamma-Al2O3 catalyst

The CuO-MoO3/gamma-Al2O3 catalyst, confirmed previously as having good activity in the catalytic incineration of (CH3)2S2, was employed as the principal catalyst in this study. With the aim of improving catalyst activity and resistance to deactivation by sulfur compounds, a promoter was added either before adding the precursors of Cu and Mo or together with Cu and Mo onto the gamma-Al2O3. Promoters included transition metals and elements from groups IA-VIIA in the chemical periodic table. Experimental results reveal Cr2O3 as the most effective promoter, with an optimal composition of 5 wt.% Cu, 6 wt.% Mo and 4 wt.% Cr (designated as Cu(5)-Mo(6)-Cr(4)/gamma-Al2O3). Knowing that higher acidity can improve activity, we further investigated the effect of acid treatment on the performance of the Cu(5)-Mo(6)-Cr(4)/gamma-Al2O3 catalyst. Experimental results indicate the H2SO4-treated catalyst (Cu(5)-Mo(6)-Cr(4)/sulfated-gamma-Al2O3) has a better activity and durability. A study for finding an appropriate rate expression for the catalytic incineration of (CH3)2S2 by Cu(5)-Mo(6)-Cr(4)/sulfated-gamma-Al2O3 was carried out in a differential reactor. The results show that the Mars-Van Krevelen model is applicable to this destructive oxidation reaction. Results additionally reveal that competitive adsorption of CH4 reduces conversion of (CH3)2S2.     

Oxidant air pollution effects on plants of Joshua Tree National Monument

Joshua Tree National Monument (JOTR) is located about 100 km east of the Los Angeles Basin, site of the heaviest concentration of photochemical oxidant (O(3)) air pollution in the US. This investigation was conducted to measure O(3) concentrations in JOTR and to determine the effects of O(3) on vegetation in the park. Potentially phytotoxic concentrations of O(3) were recorded in JOTR in 1984 and 1985, but peak concentration occurred at night, when most plant species would be less sensitive to O(3). No O(3) effects were observed on permanent vegetation observation plots in JOTR in 1984 or 1985. Controlled exposures of native summer annual and woody perennial species to O(3) showed that most did not develop visible O(3) injury symptoms except at concentrations higher than those expected in the park. However, Rhus trilobata Nutt. was injured at 0.10 ppm O(3), 4 h per day for 4 days. This species would be a useful bioindicator to assess the effects of O(3) on native desert plants.     

Constructing 3D magnetic flower-like Fe3O4@SiO2@Co3O4@BiOCl heterojunction photocatalyst for degrading rhodamine B

Environmental Science and Pollution Research - In this work, the 3D magnetic flower-like Fe3O4@SiO2@Co3O4@BiOCl heterojunction photocatalyst was successfully prepared. The combination of BiOCl with...     

MnOx／Al-SBA-15催化剂低温NH3选择性催化还原NO的原位红外研究

用原位红外分别进行了MnOx／Al-SBA-15催化剂上NH3和NO＋O2的吸附态和瞬态实验以及NH3＋NO＋02反应的稳态实验。结果表明,催化剂上存在着L酸位和B酸位,NH3吸附在催化剂上形成配位态的NH3和NH4＋,配位态的NH3能脱氢形成-NH2活性中间态。NO＋O2在催化剂上吸附形成硝酸盐类、硝基类和亚硝酸盐类。将NO＋O2通入预吸附NH3的催化剂中时,表面的配位态的NH3、NH4＋和-NH2都会减少直至消失,SCR反应显著。而将NH3通人预吸附NO＋O2的催化剂中时,只有硝基类和亚硝酸盐类减少,硝酸盐类基本不发生变化,SCR反应微弱。NH3＋NO＋O2稳态反应中,催化剂表面稳定存在着NH4＋和硝酸盐类,SCR反应显著。     

Mechanisms of NOx removal from flue gas by zero valent iron

Chemical reaction between nitric oxide (NO) andzero valent iron (ZVI) was studied in a packed-bed column process with high temperatures based on ZVI strong reducing abilities. For six controlled temperatures of 523-773 K and 400 ppm of NO (typical flue gas temperature and concentration), under short empty bed contacttime ([EBCT] 0.0226-0.0679 sec), NO was completely removed for temperature of 573-773 K but not for 523 K. Break-through curves were conducted for the five working temperatures, and the results indicated that NO reductions by ZVI were varied from 2 to 26.7 mg NO/g ZVI. Higher temperature and longer EBCT achieved better NO removal efficiency. X-ray diffraction (XRD) and electron spectroscopy for chemical analysis (ESCA) were conducted to analyze the crystal structure and oxidation state of the reacted ZVI. Three layers of iron species were detected by XRD: ZVI, Fe3O4, and Fe2O3. ZVI was the most prevalent species, and Fe3O4 and Fe2O3 were less from the XRD analysis. By ESCA, the oxidation state on the reacted ZVI surface was determined, and the species was identifled as Fe2O3, which is the most oxidizing species for iron. Therefore, three layers from the ZVI core to the ZVI surface can be identified: ZVI, Fe3O4, and Fe2O3. Combining the results from XRD and ESCA, the mechanisms for ZVI and NO can be proposed as two consecutive reactions from lower oxidation state (ZVI) in the core to higher oxidation state on the iron surface (Fe2O3): 3Fe + 4NO<--(high temperature)-->Fe3O4 + 2N2 (A1), 4Fe3O4 + 2NO<--(high temperature)-->6Fe2O3 + N2* (A2) Because there was only <5% ZVI used to remove NO comparing to theoretical ZVI used based on the proposed stoichiometry, it can be concluded that the heterogeneous reaction only occurred on the ZVI surface instead of on bulk of the ZVI.     

Fe2O3-Cr2O3/TiO2系列催化剂的结构和脱硝性能

研究以纳米TiO2为载体,浸渍负载过渡金属氧化物,以CO为还原剂的脱硝催化剂的脱硝性能。实验中以计算量的Ni（NO3）2和Fe（NO3）3混合溶液浸渍纳米TiO2粉末,室温下搅拌30 min至混合均匀,放入旋转蒸发器中,70℃下至水分蒸干为止;所得粉末在550℃下、空气气氛中焙烧4 h即得所需催化剂。用以上方法分别制备2%Fe2O3-10%Cr2O3/TiO2、4%Fe2O3-8%Cr2O3/TiO2、6%Fe2O3-6%Cr2O3/TiO2、8%Fe2O3-4%Cr2O3/TiO2与10%Fe2O3-2%Cr2O3/TiO2等5种催化剂样品。实验结果表明,制备的催化剂具有较好的结构,分散较为均匀。对于CO＋NO反应,Fe2O3-Cr2O3/TiO2系列催化剂具有较好的催化活性,NO的转化率都达到了100%。其中,10%Fe2O3-2%Cr2O3/TiO2样品具有最好的低温活性,H2-TPR结果表明,这是由于10%Fe2O3-2%Cr2O3/TiO2催化剂更易于被CO预还原。     

Fluxes of N2O, CH4 and CO2 in a meadow ecosystem exposed to elevated ozone and carbon dioxide for three years

Open-top chambers (OTCs) were used to evaluate the effects of moderately elevated O3 (40-50 ppb) and CO2 (+100 ppm) and their combination on N2O, CH4 and CO2 fluxes from ground-planted meadow mesocosms. Bimonthly measurements in 2002-2004 showed that the daily fluxes of N2O, CH4 and CO2 reacted mainly to elevated O3, while the fluxes of CO2 also responded to elevated CO2. However, the fluxes did not show any marked response when elevated O3 and CO2 were combined. N2O and CO2 emissions were best explained by soil water content and air and soil temperatures, and they were not clearly associated with potential nitrification and denitrification. Our results suggest that the increasing O3 and/or CO2 concentrations may affect the N2O, CH4 and CO2 fluxes from the soil, but longer study periods are needed to verify the actual consequences of climate change for greenhouse gas emissions.     

Magnetic nanoparticles coated with aminated polymer brush as a novel material for effective removal of Pb(II) ions from aqueous environments

Environmental Science and Pollution Research - In the present study, a poly (vinylbenzyl chloride) grafted Fe3O4 nanoparticle (Fe3O4@PVBC) was prepared by surface-initiated reversible addition...     

制备条件对不同玻璃材料负载TiO_2活性影响研究

以光催化降解苯酚为探针反应,通过正交实验,系统研究了胶液配比、涂覆次数和焙烧温度等条件对以溶胶-凝胶法分别在普通钠钙玻璃和磨砂玻璃上制备TiO2光催化性能的影响,并利用环境扫描电镜（ESEM）对TiO2催化膜形貌进行了分析。研究表明,在普通钠钙玻璃片上负载TiO2催化膜的影响因素主次顺序为：硝酸体积〉涂覆次数〉焙烧温度〉V乙醇∶V酞酸丁酯,在选定实验条件下的最优条件为：涂覆次数为4次;焙烧温度=450℃;V乙醇∶V酞酸丁酯∶V硝酸（1∶4）：V水=400∶40∶1∶4。在磨砂玻璃片上负载TiO2催化膜的的影响因素主次顺序为：涂覆次数〉硝酸体积〉焙烧温度〉V乙醇：V酞酸丁酯,在选定实验条件下的最优条件为：涂覆次数为4次;焙烧温度=500℃;V乙醇∶V酞酸丁酯∶V硝酸（1∶4）∶V水=400∶40∶2∶4。通过扫描电镜可以观察到在普通钠钙玻璃片和磨砂玻璃片表面均附着一层白色的TiO2薄膜,颗粒粒径在100 nm左右。磨砂玻璃比普通钠钙玻璃负载更多的催化剂,磨砂玻璃基TiO2活性更高。磨砂玻璃是一种非常有前景的TiO2催化剂载体材料。     

Effects of fulvic acid on aggregation,sedimentation, and adsorption of Fe3O4 magnetic nanoparticles

Environmental Science and Pollution Research - Environmental behavior, bioavailability, and risks posed by Fe3O4, magnetic nanoparticles (Fe3O4 NPs) in surface waters are affected by complex...     

Photo–degradable and recyclable starch/Fe3O4/TiO2 nanocomposites: feasibility of an approach to reduce the recycling labor cost in plastic waste management

Environmental Science and Pollution Research - In this research, a biodegradable starch/Fe3O4/TiO2 bio-nanocomposites (SFT) were produced using different nano Fe3O4/TiO2 (FT) (3, 5, and 10 (wt% dry...     

Comparison of various advanced oxidation processes and chemical treatment methods for COD and color removal from a polyester and acetate fiber dyeing effluent

In this paper, a comparison of various advanced oxidation processes (O3, O3/UV, H2O2/UV, O3/H2O2/UV, Fe2+/H2O2) and chemical treatment methods using Al2(SO4)3.18H2O, FeCl3 and FeSO4 for the chemical oxygen demand (COD) and color removal from a polyester and acetate fiber dyeing effluent is undertaken. Advanced oxidation processes (AOPs) showed a superior performance compared to conventional chemical treatment, which maximum achievable color and COD removal for the textile effluent used in this study was 50% and 60%, respectively. Although O3/H2O2/UV combination among other AOPs methods studied in this paper was found to give the best result (99% removal for COD and 96% removal for color), use of Fe2+/H2O2 seems to show a satisfactory COD and color removal performance and to be economically more viable choice for the acetate and polyester fiber dyeing effluent on the basis of 90% removal.     

Fabrication and characterization of 3,4-diaminobenzophenone-functionalized magnetic nanoadsorbent with enhanced VOC adsorption and desorption capacity

Environmental Science and Pollution Research - The present study, for the first time, utilized 3,4-diaminobenzophenone (DABP)-functionalized Fe3O4/AC@SiO2 (Fe3O4/AC@SiO2@DABP) magnetic...     

Selective removal of anionic dyes in single and binary system using Zirconium and iminodiacetic acid modified magnetic peanut husk

Environmental Science and Pollution Research - A novel adsorbent (PN-Fe3O4-IDA-Zr) was developed from the chemical modification of peanut husk (a low cost material) with Fe3O4, iminodiacetic acid...     

Potential application of highly reactive Fe(0)/Fe3O4 composites for the reduction of Cr(VI) environmental contaminants

We describe the use of highly reactive Fe(0)/Fe3O4 composites for the reduction of Cr(VI) species in aqueous medium. The composites were prepared by simple mechanical alloying of metallic iron and magnetite in different proportions, i.e. Fe(0) 25, 50, 75 and 90wt%. While after 3h of reaction pure Fe(0) and pure Fe3O4 showed only a low reduction efficiency of 15% and 25% Cr(VI) conversion, respectively, the composites, in particular Fe(0)(25wt%)/Fe3O4, showed a remarkable activity with ca. 65% Cr(VI) conversion. Kinetic experiments showed a high reaction rate during the first 3h, which subsequently decreased strongly, probably due to a pH increase from 6 to 8. Experiments with composites based on Fe(0)/alpha-Fe2O3, Fe(0)/gamma-Fe2O3 and Fe(0)/FeOOH showed very low activities, suggesting that Fe(oct)2+ in the magnetite structure plays an important role in the reaction. Scanning and high resolution electron microscopies and M?ssbauer spectra (transmission and conversion electron M?ssbauer spectroscopy) indicated that the mechanical alloying process promotes a strong interaction and interface between the metallic and oxide phases, with the Fe(0) particles completely covered by Fe3O4 particles. The high efficiency of the composite Fe(0)/Fe3O4 for Cr(VI) reduction is discussed in terms of a special mechanism where an electron is transferred from Fe(0) to magnetite to reduce Fe(oct)3+ to Fe(oct)2+, which is active for Cr(VI) reduction.