A new approach to characterize emission contributions from area sources during optical remote sensing technique testing

In the method termed “Other Test Method-10,” the U.S. Environmental Protection Agency has proposed a method to quantify emissions from nonpoint sources by the use of vertical radial plume mapping (VRPM) technique. The surface area of the emitting source and the degree to which the different zones of the emitting source are contributing to the VRPM computed emissions are often unknown. The objective of this study was to investigate and present an approach to quantify the unknown emitting surface area that is contributing to VRPM measured emissions. Currently a preexisting model known as the “multiple linear regression model,” which is described in Thoma et al. (2009 Thoma, E.R., Green, R., Hater, G., Goldsmith, C., Swan, N., Chase, M. and Hashmonay, R. 2010. Development of EPA OTM-10 for landfill applications. J. Environ. Eng., 136: 769–776. [Crossref], [Web of Science ®] , [Google Scholar]), is used for quantifying the unknown surface area.

The method investigated and presented in this paper utilized tracer tests to collect data and develop a model much like that described in Thoma et al. (2009 Thoma, E.R., Green, R., Hater, G., Goldsmith, C., Swan, N., Chase, M. and Hashmonay, R. 2010. Development of EPA OTM-10 for landfill applications. J. Environ. Eng., 136: 769–776. [Crossref], [Web of Science ®] , [Google Scholar]). However, unlike the study used for development of the multiple linear regression model, this study is considered a very limited study due to the low number of pollutant releases performed (seven total releases). It was found through this limited study that the location of an emitting source impacts VRPM computed emissions exponentially, rather than linearly (i.e., the impact that an emitting source has on VRPM measurements decreases exponentially with increasing distances between the emitting source and the VRPM plane). The data from the field tracer tests were used to suggest a multiple exponential regression model. The findings of this study, however, are based on a very small number of tracer tests. More tracer tests performed during all types of climatic conditions, terrain conditions, and different emissions geometries are still needed to better understand the variation of capture efficiency with emitting source location. This study provides a step toward such an objective.

Implications The findings of this study will aid in the advancement of the VRPM technique. In particular, the contribution of this study is to propose a slight improvement in how the area contributing to flux is determined during VRPM campaigns. This will reduce some of the technique's inherent uncertainties when it is employed to estimate emissions from an area source under nonideal conditions.     

Fine Particle Removal Performance of a Two-Stage Wet Electrostatic Precipitator Using a Nonmetallic Pre-Charger

ABSTRACT

A novel two-stage wet electrostatic precipitator (ESP) has been developed using a carbon brush pre-charger and collection plates with a thin water film. The electrical and particle collection performance was evaluated for submicrometer particles smaller than 0.01～0.5 μm in diameter by varying the voltages applied to the pre-charger and collection plates as well as the polarity of the voltage. The collection efficiency was compared with that calculated by the theoretical models. The long-term performances of the ESP with and without water films were also compared in tests using Japanese Industrial Standards dust. The experimental results show that the carbon brush pre-charger of the two-stage wet ESP had approximately 10% particle capture, while producing ozone concentrations of less than 30 ppb. The produced amounts of ozone are significantly lower than the current limits set by international agencies. The ESP also achieved a high collection rate performance, averaging 90% for ultrafine particles, as based on the particle number concentration at an average velocity of 1 m/sec corresponding to a residence time of 0.17 sec. Higher particle collection efficiency for the ESP can be achieved by increasing the voltages applied to the pre-charger and the collection plates. The decreased collection efficiency that occurred during dust loading without water films was completely avoided by forming a thin water film on the collection plates at a water flow rate of 6.5 L/min/m2 Zukeran, A., Ikeda, Y., Ehara, Y., Matsuyama, M., Ito, T., Takahashi, T., Kawakami, H. and Takamatsu, T. 1999. Two-Stage-Type Electrostatic Precipitator Re-entrainment Phenomena under Diesel Flue Gases. IEEE. Trans. Ind. Appl, 35: 346–351. [Crossref], [Web of Science ®] , [Google Scholar].

IMPLICATIONS Current two-stage electrostatic precipitators (ESPs) have several technical problems such as a drop in collection efficiencies by small-particle re-entrainment during rapping and corrosion of metallic electrodes of the ESPs by corrosive gases. This paper evaluates a novel two-stage ESP that uses a nonmetallic pre-charger and water film collection plates to avoid the above mentioned problems of other ESPs. This ESP can be used not only for industrial applications but also for residential purposes because it has a high removal performance for fine particles with low ozone generation and maintains its efficiency due to the continuous cleaning of the collection plates with water film.     

Behavioural ecotoxicology,an “early warning” signal to assess environmental quality

Background

In this review, the position of behavioural ecotoxicology within the available means to assess the status of marine environments is described as filling the gap for the needed “early warning” signals. A few examples of studies performed since the 1960s are discussed to highlight the sensitivity of these approaches in investigating the effects of chemicals, including priority pollutants and emerging contaminants, relative to conventional toxicity tests measuring survival.

Discussion

The advantage of the behavioural response is due to the integration of biochemical and physiological processes that reflect changes at higher levels of organisation with ecological relevance. Avoidance often represents a behavioural symptom easily detected in many animals exposed to contaminants and would be a useful test to explore more widely. This rapid response would reflect a defence mechanism protective against further exposure and the potential development of more pronounced deleterious effects, whilst in some cases, escape could lead to the relocation of a species with negative consequences. An investigation of the avoidance behaviour of mud shrimp, Corophium volutator, along with the chemical analyses of sediments and amphipods to assess the quality of harbour sediments is summarised. The body burden of the amphipods was 1,000 times lower than the one associated with narcosis, emphasizing the sensitivity of this endpoint. The application of this acute toxicity test is briefly compared to additional work that involved intertidal mussels collected in the field.

Conclusions

Recent research undertaken with mud snails, Ilyanassa obsoleta, and harbour sediments confirmed the usefulness of the escape behaviour as an assessment tool. However, the limits of the state of knowledge regarding the fate of contaminants in species with the ability to metabolise contaminants is further discussed along with directions to be pursued to address questions arising from the reviewed literature.

     

An assessment of the potential toxicity of runoff from an urban roadscape during rain events

Goal, Scope and Background

The potential negative impact of urban storm water on aquatic freshwater ecosystems has been demonstrated in various studies with different types of biological methods. There are a number of factors that influence the amount and bioavailability of contaminants in storm water even if it is derived from an area with a fairly homogenous land use such as a roadscape where a variation in toxicity during rain events might be expected. There are only a few previous investigations on the toxicity of highway runoff and they have not explored these issues extensively. The main objective of this study is therefore to characterize the potential toxicity of highway runoff during several rain events before it enters a detention pond in VästerOas, Sweden, using laboratory bioassays with test organisms representing various functional groups in an aquatic ecosystem. The results are to be used for developing a monitoring program, including biological methods.

Materials and Methods

The storm water was sampled before the entrance to a detention pond, which receives run-off from a highway with approximately 20,000 vehicles a day. The drainage area, including the roadscape and vegetated areas, is 4.3 ha in size. Samples for toxicity tests were taken with an automatic sampler or manually during storm events. In total, the potential toxicity of 65 samples representing 15 different storm events was determined. The toxicity was assessed with 4 different test organisms; Vibrio fischeri using the Microtox® comparison test, Daphnia magna using Daphtoxkit-F?agna, Thamnocephalus platyurus using the ThamnotoxkitF? and Lemna minor, duckweed using SS 028313.

Results and Discussion

Of the 65 samples, 58 samples were tested with DaphniatoxkitF?agna, 57 samples with the Microtox® comparison test, 48 samples with ThamnotoxkitF? and 20 samples with Lemna minor, duckweed. None of the storm water samples were toxic.No toxicity was detected with the Lemna minor test, but in 5 of the 23 samples tested in comparison to the control a growth stimulation of 22–46% was observed. This is in accordance with the chemical analysis of the storm water, which indicated rather large concentrations of tot-N and tot-P. In addition to the growth stimulation, morphological changes were observed in all the 5 samples from the winter event that was sampled. The lack of toxicity observed in our study might be due to a lower traffic intensity (20,000 vehicles/day) at the site and the trapping of pollutants in the vegetated areas of the roadscape, resulting in much smaller loads of pollutants in the storm water than in some previous studies.

Conclusions

Ecotoxicological evaluations of storm water including run off from rain events from urban roadscape studies clearly reveal that toxicity may or may not be detected depending upon site, storm condition and the test organism chosen. However, storm water might not be as polluted as previously reported nor may the first flush be such a widespread phenomenon as we originally expected. In this study, there was also a good correlation between pollutant load measured and the lack of toxicity. The test organisms chosen in this study are commonly used in effluent control programs in Sweden and other countries, which makes it possible to compare the results with those from other effluents. In this study, only acute toxicity tests were used and further studies using chronic toxicity tests, assays for genotoxic compounds or in situ bioassays might reveal biological effects at this site. Furthermore, most of the samples were taken in spring, summer or fall and it is possible that winter conditions might alter the constituents in the storm water and, thus, the toxicity of the samples.

Recommendations and Perspectives

Considering the complex nature of run off from urban roadscapes, it will be virtually impossible to evaluate properly the potential hazard of particular storm water and the efficiency of a particular treatment strategy from only physical and chemical characterizations of the effluent. Therefore, despite the lack of toxicity detected in this study, it is recommended that toxicity tests or other biological methods should be included in evaluations of the effects of runoff from roadscapes.

     

Sorption of polycyclic aromatic hydrocarbons (PAHs) to low and high density polyethylene (PE)

Background, aim, and scope

According to their high sorption capacity polyethylene (PE) passive samplers are often used for the analysis of polycyclic aromatic hydrocarbons (PAHs) in the aquatic environment. PE is also one of the primary synthetic polymers found in oceans, and sorption of PAHs to marine PE debris may determine PAH exposure and therefore hazards in marine ecosystems. Thus, an understanding of the sorption process is of great importance. In the present study, the sorption of several PAHs with different polarities to low density polyethylene (LDPE) and high density polyethylene (HDPE) was studied in order to improve our understanding of the influence of material properties on the Fickian diffusion of PAHs into PE.

Materials and methods

Batch sorption experiments were performed with aqueous solutions containing acenaphthylene, acenaphthene, fluorene, phenanthrene, anthracene, fluoranthene, and LPDE or HDPE pellets. Samples were shaken in the dark at 20?±?1°C for 16 time intervals within one week. Concentrations of PAHs were determined in the aqueous samples using solid-phase microextraction coupled with gas chromatography–mass spectrometry. The distribution coefficients (K _PE) between PE and water were estimated from different models reported in the literature. Kinetic sorption of the PAHs into the plastic pellets was described by a diffusion model based on Fick’s second law in spherical coordinates.

Results and discussion

A comparison between different models describing the equilibrium distribution of PAHs between PE and water revealed that the sorption equilibrium seemed to be driven by parameters other than, or in addition to, organic carbon. For both plastic types, diffusion coefficients decreased while the molecular weight of the PAHs increased which indicates a hindered diffusion through the matrix as a result of a larger molecule size. Higher diffusion coefficients were derived for LPDE than for HDPE indicating a greater sorption velocity for LPDE according to the lower polymer density.

Conclusions

Our results revealed that equilibrium time could be shortened during passive sampling as polymer membranes of lower density are used. In some areas, marine ecosystems may not be in equilibrium with respect to concentrations of organic contaminants and abundance of marine plastic debris. In such cases, different polymer densities should be taken into account in risk assessments.

     

Metals and PCB levels in some edible marine organisms from the Ionian Sea: dietary intake evaluation and risk for consumers

Concentrations of some metals (Cd, Cu, As, Hg, Pb) and polychlorinated biphenyls (PCBs) were investigated in edible marine organisms from different trophic levels and feeding behaviour like bivalve molluscs (Mytilus galloprovincialis and Chlamys glabra), gastropod molluscs (Hexaplex trunculus) and some commercial species of fish (Trachurus trachurus, Boops boops, Sarpa salpa and Gobius niger). These species were collected in the first inlet of the Mar Piccolo of Taranto (Ionian Sea, Southern Italy), classified as ‘Site of National Interest’ established by National Law 426 (1998) and included in the ‘National Environmental Remediation and Restoration Projects’. The aim of this work was to investigate contamination levels and public health risks, associated with consuming seafood harvested from these areas. Moreover, in this study, was also estimated the weekly intake in children and adults, both for metals and PCBs. In comparison with the permissible limits set by EC Regulations, Cd and Pb levels were over the limit in the H. trunculus (in all sampling stations) and in the fish T. trachurus respectively. PCBs were over the legal limit in all sampled species with the exception of M. galloprovincialis (station 1), C. glabra and the herbivorous fish S. salpa. In the fish T. trachurus, for example, the concentration of six target PCBs was about five times higher than the EC limit. The estimated intakes of those trace elements included in this study through seafood consumption by the population exceed the provisional tolerable weekly intake recommended by the Joint FAO/WHO Expert Committee on Food Additives for Cd and Hg in the H. trunculus and T. trachurus, especially in children. Moreover, hazard quotience (HQ) for Hg and Cd was >1 in the children for T. trachurus and H. trunculus consumption. As regard non-dioxin-like PCB (NDL-PCB), the estimated intake were always above the ‘provisional guidance value’ (70 ng/kg body weight) Arnich et al. (Regul Toxicol Pharm 54: 287–2, 2009) for all sampled organism. Thus, health risks due to the dietary Hg, Cd and PCBs intake, especially for children, cannot be excluded. Therefore, an extended remediation programme is necessary to safeguard marine ecosystem, human health and, not less important, the economic activities, in the Taranto marine area.     

Toxicity testing of highly volatile chemicals with green algae

A gas-tight system for toxicity testing of highly volatile chemicals with the green algaChlamydomonas reinhardtii was developed. The procedure permits maintenance of constant and defined concentrations of the tested compounds in the vessels. To ensure sufficient CO₂-supply, new bipartite test vessels were used. These vessels allowed spatial separation of a HCO₃-/CO ₃ ^2? buffer used for CO₂ supply and the alga culture to avoid growth inhibition due to ionic strength. Several volatile chlorinated hydrocarbons have been tested. Their EC10 values were several orders of magnitude lower than those obtained with open test systems.     

Contaminants of food

A scheme has been developed to rank 70 industrial organic chemicals in order of their priority for further study as potential contaminants of food. Numerical scales were developed for the following seven key criteria concerning environmental issues, food and toxicity:

-Production volume

-Pattern of usage

-Possible fate in the environment

-Likelihood of chemical entering the food chain

-Mechanism of entry into the food chain

-Persistence and accumulation in the food chain

-Toxicity.

Each chemical was assigned a score for the above criteria, which were combined to give an overall ranking for the chemicals. This scheme has been endorsed by the MAFF Steering Group on Chemical Aspects of Food Surveillance. It will be used in the assessment of relative priorities for further non-statutory surveillance for these contaminants in the UK food supply.     

Influence of sediment acidification on the bioaccumulation of metals in Ruditapes philippinarum

Background, aim and scope

The influence of pH (range 6.5–8.5) on the uptake of Zn, Cd, Pb, Cu, Ni, Cr, Hg, and As by juveniles of the clam Ruditapes philippinarum was examined in order to understand whether variation in sediment pH has significant repercussions on metal bioaccumulation.

Materials and methods

Clams were exposed to sediments collected in three locations in the Gulf of Cadiz (Huelva, Guadalquivir and Bay of Cadiz) and to contaminated particles derived from an accidental mining spill in Spain.

Results

With a notable exception of metal Cd, the concentration of metals within clams significantly increased (p?<?0.1) when sediment pH was lowered by one or two units. Moreover, the magnitude of this effect was dependent on the type of sediment contamination.

Discussion

Lower pH increases metal solubility and reduces or invert the metal sorption of metals to sediments. Increases in free metal ions in water favors metal uptake by clams, hence pH is an important factor controlling the mobility of these metals within sediments and their subsequent bioaccumulation within biota. Although sediment-water exchange of Cd can increase with acidification, this excess may be counterbalanced by the presence of ligands in seawater preventing the uptake by organism. Besides chlorines, Cd has also an affinity with carbonates and other ligands present in sea water. These Cd-carbonate complexes may reduce the bioavailable to organisms.

Conclusions

These results highlight the potential implications of sediment acidification, either due to the storage excess of organic matter or to the forced capture of CO₂, on the increasing metal availability to benthic organisms.

Recommendations and perspectives

This kind of studies should be increased to address the influence of acidification in the behavior, bioavailability, toxicity, and risk assessment of contaminants associated with sediments either above sub-seabed geological formations in marine environments or in high enriched by organic matter in estuarine areas. Recently, the capture of CO₂ in marine environments has been approved and started; it is necessary to address the potential impacts associated with leakages or other events occurring during the procedure of injection and storage of CO2.