Performance of the supported copper oxide catalysts for the catalytic incineration of aromatic hydrocarbons

A fixed bed reactor was used to assess the catalytic incineration of toluene by various transition-metal oxide species supported on gamma-Al(2)O(3). CuO/gamma-Al(2)O(3) was found to be the most active of seven catalysts investigated. The CuO species, with a Cu content of 5% (wt), was hence used with four different supports (CeO(2), gamma-Al(2)O(3), TiO(2) and V(2)O(5)) in order to define the optimal combination. Results of the catalytic incineration of toluene, X-ray diffraction (XRD) analysis, oxygen-temperature programmed desorption (O(2)-TPD), toluene-temperature programmed desorption (toluene-TPD) and hydrogen-temperature programmed reduction (H(2)-TPR) showed that CuO/CeO(2) was the most active catalyst, followed by CuO/gamma-Al(2)O(3). The activity of CuO/CeO(2) with respect to the VOC molecule was observed to follow this sequence: toluen>p-xylene>benzene. The addition of water vapor or CO(2) significantly inhibited the activity of the CuO/CeO(2) and CuO/gamma-Al(2)O(3) catalysts. The inhibiting effect of both was reversible for CuO/gamma-Al(2)O(3). For CuO/CeO(2), the inhibiting effect of CO(2) was reversible and even insignificant at a higher temperature (220 degrees C), but the effect of H(2)O vapor was somewhat irreversible at lower incineration temperatures (220 degrees C). For complete oxidation of toluene, the required reaction temperature increased with gas hourly space velocity (GHSV) and toluene inlet concentration.     

Effects of sensitizers on the photodegradation of the systemic fungicide triadimenol

The photochemical behaviour of triadimenol (1) under various conditions has been examined. Significant degradation is obtained only in the presence of electron-acceptor sensitizers as 9,10-dicyanoanthracene or 2,4,6-triphenylpyrylium tetrafluoroborate, and long irradiation times are required. 1H-1,2,4-Triazole (2), 4-chlorophenyl formate (3), 4-chlorophenol (4), 1-(4-chlorophenoxy)-3,3-dimethyl-1-(1H-1,2,4-triazol-1-yl)butan-2-one (5), 4-chlorophenyl 2,2-dimethylpropanoate (6) and 4-chlorobenzoic acid (7) were identified as photoproducts by NMR and GC-MS.     

An investigation into the acid content of aerosols in the ambient air at the Taj Mahal, Agra

A chemical analysis of suspended particulate matter (SPM) collected near the world famous Taj Mahal monument at Agra has been carried out. SPM samples collected on glass fibre filters were analysed for water-soluble sulphate, nitrate, chloride and ammonium ions. The data were derived from over 200 samples (each of 24 h), collected continuously during the winter periods (October through to March) of 1984-1985 and 1985-1986. The SO(4)(2-) and NO(3)(-) components are acidic in nature causing corrosion and effects on visibility, and so were studied in more detail. Mean values for SO(4)(2-) and NO(3)(-) derived from two-year data are 7.2 microg m(-3) and 8.2 microg m(-3), respectively. The SO(4)(2-)/SO(2) and NO(3)(-)/NO(2) ratiosobserved indicate faster conversion of SO(2) to SO(4)(2-) than NO(2) to NO(3)(-), the maximum levels being in January. Thus, both SO(4)(2-) and NO(3)(-) results appear to offer more promising indices of air quality than do SPM data alone.     

Kinetics and mechanism of nitrite oxidation by hypochlorous acid in the aqueous phase

The rate coefficient for the reaction of nitrite with hypochlorite and hypochlorous acid has been studied using spectrophotometric measurements. The reaction rate has been determined in a wide range of H(+) concentration (5< or =-log[H(+)]< or =11). The kinetics were carried out as a function of NO(2)(-), H(+) and total hypochlorite ([HOCl](total)=[HOCl]+[ClO(-)]+[ClNO(2)]) concentrations. The observed overall rate law is described by: -d[HClO](T)dt=[a[NO(2)(-)](2)+b[NO(2)(-)]][H(+)](2)c+d[H(+)]+e[NO(2)(-)][H(+)](2)[HOCl](total)At T=298 K and in Na(2)SO(4) at an ionic strength (I=1.00 M), we obtained using a nonlinear fitting procedure: a=(1.83+/-0.36)x10(7) s(-1), b=(1.14+/-0.23)x10(5) Ms(-1), c=(1.12+/-0.17)x10(-13) M, d=(1.43+/-0.29)x10(-6) M(2) and e=(1.41+/-0.28)x10(3) M where the errors represent 2sigma. According to the overall rate law, a/b=k(1)/k(3), b/e=k(3), c=K(w), d/c=K(a), d=K(a)K(w) and e=K(1)K(a). In Na(2)SO(4) at an ionic strength (I=1.00 M), the values of K(1) and K(a) are (1.1+/-0.1)x10(-4) and 1.28x10(7) M(-1), respectively. A mechanism is proposed for the NO(2)(-) oxidation which involves the reversible initial step: NO(2)(-)+HOCl left harpoon over right harpoon ClNO(2)+OH(-) (K(1)), while ClNO(2) undergoes the two parallel reactions: attack by NO(2)(-) (k(1)) and hydrolysis (k(3)). ClNO(2) and N(2)O(4) are proposed as important intermediates as they control the mechanism. The rate coefficients k(1) and k(3) have been determined at different ionic strengths in NaCl and Na(2)SO(4). The influence of the ionic strength and ionic environment has been studied in this work.     

Bioaccumulation of the lipophilic metabolites of nonionic surfactants in freshwater organisms

Nonylphenol (NP), nonlyphenol monoethoxylate (NP1EO) and nonylphenol diethoxylate (NP2EO) were determined in different freshwater organisms from the surface waters in the Glatt Valley, Switzerland. Rather high concentrations of the compounds investigated have been found to occur in macrophytic algae, particularly Cladophora glomerata (up to 38 mg kg(-1), 80 mg kg(-1), and 28 mg kg(-1) of NP, NP1EO and NP2EO, respectively), the bioconcentration factors of NP reaching up to 10,000. The concentrations in fish were much lower (NP: < 0.03-1.6 mg kg(-1), NP1EO: 0.06-7.0 mg kg(-1), and NP2EO: <0.03-3.1 mg kg(-1) indicating that biomagnification did not take place. Similar concentrations to those in the fish were determined in different tissues of a wild duck. The estimated bioconcentration factors in fish tissues ranged from 13 to 410 for NP, 3 to 300 for NP1EO and 3 to 330 for NP2EO.     

A comparative study of the removal of 3-indolebutyric acid using advanced oxidation processes

In this study, advanced oxidation technologies, namely Fenton Process (FP), Fenton-Like Process (FLP), ozonation (O3) and O3/H2O2 processes, were applied to synthetic wastewater containing 3-indolebutyric acid (IBA). The effectiveness of each process was investigated at different pH values, Fe(+2), Fe(+3), O3 and H2O2 concentrations with respect to the removal efficiencies for chemical oxygen demand (COD) and total organic carbon (TOC). The best removal efficiencies were seen at pH 3 and 2 mM Fe concentration in both FP and FLP, in which the optimum H2O2 concentrations were 6 mM for FP and 10 mM for FLP. Optimum process conditions were pH 12 for the O3 process, pH 9 for the O3/H2O2 process and 1:1 O3/H2O2 molar ratio. The highest COD removal efficiency was 86 percent, obtained in the O3/H2O2 process and the highest TOC removal efficiency was obtained at 77 percent in the FP.     

Abatement of sulfur hexafluoride emissions from the semiconductor manufacturing process by atmospheric-pressure plasmas

Sulfur hexafluoride (SF6) is an important gas for plasma etching processes in the semiconductor industry. SF6 intensely absorbs infrared radiation and, consequently, aggravates global warming. This study investigates SF6 abatement by nonthermal plasma technologies under atmospheric pressure. Two kinds of nonthermal plasma processes--dielectric barrier discharge (DBD) and combined plasma catalysis (CPC)--were employed and evaluated. Experimental results indicated that as much as 91% of SF6 was removed with DBDs at 20 kV of applied voltage and 150 Hz of discharge frequency for the gas stream containing 300 ppm SF6, 12% oxygen (O2), and 40% argon (Ar), with nitrogen (N2) as the carrier gas. Four additives, including Ar, O2, ethylene (C2H4), and H2O(g), are effective in enhancing SF6 abatement in the range of conditions studied. DBD achieves a higher SF6 removal efficiency than does CPC at the same operation condition. But CPC achieves a higher electrical energy utilization compared with DBD. However, poisoning of catalysts by sulfur (S)-containing species needs further investigation. SF6 is mainly converted to SOF2, SO2F4, sulfur dioxide (SO2), oxygen difluoride (OF2), and fluoride (F2). They do not cause global warming and can be captured by either wet scrubbing or adsorption. This study indicates that DBD and CPC are feasible control technologies for reducing SF6 emissions.     

Evaluation of the multiple-ion competition in the adsorption of As(V) onto reclaimed iron-oxide coated sands by fractional factorial design

This study describes the competitive effects of selected ions and natural organic matter on As(V) removal using reclaimed iron-oxide coated sands (RIOCS) in the single- and multi-ion systems. A 2(7-3) factional factorial experimental design (FFD) was employed for screening main competitive factors in this adsorption process. As a result, the inhibitive competition effects of the anions on As(V) removal in the single ion system were in the following sequence: PO(4)(3-)>SiO(3)(2-)>HCO(3)(-)>humic acid (HA)>SO(4)(2-)>Cl(-), whereas the cation Ca(2+) was observed to enhance the As(V) removal. In addition, the optimum initial pH for As(V) removal in single-ion system was 5. Based on the estimates of major effects and interactions from the FFD, PO(4)(3-), SiO(3)(2-), Ca(2+) and HA were important factors on As(V) removal in the multi-ion system. The promoters for the As(V) removal were found to be Ca(2+) and, to a lesser extent, SO(4)(2-). The competitive effects of these ions on As(V) removal were in the order of PO(4)(3-), SiO(3)(2-), HA, HCO(3)(-), and Cl(-). In the single ion system, the efficiencies of As(V) removal range from 75% to 96%, much higher than those in the multi-ion system (44%) at the initial pH 5. Clearly, there were some complex anion interactions in the multi-ion system. To promote the removal of As(V) by RIOCS, it is proposed to lower the pH in the single-ion system, while in the multi-ion system, the increase of the Ca(2+) concentration, or decreases of PO(4)(3-), SiO(3)(2-) and HA concentrations is suggested.     

Study on the photocatalytic degradation of glyphosate by TiO(2) photocatalyst

In this paper, the photocatalytic degradation of glyphosate selected as the deputy of organic pollutant in aqueous solution with TiO(2) powder as a photocatalyst has been studied. The effects of various parameters, such as the amount of the photocatalyst, illumination time, initial pH value, electron acceptors, metal ions, and anions on the photocatalytic degradation of glyphosate were investigated. From the studies, the best condition for the effect of the parameters on the photocatalytic degradation of glyphosate was obtained. The results show that the optimum amount of the photocatalyst used is 6.0 g l(-1) for the photocatalytic reactions. The photodegradation efficiency of glyphosate increases with the increase of the illumination time. With the addition of Fe(3+), Cu(2+), H(2)O(2), K(2)S(2)O(8) or KBrO(3), the photocatalytic degradation of glyphosate is accelerated. However, with the addition of Na(+), K(+), Mg(2+), Ca(2+), Zn(2+), Co(2+) and Ni(2+), or with the addition of trace amounts of Cl(-), Br(-), SO(4)(2-), there are no obvious effects on the reactions. Acidic or alkaline mediums are favorable for the photocatalytic degradation of glyphosate. The possible roles of the additives on the reactions and the possible mechanisms of effect were discussed.     

Atmospheric deposition to the edge of a spruce forest in Denmark

Atmospheric deposition was measured during 1 year at the forest edge of a Norway spruce stand in Denmark. Inside the forest the deposition of H(+), Ca(2+), Mg(2+), Na(+), K(+), Cl(-), NO(3)(-), NH(4)(2) and SO(4)(2-) with canopy throughfall varies with the distance from the forest edge. The deposition at the edge is found to be 10-20 times as high as deposition to an open field and 2-8 times as high as deposition inside the stand. An exponential decrease in deposition as a function of the distance from the forest edge is found. Increased deposition of K(+) and non-sea salt Mg(2+), which mainly originates as a result of leaching from the needles may be explained by a larger leaf area index (LAI) at the forest edge. Deposition of particulate substances, especially Na(+), Cl(-), Mg(2+) and to some extent SO(4)(2-), NH(4)(+) and NO(3)(-) is increased much more than the LAI, which we believe to be caused by changes in wind movements at the forest edge.     

Rainwater chemistry at the summit and southern flank of the Itatiaia massif, Southeastern Brazil

Wet deposition and related rainwater chemistry were studied at the Itatiaia massif, on which is settled the Itatiaia National Park (INP). Samples were simultaneously collected on a weekly basis over 12 months, using automated wet and dry samplers, at the INP-Headquarters (INP-Hq; altitude=820 m) and the Itatiaia Plateau (It-Pt; altitude=2460 m). Conductivity, pH, Na(+), K(+), Mg(2+), Ca(2+), NH(4)(+), Cl(-), NO(3)(-) and SO(4)(2-) were determined in 36 rainwater samples. Volume-weighted mean (VWM) pH was lower at the INP-Hq (4.9) than at the It-Pt (5.3). Very strong correlation between Cl(-) and Na(+) was found for the INP-Hq (r=0.99). At the Itatiaia massif, SO(4)(2-), NO(3)(-), and NH(4)(+) comprised together about 60% of the total inorganic ions and appear to exert the major control on rainwater pH.     

Source apportionment of Phoenix PM2.5 aerosol with the Unmix receptor model

The multivariate receptor model Unmix has been used to analyze a 3-yr PM2.5 ambient aerosol data set collected in Phoenix, AZ, beginning in 1995. The analysis generated source profiles and overall average percentage source contribution estimates (SCEs) for five source categories:gasoline engines (33 +/- 4%), diesel engines (16 +/- 2%), secondary SO4(2-) (19 +/- 2%), crustal/soil (22 +/- 2%), and vegetative burning (10 +/- 2%). The Unmix analysis was supplemented with scanning electron microscopy (SEM) of a limited number of filter samples for information on possible additional low-strength sources. Except for the diesel engine source category, the Unmix SCEs were generally consistent with an earlier multivariate receptor analysis of essentially the same data using the Positive Matrix Factorization (PMF) model. This article provides the first demonstration for an urban area of the capability of the Unmix receptor model.     

Thermochemical studies of the toxic actions of heavy metal ions on Rhizopus nigricans

By using a LKB2277 BioActivity Monitor (heat conduction microcalorimeter), stopped-flow method, the thermogenetic curves of Rhizopus nigricans growth at 25 degrees C inhibited by four kinds of heavy metal ions are determined, parameters such as growth rate constants k, inhibitory ratio I, half inhibitory concentration IC50 et al. are obtained. The experimental results show that heavy metal ions can inhibit Rhizopus nigricans growth obviously, low concentration of Cu2+ has promoting action. The inhibitory sequence is Cd2+ > Hg2+ > Pb2+ > Cu2+, half inhibitory concentration of them are Cd+ 0.8 micro g x ml(-1), Hg2+ 1.7 micro g x ml(-1), Pb2+ 48.0 micro g x ml(-1), Cu2+ 110 micro g x ml(-1). This microclorimetric bioassay for acute cellular toxicity is based on metabolic heat evolution from cultured cells. The assay is quantitative, inexpensive, and versatile; moreover, toxicological information can be obtained with cell from other species of interest.     

Measuring the biodegradability of nonylphenol ether carboxylates, octylphenol ether carboxylates, and nonylphenol

We examined the biodegradability of several metabolites of C8- and C9-alkylphenol ethoxylates, including nonylphenoxyacetic acid (NPEC1), nonylphenoxyethoxyacetic acid (NPEC2), octylphenoxyacetic acid (OPEC1), octylphenoxyethoxyacetic acid (OPEC2), and nonylphenol (NP). Using OECD method 301B (modified Sturm method), OPEC1 and OPEC2 are readily biodegradable: both compounds exceeded 60% of theoretical CO2 formation (ThCO2) by day 28, and required less than 10 days to go from 10% to 60% ThCO2. Also using method 301B, NPEC1 and NPEC2 exceeded 60% ThCO2 at day 28, but did not meet the 10 day window. Using OECD method 301F, the manometric respirometry method that measures oxygen consumption, approximately 62% of NP was biodegraded in 28 days, but required more than 10 days to go from 10% to 60% biodegradation. While the validity of the "10-day window" is currently being debated within OECD, the data show that the common metabolites of C8- and C9-APEs are rapidly degraded in the test systems used, which strongly suggests that they would not accumulate or persist in the environment.     

Precipitation chemistry in the coast of the Metropolitan Region of Rio de Janeiro, Brazil

Precipitation chemistry was studied in the Metropolitan Region of Rio de Janeiro (MRRJ). This study reveals that rainwater in the MRRJ is affected by emissions of air pollutants and provides essential data for future estimates of regional biogeochemical cycles and the impacts of acid deposition on tropical ecosystems. The volume-weighted mean (VWM) pH was 4.77, varying from 3.50 to 6.85. Sea-salt aerosols were the dominant sources of the Na+, Cl- and Mg2+. Excess SO4(2-), Ca2+ and K+ comprised 82, 91, and 87% of their total VWM concentrations, respectively. There were very strong correlations (r > 0.75, P > 0.01) for NO3- and H+, NO3- and excess(exc-)SO4(2-), NH4+ and exc-K+, and exc-SO4(2-) and exc-Ca2+, suggesting causal relationships between these ion pairs. The VWM concentrations of all major ions, except H+, were higher in the dry season, with dry to wet VWM concentration ratios varying from 1.1 (NH4+) to 4.7 (for total K+).     

Decolorization of synthetic dyes by the Fenton reagent and the Cu/pyridine/H2O2 system

Representative azo, triphenylmethane, heterocyclic and polymeric synthetic dyes have been decolorized by two biological non-ezymatic systems, copper/pyridine/H2O2 and the Fenton reagent. With the former system, intensive decolorization measured after 1 h was obtained with phenol red (89%), tropaeolin 00 (58%), Evans blue (95%), eosin yellowish (84%), and Poly B-411 (92%). The rate of decolorization was not affected by pH in the range of 3-9 and increased with increasing temperature. The use of the radical scavengers thiourea and superoxide dismutase showed that hydroxyl radicals rather than superoxide anions are involved in the reaction. Omission of pyridine led to a substantial decrease in the extent of decolorization (20-50% decolorization). The use of organic peroxide instead of H2O2 resulted in slightly slower decolorization, similar values of decolorization being obtained only after a 2-h incubation. Decolorization of the dyes by the Fenton reagent was also very effective but slower than that obtained with the first system. Except for phenol red and eosin yellowish, (decolorization 8% and 52%, respectively) the dyes were decolorized up to 99% after 1-day incubation.     

Ionic composition of PM(10) in the area of Thessaloniki,Greece

Airborne particulate matter (PM(10)) was collected from July 1997 to July 1998 at three locations in the city of Thessaloniki. PM(10) samples were analyzed for Cl(-), NO3(-), SO4(2-), Ca(2+), Mg(2+), Na(+), K(+) and NH4(+). The average PM(10) concentrations were found similar in all three sites with higher values in cold period. The ionic content comprised the 17-23% of the PM(10) mass and sulfate made up the 35-38% of the PM(10) ionic content with an average concentration of 4.80-7.26 microg m(-3). Good correlation was found for SO4(2-) and NO3(-) with Ca(2+), Mg(2+) and Cl(-). Two factors were found to influence the variance of ionic constituents in PM(10) by using factor analysis. Data evaluation considering wind direction showed that higher PM(10) and other ionic concentrations are associated with calm conditions, suggesting influences of local sources.     

Photodegradation of surfactants. XV: Formation of SO4 ions in the photooxidation of sulfur-containing surfactants

Three types of surfactants and related reference compounds containing sulfonate (-SO₃Na), sulfate (-OSO₃Na) or thioether carboxylate (-S-Cn-COOK) group were photodecomposed in an aqueous heterogeneous dispersion system. The photomineralization to SO₄²⁻ions was examined for the surfactants with different chemical structures. The photocatalytic activities of TiO₂ and ZnO were compared for the sulfonates of dodecylbenzene sulfonate (DBS) and polystyrene sulfonate (PSS), the sulfates of sodium dodecyl sulfate (SDS), and the potassium salts of S-dodecylthioglycol acid (TGA), S-dodecylthiopropionic acid (TPA) and S-dodecylthiomalic acid (TMA). ZnO catalyst exhibited higher activity in the formation of SO₄²⁻ion than TiO₂ catalyst.     

Comparison of the degradation of p-hydroxybenzoic acid in aqueous solution by several oxidation processes

A comparative study is made of 12 methods of chemical oxidation applied to degrading p-hydroxybenzoic acid in aqueous solution. The oxidation processes tested were: UV, O3, UV/TiO2, O3/Fe2+, O3/H2O2, O3/UV, UV/H2O2, H2O2/Fe2+, H2O2/Fe2+/O3, UV/H2O2/O3, H2O2/Fe2+/UV and O3/UV/H2O2/Fe2+. The 12 processes were ranked by reactivity. In a kinetic study, the overall kinetic rate constant was split up into three components: direct oxidation by UV irradiation (photolysis), direct oxidation by ozone (ozonation), and oxidation by free radicals (mainly OH*).     

Modeling the reaction kinetics of Fenton's process on the removal of atrazine

The degradation of pesticide, atrazine (ATZ), 2-chloro-4-(ethylamino)-6-(isopropylamino)-s-triazine, by Fenton's reagent (FR) was investigated as a function of reagents' concentrations and ratios in a batch reactor. The degradation of ATZ was effectively achieved by hydroxyl radicals, which were generated in the FR process. The decay rates of ATZ and the oxidation capacities of FR were found to depend on the concentrations of hydrogen peroxide and ferrous ion. The removal kinetics of ATZ are initiated by a rapid decay and then followed by a much slower one. After an extended reaction time (5-10 min), the reactions ceased because the Fe(II) and H(2)O(2) were consumed and would be deactivated in the process. A mathematical model was successfully developed to describe the two-stage reaction kinetics by using two simple but critical parameters: the initial ATZ decay rate and the final oxidation capacity of Fenton's process. In general, higher [Fe(II)] or H(2)O(2) concentrations result in faster initial decay rate and higher oxidation capacity. However, the oxidation capacity is more sensitive to the initial [Fe(II)] due to the presence of side reactions as discussed in the paper.