Short-term temporal variation in PM2.5 mass and chemical composition during the Atlanta Supersite Experiment, 1999

Measurements in urban Atlanta of transient aerosol events in which PM2.5 mass concentrations rapidly rise and fall over a period of 3-6 hr are reported. The data are based on new measurement techniques demonstrated at the U.S. Environmental Protection Agency (EPA) Atlanta Supersite Experiment in August 1999. These independent instruments for aerosol chemical speciation of NO3-, SO4(2-), NH4+, and organic and elemental carbon (OC and EC), reconstructed the observed hourly dry PM2.5 mass to within 20% or better. Data from the experiment indicated that transient PM2.5 events were ubiquitous in Atlanta and were typically characterized by a sudden increase of EC (soot) and OC in the early morning or SO4(2-) in the late afternoon. The frequent temporal decoupling of these events provides insights into their origins, suggesting mobile sources in metro Atlanta as the main contributor to early morning PM2.5 and more regionally located point SO2 sources for afternoon PM2.5 events. The transient events may also have health implications. New data suggest that short-term PM2.5 exposures may lead to adverse health effects. Standard integrated filter-based techniques used in PM2.5 compliance monitoring networks and in most past PM2.5 epidemiologic studies collect samples over 24-hr periods and thus are unable to capture these transient events. Moreover, health-effects studies that focus on daily PM2.5 mass alone cannot evaluate the health implications of the unique and variable chemical properties of these episodes.     

Photochemistry in the mixed aqueous solution of nitrobenzene and nitrous acid as initiated by the 355 nm UV light

The 355 nm photon-initiated microscopic reaction mechanisms of the mixed aqueous solution of nitrobenzene and nitrous acid in the presence or absence of O(2) were studied by the laser flash photolysis technique. The main transient absorption peaks in the recorded spectra were assigned and the growth/decay trends of several transient species were investigated. It was found that the OH radical formed from the photolysis of nitrous acid triggered most of the subsequent radical reactions. The rate constant of the reaction between OH radical and nitrobenzene was measured to be (3.4 +/- 0.1) x 10(9) l mol(-1) s(-1). The product from this reaction, namely C(6)H(5)NO(2)-OH adduct, was found to react with O(2) to yield C(6)H(5)NO(2)-OHO(2) adduct with a rate constant of (1.6 +/- 0.2) x 10(9) l mol(-1) s(-1). Final steady-state products were identified by GC/MS analysis and were in accordance with the transient spectroscopic results. The possible reaction pathways were proposed.     

Investigation of surfactant-enhanced dissolution of entrapped nonaqueous phase liquid chemicals in a two-dimensional groundwater flow field.

Because of their low solubility, waste chemicals in the form of nonaqueous phase liquids (NAPLs) that are entrapped in subsurface formations act as long-term sources of groundwater contamination. In the design of remediation schemes that use surfactants, it is necessary to estimate the mass transfer rate coefficients under multi-dimensional flow fields that exit at field sites. In this study, we investigate mass transfer under a two-dimensional flow field to obtain an understanding of the basic mechanisms of surfactant-enhanced dissolution and to quantify the mass transfer rates. Enhanced dissolution experiments in a two-dimensional test cell were conducted to measure rates of mass depletion from entrapped NAPLs to a flowing aqueous phase containing a surfactant. In situ measurement of transient saturation changes using a gamma attenuation system revealed dissolution patterns that are affected by the dimensionality of the groundwater flow field. Numerical modeling of local flow fields that changed with time, due to depletion of NAPL sources, enabled the examination of the basic mechanisms of NAPL dissolution in complex groundwater systems. Through nonlinear regression analysis, mass transfer rates were correlated to porous media properties, NAPL saturation and aqueous phase velocity. Results from the experiments and numerical analyses were used to identify deficiencies in existing methods of analysis that uses assumptions of one-dimensional flow, homogeneity of aquifer properties, local equilibrium and idealized transient mass transfer.     

Two dechlorinated chlordecone derivatives formed by in situ chemical reduction are devoid of genotoxicity and mutagenicity and have lower proangiogenic properties compared to the parent compound

Chlordecone (CLD) is a chlorinated hydrocarbon insecticide, now classified as a persistent organic pollutant. Several studies have previously reported that chronic exposure to CLD leads to hepatotoxicity, neurotoxicity, raises early child development and pregnancy complications, and increases the risk of liver and prostate cancer. In situ chemical reduction (ISCR) has been identified as a possible way for the remediation of soils contaminated by CLD. In the present study, the objectives were (i) to evaluate the genotoxicity and the mutagenicity of two CLD metabolites formed by ISCR, CLD-5a-hydro, or CLD-5-hydro (5a- or 5- according to CAS nomenclature; CLD-1Cl) and tri-hydroCLD (CLD-3Cl), and (ii) to explore the angiogenic properties of these molecules. Mutagenicity and genotoxicity were investigated using the Ames’s technique on Salmonella typhimurium and the in vitro micronucleus micromethod with TK6 human lymphoblastoid cells. The proangiogenic properties were evaluated on the in vitro capillary network formation of human primary endothelial cells. Like CLD, the dechlorinated derivatives of CLD studied were devoid of genotoxic and mutagenic activity. In the assay targeting angiogenic properties, significantly lower microvessel lengths formed by endothelial cells were observed for the CLD-3Cl-treated cells compared to the CLD-treated cells for two of the three tested concentrations. These results suggest that dechlorinated CLD derivatives are devoid of mutagenicity and genotoxicity and have lower proangiogenic properties than CLD.     

Fate of PBDEs during food processing: Assessment of formation of mixed chlorinated/brominated diphenyl ethers and brominated dioxins/furans

The aim of this study was to evaluate effects of food processing on PBDE levels, in particular influence of heat treatment on degradation of PBDEs, including possible formation of chlorinated diphenyl ethers or brominated dioxins/furans as degradation products. It was shown that PBDEs heated in the presence of chlorine (from either organic or inorganic sources) formed mixed chlorinated/brominated diphenyl ethers. However, no PCDEs were formed in the presence of lipids. Lipid medium increased stability of PBDEs exposed to UV irradiation. Profile of congeners formed in result of the debromination reaction was significantly different than profiles observed by some other authors in aliphatic organic solvents. Grilling processes increased concentrations (calculated on the fresh product basis) of the studied compounds by 4–8/22–34% for electric/coal grill, respectively. Depending on the congener and on the applied heat treatment, PBDE mass in pork meat after grilling dropped by 26–53%. No detectable quantities of either brominated dioxins or furans were formed during thermal processing of food containing typical levels of PBDEs.     

Source apportionment of particulate matter in a large city of southeastern Po Valley (Bologna, Italy)

This study reports the results of an experimental research project carried out in Bologna, a midsize town in central Po valley, with the aim at characterizing local aerosol chemistry and tracking the main source emissions of airborne particulate matter. Chemical speciation based upon ions, trace elements, and carbonaceous matter is discussed on the basis of seasonal variation and enrichment factors. For the first time, source apportionment was achieved at this location using two widely used receptor models (principal component analysis/multi-linear regression analysis (PCA/MLRA) and positive matrix factorization (PMF)). Four main aerosol sources were identified by PCA/MLRA and interpreted as: resuspended particulate and a pseudo-marine factor (winter street management), both related to the coarse fraction, plus mixed combustions and secondary aerosol largely associated to traffic and long-lived species typical of the fine fraction. The PMF model resolved six main aerosol sources, interpreted as: mineral dust, road dust, traffic, secondary aerosol, biomass burning and again a pseudo-marine factor. Source apportionment results from both models are in good agreement providing a 30 and a 33 % by weight respectively for PCA-MLRA and PMF for the coarse fraction and 70 % (PCA-MLRA) and 67 % (PMF) for the fine fraction. The episodic influence of Saharan dust transport on PM₁₀ exceedances in Bologna was identified and discussed in term of meteorological framework, composition, and quantitative contribution.     

Transient‐phase and steady‐state kinetics of lipase‐catalyzed ester hydrolysis 1

Abstract

An experimental study has been made of both the steady‐state and the transient‐phase (presteady‐state) kinetics of the hydrolyses of several saturated aliphatic esters of p‐nitrophenol catalyzed by wheat germ lipase. The analysis of the presteady‐state part revealed two transients indicating that lipase‐catalyzed reactions proceed via a two‐intermediate mechanism suggested for other esterases. The possibility of more than one species of the enzyme engaged in catalytic activity is discussed and a reaction mechanism scheme is proposed accordingly.     

Tracking Regional Background in a Haze Attribution Experiment

ABSTRACT

Emissions from distant source areas are often imagined to provide a steady background to the emissions of whatever local sources are being studied. As part of Project MOHAVE in summer 1992, several air mass markers and an injected stack tracer were measured hourly near the Grand Canyon. Observed haze events generally coincided with transients in methylchloroform and water vapor, which we interpret as endemic tags for air from southern California and the subtropics. The results depict a dynamic regional background.     

Open-path tunable diode laser absorption spectroscopy for acquisition of fugitive emission flux data

Air pollutant emission from unconfined sources is an increasingly important environmental issue. The U.S. Environmental Protection Agency (EPA) has developed a ground-based optical remote-sensing method that enables direct measurement of fugitive emission flux from large area sources. Open-path Fourier transform infrared spectroscopy (OP-FTIR) has been the primary technique for acquisition of pollutant concentration data used in this emission measurement method. For a number of environmentally important compounds, such as ammonia and methane, open-path tunable diode laser absorption spectroscopy (OP-TDLAS) is shown to be a viable alternative to Fourier transform spectroscopy for pollutant concentration measurements. Near-IR diode laser spectroscopy systems offer significant operational and cost advantages over Fourier transform instruments enabling more efficient implementation of the measurement strategy. This article reviews the EPA's fugitive emission measurement method and describes its multipath tunable diode laser instrument. Validation testing of the system is discussed. OP-TDLAS versus OP-FTIR correlation testing results for ammonia (R2 = 0.980) and methane (R2 = 0.991) are reported. Two example applications of tunable diode laser-based fugitive emission measurements are presented.     

Seasonal and shorter-term variations in particulate atmospheric nitrate in Baltimore

Fine particle nitrate concentrations were measured at 10-min intervals for approximately 9.5 months beginning on 14 February 2002, at the Baltimore Supersite Ponca St. location using an R&P 8400N semi-continuous monitor. The measurement results were used to characterize seasonal and shorter-term excursions in nitrate concentrations and determine their influence on PM_2.5 concentrations. Over the 9.5-month study period, nitrate levels of 1.7±1.6 μg m⁻³ accounted for 11.4% of the PM_2.5 mass. Monthly averages ranged from 0.8 μg m⁻³ in August to 2.9 μg m⁻³ in November, and accounted for 4.7–17.3% of monthly PM_2.5 mass. Hourly averages, however, were often larger, especially in the colder months, owing to numerous relatively short-term transients, where hourly nitrate concentrations exceeded 5.0 μg m⁻³. These often occurred along with NO_x and ultrafine particle transients during the morning commute hours.A total of 275 short-term transients (31.7% of the total) exceeding 1.0 μg m⁻³ were identified. These were associated with one of three sets of conditions. The first, most typical (177, i.e. 64.4% of the 275 incidences), is characterized by high NO_x typically between 0500 and 0800EST and is attributed to early morning commute traffic activity. The second type occurred during the afternoon due to photochemical activity. The excursions in the afternoon occurred infrequently (only 9.5% of all the observed transients) during the study period and were characterized by less elevated nitrate concentrations than morning and nighttime transients. The third (72, i.e. 26.2% of the 275 transients) occurred at night, typically between 2000EST and 0200EST.Multiple linear regression analysis between nitrate excursions and volume size distributions indicates that particulate nitrate observed is closely related to the near accumulation (0.1–0.2 μm) and droplet modes (0.5–1.0 μm) in the morning hours, and associated with the droplet (0.5–1.0 μm) and coarse modes (1.0–2.5 μm) for nighttime transients, suggesting that processes governing particulate nitrate formation depend on time-of-day.     

Characteristics of aerosol types from AERONET sunphotometer measurements

By using observations from the Aerosol Robotic Network (AERONET), aerosol types are classified according to dominant size mode and radiation absorptivity as determined by fine-mode fraction (FMF) and single-scattering albedo (SSA), respectively. The aerosol type from anthropogenic sources is significantly different with regard to location and season, while dust aerosol is observed persistently over North Africa and the Arabian Peninsula. For four reference locations where different aerosol types are observed, time series and optical properties for each aerosol type are investigated. The results show that aerosol types are strongly affected by their sources and partly affected by relative humidity. The analysis and methodology of this study can be used to compare aerosol classification results from satellite and chemical transport models, as well as to analyze aerosol characteristics on a global scale over land for which satellite observations need to be improved.     

Multiple effects of chromate on the photosynthetic apparatus of Spirodela polyrhiza as probed by OJIP chlorophyll a fluorescence measurements

Chromate (Cr) decreases the growth of Spirodela polyrhiza. The fronds lost their pigments. The O2 evolution was also decreased. The Cr effect was found to be dose dependent. The toxic effects of Cr have further been studied on the photosynthetic activity of Spirodela polyrhiza by means of the chlorophyll a (Chl a) fluorescence transient O-J-I-P. The Chl a fluorescence transients were recorded in vivo with high time resolution and analyzed according to the JIP-test which can quantify the photosystem II behavior. Cr treated plants show a decrease in yield for primary photochemistry, phi Po. The performance index of PSII, PIABS, which is the combination of the indexes of three independent parameters, (1) the total number of active reaction centers per absorption (RC/ABS), (2) yield of primary photochemistry (phi Po) and (3) efficiency with which a trapped exciton can move an electron into the electron transport chain (psi 0), decreased due to Cr treatment. Chromate sensitivity varies within plant populations. In summary Cr affects several targets of PSII. More specifically, the main targets of Cr, according to the JIP-test, can be listed as a decrease in the number of active reaction centers and damage to the oxygen-evolving complex.     

On-line real-time measurements at incineration plants: PAHs and a PCDD/F surrogate compound at stationary combustion conditions and during transient emission puffs

Laser mass spectrometry has been applied for on-line monitoring of traces of aromatic compounds from flue gas of incineration plants. The experiments have been carried out at two sampling sites in an industrial hazardous-waste incinerator. With laser mass spectrometry resonance-enhanced multiphoton ionization (REMPI) with time-of-flight mass spectrometry (TOFMS) (REMPI-TOFMS), using the group selective multi-component monitoring approach, aromatic compounds are selectively ionized from the complex flue-gas matrix. In this case, the result of an REMPI-TOFMS on-line measurement is a distinct pattern of aromatic compounds. These patterns are dependent on: (i) the point of measurement, (ii) the incineration plant, (iii) the temperature, and (iv) the fuel. This contribution focuses on the fuel dependence of the pattern. The most transient behavior can be observed when containers filled with hazardous waste are burnt, leading to puffs. Real-time monitoring results of puffs are given. Furthermore, as an approach towards on-line monitoring of the TEQ (PCDD/F toxicity equivalent), REMPI-TOFMS on-line analysis results of chlorobenzene are presented.     

The seasonal cycles and photochemistry of C2–C5 alkanes at Mace Head

Continuous in-situ measurements of NMHCs at Mace Head, Ireland during two full annual cycles from January 2005 to January 2007 were used to investigate NMHC emission sources and transport including dilution and photochemical oxidation. The Mace Head research station is ideally located to sample a wide range of air masses including polluted European transport, clean North Atlantic and Arctic air masses and the ultra-clean, Southern Atlantic air masses. The variety in air mass sampling is used to investigate interaction of emissions, transport, dilution and photochemistry. Variability of long-lived hydrocarbon ratios is used to assess and estimate typical transport times from emission source to the Mace Head receptor. Seasonality in the ratios of isomeric alkane pairs (for butane and pentanes) are used to assess the effects of atmospheric transport and photochemical ageing. Finally, the natural logarithms of NMHC ratios are used to assess photochemical oxidation.     

Cloud Albedo,Greenhouse Effects,Atmospheric Chemistry,and Climate Change

Changes in global atmospheric chemistry and climate are taking place as a result of observed trends in long-lived species such as CO₂, CH₄, N₂O, and the CFCs. The continuation of these trends is expected to eventually lead to a major atmospheric warming that might profoundly affect the society we live in. Trends in short-lived species such as NOx and SOx are also suspected. These trends are not as well established, because the shorter-lived species vary spatially and temporally. Trends in NOx would be expected to lead to increases in tropospheric ozone that would add to the warming created by the other greenhouse gases. Trends in NOx could also alter tropospheric OH concentrations that could lead to changes in CH₄ and some of the CFCs. On the other hand, increases in sulfur emissions may alter cloud optical properties. The changes in cloud optical properties could possibly offset the warming expected from increases in greenhouse gases, depending on the role of natural oceanic sulfur emissions. This paper summarizes recent research in these areas and the interactions of climate and atmospheric chemistry.     

Cadmium and methylmercury bioaccumulation by nymphs of the burrowing mayflyHexagenia rigida from the water column and sediment

Based on a three compartment microcosm-water column, natural sediment,Hexagenia rigida nymphs-an experimental study was set up to compare cadmium (Cd) and methylmercury (MeHg) bioaccumulation by a burrowing mayfly species, after exposure via the water column or the sediment as initial contamination sources. Results from a wide concentration range for each exposure condition revealed very marked differences between the two metals: MeHg was readily accumulated from the two contamination sources, leading to important metal concentrations in the nymphs after the 2 weeks’ exposure; Cd bioaccumulation, on the other hand, was negligible when the metal was added to the water compartment, even though significant transfers were observed from the sediment source. The average Cd concentrations in the nymphs were proportional to the sediment contamination levels. Turbidity measurements in the water column, reflecting the bioturbation activity of the nymphs, revealed that the effect of Cd was significant, but only when the metal was initially added to the sediment. The results are discussed according to the uptake routes and the structural and functional properties of the biological barriers involved (gills and gut).     

Characterization of atmospheric dry deposition particulates in Kobe, Japan

The sources and character of individual metal and metalloid particles from atmospheric dry depositions in Kobe, Japan were investigated. Japan faces long-range pollutant transportation from northeastern Asia during winter and spring. Information regarding their properties and sources is useful for evaluating their affects on the environment and human health. Individual metal and metalloid particles that were collected for every 24 h on the plate, which was designed to reduce a local turbulence, were characterized for their composition, diameter, and deposition fluxes using a field emission scanning electron microscope with an energy dispersive X-ray spectrometer. Approximately 3,000 metal and metalloid particles were classified into 14 types based on their composition and further classified into four groups based on their distribution patterns. They are (A) Fe-O, Fe-Ba-Sb-Cu-S-Ti-O, Fe-Zn-O, Zn-O, Ni-O, and Mn-Fe-O; (B) Cu-Zn-O and Cu-Sn-O; (C) Pb-O, Sn-Sb-O, and Ag-O; (D) Pb-Zn-Cl-Si-S-O and Bi-Cl-O. From these data, this study suggests their sources as the Asian continent (Group A), local source (Group B), multiple sources (Group C), and incineration process (Group D). This study shows (1) the sources and character of individual metal and metalloid particles from short-term atmospheric depositions in Kobe, Japan and (2) application of individual particle analysis for atmospheric depositions.     

Aerosol laser ablation mass spectrometry of suspended powders from PM sources and its implications to receptor modeling

Primary sources of particulate matter (PM) were analyzed by suspending powdered samples into an aerosol laser ablation mass spectrometer (LAMS). PM sources studied included vehicle exhaust particulates, dust from a non-ferrous smelter, cement powder, incinerator fly ash, two coal fly ash samples, and two soils. Marker peaks signified certain PM source sectors: construction particles could be distinguished by abundant Ca and Ca compounds, fuel combustion was marked by elemental carbon clusters, and nonferrous industrial particles showed inorganic As, Cu, Pb, Zn, and SOx. In addition to the distinction between particles from these different source sectors, mass spectral results also showed that for a single source, different particle types existed, and among different sources within a sector, similar spectra were present. The aerosol LAMS results show the difficulty in differentiating among separate fly ash sources as well as among different soil samples. A particle class balance receptor model that measures the amount of specific particle types rather than the amount of a chemical component is suggested as a means of source apportionment when particle spectra with overlapping source possibilities occur. The assumptions and limitations of receptor modeling aerosol LAMS data are also described. In particular, methods need to be developed to account for the contribution of secondary sources.     

Analysis of a mesoscale infiltration and water seepage test in unsaturated fractured rock: Spatial variabilities and discrete fracture patterns

A mesoscale (21 m in flow distance) infiltration and seepage test was recently conducted in a deep, unsaturated fractured rock system at the crossover point of two underground tunnels. Water was released from a 3 mx4 m infiltration plot on the floor of an alcove in the upper tunnel, and seepage was collected from the ceiling of a niche in the lower tunnel. Significant temporal and (particularly) spatial variabilities were observed in both measured infiltration and seepage rates. To analyze the test results, a three-dimensional unsaturated flow model was used. A column-based scheme was developed to capture heterogeneous hydraulic properties reflected by these spatial variabilities observed. Fracture permeability and van Genuchten alpha parameter [van Genuchten, M.T., 1980. A closed-form equation for predicting the hydraulic conductivity of unsaturated soils. Soil Sci. Soc. Am. J. 44, 892-898] were calibrated for each rock column in the upper and lower hydrogeologic units in the test bed. The calibrated fracture properties for the infiltration and seepage zone enabled a good match between simulated and measured (spatially varying) seepage rates. The numerical model was also able to capture the general trend of the highly transient seepage processes through a discrete fracture network. The calibrated properties and measured infiltration/seepage rates were further compared with mapped discrete fracture patterns at the top and bottom boundaries. The measured infiltration rates and calibrated fracture permeability of the upper unit were found to be partially controlled by the fracture patterns on the infiltration plot (as indicated by their positive correlations with fracture density). However, no correlation could be established between measured seepage rates and density of fractures mapped on the niche ceiling. This lack of correlation indicates the complexity of (preferential) unsaturated flow within the discrete fracture network. This also indicates that continuum-based modeling of unsaturated flow in fractured rock at mesoscale or a larger scale is not necessarily conditional explicitly on discrete fracture patterns.