微波诱导催化剂Fe2O3／沸石氧化处理印染废水

以自制改性沸石为催化剂,通过微波诱导氧化技术,对活性嫩黄模拟废水进行氧化处理。采用尿素均匀沉淀包裹法制备Fe2O3／沸石微波诱导催化剂。利用SEM、XRD、IR等分析手段分别对催化剂的表面形态、物相结构等特性进行表征。实验考察了催化剂用量、微波辐射时间、微波辐射功率对活性嫩黄废水的降解效果。结果表明：在催化剂用量3g／L、微波功率900W、辐射时间4min的条件下,对50mg／L活性嫩黄的处理率达到97％。     

微波诱导Fe2O3/沸石负载型催化剂催化氧化焦化废水的研究

以天然沸石为载体,采用尿素均匀沉淀法制备了Fe2O3/沸石负载型催化剂(简称负载催化剂),研究其在微波辐射下对焦化废水的处理效果,探讨了负载催化剂投加量、微波辐射功率、微波辐射时间等因素对处理效果的影响,并考察了负载催化刑的重复使用性能.结果表明,天然沸石、于350℃焙烧得到的负载催化刑和于550℃焙烧得到的负载催化剂...     

The catalytic incineration of styrene over an Mn2O3/Fe2O3 catalyst

In this study, styrene monomer (SM) was treated by a commercial catalyst, Mn2O3/Fe2O3, in a fixed-bed reactor. The study can be classified into two major parts. First, the effects of operating factors, such as temperature, SM concentration, space velocity, and O2 concentration, on the performance of the catalyst were investigated. Second, two catalyst life tests were carried out to characterize the deactivation effect of SM. The results show that the catalyst results in higher conversion of SM at a higher inlet temperature and higher O2 concentrations. The conversion of SM decreases with increasing SM concentration and space velocity. From the statistical analysis of the data, we find that temperature is the most important factor on the catalytic incineration. Oxygen concentration, SM concentration, and space velocity are significant parameters as well. This paper also provides information on the deactivation effect of SM. The catalysts were characterized by surface and pore-size analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), and electron spectroscopy for chemical analysis (ESCA) before and after the tests. The results show that the catalytic deactivation may be caused by carbon coating, and the pore size and surface area of the catalyst are smaller after deactivation.     

CWAO of phenol using CeO2/gamma-Al2O3 with promoter--effectiveness of promoter addition and catalyst regeneration

The effect of promoter addition on activity of CeO(2)/gamma-Al(2)O(3) was assessed via the CWAO of phenol. Adding Cu as the promoter rendered the most effective performance, followed by Mn, although the performance of Mn-promoted catalyst was inferior to CeO(2)/gamma-Al(2)O(3). Mineralization of phenol was effectively implemented at 160 degrees C using Cu-promoted catalyst (Ce15Cu5). Furthermore, at 180 degrees C this catalyst produced about 100% conversion of phenol (1h) and 95% removal of chemical oxygen demand (4h), higher than that of CeO(2)/gamma-Al(2)O(3). In contrast, Mn-promoted catalyst (Ce15Mn5) required a temperature above 220 degrees C for acceptable performance. Activity of re-used catalyst declined noticeably, due to deposits of carbonaceous compounds and leaching of metal ions. Regeneration with acetone rinsing after the first run was effective in recovering activity of Ce15Cu5, although after a second run further regeneration with acetone rinsing had only a moderate effect, due to residual carbonaceous deposits and the additive effect of leached metal species in each run. As an alternative to acetone, HCl or HNO(3) solution (0.01 M) was less effective at regenerating activity. In promoted catalysts, leached metal ions accounted for the majority of mineralization of phenol, while the solid catalyst played a dual role of initiator and terminator of free radicals. Despite a superior catalytic performance, leaching of Cu(2+) from the promoted catalyst caused a severe decline in activity and poses the problem of secondary pollution of treated wastewater. Therefore, addition of Cu, as well as other metal species, is unfavorable in promoting the CeO(2)/gamma-Al(2)O(3) catalyst.     

改性氧化铝微波诱导催化氧化处理高浓度苯酚废水的研究

采用微波诱导催化氧化技术,以改性氧化铝为催化剂,对高浓度模拟苯酚废水进行氧化处理。考察了微波功率、催化剂投加量、H202投加量、废水pH值和微波反应时间等因素对苯酚去除效果的影响。实验结果表明,处理30mL质量浓度为1 100mg/L的苯酚模拟废水,在微波功率500W,催化剂加入量1 g(液固比30∶1),30％双氧水...     

Lactate oxidation in pyrite suspension: a Fenton-like process in situ generating H2O2

Pyrite is a common mineral at many mining sites. In this study, the mineral pyrite was studied as a Fenton-like reagent for environmental concerns. We selected lactate as a model target molecule to evaluate the Fenton-like catalytic efficiency of pyrite upon organic oxidation. A complete set of control experiments in both aerobic and anaerobic atmospheres unequivocally established that the pyrite in aqueous solution could spontaneously in situ generate OH and H₂O₂, serving as a Fenton-like reagent to catalyze the oxidation of lactate to pyruvate with no need for additional H₂O₂. We called it the pyrite-only Fenton-like (PF) reagent. Monitoring concentration changes of lactate and pyruvate with the time indicated that the pyrite mediated the favorable pyruvate formation at pH 4.5, 60 °C, under air atmosphere. The PF reaction could be stimulated by visible light illumination. Under the optimum conditions, up to 50% of lactate was degraded within 10 d. The results suggest that pyrite and its Fenton-like processes may be potentially practical in wastewater treatment.     

O3氧化工艺处理黄连素制药废水研究

采用臭氧（O3）氧化法处理含高浓度黄连素和COD的制药废水,探讨了废水初始pH、O3投加量及初始黄连素浓度等因素对O3氧化过程的影响,确定了O3氧化技术处理黄连素制药废水的最佳操作条件。结果表明,O3能够有效分解废水中的黄连素,降低其COD浓度;黄连素浓度为700mg／L、COD为3500mg／L、pH为0．88的废水,进气O3浓度为14．05mg／（L·min）,处理时间为180rain（即投加量为2529mg／L）时,黄连素和COD的降解率分别可达77．46％和41．28％,BOD,／COD比（B／C比）从0．06提高到0．34,增加了4．7倍;随着废水中初始黄连素浓度的升高,废水COD降解率逐渐降低。O3氧化法是一种有效的黄连素制药废水预处理技术,可以大大提高废水的可生化性。     

铈改性Al2O3担载Pd催化剂的CO氧化性能研究

浸渍法制备了Al2O3＋CeO2为载体的Pd催化剂,对制备中各因素对催化剂效果的影响作了初步研究。考察了活性组分含量与催化剂性能的关系以及焙烧温度、水蒸气对催化剂活性的影响。结果表明,稀土Ce元素的存在使催化剂的性能得到明显改善。制备过程中焙烧步骤对催化剂的活性影响很大,催化剂制备必须高于600℃焙烧。     

Hierarchical collagen fibers complexed with tannic acid and Fe3+ as a heterogeneous catalyst for enhancing sulfate radical-based advanced oxidation process

Environmental Science and Pollution Research - Efficient sulfate radical-based advanced oxidation processes (SR-AOPs) are important for treating organic contaminants of industrial wastewater. To...     

复合纳米Fe2O3/TiO2可见光催化降解邻甲酚溶液的研究

以复合纳米Fe2O3／TiO2作为催化剂,日光色镝灯为光源,研究了邻甲酚溶液的可见光降解。考察了催化剂制备方法、催化剂使用量、溶液pH、催化剂重复使用等条件对可见光降解的影响。实验结果表明,1％Fe2O3／TiO2（n）对邻甲酚溶液的可见光降解效果最优,比Ti02（p25）的降解率提高了2．6倍。在实验条件下,可见光降解3h,邻甲酚溶液的浓度去除率达95．4％,TOC去除率为72．3％。在较宽的浓度范围内,邻甲酚的反应服从一级动力学反应方程,随着浓度的增大,反应速率常数不断降低。     

Fe (III) supported on resin as effective catalyst for the heterogeneous oxidation of phenol in aqueous solution

FeIII supported on resin as an effective catalyst for oxidation was prepared and applied for the degradation of aqueous phenol. Phenol was selected as a model pollutant and the catalytic oxidation was carried out in a batch reactor using hydrogen peroxide as the oxidant. The influent factors on oxidation, such as catalyst dosage, H2O2 concentration, pH, and phenol concentration were examined by considering both phenol conversion and chemical oxygen demand (COD) removal. The FeIII-resin catalyst possesses a high oxidation activity for phenol degradation in aqueous solution. The experimental results of this study show that almost 100% phenol conversion and over 80% COD removal can be achieved with the FeIII-resin catalyst catalytic oxidation system. A series of prepared resin were investigated for improving the oxidation efficiency. It was found that the reaction temperature and initial pH in solution significantly affected both of phenol conversion and COD removal efficiency. The activity of the catalyst significantly decreased at high pH, which was similar to the Fenton-like reaction mechanism. Results in this study indicate that the FeIII-resin catalytic oxidation process is an efficient method for the treatment of phenolic wastewater.     

超声-过氧化氢-氧化铜组合技术催化氧化水中苯酚

研究了超声-H2O2-CuO组合技术对苯酚的降解效果。考察了苯酚初始浓度、溶液温度及鼓入空气对苯酚去除率的影响。实验结果表明，与未鼓入空气时相比，连续鼓气时苯酚的降解效果较好；初始浓度低，苯酚去除率高；溶液温度从20％上升到55％时，苯酚去除率随温度升高而增大，温度对该过程的影响主要表现为对催化剂的影响而不是对超声作用的影响。高效液相色谱分析表明，苯酚降解的中间产物主要为对苯二酚、邻苯二酚及其他有机小分子物质，最终产物为草酸、二氧化碳和水。     

超声-过氧化氢-氧化铜组合技术催化氧化水中苯酚

研究了超声-H2O2-CuO组合技术对苯酚的降解效果。考察了苯酚初始浓度、溶液温度及鼓入空气对苯酚去除率的影响。实验结果表明,与未鼓入空气时相比,连续鼓气时苯酚的降解效果较好;初始浓度低,苯酚去除率高;溶液温度从20℃上升到55℃时,苯酚去除率随温度升高而增大,温度对该过程的影响主要表现为对催化剂的影响而不是对超声作用的影响。高效液相色谱分析表明,苯酚降解的中间产物主要为对苯二酚、邻苯二酚及其他有机小分子物质,最终产物为草酸、二氧化碳和水。     

O3／H2O2高级氧化技术H2O2加入量的简易控制方法

对与臭氧有着不同反应活性的3类有机污染物，探讨并建立了O3／H2O2高级氧化技术H2O2较优投加量的简易控制方法。结果表明，水中存在溶解臭氧是H2O2与臭氧降解效率具有协同作用的必要条件，另外，H2O2的较优加入量直接依赖于目标有机污染物与臭氧的反应活性。对于不同的有机物及在常规的臭氧化水处理时间内，H2O2加入量控制在单独臭氧化处理时水中溶解臭氧的20-30倍（质量比）之间为宜。这种简易控制H2O2加入量的方法对推广O3／H2O2技术在实际废水处理中的应用具有重要的意义。     

Catalytic oxidation of pentachlorophenol in contaminated soil suspensions by Fe+3-resin/H2O2

Pentachlorophenol (PCP) is a wood preserving agent that is commonly found in contaminated soils at wood treatment sites. The catalytic properties of Fe+3-resin for the oxidation of PCP in aqueous solution and soil suspension with H2O2 were tested. Batch tests in aqueous solution were performed at various dosages of catalyst and H2O2, and reaction temperatures. The results showed that the oxidation of PCP in aqueous solution depends on the dose of H2O2 and the temperature. Essentially complete oxidation of 100 mgl(-1) PCP was obtained with 0.5% Fe+3-resin catalyst, 0.1 M H2O2 and at a reaction temperature of 80 degrees C. The oxidation of PCP achieved in three different soil suspensions was more than 94% within 30-50 min. Moreover, it was demonstrated that the same Fe+3-resin could be reused for at least six cycles of PCP oxidation in soil solutions without loss in efficiency unless the pH of the reaction falls below 5. It was proposed that the loss in used Fe+3-resin catalyst activity could be related to the leaching of Fe+3 at low pH.     

O3/H2O2高级氧化技术H2O2加入量的简易控制方法

对与臭氧有着不同反应活性的3类有机污染物,探讨并建立了O3/H2O2高级氧化技术H2O2较优投加量的简易控制方法.结果表明,水中存在溶解臭氧是H2O2与臭氧降解效率具有协同作用的必要条件,另外,H2O2的较优加入量直接依赖于目标有机污染物与臭氧的反应活性.对于不同的有机物及在常规的臭氧化水处理时间内,H2O2加入量控制在单独臭氧化处理时水中溶解臭氧的20～30倍(质量比)之间为宜.这种简易控制H2O2加入量的方法对推广O3/H2O2技术在实际废水处理中的应用具有重要的意义.     

Degradation of 1,4-dioxane in water with heat- and Fe2+-activated persulfate oxidation

This research investigated the 1,4-dioxane (1,4-D) degradation efficiency and rate during persulfate oxidation at different temperatures, with and without Fe²⁺ addition, also considering the effect of pH and persulfate concentration on the oxidation of 1,4-D. Degradation pathways for 1,4-D have also been proposed based on the decomposition intermediates and by-products. The results indicate that 1,4-D was completely degraded with heat-activated persulfate oxidation within 3–80 h. The kinetics of the 1,4-D degradation process fitted well to a pseudo-first-order reaction model. Temperature was identified as the most important factor influencing the 1,4-D degradation rate during the oxidation process. As the temperature increased from 40 to 60 °C, the degradation rate improved significantly. At 40 °C, the addition of Fe²⁺ also increased the 1,4-D degradation rate. Interestingly, at 50 and 60 °C, the 1,4-D degradation rate decreased slightly with the addition of Fe²⁺. This reduced degradation rate may be attributed to the rapid conversion of Fe²⁺ to Fe³⁺ and the production of an Fe(OH)₃ precipitate which limited the ultimate oxidizing capability of persulfate with Fe²⁺ under higher temperatures. Higher persulfate concentrations led to higher 1,4-D degradation rates, but pH adjustment had no significant effect on the 1,4-D degradation rate. The identification of intermediates and by-products in the aqueous and gas phases showed that acetaldehyde, acetic acid, glycolaldehyde, glycolic acid, carbon dioxide, and hydrogen ion were generated during the persulfate oxidation process. A carbon balance analysis showed that 96 and 93 % of the carbon from the 1,4-D degradation were recovered as by-products with and without Fe²⁺ addition, respectively. Overall, persulfate oxidation of 1,4-D is promising as an economical and highly efficient technology for treatment of 1,4-D-contaminated water.     

Fate of citalopram during water treatment with O3, ClO2, UV and Fenton oxidation

In the present study we investigate the fate of citalopram (CIT) at neutral pH using advanced water treatment technologies that include O₃, ClO₂ oxidation, UV irradiation and Fenton oxidation. The ozonation resulted in 80% reduction after 30 min treatment. Oxidation with ClO₂ removed >90% CIT at a dosage of 0.1 mg L⁻¹. During UV irradiation 85% reduction was achieved after 5 min, while Fenton with addition of 14 mg L⁻¹ (Fe²⁺) resulted in 90% reduction of CIT. During these treatment experiments transformation products (TPs) were formed from CIT, where five compounds were identified by using high resolution and tandem mass spectrometry. Among these desmethyl-citalopram and citalopram N-oxide have been previously identified as human metabolites, while three are novel and published here for the first time. The three TPs are a hydroxylated dimethylamino-side chain derivative, a butyrolactone derivative and a defluorinated derivative of CIT.     

超声辅助电催化氧化降解苯酚的研究

对电催化氧化和超声辅助电催化氧化降解苯酚过程中的UV扫描吸收光谱研究表明:在苯酚的氧化降解反应过程中,都有对紫外光有吸收的中间体生成;对吸光度峰值随降解反应时间的变化关系进行非线性最小二乘法拟合(NLSF),发现溶液的相对吸光度峰值的衰减均符合表观零级反应动力学规律,其相应的表观反应速率常数(k0)分别为(0.0051±0.0005)min-1和(0.0052±0.0003)min-1;但超声波对电催化降解苯酚的速度和效果并无显著影响.同时GC-MS也检测到苯酚超声辅助电催化氧化降解60 min后,发现除苯酚仍然存在外,还有中间产物苯酚乙酸酯、甲酸、乙酸,从而证实苯酚在羟基自由基作用下,开环氧化降解生成乙酸和甲酸等小分子有机物,最后降解为二氧化碳和水.