Improving the activity of Mn/TiO2 catalysts through control of the pH and valence state of Mn during their preparation

In this study, the authors investigated the influence of the valence state of Mn on the efficacy of selective catalytic reduction using a Mn-based catalyst. The nitrogen oxides (NO_x) conversion rate of the catalyst was found to be dependent on the type of TiO₂ support employed and on the temperature, as the catalyst showed an excellent conversion of > 80% at a space velocity of 60,000 hr^?1 when the temperature was above 200 °C. Brunauer-Emmett-Teller, X-ray diffraction, and X-ray photoelectron spectroscopy analyses confirmed that catalyst displaying the highest activity contained the Mn⁴⁺ species and that its valence state was highly dependent on the pH during the catalyst preparation.

Implications Recently, various Mn catalysts have been evaluated as selective catalyst reduction (SCR) catalysts. However, in these previous studies, only the reaction characteristics and catalytic activity on the NH₃ SCR over Mn catalysts were evaluated. There have been no studies on the effect of pH during catalyst preparation. Therefore, in this study, the effect of pH during the catalyst preparation process was examined and a new application of the Mn catalysts was proposed based on the current findings.     

Catalytic gasification of coal using eutectic salts: recovery,regeneration, and recycle of spent eutectic catalysts

Catalyst recovery studies were conducted for gasified chars produced from steam gasification of Illinois #6 coal catalyzed with two different catalyst systems. A ternary (43.5 mol% Li2CO3-31.5 mol% Na2COr-25 mol% K2CO3) and a binary (29 mol% Na2CO3-71 mol% K2CO3) eutectic catalyst system were used for gasifying coal. Various extraction schemes, such as water extraction, H2SO4 extraction, and acetic acid extraction, were evaluated with respect to their extraction efficiencies. Effects of major process variables, such as solvent-to-char ratio, mixing time, temperature, and concentration, on the extraction efficiency were evaluated. A process schematic for the entire catalyst recovery, regeneration, and recycle scheme was developed and the preliminary process economics were determined based on these extraction schemes. H2SO4 extraction was found to be the most desirable. It also turned out to be more attractive than a once-through throwaway system.     

Photochemical and photocatalytic degradation of gaseous toluene using short-wavelength UV irradiation with TiO2 catalyst: comparison of three UV sources

The feasibility of the use of short-wavelength UV (254+185 nm) irradiation and TiO2 catalyst for photodegradation of gaseous toluene was evaluated. It was clear that the use of TiO2 under 254+185 nm light irradiation significantly enhanced the photodegradation of toluene relative to UV alone, owed to the combined effect of photochemical oxidation in the gas phase and photocatalytic oxidation on TiO2. The photodegradation with 254+185 nm light irradiation was compared with other UV wavelengths (365 nm (black light blue lamp) and 254 nm (germicidal UV lamp)). The highest conversion and mineralization were obtained with the 254+185 nm light. Moreover, high conversions were achieved even at high initial concentrations of toluene. Catalyst deactivation was also prevented with the 254+185 nm light. Regeneration experiments with the deactivated catalyst under different conditions revealed that reactive oxygen species played an important role in preventing catalyst deactivation by decomposing effectively the less reactive carbon deposits on the TiO2 catalyst. Simultaneous elimination of photogenerated excess ozone and residual organic compounds was accomplished by using a MnO2 ozone-decomposition catalyst to form reactive species for destruction of the organic compounds.     

非均相催化湿式氧化亚甲蓝水溶液的研究

COD为2000 mg/L的亚甲蓝水溶液作为研究对象,用非均相催化湿式氧化技术进行处理,催化剂性能以COD去除率、脱色率以及稳定性来评价.对4种催化剂担体、15种可溶盐活性组分、4种优选铜催化剂的浸渍液浓度进行筛选,并对铜催化剂进行了改性.实验表明,最佳催化剂担体是FSC,活性组分是Cu(NO3)2,并按催化性能对活性组分进行了排序;浸渍液浓度6wt%Cu2 是最佳选择;改性的Cu-Ce/FSC催化剂与Cu/FSC催化剂相比,COD去除率分别为83.9%和84.5%,出水Cu溶出浓度分别为24.1 mg/L和36.1 mg/L,可见改性催化剂与原催化剂的活性相当,但是稳定性却有了大幅度的提高.     

铁氧化物复合氧化铝催化臭氧化过程中溴酸盐的生成控制

以市售活性炭、硅藻土和氧化铝小球为载体,考察了负载铁基活性组分对催化臭氧化过程中溴酸盐的控制情况,其中,铁基复合氧化铝小球体现出更好的溴酸盐还原特性和催化剂稳定性,证实催化剂中铁氧化物是溴酸盐得到有效控制的主要活性组分。进一步考察了铁基复合氧化铝小球催化臭氧化处理实际原水过程中对溴酸盐的生成控制,以及反应过程中溶解性有机碳（DOC）的去除情况。结果表明,与单独臭氧化相比,该催化剂既能有效去除水中的溶解性有机物,又能明显抑制溴酸盐的生成,反应50h,其活性并没有明显下降。催化剂失活主要归因于吸附位点数量的下降,可以通过负载铁氧化物来实现催化剂的再生。     

A Laboratory Method for the Simulation of Automobile Exhaust and Studies of Catalyst Poisoning

The expected use of catalytic converters on automobiles to meet the legislated automotive emission standards makes desirable a laboratory method that permits realistic testing of these catalysts. Such a method should be versatile enough to simulate a wide range of conditions which are applicable for catalysts designed to oxidize hydrocarbons and carbon monoxide, or to reduce nitric oxide, as the case may be. For this purpose, we have modified a pulse-flame combustor, based on a design by Meguerian. The output of this simulator very closely resembles engine exhaust with respect to composition, space velocity, and contaminants. The durability of a monolithic or pelleted catalyst can be evaluated by long term exposure to the simulated exhaust and by periodic measurement of the catalyst activity as a function of temperature. The apparatus and the range of conditions that can be achieved are described in detail. Poisoning of a Pt catalyst by fuels containing low concentrations of lead was studied with this exhaust simulator and compared with results obtained in engine dynamometer tests; a satisfactory correlation of catalyst deterioration was established.     

V2O5-TiO2-AlF3/Al2O3催化臭氧化2,4-滴丙酸的氧化效能

为了提高有机物的臭氧化降解效率,工作中利用浸渍法制备了一种新型的三组分催化剂(记为V2O5-TiO2-AlF3/Al2O3)。催化臭氧化降解2,4-滴丙酸的实验结果表明,该催化剂能有效提高臭氧化的效率,体系可能遵循羟基自由基的作用机理。利用相对法计算结果表明,与单独臭氧化相比,V2O5-TiO2-AlF3/Al2O3催化臭氧化体系具有更大的Rct值。重复实验结果表明,该催化剂具有相对较好的稳定性。以上研究结果对推广催化臭氧化技术在实际废水处理中的应用具有重要的实际意义。     

汉沙黄/TiO_2光催化剂的制备及其光催化活性

采用溶剂热合成法制备了一种新型的汉沙黄/TiO2复合物光催化剂,利用多种手段SEM、XRD、FT-IR对催化剂的样品形貌、结构进行表征。分别以罗丹明B、亚甲基蓝、中性红为目标降解物,考察了可见光下溶液pH值对催化剂的吸附性能和催化活性的影响。结果表明,敏化后的TiO2对光的响应由紫外区扩展到可见区,催化活性优于纯TiO2,对上述3种染料的吸附率分别为19.2%、29.2%和43.2%,降解率分别为98.6%、92.5%和97.8%。制备的汉沙黄/TiO2光催化剂稳定性好,重复使用率高,在印染废水处理中具有很好的应用前景。     

A study on production of biodiesel using a novel solid oxide catalyst derived from waste

The issues of energy security, dwindling supply and inflating price of fossil fuel have shifted the global focus towards fuel of renewable origin. Biodiesel, having renewable origin, has exhibited great potential as substitute for fossil fuels. The most common route of biodiesel production is through transesterification of vegetable oil in presence of homogeneous acid or base or solid oxide catalyst. But, the economics of biodiesel is not competitive with respect to fossil fuel due to high cost of production. The vegetable oil waste is a potential alternative for biodiesel production, particularly when disposal of used vegetable oil has been restricted in several countries. The present study evaluates the efficacy of a low-cost solid oxide catalyst derived from eggshell (a food waste) in transesterification of vegetable oil and simulated waste vegetable oil (SWVO). The impact of thermal treatment of vegetable oil (to simulate frying operation) on transesterification using eggshell-derived solid oxide catalyst (ESSO catalyst) was also evaluated along with the effect of varying reaction parameters. The study reported that around 90 % biodiesel yield was obtained with vegetable oil at methanol/oil molar ratio of 18:1 in 3 h reaction time using 10 % ESSO catalyst. The biodiesel produced with ESSO catalyst from SWVO, thermally treated at 150 °C for 24 h, was found to conform with the biodiesel standard, but the yield was 5 % lower compared to that of the untreated oil. The utilization of waste vegetable oil along with waste eggshell as catalyst is significant for improving the overall economics of the biodiesel in the current market. The utilization of waste for societal benefit with the essence of sustainable development is the novelty of this work.     

Photocatalytic degradation of phenol using Ag core-TiO<Subscript>2</Subscript> shell (Ag@TiO<Subscript>2</Subscript>) nanoparticles under UV light irradiation

Ag@TiO₂ nanoparticles were synthesized by one pot synthesis method with postcalcination. These nanoparticles were tested for their photocatalytic efficacies in degradation of phenol both in free and immobilized forms under UV light irradiation through batch experiments. Ag@TiO₂ nanoparticles were found to be the effective photocatalysts for degradation of phenol. The effects of factors such as pH, initial phenol concentration, and catalyst loading on phenol degradation were evaluated, and these factors were found to influence the process efficiency. The optimum values of these factors were determined to maximize the phenol degradation. The efficacy of the nanoparticles immobilized on cellulose acetate film was inferior to that of free nanoparticles in UV photocatalysis due to light penetration problem and diffusional limitations. The performance of fluidized bed photocatalytic reactor operated under batch with recycle mode was evaluated for UV photocatalysis with immobilized Ag@TiO₂ nanoparticles. In the fluidized bed reactor, the percentage degradation of phenol was found to increase with the increase in catalyst loading.     

Catalytic combustion of methane over commercial catalysts in presence of ammonia and hydrogen sulphide

The performance of different commercially available catalysts (supported Pd, Pt, Rh, bimetallic Pd-Pt, and Cr-Cu-Ti oxide catalyst) for the oxidation of methane, alone and in presence of ammonia and hydrogen sulphide is studied in this work. Catalysts performance was evaluated both in terms of activity and resistance to poisoning. The main conclusions are that supported Pd and Rh, present the highest activities for methane oxidation, both alone and in presence of ammonia, whereas they are severely poisoned in presence of H2S. Pt and Cr-Cu-Ti are less active but more sulphur resistant, but their activity is lower than the residual activity of sulphur-deactivated Pd and Rh catalysts. The Pd-Pt catalyst exhibits low activity and it is quickly deactivated in presence of hydrogen sulphide.     

超声辅助La-TiO_2/膨胀珍珠岩的吸附与光催化性能

以膨胀珍珠岩（expanded perlite,EP）为载体,以钛酸正丁酯和硝酸镧为前驱体,采用浸渍法制备出掺杂镧的漂浮型La-TiO2/EP光催化剂,采用X-射线粉末衍射研究了催化剂的形态结构。以正辛烷为模拟水面烃类污染物,通过超声波辅助对此催化剂的吸附与光催化性能进行了研究。结果表明：以20～40目的膨胀珍珠岩为载体制备的5%La-TiO2/EP,经500℃焙烧2 h后对辛烷的去除效果最好。超声波可促进辛烷在催化剂表面的吸附与迁移,超声辅助下辛烷去除率可提高11.08%。     

Application of pier waste sludge for catalytic activation of proxy-monosulfate and phenol elimination from a petrochemical wastewater

This investigation aimed to remove phenol from real wastewater (taken from a petrochemical company) by activating peroxy-monosulfate (PMS) using catalysts extracted from pier waste sludge. The physical and chemical properties of the catalyst were evaluated by FE-SEM/EDS, XRD, FTIR, and TGA/DTG tests. The functional groups of O–H, C–H, CO₃^2?, C–H, C–O, N–H, and C–N were identified on the catalyst surface. Also, the crystallinity of the catalyst before and after reaction with petrochemical wastewater was 103.4 nm and 55.8 nm, respectively. Operational parameters of pH (3–9), catalyst dose (0–100 mg/L), phenol concentration (50–250 mg/L), and PMS concentration (0–250 mg/L) were tested to remove phenol. The highest phenol removal rate (94%) was obtained at pH=3, catalyst dose of 80 mg/L, phenol concentration of 50 mg/L, PMS concentration of 150 mg/L, and contact time of 150 min. Phenol decomposition in petrochemical wastewater followed the first-order kinetics (k> 0.008 min^?1, R²> 0.94). Changes in pH factor were very effective on phenol removal efficiency, and maximum efficiency (≈83%) was achieved in pH 3. The catalyst stability test was performed for up to five cycles, and phenol removal in the fifth cycle was reduced to 42%. Also, the energy consumption in this study was 77.69 kW h/m³. According to the results, the pier waste sludge catalyst/PMS system is a critical process for eliminating phenol from petrochemical wastewater.

     

超声辅助La-TiO2/膨胀珍珠岩的吸附与光催化性能

以膨胀珍珠岩(expanded perlite,EP)为载体,以钛酸正丁酯和硝酸镧为前驱体,采用浸渍法制备出掺杂镧的漂浮型La-TiO2/EP光催化剂,采用X-射线粉末衍射研究了催化剂的形态结构。以正辛烷为模拟水面烃类污染物,通过超声波辅助对此催化剂的吸附与光催化性能进行了研究。结果表明:以20～40目的膨胀珍珠岩为载体制备的5%La-TiO2/EP,经500℃焙烧2 h后对辛烷的去除效果最好。超声波可促进辛烷在催化剂表面的吸附与迁移,超声辅助下辛烷去除率可提高11.08%。     

Catalytic Gasification of Coal Using Eutectic Salts: Recovery,Regeneration, and Recycle of Spent Eutectic Catalysts

Abstract

Catalyst recovery studies were conducted for gasified chars produced from steam gasification of Illinois #6 coal catalyzed with two different catalyst systems. A ternary (43.5 mol% Li₂ CO₃ –31.5 mol% Na₂ CO₃ –25 mol% K₂ CO₃ ) and a binary (29 mol% Na₂ CO₃ –71 mol% K₂ CO₃ ) eutectic catalyst system were used for gasifying coal. Various extraction schemes, such as water extraction, H₂ SO₄ extraction, and acetic acid extraction, were evaluated with respect to their extraction efficiencies. Effects of major process variables, such as solvent-to-char ratio, mixing time, temperature, and concentration, on the extraction efficiency were evaluated. A process schematic for the entire catalyst recovery, regeneration, and recycle scheme was developed and the preliminary process economics were determined based on these extraction schemes. H₂ SO₄ extraction was found to be the most desirable. It also turned out to be more attractive than a once-through throwaway system.     

New catalyst comprising Silicotungstic acid and MCM-22 for degradation of some organic dyes

A heterogeneous catalyst comprising Keggin type polyoxometalate, silicotungstic acid (SiW₁₂), and MCM-22 was synthesized using wet impregnation method and characterized by acidity measurement, BET, FT-IR, XRD, and SEM. Their catalytic activity was evaluated for the degradation of cationic organic dyes like methylene blue (MB), crystal violet (CV), and an azo dye Chryosidine Y (CY) in an aqueous solution. The experimental parameters such as catalyst amount, initial dye concentration, and contact time were studied for the degradation of dyes, and it was found that the cationic dyes like methylene blue and crystal violet show better activity as compared to azo dye Chryosidine Y. This may be attributed to better electrostatic interaction of these cationic dyes with the residual negative surface charge of the catalyst, due to presence of SiW₁₂ ion as it is rich in surface oxygens and surface hydroxyl groups. The control experimental results showed that the presence of SiW₁₂ at the surface of MCM-22 promoted the degradation reactions, and presence of multiple W–O bonds in polyoxometalate also played a key role in this reaction. The catalyst exhibits recycling ability without any significant loss in activity up to four cycles.

     

B,N和Ce共掺杂TiO2催化剂光催化活性研究

采用溶胶-凝胶法制备出B,N和Ce共掺杂TiO2光催化剂,并用XRD、SEM等表征了其结构特征。以酸性大红染料溶液的光催化降解为探针反应,考察了制备条件对共掺杂TiO2催化剂活性的影响。结果表明,在400℃,当B,N和Ce的原子比为1∶2∶0.1,焙烧3 h时,光催化剂活性最大,大红染料的降解率达到98%。     

Improving ozonation to remove carbamazepine through ozone-assisted catalysis using different NiO concentrations

The carbamazepine (CBZ) abatement is herein evaluated using catalytic ozonation at different NiO concentrations as catalyst: 100, 300, and 500 mg      

La1-x Cex Cuy Mn1-yO3／HZSM-5催化剂低温去除柴油机碳烟和NOx

为实现对柴油机碳烟和NOx的低温同步去除,采用柠檬酸络合法制备分子筛负载钙钛矿型金属复合氧化物催化剂,应用x衍射分析仪（XRD）和电镜扫描仪（SEM）对催化剂性能进行表征,并在微型固定床反应器中对催化剂低温去除碳烟和NOx进行活性评价。利用程序升温反应（TPR）技术,进行催化剂活性评价、柴油机负荷和排放等特性实验。结果表明,A位用适量Ce部分取代La,B位用适量cu部分取代Mn,可使碳颗粒燃烧温度降低,CO2选择性好,NOx转化率升高。La0.4 Ce0.6 Cu0.2 Mn0.8O3／HZSM-5催化剂的最大NOx转化率为81．0％,Ti、Tm和Tf分别为250、350和475℃,表明该催化剂具有较好的催化活性,能在低温条件下去除碳烟和NOx。     

Effectiveness of zerovalent iron and nickel catalysts for degrading chlorinated solvents and n-nitrosodimethylamine in natural groundwater.

Laboratory batch experiments were performed to evaluate the effectiveness of nickel catalysts, nanoscale zerovalent iron (nZVI) doped with palladium, and microscale ZVI for treatment of tetrachloroethene, trichloroethene, and n-nitrosodimethylamine (NDMA) in soil-groundwater slurries. Results indicated that the presence of NDMA inhibited degradation of chlorinated solvents. Although both the nickel catalyst and nZVI were able to degrade NDMA in deionized water, neither of these metals was effective at degrading NDMA in the soil-groundwater system evaluated in this study. The effectiveness of the nickel catalyst and nZVI, with respect to treatment of the chlorinated solvents, also appeared to be highly dependent on the groundwater geochemical conditions. Overall results of this study suggest that the degradation mechanisms involving nickel catalysts and nZVI in natural soil/groundwater systems are not well-understood, and addition of metal catalysts to ZVI may not necessarily enhance observed degradation rates in natural systems.