Atmospheric concentrations of PM2.5 trace elements in the Seoul urban area of South Korea

Fine particles (PM2.5) were collected during all four seasons, from April 2001 to February 2002, in Seoul, South Korea, using an annular denuder system. Elemental compositions of ambient PM2.5 were analyzed using the proton-induced X-ray emission method. The greatest contributors (> or = 2%) to the PM2.5 mass were sulfur (S), silicon (Si), chlorine (Cl), aluminum (Al), and iron (Fe) in the spring; S in the summer; and S and Cl in the fall. S, Cl, and Si were the major elements in the winter. S was the most abundant species among the elements, ranging from 5.3 to 7.9%, followed by Si and Cl. From analysis of variance, PM2.5 mass, Al, Si, potassium, calcium, and Fe showed significant seasonal differences during the four seasons (p < 0.001). Enrichment factor (EF) analysis was carried out to identify the sources affecting the aerosol in the Seoul area. On the basis of the mean EF values, elemental S, copper, zinc, and lead may be emitted from anthropogenic sources (EF > 50). Elemental Al, Si, titanium, and Fe may be emitted from crustal sources (EF < 3). Additionally, a correlation analysis was carried out for source identification. The results of the correlation analysis were confirmed by the results of the EF analysis.     

Synoptic evaluation of regional PM2.5 concentrations

By comparing short-term fluctuations in PM2.5 species concentrations among nearby air quality monitors and among species, it becomes possible to understand the regional and local events leading to higher concentrations. This approach was applied at thirteen sites in the Maryland area for the 2001–2006 timeframe in order to identify and explain the behavior of eighteen different analytes as well as the daily Air Quality Index.Findings included identification of local upwind events such as fireworks displays, construction and demolition, the spatial extent of sulfate, nitrate, and ammonium correlations between ground-level monitors, correlations between some crustal species to indicate similar emissions sources in urban areas, and indicators of particle adsorption as a rate-limiting step for certain species. For example, the bromine behavior suggests that bromine concentrations on particulate matter may be limited by the particle adsorption rate and thus show a dependence on the Air Quality Index measurements.     

Elemental composition of PM10 and PM2.5 in urban environment in South Brazil

The purpose of the present study is to analyze the elemental composition and the concentrations of PM₁₀ and PM_2.5 in the Guaíba Hydrographic Basin with HV PM₁₀ and dichotomous samplers. Three sampling sites were selected: 8° Distrito, CEASA and Charqueadas. The sampling was conducted from October 2001 to December 2002. The mass concentrations of the samplers were evaluated, while the elemental concentrations of Si, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu and Zn were determined using the Particle-Induced X-ray Emission (PIXE) technique. Factor Analysis and Canonical Correlation Analysis were applied to the chemical and meteorological variables in order to identify the sources of particulate matter. Industrial activities such as steel plants, coal-fired power plants, hospital waste burning, vehicular emissions and soil were identified as the sources of the particulate matter. Concentration levels higher than the daily and the annual average air quality standards (150 and 50 μg m⁻³, respectively) set by the Brazilian legislation were not observed.     

Seasonal variations of monosaccharide anhydrides in PM1 and PM2.5 aerosol in urban areas

The concentrations of monosaccharide anhydrides (levoglucosan, mannosan, galactosan) in PM1 and PM2.5 aerosol samples were measured in Brno and ?lapanice in the Czech Republic in winter and summer 2009. 56 aerosol samples were collected together at both sites to investigate the different sources that contribute to aerosol composition in studied localities. Daily PM1 and PM2.5 aerosol samples were collected on pre-fired quartz fibre filters.The sum of average atmospheric concentration of levoglucosan, mannosan and galactosan in PM1 aerosol in ?lapanice and Brno during winter was 513 and 273 ng m^?3, while in summer the sum of average atmospheric concentration of monosaccharide anhydrides (MAs) was 42 and 38 ng m^?3, respectively. The sum of average atmospheric concentration of MAs in PM1 aerosol formed 71 and 63% of the sum of MA concentration in PM2.5 aerosol collected in winter in ?lapanice and Brno, whereas in summer the sum of average atmospheric concentration of MAs in PM1 aerosol formed 45 and 43% of the sum of MA concentration in PM2.5 aerosol in ?lapanice and Brno, respectively.In winter, the sum of MAs contributed significantly to PM1 mass ranging between 1.37% and 2.67% of PM1 mass (Brno – ?lapanice), while in summer the contribution of the sum of MAs was smaller (0.28–0.32%). Contribution of the sum of MAs to PM2.5 mass is similar both in winter (1.37–2.71%) and summer (0.44–0.55%).The higher concentrations of monosaccharide anhydrides in aerosols in ?lapanice indicate higher biomass combustion in this location than in Brno during winter season. The comparison of levoglucosan concentration in PM1 and PM2.5 aerosol shows prevailing presence of levoglucosan in PM1 aerosol both in winter (72% on average) and summer (60% on average).The aerosol samples collected in ?lapanice and Brno in winter and summer show comparable contributions of levoglucosan, mannosan and galactosan to the total amount of monosaccharide anhydrides in both aerosol size fractions. Levoglucosan was the most abundant monosaccharide anhydride with a relative average contribution to the total amount of MAs in the range of 71–82% for PM1 aerosols and 52–79% for PM2.5 aerosols.     

Monitoring study of the near-road PM2.5 concentrations in Maryland

The Maryland State Highway Administration (SHA) monitoring program monitored the impact of vehicular emissions on the concentrations of the fine particles smaller than 2.5 microns (PM2.5). PM2.5 concentrations were monitored in close proximity to a highway in order to determine whether traffic conditions on the roadway impact concentrations at this location. The monitoring program attempted to connect monitored concentrations with the roadway traffic exhaust or with the other sources of PM2.5. PM2.5 concentrations were collected near the Capital Beltway (I-495/I-95) in Largo, Maryland. The monitoring program was launched on May 13, 2009 and continued through the end of 2012. Two co-located monitors, one for continuous PM2.5 measurements and the other for speciation measurements, were used in this program. Meteorological and traffic information was also continuously collected at or near the monitoring site. Additionally, data from the two other monitoring locations, one at the Howard University-Beltsville, MD and one at McMillan Reservoir, DC, was used for comparison with the data collected at the SHA monitoring location. The samples collected by the speciation monitor were analyzed at the RTI and DRI Laboratories to determine the composition and the sources of the collected PM2.5 samples. Based on the apportionment analysis, the contribution of roadway sources is about 12 to 17 percent of PM2.5 at the near-road site.

Implications: PM_2.5 monitoring at 150 m (approximately 500 feet) from a major highway in Maryland near Washington, DC, demonstrated that roadway traffic contributes to the total PM_2.5 concentration near the roadway, but the contribution at such distance is small, in the order of 12–17% of the total.     

Investigation of PM2.5 and carbon dioxide levels in urban homes

PM_2.5 (particulate matter with an aerodynamic diameter <2.5 μm) samples were collected in the indoor environments of 15 urban homes and their adjacent outdoor environments in Alexandria, Egypt, during the spring time. Indoor and outdoor carbon dioxide (CO₂) levels were also measured concurrently. The results showed that indoor and outdoor PM_2.5 concentrations in the 15 sites, with daily averages of 45.5 ± 11.1 and 47.3 ± 12.9 µg/m³, respectively, were significantly higher than the ambient 24-hr PM_2.5 standard of 35 µg/m³ recommended by the U.S. Environmental Protection Agency (EPA). The indoor PM_2.5 and CO₂ levels were correlated with the corresponding outdoor levels, demonstrating that outdoor convection and infiltration could lead to direct transportation indoors. Ventilation rates were also measured in the selected residences and ranged from 1.6 to 4.5 hr^?1 with median value of 3.3 hr^?1. The indoor/outdoor (I/O) ratios of the monitored homes varied from 0.73 to 1.65 with average value of 0.99 ± 0.26 for PM_2.5, whereas those for CO₂ ranged from 1.13 to 1.66 with average value of 1.41 ± 0.15. Indoor sources and personal activities, including smoking and cooking, were found to significantly influence indoor levels.

Implications: Few studies on indoor air quality were carried out in Egypt, and the scarce data resulted from such studies do not allow accurate assessment of the current situation to take necessary preventive actions. The current research investigates indoor levels of PM_2.5 and CO₂ in a number of homes located in the city of Alexandria as well as the potential contribution from both indoor and outdoor sources. The study draws attention of policymakers to the importance of the establishment of national indoor air quality standards to protect human health and control air pollution in different indoor environments.     

Correlation between PM concentrations and aerosol optical depth in eastern China

Using one year of Aerosol Optical Depth (AOD) derived from Moderate Resolution Imaging Spectroradiometer (MODIS) on the Terra satellite and particular matter (PM) contents measured at eleven sites located mostly in the eastern China in 2007, the relationship between columnar AOD and hourly and daily average (DA) PM were established. The peak AOD observed from MODIS was generally consistent with the surface PM measurements in eastern China, where Zhengzhou had the maximum annual mean PM₁₀ of 182.1 μg m^?3, while Longfengshan had the minimum annual mean of 38.1 μg m^?3. Ground level observations indicated that PM concentration varies widely across different regions, which was mainly due to the difference in weather conditions and anthropogenic emissions. The coarse particles accounted for the main air pollution in Zhengzhou and Benxi whiles the fine particles, however, were the main constituents in other sites. Results showed that MODIS AOD (averaged over the box of 5 × 5 and 3 × 3 pixels) had a better positive correlation with the coincident hourly average (HA) PM concentration than with DA due to diurnal variation in PM mass measurements. After correcting AOD for relative humidity (RH), the correlation did not improve significantly, suggesting that the RH was not the main factor affecting the correlation of PM with AOD. The statistical regression analysis between MODIS AOD and PM mass suggested that the satellite-derived AOD is a useful tool for mapping PM distribution over large spatial domains.     

Investigation of the time evolved spatial distribution of urban PM2.5 concentrations and aerosol composition during episodic high PM events in Yuma,AZ

An interdisciplinary field study designed to investigate the spatial and temporal variability of atmospheric aerosols during high particulate matter (PM) events along the US–Mexico border near Yuma, AZ was run during the week of March 18, 2007. The experiments were designed to quantify chemical composition and physical phenomena governing the transport of aerosols generated from episodic high PM events. The field study included two micrometeorological monitoring sites; one rural and one urban, equipped with sonic anemometers, continuous particulate concentration monitors and ambient aerosol collection equipment. In addition to the two main monitoring sites, five additional locations were equipped with optical particle counters to allow for the investigation of the spatial and temporal distribution of PM_2.5 in the urban environment. In this paper, the meteorological and turbulence parameters governing the distribution and concentration of PM_2.5 in the urban environment for two high-wind erosion events and one burning event are compared. The interaction between local atmospheric conditions and the particulate distribution is investigated. Results indicate that a single point measurement in the urban area of Yuma may not be sufficient for determining the ambient PM concentrations that the local population experiences; all three high PM events indicated PM_2.5 varied considerably with maximum urban concentrations 5–10 times greater than the measured minima. A comparison of inorganic and carbonaceous content of the aerosols for the three high PM events is presented. The comparison shows an increase in silicon during crustal dust events and an increase in elemental and organic carbon during the burn event. Additional surface chemistry analysis, using time-of-flight secondary ion mass spectrometry (ToF-SIMS), for aerosols collected at the urban and rural sites during the burn event are discussed. The surface chemistry analysis provides positive ion mass spectra of organic and inorganic species in the ambient aerosol, and can be used to determine the type of combustion process that contributed to an increase in PM concentration during the burn event.     

Analysis of PM2.5and PM10 in the Atmosphere of Mexico City during 2000-2002

Abstract

During the last 10 years, high atmospheric concentrations of airborne particles recorded in the Mexico City metropolitan area have caused concern because of their potential harmful effects on human health. Four monitoring campaigns have been carried out in the Mexico City metropolitan area during 2000-2002 at three sites: (1) Xalos-toc, located in an industrial region; (2) La Merced, located in a commercial area; and (3) Pedregal, located in a residential area. Results of gravimetric and chemical analyses of 330 samples of particulate matter (PM) with an aerodynamic diameter less than 2.5 μm (PM_2.5) and PM with an aerodynamic diameter less than 10 μm (PM₁₀) indicate that (1) PM_2.5/PM₁₀ average ratios were 0.42, 0.46, and 0.52 for Xalostoc, La Merced, and Pedregal, respectively; (2) the highest PM_2.5 and PM₁₀ concentrations were found at the industrial site; (3) PM_2.5 and PM₁₀ concentrations were lower at nighttime; (4) PM_2.5 and PM₁₀ spatial averages concentrations were 35 and 76 μg/m³, respectively; and (5) when the PM_2.5 standard was exceeded, nitrate, sulfate, ammonium, organic carbon, and elemental carbon concentrations were high. Twenty-four hour averaged PM_2.5 concentrations in Mexico City and Sao Paulo were similar to those recorded in the 1980s in Los Angeles. PM₁₀ concentrations were comparable in Sao Paulo and Mexico City but 3-fold lower than those found in Santiago.     

Analysis of PM2.5 and PM10 in the atmosphere of Mexico City during 2000-2002

During the last 10 years, high atmospheric concentrations of airborne particles recorded in the Mexico City metropolitan area have caused concern because of their potential harmful effects on human health. Four monitoring campaigns have been carried out in the Mexico City metropolitan area during 2000-2002 at three sites: (1) Xalostoc, located in an industrial region; (2) La Merced, located in a commercial area; and (3) Pedregal, located in a residential area. Results of gravimetric and chemical analyses of 330 samples of particulate matter (PM) with an aerodynamic diameter less than 2.5 microm (PM2.5) and PM with an aerodynamic diameter less than 10 microm (PM10) indicate that (1) PM2.5/PM10 average ratios were 0.42, 0.46, and 0.52 for Xalostoc, La Merced, and Pedregal, respectively; (2) the highest PM2.5 and PM10 concentrations were found at the industrial site; (3) PM2.5 and PM10 concentrations were lower at nighttime; (4) PM2.5 and PM10 spatial averages concentrations were 35 and 76 microg/m3, respectively; and (5) when the PM2.5 standard was exceeded, nitrate, sulfate, ammonium, organic carbon, and elemental carbon concentrations were high. Twenty-four hour averaged PM2.5 concentrations in Mexico City and Sao Paulo were similar to those recorded in the 1980s in Los Angeles. PM10 concentrations were comparable in Sao Paulo and Mexico City but 3-fold lower than those found in Santiago.     

Measurements of PM10 and PM2.5 in urban area of Nanjing,China and the assessment of pulmonary deposition of particle mass

Measurement of PM10 and PM2.5 was carried out at six sites of Nanjing, China in the period of February-May 2001. The pH and conductivity of water-soluble matter of PM10 and PM2.5 were determined, and the samples were analyzed for total carbon (TC), organic carbon (OC) and inorganic carbon (IC) of the water-soluble fraction. The distribution of aerosol mass concentration in size was also measured at one site SB by a nine-stage impactor followed to assess the pulmonary deposition of particles in different tracts of the human respiratory system. Compared with National Ambient Air Quality Standard (NAAQS) of the USA, the level of PM10 and PM2.5 in Nanjing was much higher. Especially for site SY, the average particle mass concentrations (774.5 micrograms/m3 for PM10 and 481.4 micrograms/m3 for PM2.5) were more than five times the NAAQS standard. At site SB aerosol mass distribution in size had shown the similar characteristics with accumulation (Dp < 1 micron) and coarse (Dp > 1 micron) modes. More than 70% of total suspended particles is of a size that they are deposited in the respiratory tract below trachea, whereas about 22% of the mass is respirable and will reach the alveoli. Water-soluble fractions of PM10 and PM2.5 in Nanjing are acidic, and the pH of PM2.5 is lower than that of PM10. OC makes up the majority of TC and accounts for 3-14% of mass concentration of PM10 and/or PM2.5, while IC only accounts for 0.1-0.5% of PM10 and/or PM2.5 mass.     

Assessing urban atmospheric environmental efficiency and factors influencing it in China

Environmental Science and Pollution Research - With rapid urbanization and industrialization in developing countries, cities have become the major sources of air pollution. Studying urban...     

2015年南京市PM2.5与PM10的污染特征

分析了2015年南京市PM2.5和PM10的浓度特征和大致来源类型。PM2.5和PM10的年均浓度分别为56.6 μg·m-3和96.5 μg·m-3,污染水平较高。颗粒物浓度的季节变化特征一致：冬 > 春 > 秋 > 夏;PM2.5的日变化呈"单峰单谷"型,而PM10的呈"单峰双谷"型。颗粒物浓度在城区高于郊区;植被茂盛区域的浓度较低。对PM2.5/PM10而言,比值在冬季和梅雨期较大,分别受取暖和降水的影响;比值在春季和夏末秋初较小,分别受沙尘和秸秆焚烧的影响。PM2.5多为二次颗粒物,PM10多为一次颗粒物;固定污染源对PM2.5的间接贡献和对PM10的直接贡献较移动污染源而言更大。     

天津大气PM_(2.5)中碳组分特征和来源分析

于2014年1—4月在天津城区采集PM2.5样品,采用热光反射法测定样品中有机碳(OC)、元素碳(EC)及8个碳组分(OC1、OC2、OC3、OC4、EC1、EC2、EC3、裂解碳(OP))的含量。结果表明,天津城区空气PM2.5中OC、EC质量浓度分别为(18.7±9.9)、(3.9±2.6)μg/m3,两者之和占PM2.5质量浓度的18.0%。采样期间OC与EC变化趋势一致,均呈现春节期间、普通采暖季浓度较高,非采暖季浓度较低的特点。对8个碳组分进行相关性分析,发现OC1~OC4及EC1~EC3分别来自相似的来源或受大气中类似的二次过程影响,主成分分析结果表明,燃煤、生物质燃烧和机动车排放对天津城区PM2.5中碳组分贡献显著。     

Spatial variability of PM2.5 in urban areas in the United States

Data from the U.S. Environmental Protection Agency's Aerometric Information Retrieval System (now known as the Air Quality System) database for 1999 and 2000 have been used to characterize the spatial variability of concentrations of particulate matter with aerodynamic diameter < or = 2.5 microg (PM2.5) in 27 urban areas across the United States. Different measures were used to quantify the degree of uniformity of PM2.5 concentrations in the urban areas characterized. It was observed that PM2.5 concentrations varied to differing degrees in the urban areas examined. Analyses of several urban areas in the Southeast indicated high correlations between site pairs and spatial uniformity in concentration fields. Considerable spatial variation was found in other regions, especially in the West. Even within urban areas in which all site pairs were highly correlated, a variable degree of heterogeneity in PM2.5 concentrations was found. Thus, even though concentrations at pairs of sites were highly correlated, their concentrations were not necessarily the same. These findings indicate that the potential for exposure misclassification errors in time-series epidemiologic studies exists.     

Estimation of ambient PM2.5 concentrations in Maryland and verification by measured values

In 1997, Maryland had no available ambient Federal Reference Method data on particulate matter less than 2.5 microm in aerodynamic diameter (PM23), but did have annual ambient data for PM smaller than 10 microm (PM10) at 24 sites. The PM10 data were analyzed in conjunction with local annual and seasonal zip-code-level emission inventories and with speciated PM2.5 data from four nearby monitors in the IMPROVE network (located in the national parks, wildlife refuges, and wilderness areas) in an effort to estimate annual average and seasonal high PM2.5 concentrations at the 24 PM10 monitor sites operating from 1992 to 1996. All seasonal high concentrations were estimated to be below the 24-hr PM2.5 National Ambient Air Quality Standards (NAAQS) at the sites operating in Maryland between 1992 and 1996. The estimates also indicated that 12 monitor sites might exceed the 3-year annual average PM2.5 NAAQS of 15 microg/m3, but Maryland's air quality shows signs that it has been improving since 1992. The estimates also were compared with actual measurements after the PM2.5 monitor network was installed. The estimates were adequate for describing the chemical composition of the PM2.5, forecasting compliance status with the 24-hr and annual standards, and determining the spatial variations in PM2.5 across central Maryland.     

The characteristics of PM2.5 in Beijing,China

Weekly PM_2.5 samples were simultaneously collected at a residential (Tsinghua University) and a downtown (Chegongzhuang) site in Beijing from July 1999 through September 2000. The ambient mass concentration and chemical composition of the PM_2.5 were determined. Analyses included elemental composition, water-soluble ions, and organic and elemental carbon. Weekly PM_2.5 mass concentrations ranged from 37 to 357 μg/m³, with little difference found between the two sites. Seasonal variation of PM_2.5 concentrations was significant, with the highest concentration in the winter and the lowest in the summer. Spring dust storms had a strong impact on the PM_2.5. Overall, organic carbon was the most abundant species, constituting no less than 30% of the total PM_2.5 mass at both sites. Concentrations of organic and elemental carbon were 35% and 16% higher at Tsinghua University than at Chegongzhuang. Ammonium, nitrate and sulfate were comparable at the sites, accounting for 25–30% of the PM_2.5 mass.     

Pollution characteristics and toxic effects of PM1.0 and PM2.5 in Harbin,China

Environmental Science and Pollution Research - In 2019, PM2.5 and PM1.0 samples were collected in Harbin City, Heilongjiang Province, China, to research their mass concentration, number...