Comparison of photocatalytic degradation of dyes in relation to their structure

The photocatalytic degradation of a series of six acid dyes (Direct Red 80, Direct Red 81, Direct Red 23, Direct Violet 51, Direct Yellow 27, and Direct Yellow 50) has been tested compared in terms of color removal, mineralization, and toxicity (Lactuca sativa L. test) after photocatalysis on immobilized titanium dioxide. The dyes were examined at their natural pH and after hydrolysis at pH 12. Results show that hydrolysis decreases strongly the efficiency of color removal, that full mineralization takes much longer reaction time than color removal, and that toxicity is only very partially reduced. Some structural parameters, related to the structure and the topology of the dye molecules, could be correlated with the apparent color removal rates at natural pH.     

Decomposition of low-concentration gas-phase toluene using plasma-driven photocatalyst reactor

Plasma-driven photocatalysis system was prepared and performed. To overcome the treatment difficulty of volatile organic compounds, non-thermal plasma was used as a light source of photocatalysis. The removal of low-concentration toluene was investigated and secondary products were analyzed by gas chromatograph–mass spectroscopy. The plasma-driven photocatalyst reactor using direct current as a light source and titanium dioxide catalyst loaded on activated carbon fiber (TiO₂/ACF) as photocatalyst was studied. It was found that plasma-driven photocatalysis system could significantly increase the removal effect of toluene. The number of secondary products was largely decreased. It means that plasma-driven photocatalysis hybrid system was an effective method for the removal of volatile organic compounds.     

Model reactor for photocatalytic degradation of persistent chemicals in ponds and waste water

A laboratory scale flow-through model reactor for the degradation of persistent chemicals using titanium dioxide (TiO₂) as photocatalyst immobilized on glass beads is presented. In the test system with a volume of 18 L contaminated water is pumped to the upper part of the floating reactor and flows over the coated beads which are exposed to UV-radiation. The degradation of two dyes of different persistance was investigated. Primary degradation of methylene blue did not fit a first order kinetic due to coincident adsorption onto the photocatalyst and direct photolysis, resulting in a half-life of 6 h. A filtrate of a green algae suspension accelerated the colour removal. In contrast, reactive red 2 was degraded only by photocatalysis; neither adsorption nor direct photolysis led to a colour removal. The course of primary degradation followed a first order kinetic with a half-life of 18 h and a rate constant of 0.04 h⁻¹. Analysis of the degradation products indicated mineralization by detection of NO₂⁻ and NO₃⁻, accompanied by a decrease of pH and an increase of conductivity. A successful adaptation of the model reactor (scale 1:10) to dimensions required for surface waters and waste water treatment plants would be a costefficient and environmentally sustainable application of photocatalysis for the treatment of industrially polluted water and could be of relevance for third world contries, particularly those favoured by high solar radiation.     

超声波-光催化联合降解苯酚废水研究

超声降解和光催化降解均为自由基历程的高级氧化技术,同时,超声空化能够改善传质效果,因此,二者耦合能否产生协同效果是值得研究的。本文考察了苯酚溶液的超声降解、光降解、光催化降解、超声-光催化降解以及温度对光降解和光催化降解的影响。结果表明,40kHz,0.4w/cm2的超声波对苯酚没有明显的降解作用,而对光催化降解只有轻微的促进作用。光降解和光催化降解的过程曲线显著不同,但温度对二者均有显著的促进作用。     

Comparison of various advanced oxidation processes for the degradation of phenylurea herbicides

Various types of advanced oxidation processes (AOPs), such as UV photolysis, ozonation, heterogeneous photocatalysis and their combinations were comparatively examined at the same energy input in a home-made reactor. The oxidative transformations of the phenylurea herbicides fenuron, monuron and diuron were investigated. The initial rates of transformation demonstrated that UV photolysis was highly efficient in the cases of diuron and monuron. Ozonation proved to be much more effective in the transformation of fenuron than in those of the chlorine containing monuron and diuron. In heterogeneous photocatalysis, the rate of decomposition decreased with increase of the number of chlorine atoms in the target molecule. Addition of ozone to UV-irradiated solutions and/or TiO₂-containing suspensions markedly increased the initial rates of degradation. Dehalogenation of monuron and diuron showed that each of these procedures is suitable for the simultaneous removal of chlorinated pesticides and their chlorinated intermediates. Heterogeneous photocatalysis was found to be effective in the mineralization.     

Photocatalytic ozonation of pesticides in a fixed bed flow through UVA-LED photoreactor

In this study, a fixed bed flow through UVA-LED photoreactor was used to compare the efficiency of ozone, photocatalysis and photocatalysis-ozone degradation, and mineralization of two pure pesticides, 2,4-dichlorophenoxyacetic acid (2,4-D) and 2-methyl-4-chlorophenoxyacetic acid (MCPA), and a commercial one, Killex®. For the degradation of the parent compounds, ozone-based processes were more effective. While for mineralization, photocatalytic processes were more effective. Photocatalytic ozonation was the most efficient process for both the degradation and mineralization of the parent compounds. The degradation rates and mineralization by photocatalytic ozonation were higher than the summation of the corresponding rates by ozonation and photocatalysis, indicating a symbiotic relationship.Overall, the photocatalytic ozonation process with the fixed bed TiO₂ reduces the time needed for the degradation and mineralization of the pesticides, reduces the costs of powder catalyst separation and overcomes the reduced efficiency of immobilized catalysts, which makes the process quite attractive for practical applications.     

Degradation of industrial surfactants by photocatalysis combined with ozonation

The efficiency of titanium dioxide-mediated photocatalytic degradation of pollutants can be enhanced by combination with another advanced oxidation procedure such as ozonation. Mineralization of hydroxy- and dihydroxybenzenesulfonate based on these methods, both individually and combined, was investigated by monitoring the total organic carbon content, sulfate concentration, pH, high-performance liquid chromatography as well as the absorption spectral changes. The mineralization efficiency of the combined procedure significantly exceeded the sum of those of the individual techniques. The comparison of the disappearance of the starting material and the formation of the sulfate ions indicates that desulfonation is not the primary step of the degradation. Moreover, in the case of the combined method, ring cleavage, and thus, partial mineralization can occur without desulfonation. Efficient degradation of other, widely used industrial surfactants, such as alkylbenzene sulfonates and alkyl ether sulfates, was also achieved by heterogeneous photocatalysis combined with ozonation, offering an applicable method for the removal of these pollutants.     

Titanium dioxide mediated photocatalytic degradation of 17beta-estradiol in aqueous solution

Photocatalytic degradation of 17beta-estradiol (E2) in aqueous medium mediated with titanium dioxide (TiO(2)) was studied. Moreover, effect of TiO(2) dosage on the degradation efficiency was investigated. Particular attention was paid to the identification of intermediates and analysis of photocatalytic degradation mechanism of E2 under neutral and alkaline conditions. The degradation efficiency of E2 increased with increasing concentration of TiO(2) but decreased due to light scattering as TiO(2) concentration was greater than 0.5mgml(-1). Several intermediates were formed during photocatalytic degradation of E2. However, only a few of the compounds could be identified and confirmed by LC-MS and LC-MS/MS. Six intermediates were observed by photocatalytic oxidation under alkaline conditions, namely 2-hydroxyestradiol, 10epsilon-17beta-dihydroxy-1,4-estradien-3-one (DEO), 10epsilon-hydroperoxide-17beta-hydroxy-1,4-estradien-3-one and three kinds of dicarboxylic acids formed by the opening of aromatic ring. In addition to the six intermediates mentioned above, 17beta-hydroxy-1,4-estradien-3-one (EO) was observed under neutral conditions and in the presence of methanol. Based on these intermediates, which were hardly degraded even after E2 was fully degraded, the mechanism of E2 degradation by TiO(2) photocatalysis was elucidated.     

Photodegradation of haloacetic acids in water

The global distribution and high stability of some haloacetic acids (HAAs) has prompted concern that they will tend to accumulate in surface waters and pose threats to humans and the ecosystem. It is important to study the degradation pathways of HAAs in aqueous systems to understand their ecotoxicological effects. Previous studies involving thermal degradation reactions show relatively long lifetimes for HAAs in the natural environment. Photolysis and photocatalytic dissociation are potentially efficient routes for the degradation of HAAs such as trichloroacetic acid to hydrochloric acid, carbon dioxide and chloroform, although such processes are poorly understood in surface waters. In our present study, we have used light to degrade the HAAs in the presence of titanium dioxide suspensions. All chloro and bromo HAAs degrade in photocatalysis experiments and the rate of degradation is directly proportional to the number of halogen atoms in the acid molecule. The half-lives of the HAAs from the photodegradation at 15 degrees C in the presence of suspended titanium dioxide photocatalyst are 8, 14, 83 days for the tri-, di- and mono-bromoacetic acids. Tri-, di- and mono-chloroacectic acids have half-lives of 6, 10 and 42 days respectively. The mixed bromochloro and chlorodifluoroacetic acids degrade with half-lives of 18 and 42 days respectively. Our results therefore suggest that the photocatalytic process can provide an additional degradation pathway for the HAAs in natural waters.     

Light-induced degradation of perfluorocarboxylic acids in the presence of titanium dioxide

The UV-photon-induced degradation of heptafluorobutanoic acid was investigated in acidic aqueous solutions in the presence of titanium dioxide. Heptafluorobutanoic acid could be degraded with this photocatalyst in a light-induced reaction generating carbon dioxide and fluoride anions. Carbon dioxide evolution in a significant amount occurred only in the presence of molecular oxygen and the photocatalyst. The light-induced degradation of trifluoroacetic acid, pentafluoropropanoic acid, nonafluorobutanoic acid, pentadecafluorooctanoic acid, nonafluorobutanesulfonic acid, and heptadecafluorooctanesulfonic acid in the presence of titanium dioxide was also studied. The perfluorocarboxylic acids under investigation are degraded to generate CO(2) and fluoride anions while both perfluorinated sulfonic acids are persistent under the experimental conditions employed in this study. For all compounds photonic efficiencies of the mineralization reaction were estimated to be smaller than 1x10(-5). To increase the photocatalytic activity mixed systems containing homogeneous phosphotungstic acid and heterogeneous titanium dioxide catalysts were also investigated. In the mixtures of these two photocatalysts, the formation rate of CO(2) increased with illumination time.     

Synergy of ozonation and photocatalysis to mineralize low concentration 2,4-dichlorophenoxyacetic acid in aqueous solution

Concentration of 2,4-dichlorophenoxyacetic acid (2,4-D) may affect its degradation kinetics in advanced oxidation systems, and combinations of two or more systems can be more effective for its mineralization at low concentration levels. Degradations and mineralizations of 0.045mM 2,4-D using O(3), O(3)/UV, UV/TiO(2) and O(3)/UV/TiO(2) systems were compared, and influence of reaction temperature on the mineralization in O(3)/UV/TiO(2) system was investigated. 2,4-D degradations by O(3), O(3)/UV and UV/TiO(2) systems were similar to the results of earlier investigations with higher 2,4-D concentrations. The degradations and total organic carbon (TOC) removals in the four systems were well described by the first-order reaction kinetics. The degradation and removal were greatly enhanced in O(3)/UV/TiO(2) system, and further enhancements were observed with larger O(3) supplies. The enhancements were attributed to hydroxyl radical (()OH) generation from more than one reaction pathway. The degradation and removal in O(3)/UV/TiO(2) system were very efficient with reaction temperature fixed at 20 degrees C. It was suspected that reaction temperature might have influenced ()OH generation in the system, which needs further attention.     

太阳能固定膜光催化去除双酚A的特性与效果

以太阳能固定膜光催化中试装置,研究了光解、初始浓度和平均光强等对双酚A(BPA)光催化去除的影响及BPA的矿化和在自来水中的处理效果.试验结果表明,BPA在日光照射下很难光解,其光催化降解呈表观一级反应,在平均光强介于5.7～23.5 W/m2时,表观反应速率常数和平均光强呈线性关系.太阳能光催化对BPA具有良好的矿化作用,但其降解与以UV254为光源的降解有不同的机理.太阳能光催化对自来水中BPA也具有较好的处理效果.     

Novel imazethapyr detoxification applying advanced oxidation processes

Different degradation methods have been applied to assess the suitability of advanced oxidation process (AOPs) to promote mineralization of imazethapyr [(RS)-5-ethyl-2-(4-isopropyl-4-methyl-5-oxo-2-imidazolin-2-yl)nicotinic acid], a widely used imidazolinone class herbicide, the persistence of which has been demonstrated in surface and ground waters destined to human uses. Independent of the oxidation process assessed, the decomposition of imazethapyr always followed a pseudo-first order kinetic. The direct UV-irradiation (UV) of the herbicide as well as its oxidation with ozone (O?), and hydrogen peroxide tied to UV-irradiation (H?O?/UV) were sufficiently slow to permit the identification of intermediate products, the formation pathway of which has been proposed. Ozonation joined to UV-irradiation (O?/UV), ozonation joined to titanium dioxide photo-catalysis (TiO?/UV+O?), sole photo-catalysis (TiO?/UV), and photo-catalysis reinforced with hydrogen peroxide-oxidation (TiO?/UV+H?O?) were characterized by a faster degradation and rapid formation of a lot of small molecules, which were quickly degraded to complete mineralization. The most effective oxidation methods were those using titanium dioxide photo-catalysis enhanced either by ozonation or hydrogen peroxide. Most of all, these last processes were useful to avoid the development of dangerous by-products.     

Degradation of Carbofuran in Water by Solar Photocatalysis in Presence of Photosensitizers

The effect of the presence of photosensitizers, methylene blue (MB) and rose Bengal (RB), on the degradation of carbofuran (2,3-dihydro-2,2-dimethylbenzofuran-7-yl methylcarbamate) in water in a solar photocatalytic system was investigated. It was found that as compared to MB, RB generally showed a stronger effect on the decomposition of carbofuran under comparable conditions. Among the conditions studied, adding 2 × 10^?6 M of RB, that corresponding to 2% of the initial concentration of carbofuran solution in the system, rendered the most effective degradation of carbofuran. As a result, a carbofuran removal percentage of 69.9%, a mineralization efficiency of 28.0%, and a microtoxicity reduction of 65.0% could be achieved. The degradation and mineralization of carbofuran was found to follow the pseudo-first order reaction kinetics. The decomposition mechanism of carbofuran was further investigated through identification of the intermediates to elaborate the influence of dye photosensitizer on the solar photocatalysis of carbofuran in water. On the basis of the intermediates identified, including carbofuran phenol, 3-hydroxy carbofuran phenol, and substituted alcohols (3-phenoxy 1-propanol, 2-ethyl 1-hexanol, 2-butoxyl ethanol), it appears that hydrolysis and hydroxylation were the two key mechanisms for decomposing carbofuran during the process of solar photocatalysis with the aid of dye photosensitizer.     

Kinetics and mechanism of TNT degradation in TiO2 photocatalysis

The photocatalytic degradation of TNT in a circular photocatalytic reactor, using a UV lamp as a light source and TiO(2) as a photocatalyst, was investigated. The effects of various parameters such as the initial TNT concentration, and the initial pH on the TNT degradation rate of TiO(2) photocatalysis were examined. In the presence of both UV light illumination and TiO(2) catalyst, TNT was more effectively degraded than with either UV or TiO(2) alone. The reaction rate was found to obey pseudo first-order kinetics represented by the Langmuir-Hinshelwood model. In the mineralization study, TNT (30 mg/l) photocatalytic degradation resulted in an approximately 80% TOC decrease after 150 min, and 10% of acetate and 57% of formate were produced as the organic intermediates, and were further degraded. NO(-)(3) NO(-)(2), and NH(+)(4) were detected as the nitrogen byproducts from photocatalysis and photolysis, and more than 50% of the total nitrogen was converted mainly to NO(-)(3)in the photocatalysis. However, NO(-)(3) did not adsorbed on the TiO(2) surface. TNT showed higher photocatalytic degradation efficiency at neutral and basic pH.     

Isovaleraldehyde elimination by UV/TiO2 photocatalysis: comparative study of the process at different reactors configurations and scales

A proposal for scaling-up the photocatalytic reactors is described and applied to the coated catalytic walls with a thin layer of titanium dioxide under the near ultraviolet (UV) irradiation. In this context, the photocatalytic degradation of isovaleraldehyde in gas phase is studied. In fact, the removal capacity is compared at different continuous reactors: a photocatalytic cylindrical reactor, planar reactor, and pilot unit. Results show that laboratory results can be useful for reactor design and scale-up. The flowrate increases lead to the removal capacity increases also. For example, with pilot unit, when flowrate extends four times, the degradation rate varies from 0.14 to 0.38 g h^?1 m_cat ^?2. The influence of UV intensity is also studied. When this parameter increases, zboth degradation rate and overall mineralization are enhanced. Moreover, the effects of inlet concentration, flowrate, geometries, and size of reactors on the removal capacity are also studied.     

TiO2光催化氧化降解乳酸的工艺及机理研究

以TiO2为催化剂、紫外灯为光源对乳酸进行光催化降解实验,考察了乳酸初始浓度、TiO2用量、反应时间、曝气方式等因素对乳酸降解率的影响,并在此基础上应用正交实验对降解条件进行优化,同时对乳酸的降解机理进行了探索研究。实验结果表明：以300 W紫外汞灯为光源,在乳酸初始浓度为0.5 g/L、TiO2量为0.20 g/L、反应时间120 min、持续通入空气鼓泡的条件下,乳酸降解效果最佳,乳酸降解率为99.9%;降解12 h总有机碳去除率达91.2%。乳酸光催化降解的反应途径为：乳酸脱羧生成乙醇,乙醇被氧化生成乙醛,进而氧化为乙酸,所有的中间产物被继续降解,最终矿化为CO2和H2O等小分子物质。     

Degradation of calcium lignosulfonate using gamma-ray irradiation

Gamma-ray irradiation was proven to be a promising means for the removal of calcium lignosulfonate (CaLS). At a dose rate of 55Gy min(-1), over 90% of CaLS was mineralized to CO(2), H(2)O and sulfates within 3-d irradiation. The degradation of CaLS with the initial CaLS concentrations ranging from 40 to 200mg l(-1) followed zero-order kinetics at the dose rates of 16-150Gy min(-1). The zero-order degradation rate constant was functionally related with irradiation dose rate. Experiments performed with or without addition of radical scavengers demonstrated that the role of *OH was predominant in CaLS degradation and the reductive species made minor contributions to CaLS degradation. Addition of appropriate amounts of H(2)O(2) significantly enhanced the mineralization of CaLS, e.g., addition of 10mM H(2)O(2) at a dose rate of 55Gy min(-1) elevated the mineralization rate constant by five times. The addition of Fenton's reagent to irradiated CaLS solutions facilitated the degradation of CaLS, but no obviously synergistic effect was observed.     

Selective redox degradation of chlorinated aliphatic compounds by Fenton reaction in pyrite suspension

Selective redox degradation of chlorinated aliphatics by Fenton reaction in pyrite suspension was investigated in a closed system. Carbon tetrachloride (CT) was used as a representative target of perchlorinated alkanes and trichloroethylene (TCE) was used as one of highly chlorinated alkenes. Degradation of CT in Fenton reaction was significantly enhanced by pyrite used as an iron source instead of soluble Fe. Pyrite Fenton showed 93% of CT removal in 140 min, while Fenton reaction with soluble Fe(II) showed 52% and that with Fe(III) 15%. Addition of 2-propanol to the pyrite Fenton system significantly inhibited degradation of TCE (99% to 44% of TCE removal), while degradation of CT was slightly improved by the 2-propanol addition (80-91% of CT removal). The result suggests that, unlike oxidative degradation of TCE by hydroxyl radical in pyrite Fenton system, an oxidation by the hydroxyl radical is not a main degradation mechanism for the degradation of CT in pyrite Fenton system but a reductive dechlorination by superoxide can rather be the one for the CT degradation. The degradation kinetics of CT in the pyrite Fenton system was decelerated (0.13-0.03 min⁻¹), as initial suspension pH decreased from 3 to 2. The formation of superoxide during the CT degradation in the pyrite Fenton system was observed by electron spin resonance spectroscopy. The formation at initial pH 3 was greater than that at initial pH 2, which supported that superoxide was a main reductant for degradation of CT in the pyrite Fenton system.     

Kinetic and chemical assessment of the UV/H2O2 treatment of antiepileptic drug carbamazepine

The UV/H2O2-induced degradation of carbamazepine, a worldwide used antiepileptic drug, recently found as contaminant in many municipal sewage treatment plant (STP) effluents and other aquatic environments, is investigated. The oxidation treatment caused an effective removal of the drug. At complete abatement of the substrate after 4 min treatment, a 35% value of removed total organic carbon (TOC) was obtained. A kinetic constant of (2.05+/-0.14) x 10(9) lmol(-1)s(-1) was determined for OH radical attack to carbamazepine in the UV/H2O2 process. Preparative TLC of the reaction mixture led to the isolation of acridine-9-carboxaldehyde as a reaction intermediate. HPLC and GC/MS analysis indicated formation of small amounts of acridine, salicylic acid, catechol and anthranilic acid among the reaction products. Under the same reaction conditions, synthetically prepared 10,11-epoxycarbamazepine was easily degraded to acridine as main product, suggesting that this epoxide is a likely intermediate in the oxidative conversion of carbamazepine to acridine. Under sunlight irradiation, carbamazepine in water underwent slow degradation to afford likewise acridine as main product. In view of the mutagenic properties of acridine, these results would raise important issues concerning the possible environmental impact of carbamazepine release through domestic wastewaters and support the importance of prolonged oxidation treatments to ensure complete degradation of aromatic intermediates.