Bioavailability of biosolids molybdenum to corn

This study was part of a larger effort to generate field data appropriate to the assessment of biosolids molybdenum (Mo) risk to ruminants. Corn (Zea mays L.) is an important component of cattle diet, and is a logical crop for biosolids amendment owing to its high N requirement. Paired soil and corn stover samples archived from two unique field experiments were analyzed to quantify the relationship (uptake coefficient, UC) between stover Mo and soil Mo load. Both studies used biosolids with total Mo concentrations typical of modern materials. Data from long-term (continuous corn) plots in Fulton County, IL confirm expected low Mo accumulation by corn stover, even at very high biosolids loads and soil Mo loads estimated to be near 18 kg Mo ha(-1). Uptake slopes were actually negative, but USEPA protocol would assign UC values of 0.001. Data from plots in Minnesota also suggested essentially no correlations between stover Mo and soil Mo loads for continuous corn. However, greater Mo accumulation in corn grown following soybean [Glycine max (L.) Merr.] suggests the possibility of enhanced Mo bioavailability to corn in corn-soybean rotations. Nevertheless, molybdenosis risk to cattle consuming corn stover produced on biosolids-amended land is small as stover Mo concentrations were always low and stover Cu to Mo ratios exceeded 2:1, which avoids molybdenosis problems.     

Trace element concentrations in soil, corn leaves, and grain after cessation of biosolids applications

From 1974 to 1984, 543 Mg ha(-1) of biosolids were applied to portions of a land-reclamation site in Fulton County, IL. Soil organic C increased to 5.1% then decreased significantly (p < 0.01) to 3.8% following cessation of biosolids applications (1985-1997). Metal concentrations in amended soils (1995-1997) were not significantly different (p > 0.05) (Ni and Zn) or were significantly lower (p < 0.05) (6.4% for Cd and 8.4% for Cu) than concentrations from 1985-1987. For the same biosolids-amended fields, metal concentrations in corn (Zea mays L.) either remained the same (p > 0.05, grain Cu and Zn) or decreased (p < 0.05, grain Cd and Ni, leaf Cd, Cu, Ni, Zn) for plants grown in 1995-1997 compared with plants grown immediately following termination of biosolids applications (1985-1987). Biosolids application increased (p < 0.05) Cd and Zn concentrations in grain compared with unamended fields (0.01 to 0.10 mg kg(-1) for Cd and 23 to 28 mg kg(-1) for Zn) but had no effect (p > 0.05) on grain Ni concentrations. Biosolids reduced (p < 0.05) Cu concentration in grain compared with grain from unamended fields (1.9 to 1.5 mg kg(-1)). Biosolids increased (p < 0.05) Cd, Ni, and Zn concentrations in leaves compared with unamended fields (0.3 to 5.6 mg kg(-1) for Cd, 0.2 to 0.5 mg kg(-1) for Ni, and 32 to 87 mg kg(-1) for Zn), but had no significant effect (p > 0.05) on leaf Cu concentrations. Based on results from this field study, USEPA's Part 503 risk model overpredicted transfer of these metals from biosolids-amended soil to corn.     

Long-term biosolids application effects on metal concentrations in soil and bermudagrass forage

The long-term application of biosolids that periodically contained elevated metal concentrations has raised questions about potential effects on animal health. To address these concerns, we determined metal concentrations (As, Cd, Cu, Pb, Hg, Mo, Ni, Se, and Zn) in both soil and bermudagrass [Cynodon dactylon (L.) Pers.] forage from 10 fields in the following categories of biosolids application: six or more years (>6YR), less than six years (<6YR), and no applications (NS). Soil metal concentrations in all groups were similar to values reported for mineral soils in Georgia, and well below USEPA cumulative limits. Average metal concentrations in the forage were below the maximum tolerable level (MTL) for beef cattle, although two biosolids-amended fields in the >6YR group produced forage that was at or near the MTL for Cd and Mo, and one field in the <6YR group produced forage above the MTL for Cd. The Cu to Mo ratios in forage decreased with increasing time of sludge application, with the average in the >6YR group at a proposed 5:1 Cu to Mo ratio limit to protect ruminant health. Sulfur concentrations in the forage from all three groups was near the MTL of 4 g kg(-1). The study indicated that toxic levels of metals have not accumulated in the soils due to long-term biosolids application. Overall forage quality from the biosolids-amended fields was similar to that of commercially fertilized fields; however, due to the relatively high S and potential for a low Cu to Mo ratio, Cu supplements should be used to ensure ruminant health.     

A modified risk assessment to establish molybdenum standards for land application of biosolids

The USEPA standards (40 CFR Part 503) for the use or disposal of sewage sludge (biosolids) derived risk-based numerical values for Mo for the biosolids --> land --> plant --> animal pathway (Pathway 6). Following legal challenge, most Mo numerical standards were withdrawn, pending additional field-generated data using modern biosolids (Mo concentrations <75 mg kg(-1) and a reassessment of this pathway. This paper presents a reevaluation of biosolids Mo data, refinement of the risk assessment algorithms, and a reassessment of Mo-induced hypocuprosis from land application of biosolids. Forage Mo uptake coefficients (UC) are derived from field studies, many of which used modern biosolids applied to numerous soil types, with varying soil pH values, and supporting various crops. Typical cattle diet scenarios are used to calculate a diet-weighted UC value that realistically represents forage Mo exposure to cattle. Recent biosolids use data are employed to estimate the fraction of animal forage (FC) likely to be affected by biosolids applications nationally. Field data are used to estimate long-term Mo leaching and a leaching correction factor (LC) is used to adjust cumulative biosolids application limits. The modified UC and new FC and LC factors are used in a new algorithm to calculate biosolids Mo Pathway 6 risk. The resulting numerical standards for Mo are cumulative limit (RPc)=40 kg Mo ha(-1), and alternate pollutant limit (APL) = 40 mg Mo kg(-1) We regard the modifications to algorithms and parameters and calculations as conservative, and believe that the risk of Mo-induced hypocuprosis from biosolids Mo is small. Providing adequate Cu mineral supplements, standard procedure in proper herd management, would augment the conservatism of the new risk assessment.     

Adsorption of cadmium on biosolids-amended soils

Debate exists over the biosolid phase (organic or inorganic) responsible for the reduction in phytoavailable Cd in soils amended with biosolids as compared with soils amended with inorganic salts. To test the importance of these two phases, adsorption isotherms were developed for soil samples (nine biosolids-amended soils and their five companion controls) and two biosolids samples from five experimental sites with documented histories of biosolids application. Subsamples were treated with 0.7 M NaClO to remove organic carbon. Cadmium nitrate was added to both moist soil samples and their soil inorganic fractions (SIF) in a 0.01 M Ca(NO3)2 solution at three pH levels (6.5, 5.5, and 4.5), and equilibrated at 22 +/- 1 degrees C for at least 48 h. Isotherms of Cd adsorption for biosolids-amended soil were intermediate to the control soil and biosolids. Decreasing pH did not remove the difference between these isotherms, although adsorption of Cd decreased with decreasing pH level. Organic matter removal reduced Cd adsorption on all soils but had little influence on the observed difference between biosolids-amended and control soils. Thus, increased adsorption associated with biosolids application was not limited to the organic matter addition from biosolids; rather, the biosolids application also altered the adsorptive properties of the SIF. The greater affinity of the inorganic fraction of biosolids-amended soils to adsorb Cd suggests that the increased retention of Cd on biosolids-amended soils is independent of the added organic matter and of a persistent nature.     

Phosphorus forms in biosolids-amended soils and losses in runoff: effects of wastewater treatment process

Continuous addition of municipal biosolids to soils based on plant nitrogen (N) requirements can cause buildup of soil phosphorus (P) in excess of crop requirements; runoff from these soils can potentially contribute to nonpoint P pollution of surface waters. However, because biosolids are often produced using lime and/or metal salts, the potential for biosolids P to cause runoff P losses can vary with wastewater treatment plant (WWTP) process. This study was conducted to determine the effect of wastewater treatment process on the forms and amounts of P in biosolids, biosolids-amended soils, and in runoff from biosolids-amended soils. We amended two soil types with eight biosolids and a poultry litter (PL) at equal rates of total P (200 kg ha(-1); unamended soils were used as controls. All biosolids and amended soils were analyzed for various types of extractable P, inorganic P fractions, and the degree of P saturation (acid ammonium oxalate method). Amended soils were placed under a simulated rainfall and all runoff was collected and analyzed for dissolved reactive phosphorus (DRP), iron-oxide-coated filter paper strip-extractable phosphorus (FeO-P), and total phosphorus (EPA3050 P). Results showed that biosolids produced with a biological nutrient removal (BNR) process caused the highest increases in extractable soil P and runoff DRP. Alternatively, biosolids produced with iron only consistently had the lowest extractable P and caused the lowest increases in extractable soil P and runoff DRP when added to soils. Differences in soil and biosolids extractable P levels as well as P runoff losses were related to the inorganic P forms of the biosolids.     

On-farm assessment of biosolids effects on soil and crop tissue quality

Agronomic use of biosolids as a fertilizer material remains controversial in part due to public concerns regarding the potential pollution of soils, crop tissue, and ground water by excess nutrients and trace elements in biosolids. This study was designed to assess the effects of long-term commercial-scale application of biosolids on soils and crop tissue sampled from 18 production farms throughout Pennsylvania. Biosolids application rates ranged from 5 to 159 Mg ha(-1) on a dry weight basis. Soil cores and crop tissue samples from corn (Zea mays L.), soybean (Glycine spp.), alfalfa (Medicago sativa L.), orchardgrass (Dactylis spp.) hay, and/or sorghum [Sorghum bicolor (L.) Moench] were collected for three years from georeferenced locations at each farm. Samples were tested for nutrients, trace elements, and other variables. Biosolids-treated fields had more post-growing season soil NO3 and Ca and less soil K than control fields and there was some evidence that soil P concentrations were higher in treated fields. The soil concentrations of Cu, Cr, Hg, Mo, Mn, Pb, and Zn were higher in biosolids-treated fields than in control fields; however, differences were < or = 0.06 of the USEPA Part 503 cumulative pollutant loading rates (CPLRs). There were no differences in the concentrations of measured nutrients or trace elements in the crop tissue grown on treated or control fields at any time during the study. Commercial-scale biosolids application resulted in soil trace element increases that were in line with expected increases based on estimated trace element loading. Excess NO3 and apparent P buildup indicates a need to reassess biosolids nutrient management practices.     

Effect of long-term application of biosolids for land reclamation on surface water chemistry

Biosolids are known to have a potential to restore degraded land, but the long-term impacts of this practice on the environment, including water quality, still need to be evaluated. The surface water chemistry (NO3-, NH4+, and total P, Cd, Cu, and Hg) was monitored for 31 yr from 1972 to 2002 in a 6000-ha watershed at Fulton County, Illinois, where the Metropolitan Water Reclamation District of Greater Chicago was restoring the productivity of strip-mined land using biosolids. The mean cumulative loading rates during the past 31 yr were 875 dry Mg ha(-1) for 1120-ha fields in the biosolids-amended watershed and 4.3 dry Mg ha(-1) for the 670-ha fields in the control watershed. Biosolids were injected into mine spoil fields as liquid fertilizer from 1972 to 1985, and incorporated as dewatered cake from 1980 to 1996 and air-dried solids from 1987 to 2002. The mean annual loadings of nutrients and trace elements from biosolids in 1 ha were 735 kg N, 530 kg P, 4.5 kg Cd, 30.7 kg Cu, and 0.11 kg Hg in the fields of the biosolids-amended watershed, and negligible in the fields of the control watershed. Sampling of surface water was conducted monthly in the 1970s, and three times per year in the 1980s and 1990s. The water samples were collected from 12 reservoirs and 2 creeks receiving drainage from the fields in the control watershed, and 8 reservoirs and 4 creeks associated with the fields in the biosolids-amended watershed for the analysis of NO3- -N (including NO2- N), NH4+-N, and total P, Cd, Cu, and Hg. Compared to the control (0.18 mg L(-1)), surface water NO3- -N in the biosolids-amended watershed (2.23 mg L(-1)) was consistently higher; however, it was still below the Illinois limit of 10 mg L(-1) for public and food-processing water supplies. Biosolids applications had a significant effect on mean concentrations of ammonium N (0.11 mg L(-1) for control and 0.24 mg L(-1) for biosolids) and total P (0.10 mg L(-1) for control and 0.16 mg L(-1) for biosolids) in surface water. Application of biosolids did not increase the concentrations of Cd and Hg in surface water. The elevation of Cu in surface water with biosolids application only occurred in some years of the first decade, when land-applied sludges contained high concentrations of trace metals, including Cu. In fact, following the promulgation of 40 CFR Part 503, the concentrations of all three metals fell below the method detection level (MDL) in surface water for nearly all samplings. Nitrate in the surface water tends to be higher in spring, and ammonium, total P, and total Hg in summer and fall. Mean nitrate, ammonium, and total phosphorus concentrations were found to be greater in creeks than reservoirs. The results indicate that application of biosolids for land reclamation at high loading rates from 1972 to 2002, with adequate runoff and soil erosion control, had only a minor impact on surface water quality.     

Sorption and desorption of cadmium by different fractions of biosolids-amended soils

To evaluate the importance of both the inorganic and organic fractions in biosolids on Cd chemistry, a series of Cd sorption and desorption batch experiments (at pH 5.5) were conducted on different fractions of soils from a long-term field experimental site. The slope of the Cd sorption isotherm increased with rate of biosolids and was different for the different biosolids. Removal of organic carbon (OC) reduced the slope of the Cd sorption isotherm but did not account for the observed differences between biosolids-amended soils and a control soil, indicating that the increased adsorption associated with biosolids application was not limited to the increased OC from the addition of biosolids. Removal of both OC and Fe/Mn further reduced the slopes of Cd sorption isotherms and the sorption isotherm of the biosolids-amended soil was the same as that of the control, indicating both OC and Fe/Mn fractions added by the biosolids were important to the increased sorption observed for the biosolids-amended soil samples. Desorption experiments failed to remove from 60 to 90% of the sorbed Cd. This "apparent hysteresis" was higher for biosolids-amended soil than the control soil. Removal of both OC and Fe/Mn fractions was more effective in removing the observed differences between the biosolids-amended soil and the control than either alone. Results show that Cd added to biosolids-amended soil behaves differently than Cd added to soils without biosolids and support the hypothesis that the addition of Fe and Mn in the biosolids increased the retention of Cd in biosolids-amended soils.     

Levels of dioxins in soil and corn tissues after 30 years of biosolids application

Detectable levels of dioxins have been reported in biosolids, but very little information is available on the effect of long-term application of biosolids on dioxins accumulation in soil and uptake by plants. We analyzed dioxins in soil and corn tissue samples from field plots after 30 continuous applications of biosolids at 0 (Control), 16.8, and 67.2 Mg biosolids ha(-1) yr(-1) resulting in 0, 504, and 2016 Mg ha(-1) cumulative loadings of biosolids, respectively. The levels of dioxins in soil were only 79.9, 115.5, and 247.5 ng toxic equivalents (TEQs) kg(-1) in the 0, 504, and 2016 Mg biosolids ha(-1) plots, respectively. Dioxins were not detected in the corn grain, and only trace levels (6.8-7.5 ng TEQs kg(-1)) were found in the corn stover; however, these values were not statistically different between control and biosolids-amended soils. These observations suggest that although long-term application of biosolids may increase the levels of dioxins in soil, it does not affect dioxins uptake by corn.     

Fate of polydimethylsilicone in biosolids-amended field plots

This research examined the fate of polydimethylsilicones (PDMS) in agricultural test plots amended with municipal biosolids. This 4 yr field study involved addition of 0, 15, and 100 Mg ha(-1) of municipal biosolids, which contained ambient concentrations of PDMS (1272 mg kg(-1) biosolids), to corn and soybean test plots. Soil samples collected at intermittent time intervals were analyzed for soil water, soil organic C, extractable PDMS and PDMS hydrolysis products. Above normal precipitation during the field study maintained soil water levels in excess of 100 g kg(-1) for most of the testing period of 1994-1998. Under these conditions half-lives for PDMS (based on field dissipation data) ranged from 876 to 1443 d. When biosolids amended soil samples were brought into the laboratory and subjected to more rapid drying, >80% of the PDMS was transformed to lower molecular weight hydrolysis products within 20 d. No difference in relative PDMS transformation rates were evident for soils that received PDMS in the form of a biosolids amendment or directly dosed to the soil (in the absence of biosolids) indicating little if any effect of direct PDMS-biosolids interactions on PDMS transformation rates. These results support that the overriding factor controlling the fate of PDMS in field soils is the soil moisture content.     

Relationships between biosolids treatment process and soil phosphorus availability

Laws mandating phosphorus (P)-based nutrient management plans have been passed in several U.S. Mid-Atlantic states. Biosolids (sewage sludge) are frequently applied to agricultural land and in this study we evaluated how biosolids treatment processes and biosolids P tests were related to P behavior in biosolids-amended soils. Eight biosolids generated by different treatment processes, with respect to digestion and iron (Fe), aluminum (Al), and lime addition, and a poultry litter (PL), were incubated with an Elkton silt loam (fine-silty, mixed, active, mesic Typic Endoaquult) and a Suffolk sandy loam (fine-loamy, siliceous, semiactive, thermic Typic Hapludult) for 51 d. The amended soils were analyzed at 1 and 51 d for water-soluble phosphorus (WSP), iron-oxide strip--extractable phosphorus (FeO-P), Mehlich-1 P and pH. The biosolids and PL were analyzed for P, Fe, and Al by USEPA 3050 acid-peroxide digestion and acid ammonium oxalate, Mehlich-1, and Mehlich-3 extractions. Biosolids and PL amendments increased extractable P in the Suffolk sandy loam to a greater extent than in the Elkton silt loam throughout the 51 d of the incubation. The trend of extractable WSP, FeO-P, and Mehlich-1 P generally followed the pattern: [soils amended with biosolids produced without the use of Fe or Al] > [PL and biosolids produced using Fe or Al and lime] > [biosolids produced using only Fe and Al salts]. Mehlich-3 P and the molar ratio of P to [Al + Fe] by either the USEPA 3050 digestion or oxalate extraction of the biosolids were good predictors of changes in soil-extractable P following biosolids but not PL amendment. Therefore, the testing of biosolids for P availability, rather than total P, is a more appropriate tool for predicting extractable P from the biosolids-amended soils used in this study.     

Phosphorus restrictions for land application of biosolids: current status and future trends

The application of biosolids (sewage sludge) to agricultural soils provides P in excess of crop needs when applied to meet the N needs of most agronomic crops. These overapplications can result in the buildup of P in soils to values well above those needed for optimum crop yields and also may increase risk of P losses to surface and ground waters. Because of concerns regarding the influence of P on water quality in the USA, many state and federal agencies now recommend or require P-based nutrient management plans for animal manures. Similar actions are now under consideration for the land application of biosolids. We reviewed the literature on this subject and conducted a national survey to determine if states had restrictions on P levels in biosolids-amended soils. The literature review indicates that while the current N-based approach to biosolids management does result in increases of soil P, some properties of biosolids may mitigate the environmental risk to water quality associated with land application of P in biosolids. Results of the survey showed that 24 states have regulations or guidelines that can be imposed to restrict land application of biosolids based on P. Many of these states use numerical thresholds for P in biosolids-amended soils that are based on soil test phosphorus (STP) values that are much greater than the values considered to be agronomically beneficial. We suggest there is the need for a comprehensive environmental risk assessment of biosolids P. If risk assessment suggests the need for regulation of biosolids application, we suggest regulations be based on the P Site Index (PSI), which is the method being used by most states for animal manure management.     

Effect of alkaline-stabilized biosolids on alfalfa molybdenum and copper content

Agricultural utilization of biosolids poses a potential risk to ruminant animals due to transfer of Mo from biosolids to forage to the animal in amounts large enough to suppress Cu uptake by the animal. Alkaline-stabilized biosolids (ASB) must be given particular consideration in assessment of Mo risk because the high pH of these biosolids could increase Mo and decrease Cu uptake by forage legumes. In this 3-yr field experiment, ASB and ground agricultural limestone (AL) were applied based on their alkalinity at rates equivalent to 0, 0.5, 1.0, and 2.0 times the lime requirement of the soil and alfalfa (Medicago sativa L.) was grown. Alfalfa yield was similar with AL and ASB except in the second year when ASB produced larger yields, apparently due to increased B availability with ASB. Application of ASB did not detectably increase extractable soil Mo (0- to 15-cm depth), but increased alfalfa Mo uptake in all cuttings with yield-weighted uptake coefficients (UCs) of 8.07 and 7.11 following the first and second ASB applications, respectively. Although ASB increased extractable soil Cu, and alfalfa Cu content was greater with ASB than with AL, yield-weighted alfalfa Cu to Mo ratio was decreased by ASB to levels near 3. These results suggest that ASB may have a greater effect on Mo uptake and Cu to Mo ratio of forage legumes than do other biosolids. Additional research is needed to determine implications of larger Mo cumulative loading with ASB for Mo risk, particularly in the soil pH range of 7 to 8.     

ENVIRONMENTAL IMPACTS OF APPLYING MANURE,FERTILIZER, AND SEWAGE BIOSOLIDS ON A DAIRY FARM1

ABSTRACT: Farms that once spread only manures are now also applying sewage biosolids (sludge) and/or other wastes such as those from food processing. The objective of this study was to monitor environmental impacts at a dairy farm applying these materials. Fields were selected representing recent waste applications of manure (M1, M2), sewage biosolids (B1, B2), or fertilizer only control (F1, F2), although most fields had historical biosolids applications. Fields representing each treatment were not experimental replicates because of varying applications and soil characteristics. Septage and food processing wastes were also applied. Soil percolates were collected with wick lysimeters. Runoff was sampled at seven stream sites. Test field soils and alfalfa (Medicago sativa) were analyzed for trace elements. Cumulative trace metal loadings were low, at most only 1 percent of USEPA Part 503 limits. Surface soil enrichment was most evident for Mo, P, and S. Alfalfa tissue showed no trends of concern. The B2 site had the greatest percolate concentrations for 6 of 13 elements. Percolate Cu was somewhat elevated at Sites M1, M2, B2, and Fl. Percolate sodium was elevated on all M and B fields and sulfur was greatest at M2, B1, and B2. Soluble orthophosphate correlated with stream discharge during intensive monitoring of Stream Sites S1 (fertilizer) and S2 (biosolids). Peaks in S2 streamwater Mo lagged large runoff events by five days. Total streamwater export of Cu, Na, Mo, and soluble P were greater from the S2 biosolids subwatershed than from the S1 fertilizer subwatershed. Percolate concentrations exceeded corresponding streamwater concentrations in most cases.     

Effect of dissolved organic carbon on zinc solubility in incubated biosolids-amended soils

Soil organic carbon (SOC) and dissolved organic carbon (DOC) affect long-term heavy metal solubility in biosolids-amended soils, but their role needs to be further studied under Mediterranean climatic conditions. We investigated Zn solubility, as assessed by water extraction, in two typical Greek soils amended with biosolids at 0, 20, and 100 Mg ha(-1) during a 310-d incubation period. It was found that SOC decreased by nearly 30% over time in the 100 Mg ha(-1) treatment. There was evidence that DOC affected Zn solubility, because DOC increased significantly on Day 23, probably due to a flush in microbial activity, and water-extractable Zn followed the same trend. After that, both DOC and water-extractable Zn decreased back to values similar to those of the unamended soils. Although Zn solubility did not increase overall even at high biosolids application rates, this study shows that time-limited fluctuations in Zn solubility due to sudden DOC flushes, can be significant, and need to be further investigated.     

Biosolids affect soil barium in a dryland wheat agroecosystem

In December 2003, the USEPA released an amended list of 15 "candidate pollutants for exposure and hazard screening" with regard to biosolids land application, including Ba. Therefore, we decided to monitor soil Ba concentrations from a dryland wheat (Triticum aestivum L.)-fallow agroecosystem experiment. This experiment received 10 biennial biosolids applications (1982-2003) at rates from 0 to 26.8 dry Mg ha(-1) per application year. The study was conducted on a Platner loam (Aridic Paleustoll), approximately 30 km east of Brighton, CO. Total soil Ba, as measured by 4 M HNO(3), increased with increasing biosolids application rate. In the soil-extraction data from 1988 to 2003, however, we observed significant (P < 0.10) linear or exponential declines in ammonium bicarbonate-diethylenetriaminepentaacetic acid (AB-DTPA) extractable Ba concentrations as a function of increasing biosolids application rates. This was observed in 6 of 7 and 3 of 7 yr for the 0- to 20- and 20- to 60-cm soil depths, respectively. Results suggest that while total soil Ba increased as a result of biosolids application with time, the mineral form of Ba was present in forms not extractable with AB-DTPA. Scanning electron microscopy using energy dispersive spectroscopy verified soil Ba-S compounds in the soil surface, probably BaSO(4). Wet chemistry sequential extraction suggested BaCO(3) precipitation was increasing in the soil subsurface. Our research showed that biosolids application may increase total soil Ba, but soil Ba precipitates are insoluble and should not be an environmental concern in similar soils under similar climatic and management conditions.     

Utilization of biosolids during the phytoremediation of hydrocarbon-contaminated soil

Addition of anaerobically digested sewage sludge (biosolids) to soil may improve conditions for phytoremediation of petroleum hydrocarbons (PHCs) through improved soil chemical, biological, and physical properties. A 32-wk greenhouse study investigated three rates of biosolids addition (0, 13.34, and 26.68 g oven-dry biosolids kg(-1) oven-dry soil) and the presence or absence of smooth brome (Bromus inermis Leyss. cv. Carlton) plants on the removal of diesel (3.5 g kg(-1) oven-dry soil) in an industrial, sandy loam soil. Diesel PHCs were divided into two fractions based on equivalent normal straight-chain boiling point ranges (F2: nC10-nC16; F3: nC16-nC34). The addition of biosolids did not increase the extent of PHC degradation but did result in significantly greater first-order decay constants compared to unamended controls. Overall, the presence of plants did not increase the rate or extent of PHC degradation, relative to that observed in unamended, non-vegetated soils. Vegetation was, however, an important factor within the biosolids-amended soils as was observed by a greater extent of PHC degradation. Some of this decrease was attributed to plant-induced removal of biosolids components that were contributing to the F3 fraction. Overall, the low-amendment rate (13.34 g oven-dry biosolids kg(-1) oven-dry soil) was considered to be the most effective treatment because it produced the greatest overall PHC degradation rate (0.226 wk(-1) for total PHCs) and resulted in the greatest recovery of biosolids-derived N by smooth brome (26.6%).     

Phytoavailability of biosolids phosphorus

Efficient utilization of biosolids P for agronomic purposes requires accounting for differences in the phytoavailability of P in various biosolids. Greenhouse studies were conducted with a common pasture grass grown in two P-deficient soils amended with 12 biosolids and a commercial fertilizer (triple superphosphate, TSP) to quantify P uptake and to assess the relative phytoavailabilities of the P sources. Biosolids were grouped into three general categories of phytoavailability relative to TSP: high (> 75% of TSP), moderate (25-75% of TSP), and low (< 25% of TSP). Two biosolids, produced via biological phosphorus removal (BPR) processes, were in the high category, and mimicked fertilizer P with regard to P phytoavailability. Most biosolids produced by conventional wastewater and solids digestion and additional treatments like composting were in the moderate category. Also included in this category was a BPR that had been pelletized and another BPR supplemented with Al. The low category included biosolids containing greater than normal (> 50 g kg(-1)) total Fe and Al concentrations and processed to high (> 60%) solids content.     

Hybrid poplar and forest soil response to municipal and industrial by-products: a greenhouse study

Little research has been conducted in the Lake States (Minnesota, Wisconsin, and Michigan) to evaluate the effects of municipal and industrial by-product applications on the early growth of short rotation woody crops such as hybrid poplar. Anticipated shortages of harvestable-age aspen in the next decade can be alleviated and rural development can be enhanced through the application of by-products to forest soils. This study was conducted to evaluate the effects of inorganic fertilizer, boiler ash, biosolids, and the co-application of ash and biosolids application on tree growth and soil properties by measuring hybrid poplar clone NM-6 (Populus nigra L. x P. maximowiczii A. Henry) yield, nutrient uptake, and select post-harvest soil properties after 15 wk of greenhouse growth. Treatments included a control of no amendment; agricultural lime; inorganic N, P, and K; three types of boiler ash; biosolids application rates equivalent to 70, 140, 210, and 280 kg available N ha(-1); and boiler ash co-applied with biosolids. All of the by-products treatments showed biomass production that was equal to or greater than inorganic fertilizer and lime treatments. A trend of increased biomass with increasing rates of biosolids was observed. Soil P concentration increased with increasing rates of biosolids application. None of the by-products treatments resulted in plant tissue metal concentrations greater than metal concentrations of plant tissue amended with inorganic amendments. Biosolids, boiler ash, and the co-application of biosolids and boiler ash together on forest soils were as beneficial to plant growth as inorganic fertilizers.