Size and performance of anoxic limestone drains to neutralize acidic mine drainage

Acidic mine drainage (AMD) can be neutralized effectively in underground, anoxic limestone drains (ALDs). Owing to reaction between the AMD and limestone (CaCO3), the pH and concentrations of alkalinity and calcium increase asymptotically with detention time in the ALD, while concentrations of sulfate, ferrous iron, and manganese typically are unaffected. This paper introduces a method to predict the alkalinity produced within an ALD and to estimate the mass of limestone required for its construction on the basis of data from short-term, closed-container (cubitainer) tests. The cubitainer tests, which used an initial mass of 4 kg crushed limestone completely inundated with 2.8 L AMD, were conducted for 11 to 16 d and provided estimates for the initial and maximum alkalinities and corresponding rates of alkalinity production and limestone dissolution. Long-term (5-11 yr) data for alkalinity and CaCO3 flux at the Howe Bridge, Morrison, and Buck Mountain ALDs in Pennsylvania, USA, indicate that rates of alkalinity production and limestone dissolution under field conditions were comparable with those in cubitainers filled with limestone and AMD from each site. The alkalinity of effluent and intermediate samples along the flow path through the ALDs and long-term trends in the residual mass of limestone and the effluent alkalinity were estimated as a function of the computed detention time within the ALD and second-order dissolution rate models for cubitainer tests. Thus, cubitainer tests can be a useful tool for designing ALDs and predicting their performance.     

Novel passive co-treatment of acid mine drainage and municipal wastewater

A laboratory-scale, four-stage continuous-flow reactor system was constructed to test the viability of high-strength acid mine drainage (AMD) and municipal wastewater (MWW) passive co-treatment. Synthetic AMD of pH 2.6 and acidity of 1870 mg L(-1) as CaCO3 equivalent containing a mean 46, 0.25, 2.0, 290, 55, 1.2, and 390 mg L(-1) of Al, As, Cd, Fe, Mn, Pb, and Zn, respectively, was added at a 1:2 ratio with raw MWW from the City of Norman, OK, to the system which had a total residence time of 6.6 d. During the 135-d experiment, dissolved Al, As, Cd, Fe, Mn, Pb, and Zn concentrations were consistently decreased by 99.8, 87.8, 97.7, 99.8, 13.9, 87.9, and 73.4%, respectively, pH increased to 6.79, and net acidic influent was converted to net alkaline effluent. At a wasting rate of 0.69% of total influent flow, the system produced sludge with total Al, As, Cd, Cr, Cu, Fe, Pb, and Zn concentrations at least an order of magnitude greater than the influent mix, which presents a metal reclamation opportunity. Results indicate that AMD and MWW passive co-treatment is a viable approach to use wastes as resources to improve water quality with minimal use of fossil fuels and refined materials.     

Passive treatment of acid mine drainage with high metal concentrations using dispersed alkaline substrate

Passive treatment systems based on the dissolution of coarse calcite grains are widely used to remediate acid mine drainage (AMD). Unfortunately, they tolerate only low metal concentrations or acidity loads, because they are prone to passivation (loss of reactivity due to coating) and/or clogging (loss of permeability) by precipitates. To overcome these problems, a dispersed alkaline substrate (DAS) composed of a fine-grained alkaline reagent (calcite sand) mixed with a coarse inert matrix (wood chips) was developed. The small grains provide a large reactive surface and dissolve almost completely before the growing layer of precipitates passivates the substrate, whereas the dispersion of nuclei for precipitation on the inert surfaces retards clogging. Chemical and hydraulic performance of DAS was investigated in two laboratory columns fed at different flow rates with natural AMD of pH 2.3 to 3.5 and inflow net acidity 1350 to 2300 mg/L as CaCO(3). The DAS columns removed 900 to 1600 mg/L net acidity, 3 to 4.5 times more than conventional passive treatment systems. Regardless of the flow rate employed, Al, Fe(III), Cu, and Pb were virtually eliminated. Minor Zn, Ni, and Cd were removed at low flow rates. High acidity removal is possible because these metals accumulate intentionally in DAS, and their precipitation promotes further calcite dissolution. During 15 mo, DAS operated without clogging at 120 g acidity/m(2).d, four times the loading rate recommended for conventional passive systems; DAS may therefore be capable of treating AMD at sites where influent chemistry precludes the use of other passive systems.     

Life cycle assessment analysis of active and passive acid mine drainage treatment technologies

Acid mine drainage (AMD), resulting from open-cast coal mining, is currently one of the largest environmental challenges facing the mining industry. In this study, a life cycle assessment (LCA) was conducted to evaluate the environmental impacts associated with the construction, operation and maintenance of different AMD treatment options typically employed. LCA is a well-reported tool but is not documented for AMD treatment systems despite their ubiquitous implementation worldwide. This study conducted detailed LCA analysis for various passive and active AMD treatment approaches implemented or considered at a major coal mine in New Zealand using a comparative functional unit of kg acidity removed per day for each treatment option. Eight treatment scenarios were assessed including active limestone and hydrated lime treatments, and compared to passive treatments using limestone and waste materials such as mussel shells. Both midpoint and endpoint LCA impact categories were assessed. Generally, the active treatment scenarios demonstrated greater LCA impacts compared to an equivalent level of treatment for the passive treatment approaches. Lime slaking had the greatest LCA impacts, while passive treatment approaches incurred consistently less impacts except for one passive treatment with a purchased energy scenario. A 50% reduction in transportation distances resulted in the lowest LCA impacts for all scenarios. This study highlights the importance of evaluating the environmental and social impacts of AMD treatment for the mining industry.     

ACID MINE DRAINAGE (AMD) AND ITS IMPACT ON A SMALL VIRGINIA STREAM1

ABSTRACT: A study was conducted to 1) chemically characterize three AMD streams entering Chestnut Creek in southwestern Virginia below the town of Galax, Virginia, and 2) to assess the biological and chemical alterations in the creek. Over a six mile reach, the benthic macroinvertebrate population was reduced to zero, the naturally low alkalinity (～25mg/1) of the stream was reduced to less than 5 mg/1, and the pH was reduced from 7.2 to 6.3. Increased concentration of iron from less than 0.01 mg/I to more than 4.0 mg/1 were accompanied by the deposition of a coating of iron hydroxide up to 0.25 in. thick in the stream bed, a phenomenon most likely responsible for the absence of benethic macroinvertebrates. In situ bioassays with bluegill sunfish and one snail species showed that the creek water, after confluence with all the AMD streams, was not toxic in 192 hours to fish, and snails survived 96 hours before they began to die. The undiluted AMD itself was highly toxic.     

Natural alkalinity generation in neutral lakes affected by acid mine drainage

Lakes in surface mining areas are often subject to continuous loads of acid mine drainage. The knowledge of internal alkalinity generation in a lake is necessary to predict if the lake will stay circumneutral or may acidify. The most important processes of alkalinity production in lakes are sulfate reduction, denitrification, and the burial of N in the sediment. By summarizing data from the literature, we present probable rates of these different processes in circumneutral mining lakes. The critical acidity load that can probably be compensated for by internal processes, is 5.09 mmol(-) m(-2) d(-1) in productive lakes and 0.50 mmol(-) m(-2) d(-1) in less productive lakes. Under the assumption that methanogenesis is inhibited by high sulfate concentrations, the highest probable acidity loads in such lakes are 6.85 mmol(-) m(-2) d(-1) and 1.06 mmol(-) m(-2) d(-1), respectively. Denitrification, sulfate reduction, and N burial contributed significantly to total alkalinity production. Sulfate reduction had the largest potential. However, existing models cannot predict alkalinity generation from sulfate concentrations alone because the long-term stability of reduced S compounds in the sediment is crucial for a sustainable biological alkalinity generation. The larger acid-neutralizing potential of higher trophic lakes is caused both by higher rates of microbial activity and by a greater stability of reduced reaction products in the sediment. The largest uncertainties in our knowledge with respect to the total alkalinity budget are related to microbial processes in sulfate-rich freshwater lakes and the long-term stability of reduced reaction products in the sediment.     

A MODEL OF THE BEHAVIOR OF pH DETERMINING PARAMETERS IN IMPOUNDMENTS1

ABSTRACT: A computer model capable of describing the behavior of pH-determining parameters in an impoundment is presented. The steady-state model, based upon principles of water chemistry, applies the complete-mix concept to the routing of the chemical quantities, alkalinity and CO₂ acidity. An iterative procedure is used to account for surface mass transfer of carbon dioxide. A fourth-degree polynomial is solved for the hydrogen ion concentration at each point of routed alkalinity and CO₂ acidity concentrations. Field data required to verify and apply the model are described, including an example application to the Loyalhanna Creek Reservoir.     

Long-term evaluation of coal fly ash and mine tailings co-placement: A site-specific study

This study presents the results of a laboratory investigation conducted to evaluate the efficiency of coal fly ash to control the formation of acid mine drainage (AMD) from mine waste. Site-specific materials, coal fly ash from Atikokan Thermal Generating Station and mine tailings from Musselwhite mine, were mixed at different proportions for the investigation of the drainage chemistry and the optimal mix using static testing (acid–base accounting) and kinetic (column) testing. The acid–base accounting (ABA) results indicated that the fly ash possessed strong alkaline (neutralization) potential (NP) and could be used in the management of reactive mine tailings, thus ensuring prevention of AMD in the long-term. Column tests conducted in the laboratory to further investigate long-term performance of fly ash in the neutralization and prevention of acid mine drainage from tailings similarly showed that mixing fly ash with mine tailings reduces dissolution of many heavy metals from tailings by providing alkalinity to the system. It was found that a fly ash to tailings mass ratio equal to or greater than 15% can effectively prevent AMD generation from Musselwhite mine tailings in the co-placement approach.     

Anaerobic whey treatment by a stirred sequencing batch reactor (ASBR): effects of organic loading and supplemented alkalinity

An assessment was made of cheese whey treatment in a mechanically stirred anaerobic sequencing batch reactor (ASBR) containing granular biomass. The effect of increasing organic load and decreasing influent alkalinity supplementation (as sodium bicarbonate) was analyzed. The reactor operated on 8-h cycles with influent COD concentrations of 500, 1000, 2000 and 4000 mg/L, corresponding to volumetric organic loads of 0.6 to 4.8 mgCOD/L.d. Organic COD removal efficiencies were always above 90% for filtered samples. These results were obtained with an optimized alkalinity supplementation of 50% (ratio between mass of NaHCO3 added and mass of influent mgNaHCO3/mgCOD) in the assays with 500 and 1000 mgCOD/L and of 25% in the assays with 2000 and 4000 mgCOD/L. Initial alkalinity supplementation was equal to the mass of influent COD (100%). The system showed formation of viscous polymer-like substances. These were probably of microbiological origin occurring mainly at influent CODs of 2000 and 4000 mg/L and caused some biomass flotation. This could, however be controlled to enable efficient and stable reactor operation.     

MODELING ACID MINE DRAINAGE ON A WATERSHED SCALE FOR TMDL CALCULATIONS1

ABSTRACT: The Cheat River of West Virginia is impaired by acid mine drainage (AMD). Fifty‐five of its river segments were placed on the 303(d) list, which required calculations of total maximum daily load (TMDL) to meet the water quality criteria for pH, total iron, aluminum, manganese, and zinc. An existing watershed model was enhanced to simulate AMD as nonpoint source load. The model divided a watershed into a network of catchments and river segments. Each catchment was divided into soil layers, which could contain pyrite, calcite and other minerals. A kinetic expression was used to simulate pyrite oxidation as a function of oxygen in the soil voids. Oxygen in the soil voids was consumed by pyrite oxidation and replenished by earth breathing. The by‐products of pyrite oxidation were calculated according to its mass action equations. Chemical equilibrium was used to account for the speciation of ferrous and ferric irons and precipitation of metal hydroxides. Simulated hydrology and water quality were compared to available data. The USEPA used the calibrated model to calculate the TMDLs in the Cheat River Watershed.     

pH,dissolved oxygen,and adsorption effects on metal removal in anaerobic bioreactors

Anaerobic bioreactors were used to test the effect of the pH of influent on the removal efficiency of heavy metals from acid-rock drainage. Two studies used a near-neutral-pH, metal-laden influent to examine the heavy metal removal efficiency and hydraulic residence time requirements of the reactors. Another study used the more typical low-pH mine drainage influent. Experiments also were done to (i) test the effects of oxygen content of feed water on metal removal and (ii) the adsorptive capacity of the reactor organic substrate. Analysis of the results indicates that bacterial sulfate reduction may be a zero-order kinetic reaction relative to sulfate concentrations used in the experiments, and may be the factor that controls the metal mass removal efficiency in the anaerobic treatment systems. The sorptive capacities of the organic substrate used in the experiments had not been exhausted during the experiments as indicated by the loading rates of removal of metals exceeding the mass production rates of sulfide. Microbial sulfate reduction was less in the reactors receiving low-pH influent during experiments with short residence times. Sulfate-reducing bacteria may have been inhibited by high flows of low-pH water. Dissolved oxygen content of the feed waters had little effect on sulfate reduction and metal removal capacity.     

Response of Fish and Macroinvertebrate Bioassessment Indices to Water Chemistry in a Mined Appalachian Watershed

Multimetric indices based on fish and benthic macroinvertebrate assemblages are commonly used to assess the biological integrity of aquatic ecosystems. However, their response to specific stressors is rarely known. We quantified the response of a fish-based index (Mid-Atlantic Highlands Index of Biotic Integrity, MAH-IBI) and a benthic invertebrate-based index (West Virginia Stream Condition Index, WV-SCI) to acid mine drainage (AMD)-related stressors in 46 stream sites within the Cheat River watershed, West Virginia. We also identified specific stressor concentrations at which biological impairment was always or never observed. Water chemistry was extremely variable among tributaries of the Cheat River, and the WV-SCI was highly responsive across a range of AMD stressor levels. Furthermore, impairment to macroinvertebrate communities was observed at relatively low stressor concentrations, especially when compared to state water quality standards. In contrast to the WV-SCI, we found that the MAH-IBI was significantly less responsive to local water quality conditions. Low fish diversity was observed in several streams that possessed relatively good water quality. This pattern was especially pronounced in highly degraded subwatersheds, suggesting that regional conditions may have a strong influence on fish assemblages in this system. Our results indicate that biomonitoring programs in mined watersheds should include both benthic invertebrates, which are consistent indicators of local conditions, and fishes, which may be indicators of regional conditions. In addition, remediation programs must address the full suite of chemical constituents in AMD and focus on improving linkages among streams within drainage networks to ensure recovery of invertebrate and fish assemblages. Future research should identify the precise chemical conditions necessary to maintain biological integrity in mined Appalachian watersheds.     

Back to the basics – Estimating the sensitivity of freshwater to acidification using traditional approaches

This study examines the effects of acidifying sulphur emissions on freshwater ecosystems in the traditional territory of Treaty 8 First Nations in British Columbia (BC). Due to the absence of detailed water chemistry data for most lakes in the region, revised empirical methods for estimating freshwater sensitivity to acidification are formulated using linear regression relationships between individual chemical measurements, and critical loads of acidity calculated using the Steady State Water Chemistry (SSWC) model. Lake alkalinity is the most effective chemical indicator of acidification sensitivity in northeast BC. Critical loads of acidity (CL(A)) estimated using alkalinity range from 0.0827 to 9.48 keq ha^?1 yr^?1. Sulphur deposition estimates range from 0.0113 to 0.303 keq ha^?1 yr^?1 and do not exceed the estimated CL(A) at any of the study lakes. The spatial situation of both the lakes and the emission sources is responsible for the lack of exceedances, and expanded/continued monitoring is recommended to account for geological variability and source proliferation. Measurements of lake conductivity and alkalinity provide a means of community monitoring for freshwater acidification sensitivity as part of cumulative effects management strategies.     

SENSITIVITY OF HIGH-ELEVATION STREAMS IN THE SOUTHERN BLUE RIDGE PROVINCE TO ACIDIC DEPOSITION1

ABSTRACT: The Southern Blue Ridge Province, which encompasses parts of northern Georgia, eastern Tennessee, and western North Carolina, has been predicted to be sensitive to impacts from acidic deposition, owing to the chemical composition of the bedrock geology and soils. This study confirms the predicted potential sensitivity, quantifies the level of total alkalinity and describes the chemical characteristics of 30 headwater streams of this area. Water chemistry was measured five times between April 1983 and June 1984 at first and third order reaches of each stream during baseflow conditions. Sensitivity based on total alkalinity and the Calcite Saturation Index indicates that the headwater streams of the Province are vulnerable to acidification. Total alkalinity and p11 were generally higher in third order reaches (mean, 72 μeq/θ and 6.7) than in first order reaches (64 μeq/θ and 6.4). Ionic concentrations were low, averaging 310 and 340 μeq/θ in first and third order reaches, respectively. A single sampling appears adequate for evaluating sensitivity based on total alkalinity, but large temporal variability requires multiple sampling for the detection of changes in pH and alkalinity over time. Monitoring of stream water should continue in order to detect any subtle effects of acidic deposition on these unique resource systems.     

An experimental study on the influence of zeolite on changes of pH and alkalinity in anaerobic treatment of compost leachate

With the increase of urbanization, municipal solid waste has also increased. Therefore, the need for solid waste management is also increasing compared with earlier decades. Composting is a good option for the recycling of solid waste; however, it produces leachate, which requires proper treatment systems to prevent environmental degradation. Due to high chemical oxygen demand (COD) concentrations in compost leachate, anaerobic treatment is the best option for handling the effluent, and an anaerobic baffled reactor (ABR) is one such anaerobic reactor that can be used for its treatment. Because of high ammonia and heavy metal concentrations, as well as the possibility of sludge washout in ABRs, it is important to use proper media, such as zeolite, which can reduce inhibition effects and sludge washout from the reactor. Anaerobic treatment, especially during the methanogenesis phase, is sensitive, and pH and alkalinity are parameters that influence the treatment. Therefore, adjusting these parameters within a normal range is very important to the proper functioning of anaerobic systems. In this study, a pilot‐scale ABR was used, and the last 4 of the 8 ABR compartments were filled with zeolite. The bioreactor was operated at hydraulic retention times (HRT) of 3, 4, and 5 days, with zeolite filling ratios of 10%, 20%, and 30%, and influent COD concentrations of 10,000, 20,000, and 30,000 milligrams per liter (mg/L). In this study, pH value was 6.43 ± 0.1, 6.96 ± 0.3, and 6.96 ± 0.25 at filling ratios of 10%, 20%, and 30%, respectively. According to the results, in all filling ratios, no significant changes were observed in the pH value when the organic loading rate increased and its amount was within a constant range. Influent alkalinity was equal to 2015 ± 510, 2884 ± 505, and 4154 ± 233 milligrams of calcium carbonate per liter (mg CaCO₃/L) at influent COD concentrations of 10,000, 20,000, and 30,000 mg/L, respectively, and in effluent, they were 2536 ± 336, 3379 ± 639, and 4377 ± 325 mg CaCO₃/L, respectively. The amount of alkalinity in the effluent increased compared with the alkalinity in the influent. The results show that the amount of alkalinity in the influent and effluent was similar, and the alkalinity enhancement was lower when the filling ratio was increased from 10% to 20%, and 20% to 30%. Comparisons of the results from zeolite with and without biofilm showed that, in cases of zeolite with biofilm, the amounts of silica and oxygen decreased and the amount of carbon increased, and it showed the formation of biofilm on the surface of zeolite. In addition, the absence of sodium in the zeolite with the biofilm indicated that sodium was exchanged with ammonium ions. According to the results, zeolite can be used in anaerobic reactors as a medium, and it also reduces fluctuations in pH and alkalinity at different organic loading rates, providing a normal range for anaerobic treatment.     

Evaluation of leachates from coal refuse blended with fly ash at different rates

There is great interest in returning coal combustion products to mining sites for beneficial reuse as liming agents. A column study examined the effects of blending two coal fly ashes with an acid-forming coal refuse (4% pyritic S). Both fly ashes were net alkaline, but had relatively low neutralizing capacities. One ash with moderate alkalinity (CRF) was bulk blended with coal refuse at 0, 20, and 33% (w/w), while another lower alkalinity ash (WVF) was blended at 0, 5, 10, 20, and 33% (w/w). The columns were leached (unsaturated) weekly with 2.5 cm of simulated precipitation for >150 wk. Where high amounts of ash alkalinity (>20% w/w) were mixed with the coal refuse, pyrite oxidation was controlled and leachate pH was >7.0 with low metal levels throughout the study. At lower rates of alkalinity loading, trace metals were sequentially released from the WVF ash as the 5, 10, and 20% treatments acidified due to pyrite oxidation. Lechate metals increased in proportion to the total amounts applied in the ash. In this strongly acidic environment, metals such as Mn, Fe, and Cu were dissolved and leached from the ash matrix in large quantities. If ash is to be beneficially reused in the reclamation of acid-producing coal refuse, the alkalinity and potential acidity of the materials must be balanced through the appropriate addition of lime or other alkaline materials to the blend. Highly potentially acidic refuse material, such as that used here, may not be suitable for ash/refuse codisposal scenarios.     

ESTIMATION OF DAILY TEMPERATURE MEANS USING ELEVATION AND LATITUDE IN MOUNTAINOUS TERRAIN1

ABSTRACT A model was developed for predicting mean daily, mean daily minimum, and mean daily maximum temperatures in West Virginia. The model is easily used since the only inputs are elevation, latitude, and julian date. With local calibration, the model is expected to apply to other areas in the Appalachian region.     

DECLINING INTENSITY OF ACID MINE DRAINAGE IN THE NORTHERN APPALACHIAN BITUMINOUS COAL FIELDS: MAJOR ALLEGHENY RIVER TRIBUTARIES1

ABSTRACT: For more than 30 years, a program of continuous monitoring of pH, acidity, alkalinity, and other parameters has been maintained on a network of large streams degraded by acid mine drainage in the northern Appalachian high sulfur coal region. Continuous records since 1952 are available at a number of stations, and at several stations, acidity records date back to 1930. Comparable analysis techniques were maintained over the period of record, assuring the long term continuity of the database. This monitoring program has captured integrated long term trends within large and complex watersheds with numerous and varied types of mine discharges. The focus of this paper is a historical trend analysis of lightly to severely acid degraded major tributaries of the Allegheny River. Over the past three decades, all of the Allegheny River drainage basin stations have demonstrated steady and substantial declines in acidity and associated increases in pH and alkalinity. The average recorded decline in total acidity at four stations monitored since the 1950s was 94 percent. Since the 1970s, acidity declined by an average of 63 percent at 10 stations. Oxidative exhaustion of pyritic minerals exposed by mining is proposed as a major factor influencing these trends.     

Rapid manganese removal from mine waters using an aerated packed-bed bioreactor

In the UK, the Environmental Quality Standard for manganese has recently been lowered to 30 microg/L (annual average), which is less than the UK Drinking Water Inspectorate's Maximum Permitted Concentration Value (50 microg/L). Current passive treatment systems for manganese removal operate as open-air gravel-bed filters, designed to maximize either influent light and/or dissolved oxygen. This requires large areas of land. A novel enhanced bioremediation treatment system for manganese removal has been developed that consists of a passively aerated subsurface gravel bed. The provision of air at depth and the use of catalytic substrates help overcome the slow kinetics usually associated with manganese oxidation. With a residence time of only 8 h and an influent manganese concentration of approximately 20 mg/L, >95% of the manganese was removed. The treatment system also operates successfully at temperatures as low as 4 degrees C and in total darkness. These observations have positive implications for manganese treatment using this technique in both colder climates and where large areas of land are unavailable. Furthermore, as the operation of this passive treatment system continually generates fresh manganese oxyhydroxide, which is a powerful sorbent for most pollutant metals, it potentially has major ancillary benefits as a removal process for other metals, such as zinc.     

HYDROLOGIC ANALYSIS OF DISCHARGE SUSTAINABILITY FROM AN ABANDONED UNDERGROUND COAL MINE1

ABSTRACT: Discharge from flooded abandoned subsurface coal mines is considered a potential source for water supplies where other acceptable water sources are not available. The objective of this study was to develop procedures for determining sustainability of mine‐water discharge using rainfall and discharge data for a case study site. The study site is located in southwest Virginia where Late Paleozoic sequences of sandstone, coal, and shale predominate. A rain gauge and a flow rate monitoring system were installed at the site and data were collected for a period of 100 days. The recording period corresponded with one of the driest periods in recent years and, therefore, provided valuable information regarding the flow sustainability during baseflow conditions. From available data on underground mining patterns, geology, and ground water flow regimes, it was determined that a coal mine aquifer exhibits hydraulic characteristics very similar to the extremely heterogeneous systems observed in karst aquifers, and the mine discharge is analogous to springflow. Thus, techniques commonly used in karst‐water systems and springflow analysis were used to develop rainfall/mine‐discharge relationships. Springflow recession analysis was performed on five rainfall recessions and the coefficient for each recession was compared and interpreted in light of known geologic information. It was found that the recession coefficients described the mine discharge adequately and the mine aquifer response to a rainfall pulse was very similar to the response from certain types of karst aquifers. A cross‐correlation analysis was performed to verify the results of the recession analysis and to develop a “black box” statistical model for discharge data. The correlation analysis proved the validity of springflow recession analysis for mine discharge. The recorded data length was not adequate to create a statistical model, however, but a procedure was proposed for a statistical model that could be used with large flow records. For the study site, the mine discharge was found to be sustainable for a prolonged period of time.