Management, disposal and recycling of waste industrial organic solvents in Hong Kong.

An attempt has been made to establish a mass balance of industrial organic solvents in Hong Kong. It is estimated that only a small portion, less than 4%, of all the organic solvents consumed in Hong Kong are collected as waste solvents and properly treated, while the remainder are used either in the formulation of solvent containing products, or are lost to the environment through vapour emissions, leaks and spills, or dumped illegally. It was found that solvent recycling has been a common practice in some industries but the existing level of solvent recycling in Hong Kong is difficult to estimate. About 87.4% of all the waste organic solvents disposed of at the licensed facilities are potentially recyclable although whether they can be recycled in practice depends on many factors. Examples of existing waste organic solvent management and recycling practices from selected industries in Hong Kong are presented. The economic feasibility of current and future potential recycling systems is evaluated for a few selected cases. An integrated waste organic solvent management strategy is proposed to minimize adverse impacts of organic solvents to the environment and human health.     

Characterization and adsorption capacity of modified 3D porous aerogel from grapefruit peels for removal of oils and organic solvents

With the rapid industrialization, especially offshore oil exploitation, frequent leakage incidents of oils/organic solvents have adversely affected ecological systems and environmental resources. Therefore, great interest has been shown in developing new materials to eliminate these organic pollutants, which have become worldwide problems. In this study, a cost-effective, environmentally friendly porous aerogel with three-dimensional (3D) structure was prepared from grapefruit peel by a facile hydrothermal method as the adsorbent of oils/organic solvents. The as-prepared modified grapefruit peel aerogel (M-GPA) showed mesoporous structure with high specific surface area of 36.42 m²/g and large pore volume of 0.0371 cm³/g. The excellent hydrophobicity of M-GPA with a water contact angle of 141.2° indicated a strong potential for adsorption of oils and organic solvents. The high adsorption capacity of M-GPA for a series of oils and organic solvents was 8 to 52 times as much as its own weight. Moreover, the M-GPA was easily regenerated and a high adsorption capacity recovery above 97% was maintained after five adsorption–regeneration cycles. Therefore, the M-GPA is a promising recyclable adsorbent for the removal of oils/organic solvents from polluted water.

     

Selection and Substantiation of an Organic Solvent Removal Apparatus at a Print Shop by Comparative Experiments Using the Activated Carbon Adsorption and Catalytic Oxidation Methods

ABSTRACT

The investigation of an appropriate organic solvent removal apparatus for installation in a newly reconstructed print shop as a countermeasure for preventing the exhaust of organic solvents was conducted.

The selection of an organic solvent removal apparatus was made after bench-scale tests of the activated carbon adsorption method and the catalytic oxidation method, both of which are effective for the removal of organic solvents, were performed on the actual exhaust gas at the print shop. The results showed that both methods were efficient enough to be applied to the removal of organic solvents, but the activated carbon adsorption method had many drawbacks, such as the need for frequent replacement of activated carbon and complex maintenance. For the catalytic oxidation method, running costs are high, but there are many merits, such as that the catalysts do not have to be replaced as often and maintenance is simple. After considering these factors, a catalytic oxidation removal apparatus was installed at the new print shop. In the results of the substantiation test on the actual apparatus using mixed catalysts of platinum and manganese plus copper, the removal efficiency was 97.998.7% and the concentration of the outlet exhaust gas was about 10 ppm (the average concentration of the inlet exhaust gas was 528 ppm) at a space velocity of 30,000 hr^-1 and a reaction temperature of 200 °C. The results of this study were substantiated.     

Decomposition of trichloroethylene and 2,4-dichlorophenol by ozonation in several organic solvents

The effects of chemical characteristics of organic solvents on the decomposition rate constants of undissociative trichloroethylene (TCE) and dissociative 2,4-dichlorophenol (2,4-DCP) by ozonation were studied. The TCE and 2,4-DCP decomposition by ozonation in organic solvents followed to the first-order reaction kinetics with respect to TCE or 2,4-DCP concentration. The orders of the rate constants among organic solvents for undissociative TCE and dissociative 2,4-DCP were different indicating that the ozonation rates for undissociative and dissociative compounds were dependent on the chemical property of organic solvent. The decomposition of undissociative TCE by ozonation was a simple electrophilic reaction, which was dependent on acceptor number (AN) of the solvent. On the other hand, the decomposition of dissociative 2,4-DCP was dependent on by the dissociation of the compounds and would be dependent on donor number (DN) of the solvent. Finally, TCE in acetic acid was transformed to chlorinated intermediates and chloride ion and then these intermediates were continuously oxidized to chlorine gas.     

吹扫-捕集法在挥发性有机污染物分析中的应用

吹扫 -捕集法为 2 0世纪 70年代中期推出的痕量挥发性有机化合物的富集方法 ,它具有简便、灵敏度高、富集率高、快速、精密、准确、不使用有机溶剂等特点。 2 0多年以来 ,吹扫 -捕集器和GC、GC/MS等仪器联用测定环境中痕量挥发性有机污染物 ,已获得令人满意的结果 ,因而吹扫 -捕集法将在有机污染分析中得到日益广泛的应用     

Remediation of BTEX and trichloroethene

The widespread use of industrial chemicals in our highly industrialized society has often caused contamination of large terrestrial and marine areas due to the deliberate and accidental release of organic pollutants into the soil and groundwater. In this review, environmental problems arising from the use of chlorinated solvents and BTEX compounds are described, and an overview about active management strategies for remediation with special emphasis on phytoremediation are presented to achieve a reduction of the total mass of chlorinated solvents and BTEX compounds in contaminated areas. Phytoremediation has been proposed as an efficient, low-cost remediation technique to restore areas contaminated with chlorinated solvents and BTEX compounds. The feasibility of phytoremediation as a remediation tool for these compounds is discussed with particular reference to the uptake and metabolism of these compounds, and a future perspective on the use of phytoremediation for the removal of chlorinated solvents and BTEX compounds is given.     

Aged and bound herbicide residues in soil and their bioavailability. Part 2: Uptake of aged and non-extractable (bound) [carbonyl-14C]methabenzthiazuron residues by maize

[Carbonyl-14C]methabenzthiazuron (MBT) was applied to growing winter wheat in an outdoor lysimeter. The amount applied corresponded to 4 kg Tribunil/ha. 140 days after application the 0-2.5 cm soil layer was removed from the lysimeter. This soil contained about 40% of the applied radioactivity. Using 0,01 M CaCl2 solution or organic solvents, the extractable residues were removed from the soil. The bioavailability of the non-extractable as well as aged residues remaining in the soil was investigated in standardized microecosystems containing 1.5 kg of dry soil. During a 4 weeks period the total uptake (4 maize plants/pot) amounted up to 3.6; 2.2; and 0.9% of the radioactivity from soils containing aged MBT residues, MBT residues non-extractable with 0.01 M CaCl2 or MBT residues non-extractable with organic solvents, respectively. About 20% of the radioactivity found in maize leaves represented chromatographically characterized parent compound. At the end of the plant experiment the soil was extracted again with 0.01 M CaCl2 and with organic solvents. The soil extracts and also the organic phases obtained from the aqueous fulvic acid solution contained unchanged parent compound.     

不同洗脱剂对有机氯农药污染场地土壤修复效果比较

为了筛选出能有效修复有机氯农药污染土壤的洗脱剂,选取了16种洗脱剂对2种复合有机氯农药(六六六(HCHs)和滴滴涕(DDTs)、氯丹和灭蚁灵)污染场地土壤进行超声洗脱修复。结果表明,对于HCHs和DDTs复合污染土壤,乙酸乙酯和丙酮对HCHs的洗脱率最高,分别为87.6%和87%,其余有机溶剂对其洗脱率也在70%以上。乙酸乙酯和丙酮对于DDT仍为最优,分别为86.9%与78.4%,其余有机试剂对DDT的洗脱率在60%以上。相对于有机溶剂,表面活性剂对HCHs和DDTs复合污染土壤的洗脱效果不好,总洗脱率均低于4%。同样,对于氯丹和灭蚁灵复合污染土壤,有机溶剂的洗脱效果也明显优于表面活性剂。有机溶剂对灭蚁灵的洗脱率,除了正丙醇较低(63.5%)外,其余均在80%左右。对氯丹的洗脱率,除石油醚(59.6%)、正己烷(49.3%)和正丙醇(42%),其余均在70%以上。相同摩尔浓度的表面活性剂中,吐温80对氯丹的洗脱率为54%,环糊精为20%,鼠李糖脂和曲拉通100为13%左右,其余则小于5%,吐温80对灭蚁灵的洗脱率为29.6%,曲拉通100的为12.4%,鼠李糖脂为5.7%,其余则更低。因此,高效低毒的有机试剂,如乙酸乙酯、丙酮和乙醇等可作为有机氯农药污染土壤修复的首选。     

Occupational health hazards and wide spectrum of genetic damage by the organic solvent fumes at the workplace: A critical appraisal

Environmental Science and Pollution Research - Long-term exposure to organic solvents is known to affect human health posing serious occupational hazards. Organic solvents are genotoxic, and they...     

Solvophobic approach for predicting sorption of hydrophobic organic chemicals on synthetic sorbents and soils

The application of a solvophobic approach for predicting the sorption of hydrophobic organic compounds (HOC) was evaluated with data collected using synthetic sorbents and soils. The experimental data consisted of batch equilibrium sorption coefficients (K_D), as well as soil-TLC and reversed-phase liquid chromatographic (RPLC) retention factors (κ′). All data were collected using aqueous solutions and binary or ternary solvent mixtures of water, methanol, acetone, and acetonitrile. As predicted by the theory, the chromatographic retention factors and sorption coefficients for HOC decreased log-linearly with increasing fraction of organic cosolvent in binary solvents. Model parameters estimated from the binary solvent data could be used to predict sorption (or retention) from ternary solvents. Reasonable agreement was found between model parameters reported in the literature and those estimated using the data from batch sorption, soil-TLC, and RPLC studies.     

Aged and bound herbicide residues in soil and their bioavailability part 2: Uptake of aged and non‐extractable (bound) [carbonyl‐14C] methabenzthiazuron residues by maize

Abstract

[Carbonyl‐ C]methabenzthiazuron (MBT) was applied to growing winter wheat in an outdoor lysimeter. The amount applied corresponded to 4 kg Tribunil/ha. 140 days after application the 0–2,5 cm soil layer was removed from the lysimeter. This soil contained about 40 % of the applied radioactivity. Using 0,01 M CaCl₂ solution or organic solvents, the extractable residues were removed from the soil. The bioavailability of the non‐extractable as well as aged residues remaining in the soil was investigated in standardized microecosystems containing 1.5 kg of dry soil. During a 4 weeks period the total uptake (4 maize plants/pot) amounted up to 3,6; 2,2; and 0,9 % of the radioactivity from soils containing aged MBT residues, MBT residues non‐extractable‐with 0,01 MCaCl₂ or MBT residues non‐extractable with organic solvents, respectively. About 20 % of the radioactivity found in maize leaves represented chromatographically characterized parent compound. At the end of the plant experiment the soil was extracted again with 0,01 M CaCl₂ and with organic solvents. The soil extracts and also the organic phases obtained from the aqueous fulvic acid solution contained unchanged parent compound.     

薄膜干燥法再生聚苯乙烯树脂的研究

利用溶剂溶解回收的聚苯乙烯塑料,将其涂布于不锈钢传送带上,以水蒸气为加热介质,经薄膜干燥法获得再生聚苯乙烯树脂.再生的聚苯乙烯树脂性能优异,溶剂回收率达97%以上.     

An alternative supercritical fluid extraction system for aqueous matrices and its application in pesticides residue analysis

Supercritical fluid extraction (SFE) is a rapid and convenient method for the isolation of organic compounds from environmental samples. This paper describes a supercritical carbon dioxide (CO2) extraction system that uses a newly designed extraction cell to recover organic compounds from an aqueous matrix. Analysis of the extracts by gas chromatography-electron capture detector (GC-ECD) indicated that the herbicide trifluralin (2,6-dinitro-N,N-dipropyl-4-trifluoromethylaniline) could be quantitatively extracted by using the SFE system proposed with small amounts of sample. The percentage of recovery obtained with the SFE system described was twice as high as the result obtained using a conventional solid-phase extraction technique. Extraction by SFE was completed in a short period of time using a simple and low-cost home-made system that did not require the use of organic solvents.     

Mercaptobenzothiazole-on-gold organic phase biosensor systems: 1. Enhanced organosphosphate pesticide determination

This paper reports the construction of the gold/mercaptobenzothiazole/polyaniline/acetylcholinesterase/polyvinylacetate (Au/ MBT/PANI/AChE/PVAc) thick-film biosensor for the determination of certain organophosphate pesticide solutions in selected aqueous organic solvent solutions. The Au/MBT/PANI/AChE/PVAc electrocatalytic biosensor device was constructed by encapsulating acetylcholinesterase (AChE) enzyme in the PANI polymer composite, followed by the coating of poly(vinyl acetate) (PVAc) on top to secure the biosensor film from disintegration in the organic solvents evaluated. The electroactive substrate called acetylthiocholine (ATCh) was employed to provide the movement of electrons in the amperometric biosensor. The voltammetric results have shown that the current shifts more anodically as the Au/MBT/PANI/AChE/PVAc biosensor responded to successive acetylthiocholine (ATCh) substrate addition under anaerobic conditions in 0.1 M phosphate buffer, KCl (pH 7.2) solution and aqueous organic solvent solutions. For the Au/MBT/PANI/AChE/PVAc biosensor, various performance and stability parameters were evaluated. These factors include the optimal enzyme loading, effect of pH, long-term stability of the biosensor, temperature stability of the biosensor, the effect of polar organic solvents, and the effect of non-polar organic solvents on the amperometric behavior of the biosensor. The biosensor was then applied to detect a series of 5 organophosphorous pesticides in aqueous organic solvents and the pesticides studied were parathion-methyl, malathion and chlorpyrifos. The results obtained have shown that the detection limit values for the individual pesticides were 1.332 nM (parathion-methyl), 0.189 nM (malathion), 0.018 nM (chlorpyrifos).     

Factors controlling BTEX and chlorinated solvents plume length under natural attenuation conditions

Natural attenuation is presently used at numerous sites where groundwater is contaminated. In order to simulate this attenuation, reactive transport models are often used but they are quite complex and depend on both physical and chemical conditions in the aquifer. As complex numerical models cannot be used to study all possible cases, we develop here analytical solutions to draw general conclusions. Our strategy, called MIKSS (Mixed Instantaneous and Kinetics Superposition Sequence), allows the calculation of the concentrations of all reacting substances in a plume. It is an extension of the superimposition principle that is able to treat the case of joint kinetics and instantaneous reactions. The basic equations have been extended to treat different reactions that occur in the plume core and at its fringe. At first we consider one organic substance degraded under all oxidising conditions (toluene for instance). For this problem the size of the plume depends on the reduced source width and on the ratio of the organic substance concentration to the sum of the electron acceptors' concentrations. For several BTEX substances having different degradation behaviour the formulation is similar, but leads to quite different plume lengths for each substance. Contrary to the case of one substance, the plumes can be quite long and may not satisfy the target risk level. For chlorinated solvents we developed a specific approach to take under consideration all reactions and particularly the competition for hydrogen. A formula is given to assess the size of the plume core, i.e. the zone with highly reducing conditions. The factors influencing the core length are the same as for BTEX (source width, dispersivity, organic carbon content). The size of the TCE plume is calculated from the plume core length and the kinetic constant of TCE degradation. Using assumptions of degradation constants for DCE and VC it is also possible to calculate the longitudinal concentration profile of these substances. The degradation of moderately substituted solvents under oxic conditions reduces the size of their plumes but under these conditions TCE becomes the major threat. Among the conditions studied in this paper, very few chlorinated solvents sites can lead to a negligible risk at an acceptable distance from the source.     

Non-steady state partitioning of dry cleaning surfactants between tetrachloroethylene (PCE) and water in porous media

Trapped organic solvents, in both the vadose zone and below the water table, are frequent sources of environmental contamination. A common source of organic solvent contamination is spills, leaks, and improper solvent disposal associated with dry cleaning processes. Dry cleaning solvents, such as tetrachloroethylene (PCE), are typically enhanced with the addition of surfactants to improve cleaning performance. The objective of this work was to examine the partitioning behavior of surfactants from PCE in contact with water. The relative rates of surfactants partitioning and PCE dissolution are important for modeling the behavior of waste PCE in the subsurface, in that they influence the interfacial tension of the PCE, and how (or if) interfacial tension changes over time in the subsurface. The work described here uses a flow-through system to examine simultaneous partitioning and PCE dissolution in a porous medium. Results indicate that both nonylphenol ethoxylate nonionic surfactants and a sulfosuccinate anionic surfactant partition out of residual PCE much more rapidly than the PCE dissolves, suggesting that in many cases interfacial tension changes caused by partitioning may influence infiltration and distribution of PCE in the subsurface. Non-steady-state partitioning is found to be well-described by a linear driving force model incorporating measured surfactant partition coefficients.     

A History of the Production and Use of Carbon Tetrachloride,Tetrachloroethylene, Trichloroethylene and 1,1,1-Trichloroethane in the United States: Part 1--Historical Background; Carbon Tetrachloride and Tetrachloroethylene

Carbon tetrachloride (CTC), tetrachloroethylene (PCE), trichloroethylene (TCE) and 1,1,1-trichloroethane (TCA) were four of the most widely used cleaning and degreasing solvents in the United States. These compounds were also used in a wide variety of other applications. The history of the production and use of these four compounds is linked to the development and growth of the United States' synthetic organic chemical industry, and historical events that affected the development and use of chlorinated solvents in general. Part 1 of this article includes a discussion of the historical background common to each of the four solvents, followed by discussion on the history of CTC and PCE. In the early years of the 20th century, CTC became the first of the four solvents to come into widespread use. CTC was used as a replacement for petroleum distillates in the dry-cleaning industry, but was later replaced by PCE. In the 1990s, CTC was phased out under the Montreal Protocol due to its role in stratospheric ozone depletion.     

Solvent toxicity to amphibian embryos and larvae

Organic micropollutants are often damaging for aquatic organisms. Being usually hydrophobic compounds, they are often dissolved in an organic co-solvent which increases their solubility in water. The aim of this study was to study the toxicity of various solvents on embryos (protected or not by jelly coat) and on tadpoles of the common frog (Rana temporaria). Tested solvents were methanol (MeOH), methylene chloride (CH(2)Cl(2)), dimethyl sulfoxyde (DMSO), acetone (Ac) and ethanol (EtOH). Embryos exhibited higher mortality rates than tadpoles. Embryos with jelly were more sensitive to high concentration of solvents than embryos without jelly (except for acetone). According to these results, Ac, DMSO and CH(2)Cl(2) can be used as co-solvents in water to help the dissolution of micropollutants at concentration equal to or lower than 0.001 ml/l for frog embryos, and EtOH, Ac and CH(2)Cl(2) at concentration equal to or lower than 0.01 ml/l for Rana temporaria tadpoles.     

Green pre-concentration techniques during pesticide analysis in food samples

The ever-increasing demand for determining pesticides at low concentration levels in different food matrices requires a preliminary step of pre-concentration which is considered a crucial stage. Recently, the parameter of “greenness” during sample pre-concentration of pesticides in food matrices is as important as selectivity in order to avoid using harmful organic solvents during sample preparation. Developing new green pre-concentration techniques is one of the key subjects. Thus, to reduce the impact on the environment during trace analysis of pesticides in food matrices, new developments in pre-concentration have gone in three separate directions: the search for more environmentally friendly solvents, miniaturization and development of solvent-free pre-concentration techniques. Eco-friendly solvents such as supercritical fluids, ionic liquids and natural deep eutectic solvents have been developed for use as extraction solvents during pre-concentration of pesticides in food matrices. Also, miniaturized pre-concentration techniques such as QuEChERS, dispersive liquid–liquid micro-extraction and hollow-fiber liquid-phase micro-extraction have been used during trace analysis of pesticides in food samples as well as solvent-free techniques such as solid-phase micro-extraction and stir bar sorptive extraction. All these developments which are aimed at ensuring that pesticide pre-concentration in different food matrices is green are critically reviewed in this paper.     

An alternative supercritical fluid extraction system for aqueous matrices and its application in pesticides residue analysis

Abstract

Supercritical fluid extraction (SFE) is a rapid and convenient method for the isolation of organic compounds from environmental samples. This paper describes a supercritical carbon dioxide (CO₂) extraction system that uses a newly designed extraction cell to recover organic compounds from an aqueous matrix. Analysis of the extracts by gas chromatography‐electron capture detector (GC‐ECD) indicated that the herbicide trifluralin (2,6‐dinitro‐N,N‐dipropyl‐4‐trifluoromethylaniline) could be quantitatively extracted by using the SFE system proposed with small amounts of sample. The percentage of recovery obtained with the SFE system described was twice as high as the result obtained using a conventional solid‐phase extraction technique. Extraction by SFE was completed in a short period of time using a simple and low‐cost home‐made system that did not require the use of organic solvents.