4种脂肪酸浮选捕收剂的生物降解性能研究

在好氧的条件下,以活性污泥为接种体,使用改良斯特姆法测试脂肪酸浮选捕收剂(油酸钠、9-羟基硬脂酸钠、硬脂酸钠、蓖麻油酸钠)的生物降解性能,并与利用BOD5/COD进行的可生化评价方法进行比较。结果表明:(1)油酸钠、蓖麻油酸钠的BOD5/COD分别为0.54、0.63,属易生物降解物质;9-羟基硬脂酸钠、硬脂酸钠的BOD5/COD分别为0.36、0.37,属可生物降解物质。(2)油酸钠、9-羟基硬脂酸钠、蓖麻油酸钠28d的生物降解率分别为88.6%、62.2%、100.0%,达到了经济合作与发展组织的OECD-301B生物降解性能实验标准,属于易生物降解物质;硬脂酸钠28d的生物降解率为49.8%,没有达到OECD-301B生物降解性能实验标准,属难生物降解物质。4种脂肪酸浮选捕收剂的生物降解性能依次为:蓖麻油酸钠油酸钠9-羟基硬脂酸钠硬脂酸钠。(3)当有机酸中存在碳碳双键和羟基时,有机酸的生物降解性能都会提高,并且碳碳双键的影响要大于羟基的影响;当二者同时存在时,生物降解性能会大幅度提高。     

Application of the headspace CO2 method (ISO 14 593) to the assessment of the ultimate biodegradability of surfactants: results of a calibration exercise

In the recent review of the control of marketing surfactants used in detergents, the EU decided to increase the severity of the testing procedure by using the criterion of ultimate biodegradability (mineralization) rather than primary biodegradation (removal of the parent molecule) to ensure that possible harmful organic metabolites do not reach the environment. The relatively new ISO headspace CO2 test, considered to be an improvement on the OECD 301B (Sturm CO2) test was chosen. The method was subjected to a ring test by 11 laboratories using one of each of four classes of surfactants plus a poorly degradable reference surfactant; all laboratories satisfactorily applied the method. The necessary addition of silica gel to the medium containing the cationic surfactant, known as a class to be more inhibitory than other classes, was confirmed as a technique for avoiding inhibition of the inoculum. The biodegradability of the surfactants was in general agreement with results reported in the literature and the often reported variable values of % inorganic carbon (IC) produced of the theoretical was found. The anionic and cationic surfactants were readily biodegradable (%IC > 60), the non-ionic surfactant was well below the pass value, while the amphoteric was borderline. The IC production by the blank controls, one of the validity criteria, was about 0.3 mg C/100 ml test medium, equivalent to 3 mg C/l, as recommended in the ISO text. Mild conditions of pre-exposure of the inoculum to the test surfactant did not produce consistent worthwhile effects on either the percentage biodegradation or on its variability.     

Ultimate biodegradation and elimination of antibiotics in inherent tests

The biodegradation and elimination of antibiotics in municipal wastewater treatment plants is of particular concern because sewage is the main exposure route for antibiotics used in human medicine. The inherent biodegradability of 17 antibiotics was determined in a combined test design based on the Zahn-Wellens test (OECD 302 B, 1992) and the CO2-evolution test (OECD 301 B, 1992). CO2 Evolution test (Modified Sturm test). OECD Guideline for the Testing of Chemicals, Paris). Only benzylpenicillin sodium salt (Penicillin G) proved to be ultimately biodegradable, reaching ThCO2 degradation extents of 78-87%. Among the others, only amoxicillin, imipenem and nystatin showed certain ultimate biodegradation in few of the parallel flasks and can be regarded as partially biodegradable with formation of stable metabolites. The DOC-elimination of tetracycline-HCl showed a typical degradation curve starting with 18% and reaching the plateau phase at 80% after 21 days. Nevertheless, the CO2-evolution measured in parallel did not support the data, indicating that the time needed for reaching the adsorption equilibrium was underestimated. Several other antibiotics showed considerable DOC-elimination in the inherent test while only minor incidences of ultimate biodegradation were observed. The combination of CO2-evolution and DOC-elimination is a suitable instrument for assessing the behaviour of chemicals within one test. It enables one to assess both inherent ultimate biodegradability and DOC-elimination by sorption. The applicability of the test is limited to substances with a moderate toxicity.     

Advanced oxidation of a pulp mill bleaching wastewater.

The degradation, by several advanced oxidation reactions, of a pulp mill ECF bleaching effluent, was studied. The initial biodegradability of the organic matter present in the effluent, estimated as the BOD5/COD, was low (0.3). When the effluent was submitted to ozonation and to five different advanced oxidation systems (O3/UV, O3/UV/ZnO, O3/UV/TiO2, O2/UV/ZnO, O2/UV/TiO2), the biodegradability increase significantly. After five minutes of reaction, the O3/UV system appears as the most efficient in to transform the organic matter to more biodegradable forms. A similar effect was observed when the effluent was submitted to an activated sludge treatment. The COD, TOC and toxicity reduction correlated well with the biodegradability enhancement after AOPs treatments.     

Biodegradability testing of synthetic ester lubricants--effects of additives and usage

The optimised biodegradability test system "O2/CO2 Headspace Test with GC-TCD" is used for the assessment of synthetic ester lubricants. The effects of both additives and usage on biodegradability are examined and discussed. Ester based cutting fluids and hydraulic fluids with and without additives are used under defined conditions at machine tools and hydraulic and plain bearing test benches. The lubricants are characterised additionally with respect to kinematic viscosity, acidity and elemental composition. Furthermore, a formulated mineral oil is characterised before and after usage at an hydraulic test bench. The results clearly show that the mineral oil is far less biodegradable than the ester oils and that their biodegradability is not affected by usage. Biodegradability of the ester oils is mainly depending on the characteristics of the base fluids and not affected by the additives. Antioxidants are influencing stability respectively biodegradability indirectly, since they prevent oxopolymerisation effects. Other effects of usage on biodegradation are not detected. In this context, the antioxidants ensure ready biodegradability and have a positive effect on the environmental fate of synthetic ester lubricants.     

A method for measuring the anoxic biodegradability under denitrifying conditions

A test for assessing the anoxic biodegradability of organic compounds under denitrifying conditions is proposed. The method is based on the recovery and quantification of the CO2 produced, which is evidence of complete biodegradation of the test compound (added as the sole carbon source). The tests were carried out in a mineral medium, with nitrate as electron acceptor. Whole lake sediments, sediment extracts and a commercial inoculum were assayed as a possible inoculum source by means of glucose biodegradability tests. It was found that the sediment extracts constitute a suitable and environmentally-relevant inoculum source, since they add non-significant amounts of carbon to the tests. Two xenobiotic compounds, namely, aniline and phenol, were tested in the aforementioned conditions as well as in a standard aerobic biodegradability test. Both aniline and phenol attained a biodegradation level higher than 60% in a short time period (<28 days) and thus can be considered as readily biodegradable in denitrifying environments. Nevertheless, the kinetics obtained in the anoxic test were slower than in aerobic conditions, and even suggested the accumulation of intermediate metabolites in the case of phenol. The results of this study indicate that the fate of xenobiotic compounds under anoxic conditions differs from that observed in an oxic environment, and therefore it should be considered by standard biodegradability testing procedures.     

Biodegradability and ecotoxicity of amine oxide based surfactants

The aerobic and anaerobic biodegradability as well as the aquatic toxicity of two fatty amine oxides and one fatty amido amine oxide were investigated. Aerobic biodegradation was evaluated using the CO(2) headspace test (ISO 14593) and biodegradation under anaerobic conditions was assessed employing a standardised batch test. The three amine oxide based surfactants tested were readily biodegradable under aerobic conditions but only the alkyl amido amine oxide was found to be easily biodegradable under anaerobic conditions. Toxicity to Photobacterium phosphoreum and Daphnia magna was evaluated. Bacteria (EC(50) from 0.11 to 11 mg l(-1)) proved to be more sensitive to the toxic effects of the amine oxide based surfactants than crustacea (IC(50) from 6.8 to 45 mg l(-1)). The fatty amido amine oxide showed the lowest aquatic toxicity.     

Treatment of oily port wastewater effluents using the ultraviolet/hydrogen peroxide photodecomposition system.

This paper presents the nonselective degradation of mechanically pretreated oily wastewater by hydrogen peroxide (H2O2) in the presence and absence of UV irradiation. The effect of chemical oxidation on wastewater biodegradability was also examined. The exclusive use of H2O2 photolyzed by daylight results in quite efficient degradation rates for the low peroxide concentrations used. Higher hydrogen peroxide concentrations inhibit degradation of organic contaminants in the wastewater. The degradation rates of all contaminants are relatively high with an advanced oxidation system (UV/H2O2), but degradation efficiencies are not distinguishably different when 20 or 45 minutes of UV irradiation is used. The excess of H2O2 used in the process can inhibit phenolic degradation and may lead to the formation of a new phenolic fraction. The biodegradability of port wastewater did not increase significantly following the application of the advanced oxidation process.     

Net carbon flux from agricultural ecosystems: methodology for full carbon cycle analyses

Agricultural ecosystems have the potential to sequester carbon in soils by altering agricultural management practices (i.e. tillage practice, cover crops, and crop rotation) and using agricultural inputs (i.e. fertilizers and irrigation) more efficiently. Changes in agricultural practices can also cause changes in CO2 emissions associated with these practices. In order to account for changes in net CO2 emissions, and thereby estimate the overall impact of carbon sequestration initiatives on the atmospheric CO2 pool, we use a methodology for full carbon cycle analysis of agricultural ecosystems. The analysis accounts for changes in carbon sequestration and emission rates with time, and results in values representing a change in net carbon flux. Comparison among values of net carbon flux for two or more systems, using the initial system as a baseline value, results in a value for relative net carbon flux. Some results from using the full carbon cycle methodology, along with US national average values for agricultural inputs, indicate that the net carbon flux averaged over all crops following conversion from conventional tillage to no-till is -189 kg C ha(-1) year(-1) (a negative value indicates net transfer of carbon from the atmosphere). The relative net carbon flux, using conventional tillage as the baseline, is -371 kg C ha(-1) year(-1), which represents the total atmospheric CO2 reduction caused by changing tillage practices. The methodology used here illustrates the importance of (1) delineating system boundaries, (2) including CO2 emissions associated with sequestration initiatives in the accounting process, and (3) comparing the new management practices associated with sequestration initiatives with the original management practices to obtain the true impact of sequestration projects on the atmospheric CO2 pool.     

Catalytic gasification of coal using eutectic salts: recovery,regeneration, and recycle of spent eutectic catalysts

Catalyst recovery studies were conducted for gasified chars produced from steam gasification of Illinois #6 coal catalyzed with two different catalyst systems. A ternary (43.5 mol% Li2CO3-31.5 mol% Na2COr-25 mol% K2CO3) and a binary (29 mol% Na2CO3-71 mol% K2CO3) eutectic catalyst system were used for gasifying coal. Various extraction schemes, such as water extraction, H2SO4 extraction, and acetic acid extraction, were evaluated with respect to their extraction efficiencies. Effects of major process variables, such as solvent-to-char ratio, mixing time, temperature, and concentration, on the extraction efficiency were evaluated. A process schematic for the entire catalyst recovery, regeneration, and recycle scheme was developed and the preliminary process economics were determined based on these extraction schemes. H2SO4 extraction was found to be the most desirable. It also turned out to be more attractive than a once-through throwaway system.     

Ozonation of an azo dye C.I. Remazol Black 5 and toxicological assessment of its oxidation products

The effect of ozonation (20.5 mgl(-1)) on the degradation processes of an azo dye, Remazol Black 5 (RB5; CI) was studied. Conventional parameters such as chemical oxygen demand (COD), total organic carbon (TOC), pH, conductivity, colour removal, biodegradability (BOD(5/28)), and toxic potential of the dye and its degradation products were monitored during the process. The results obtained indicated that ozonation is a highly effective way to remove the colour of a corresponding dye solution. However, a considerable organic load still remained as indicated by high COD and TOC residues. The COD, TOC reductions were about 40% and 25% for 6 h ozonation of 2 gl(-1) RB5 aqueous solution. During the ozonation process the rapid decrease of pH and the sharp increase of conductivity indicated the formation of acidic by-products and small fragments and ions which were identified by high performance ion chromatography. The BOD28 data revealed that first by-products after partial ozonation (10-150 min) of RB5 were more biodegradable than the parent compound and ozonation can enhance the biodegradability of azo dyes. During the first 150 min of total 360 min of oxidation, the formation of first by-products with high toxic potential took place as it could be confirmed by two acute toxicity-screening tests, the bioluminescence test (Vibrio fischerii) and the neutral red cytotoxicity assay (rat hepatoma cells). The significant enhancement of microbial biodegradability after long-term ozonation could also be seen as a decrease of toxic intermediates in correlation with the ozonation time as indicated in BOD28 biological degradation test results.     

Measuring the biodegradability of nonylphenol ether carboxylates, octylphenol ether carboxylates, and nonylphenol

We examined the biodegradability of several metabolites of C8- and C9-alkylphenol ethoxylates, including nonylphenoxyacetic acid (NPEC1), nonylphenoxyethoxyacetic acid (NPEC2), octylphenoxyacetic acid (OPEC1), octylphenoxyethoxyacetic acid (OPEC2), and nonylphenol (NP). Using OECD method 301B (modified Sturm method), OPEC1 and OPEC2 are readily biodegradable: both compounds exceeded 60% of theoretical CO2 formation (ThCO2) by day 28, and required less than 10 days to go from 10% to 60% ThCO2. Also using method 301B, NPEC1 and NPEC2 exceeded 60% ThCO2 at day 28, but did not meet the 10 day window. Using OECD method 301F, the manometric respirometry method that measures oxygen consumption, approximately 62% of NP was biodegraded in 28 days, but required more than 10 days to go from 10% to 60% biodegradation. While the validity of the "10-day window" is currently being debated within OECD, the data show that the common metabolites of C8- and C9-APEs are rapidly degraded in the test systems used, which strongly suggests that they would not accumulate or persist in the environment.     

Methodological trends in the design of recent microenvironmental studies of personal CO exposure

This paper describes the designs of three recent microenvironmental studies of personal exposure to carbon monoxide (CO) from motor vehicle exhaust. These studies were conducted sequentially, first in four California cities (Los Angeles, Mountain View, Palo Alto, and San Francisco), then in Honolulu, and, most recently, in metropolitan Washington, D.C. Though study purposes differed, each study faced common methodological issues related to personal exposure monitors (PEMs), quality assurance and data collection procedures, and the selection of microenvironments for study.Two major objectives of the California cities study were to determine the CO concentrations typically found in commercial settings and to define and classify microenvironments applicable to such settings: The Honolulu study measured merchant exposure to CO in shopping centers attached to semienclosed parking garages during business hours and commuter exposure to CO in vehicles (passenger cars and buses) on congested roadways during peak periods. The intent of the Washington study was to develop a model of commuter exposure to motor vehicle exhaust using CO as an indicator pollutant.Certain trends are discernible from reviewing the three studies. There are clearly trends in PEM development that have expanded instrument capabilities and automated data collection and storage. There are also trends towards more rigorous quality assurance procedures and more standardized protocols for collecting exposure data. Further, one can see a trend towards more elaborate indicators for identifying microenvironments for study. Finally, there is a trend towards using personal monitors in public policy review and evaluation.     

Biological and photochemical degradation rates of diethylenetriaminepentaacetic acid (DTPA) in the presence and absence of Fe(III)

The environmental fate of ethylenediaminetetraacetic acid (EDTA) has been extensively studied, while much less is known about the environmental behaviour of diethylenetriaminepentaacetic acid (DTPA). In this study, it was confirmed that DTPA is persistent toward biodegradation. The biodegradability of DTPA was investigated in the absence and in the presence of Fe(III) by using CO2 evolution test and Manometric respirometry test. The CO2 evolution and oxygen uptake of iron-free (DTPA was added as free acid) and Fe(III)DTPA were less than in inoculum blank. Possible inhibitor effect was analysed by testing biodegradation of sodium benzoate with and without iron-free or Fe(III)DTPA in the Manometric respirometry test. Only slight inhibition was observed when DTPA was added as free acid. Photodegradation of iron-free DTPA and Fe(III)-DTPA complex was studied by using sunlight and UV radiation at the range 315-400 nm emitted by black light lamps. The results indicate that DTPA added as free acid degrades photochemically in humic lake water. Fe(III)DTPA was shown to be very photolabile in humic lake water in the summer; the photochemical half-life was below one hour. Photodegradation products were identified by the mass spectrometric technique (GC-MS). It was shown that photodegradation of Fe(III)DTPA does not result in total mineralization of the compound. Diethylenetriaminetetraacetic acid, diethylenetriaminetriacetic acid, ethylenediaminetriacetic acid, N,N'- and/or N,N-ethylenediaminediacetic acid, iminodiacetate, ethylenediaminemonoacetic acid and glycine were identified as photodegradation products of Fe(III)DTPA. Based on these observations, we propose a photodegradation pathway for Fe(III)DTPA.     

Feasibility study of using brine for carbon dioxide capture and storage from fixed sources

A laboratory-scale reactor was developed to evaluate the capture of carbon dioxide (CO2) from a gas into a liquid as an approach to control greenhouse gases emitted from fixed sources. CO2 at 5-50% concentrations was passed through a gas-exchange membrane and transferred into liquid media--tap water or simulated brine. When using water, capture efficiencies exceeded 50% and could be enhanced by adding base (e.g., sodium hydroxide) or the combination of base and carbonic anhydrase, a catalyst that speeds the conversion of CO2 to carbonic acid. The transferred CO2 formed ions, such as bicarbonate or carbonate, depending on the amount of base present. Adding precipitating cations, like Ca++, produced insoluble carbonate salts. Simulated brine proved nearly as efficient as water in absorbing CO2, with less than a 6% reduction in CO2 transferred. The CO2 either dissolved into the brine or formed a mixture of gas and ions. If the chemistry was favorable, carbonate precipitate spontaneously formed. Energy expenditure of pumping brine up and down from subterranean depths was modeled. We conclude that using brine in a gas-exchange membrane system for capturing CO2 from a gas stream to liquid is technically feasible and can be accomplished at a reasonable expenditure of energy.     

An analysis of the 'Modified Sturm Test' data

The 'Modified Sturm Test' uses carbon dioxide production as the primary end point in assessing the biodegradation potential of organic chemicals. This test was conducted by a commercial laboratory to assess the potential biodegradability of an oil stabilizer sample from an oil company in Canada. There was a high percentage conversion of total organic carbon present in the sample but carbon dioxide measured was low. Many possibilities were analyzed in this paper in order to understand the situation. The analysis showed that the test was subject to criticism from the point of view of CO2 measurement, 10-day window period, and aeration/mixing conditions.     

Solar photocatalytic treatment of landfill leachate using a solid mineral by-product as a catalyst

The treatment of municipal solid waste landfill leachate in a pilot plant made up of solar compound parabolic collectors, using a solid industrial titanium by-product (WTiO₂) containing TiO₂ and Fe(III) as a photocatalyst, was investigated. In the study evidence was found showing that the degradation performed with WTiO₂ was mainly due to the Fe provided by this by-product, instead of TiO₂. However, although TiO₂ had very little effect by itself, a synergistic effect was observed between Fe and TiO₂. The application of WTiO₂, which produced coupled photo-Fenton and heterogeneous catalysis reactions, achieved a surprisingly high depuration level (86% of COD removal), higher than that reached by photo-Fenton using commercial FeSO₄ (43%) in the same conditions. After the oxidation process the biodegradability and toxicity of the landfill leachate were studied. The results showed that the leachate biodegradability was substantially increased, at least in the first stages of the process, and again that WTiO₂ was more efficient than FeSO₄ in terms of increasing biodegradability.     

Production and dispersal of Colletotrichum gloeosporioides spores on Stylosanthes scabra under elevated CO2

This paper reports the effect of twice-ambient (700 ppm) atmospheric CO(2) concentration on infection, disease development, spore production and dispersal of the anthracnose pathogen Colletotrichum gloeosporioides in susceptible (Fitzroy) and partially resistant (Seca) cultivars of the tropical pasture legume Stylosanthes scabra under controlled environment and field conditions. Reduction in plant height due to anthracnose was partially compensated for by growth enhancement at elevated CO(2) in Fitzroy but not in Seca. Anthracnose severity was reduced under elevated CO(2) although the reduction was only significant in Fitzroy. Delayed and reduced germination, germtube growth and appressoria production were partly responsible for the reduced severity. Despite an extended incubation period, C. gloeosporioides developed sporulating lesions faster and produced more spores per day within the same latent period at high CO(2) and ambient CO(2). When Fitzroy seedlings grown at 700 ppm CO(2) were exposed to pathogen inoculum under field conditions, they consistently developed more severe anthracnose with more lesions than seedlings grown at ambient CO(2). The environmental variable, which correlated most strongly with the dispersal and infection of C. gloeosporioides spores in the field, was relative humidity in plant canopy. We have shown that an enlarged Stylosanthes canopy under elevated CO(2) can trap more spores, which can lead to more severe anthracnose under favorable weather. The implications of these findings for perennial Stylosanthes pastures are discussed.     

A batch study on the bio-fixation of carbon dioxide in the absorbed solution from a chemical wet scrubber by hot spring and marine algae

Carbon dioxide mass transfer is a key factor in cultivating micro-algae except for the light limitation of photosynthesis. It is a novel idea to enhance mass transfer with the cyclic procedure of absorbing CO(2) with a high performance alkaline abosorber such as a packed tower and regenerating the alkaline solution with algal photosynthesis. Hence, the algae with high affinity for alkaline condition must be purified. In this study, a hot spring alga (HSA) was purified from an alkaline hot spring (pH 9.3, 62 degrees C) in Taiwan and grows well over pH 11.5 and 50 degrees C. For performance of HSA, CO(2) removal efficiencies in the packed tower increase about 5-fold in a suitable growth condition compared to that without adding any potassium hydroxide. But ammonia solution was not a good choice for this system with regard to carbon dioxide removal efficiency because of its toxicity on HSA. In addition, HSA also exhibits a high growth rate under the controlled pHs from 7 to 11. Besides, a well mass balance of carbon and nitrogen made sure that less other byproducts formed in the procedure of carboxylation. For analysis of some metals in HSA, such as Mg, Mn, Fe, Zn, related to the photosynthesis increased by a rising cultivated pH and revealed that those metals might be accumulated under alkaline conditions but the growth rate was still limited by the ratio of bicarbonate (useful carbon source) and carbonate. Meanwhile, Nannochlopsis oculta (NAO) was also tested under different additional carbon sources. The results revealed that solutions of sodium/potassium carbonate are better carbon sources than ammonia carbonate/bicarbonate for the growth of NAO. However, pH 9.6 of growth limitation based on sodium was lower than one of HSA. The integrated system is, therefore, more feasible to treat CO(2) in the flue gases using the algae with higher alkaline affinity such as HSA in small volume bioreactors.     

Aflatoxin decomposition in various soils

The persistence of aflatoxin in the soil environment could potentially result in a number of adverse environmental consequences. To determine the persistence of aflatoxin in soil, 14C-labeled aflatoxin B1, was added to silt loam, sandy loam, and silty clay loam soils and the subsequent release of 14CO2 was determined. After 120 days of incubation, 8.1% of the original aflatoxin added to the silt loam soil was released as CO2. Aflatoxin decomposition in the sandy loam soil proceeded more quickly than the other two soils for the first 20 days of incubation. After this time, the decomposition rate declined and by the end of the study, 4.9% of the aflatoxin was released as CO2. Aflatoxin decomposition proceeded most slowly in the silty clay loam soil. Only 1.4% of aflatoxin added to the soil was released as CO2 after 120 days incubation. To determine whether aflatoxin was bound to the silty clay loam soil, aflatoxin B1 was added to this soil and incubated for 20 days. The soil was periodically extracted and the aflatoxin species present were determined using thin layer chromatographic (TLC) procedures. After one day of incubation, the degradation products, aflatoxins B2 and G2, were observed. It was also found that much of the aflatoxin extracted from the soil was not mobile with the TLC solvent system used. This indicated that a conjugate may have formed and thus may be responsible for the lack of aflatoxin decomposition.