Factors influencing formation of trihalomethanes in drinking water with special reference to Swedish conditions

The trihalomethane (THM) concentrations in drinking water are greatly affected by the disinfection methods as well as the organic content of the water. The THM formation was shown to increase considerable during 24 hours. This indicates a higher concentration of THM at the consumers' tap compared to the levels in the outgoing water from the water work. The dosage ratio between chlorine and ammonium sulphate can be used to regulate the THM concentrations. Disinfection with a relatively high dosage of chlorine dramatically increase the THM level while the equal amount of chlorine dioxide produces trace concentrations of THM only. The relatively low THM concentrations in Swedish drinking water as compared to levels found in water from for example the USA may probably depend on the low chlorine dosage practiced in Sweden.     

Trihalomethane formation during water disinfection in four water supplies in the Somes river basin in Romania

Background, aim and scope

After the discovery of chloroform in drinking water, an extensive amount of work has been dedicated to the factors influencing the formation of halogenated disinfections by-products (DBPs). The disinfection practice can vary significantly from one country to another. Whereas no disinfectant is added to many water supplies in Switzerland or no disinfectant residual is maintained in the distribution system, high disinfectant doses are applied together with high residual concentrations in the distribution system in other countries such as the USA or some southern European countries and Romania. In the present study, several treatment plants in the Somes river basin in Romania were investigated with regard to chlorine practice and DBP formation (trihalomethanes (THMs)). Laboratory kinetic studies were also performed to investigate whether there is a relationship between raw water dissolved organic matter, residual chlorine, water temperature and THM formation.

Materials and methods

Drinking water samples were collected from different sampling points in the water treatment plant (WTP) from Gilau and the corresponding distribution system in Cluj-Napoca and also from Beclean, Dej and Jibou WTPs. The water samples were collected once a month from July 2006 to November 2007 and stored in 40-mL vials closed with Teflon lined screw caps. Water samples were preserved at 4°C until analysis after sodium thiosulfate (Na₂S₂O₃) had been added to quench residual chlorine. All samples were analysed for THMs using headspace GC-ECD between 1 and 7 days after sampling. The sample (10 mL) was filled into 20-mL headspace vials and closed with a Teflon-lined screw cap. Thereafter, the samples were equilibrated in an oven at 60°C for 45 min. The headspace (1 mL) was then injected into the GC (Cyanopropylphenyl Polysiloxane column, 30 m × 53 mm, 3 μm film thickness, Thermo Finnigan, USA). The MDLs for THMs were determined from the standard deviation of eight standards at 1 μg/L. The MDLs for CHCl₃, CHBrCl₂, CHBr₂Cl and CHBr₃ were 0.3, 0.2, 0.3 and 0.6 μg/L, respectively. All kinetic laboratory studies were carried out only with water from the WTP Gilau. The experiments were conducted under two conditions: baseline conditions (pH 7, 21°C, 2.5 mg/L Cl₂) to gain information about the change of the organic matter in the raw water and seasonally variable conditions to simulate the actual process at the treatment plant and the distribution system.

Results and discussion

This study shows that the current chlorination practice in the investigated plants complies with the THM drinking water standards of the EU. The THM concentrations in all samples taken in the four treatment plants and distributions systems were below the EU drinking water standard for TTHMs of 100 μg/L. Due to the low bromide levels in the raw waters, the main THM formed in the investigated plants is chloroform. It could also be seen that the THM levels were typically lower in water supplies with groundwater as their water resource. In one plant (Dej) with a pre-ozonation step, a significantly lower (50%) THM formation during post-chlorination was observed. Laboratory chlorination experiments revealed a good correlation between chloroform formation and the consumed chlorine dose. Also, these experiments allowed a semi-quantative prediction of the chloroform formation in the distribution system of Cluj-Napoca.

Conclusions

CHCl₃ was the most important trihalomethane species observed after the chlorination of water in all of the sampled months. However, TTHM concentrations did not exceed the maximum permissible value of 100 μg/L (EU). The THM formation rates in the distribution system of Cluj-Napoca have a high seasonal variability. Kinetic laboratory experiments could be used to predict chloroform formation in the Cluj-Napoca distribution system. Furthermore, an empirical model allowed an estimation of the chloroform formation in the Gilau water treatment plant.

     

Relationships among trihalomethane formation potential, organic carbon and lake enrichment

Trihalomethanes (THMs) are potential carcinogens formed from the reaction of the disinfectant chlorine with organic matter in the source water. This study of Kansas drinking water supply lakes evaluates the relationship among THM formation potential (THMFP), organic carbon and lake trophic state (LTS). THMFP was positively correlated to organic carbon. Total THMFP and total organic carbon were positively correlated to LTS, an estimator of lake enrichment, when very turbid lakes were omitted. These very turbid lakes (due to high suspended solids concentrations) had higher than expected THMFP, based on LTS, and higher organic carbon concentrations. THM data measured in the treated drinking water were positively correlated to THMFP, total organic carbon and LTS. The levels of organic carbon that contribute to THMs are a result of lake and watershed factors related to increasing levels of enrichment and suspended sediments. These factors are controllable by appropriate management practices.     

Trihalomethane formation during water disinfection in four water supplies in the Somes river basin in Romania

Background, aim and scope  

After the discovery of chloroform in drinking water, an extensive amount of work has been dedicated to the factors influencing the formation of halogenated disinfections by-products (DBPs). The disinfection practice can vary significantly from one country to another. Whereas no disinfectant is added to many water supplies in Switzerland or no disinfectant residual is maintained in the distribution system, high disinfectant doses are applied together with high residual concentrations in the distribution system in other countries such as the USA or some southern European countries and Romania. In the present study, several treatment plants in the Somes river basin in Romania were investigated with regard to chlorine practice and DBP formation (trihalomethanes (THMs)). Laboratory kinetic studies were also performed to investigate whether there is a relationship between raw water dissolved organic matter, residual chlorine, water temperature and THM formation.     

Water purification systems: a comparative analysis based on the occurrence of disinfection by-products

Trihalomethanes (THMs) are halogenated hydrocarbons, and are by-products of the chlorination of drinking water. Most THMs are formed in drinking water when chlorine reacts with naturally occurring organic substances such as decomposing plant and animal materials. Risks for certain types of cancer are now being correlated with the presence of disinfection by-products (DBPs). The present research uses gas chromatography to analyze the presence and levels of THMs in drinking water samples from a variety of sources. These include (1) municipal drinking water from two south Florida counties; (2) two brands of bottled water; (3) untreated residential well water; and (4) municipal tap water passed through additional water purification systems. The results are summarized in a tabular format, and the compliance of each water with existing US EPA-mandated standards is examined. General conclusions from this study are that all the waters tested complied with federal regulations regarding THM levels, properly functioning home filtration units may be quite effective in further reducing DBP concentrations and, as expected, non-chlorinated waters such as bottled water and residential well water contain lower THM levels.     

Predictive model for disinfection by-product in Alexandria drinking water, northern west of Egypt

Chlorine has been utilized in the early stages of water treatment processes as disinfectant. Disinfection for drinking water reduces the risk of pathogenic infection but may pose a chemical threat to human health due to disinfection residues and their by-products (DBP) when the organic and inorganic precursors are present in water. In the last two decades, many modeling attempts have been made to predict the occurrence of DBP in drinking water. Models have been developed based on data generated in laboratory-scale and field-scale investigations. The objective of this paper is to develop a predictive model for DBP formation in the Alexandria governorate located at the northern west of Egypt based on field-scale investigations as well as laboratory-controlled experimentations. The present study showed that the correlation coefficient between trihalomethanes (THM) predicted and THM measured was R ²?=?0.88 and the minimum deviation percentage between THM predicted and THM measured was 0.8 %, the maximum deviation percentage was 89.3 %, and the average deviation was 17.8 %, while the correlation coefficient between dichloroacetic acid (DCAA) predicted and DCAA measured was R ²?=?0.98 and the minimum deviation percentage between DCAA predicted and DCAA measured was 1.3 %, the maximum deviation percentage was 47.2 %, and the average deviation was 16.6 %. In addition, the correlation coefficient between trichloroacetic acid (TCAA) predicted and TCAA measured was R ²?=?0.98 and the minimum deviation percentage between TCAA predicted and TCAA measured was 4.9 %, the maximum deviation percentage was 43.0 %, and the average deviation was 16.0 %.     

Development of a model for predicting trihalomethanes propagation in water distribution systems

The rate of Trihalomethanes (THM) formation was experimentally observed to be first-order with respect to chlorine, and first-order with respect to humic acid precursors, and the overall reaction order was second-order. THM formation rate expression was formulated as a function of the concentration of THM Formation Potential (THMFP), residual chlorine concentration, reaction time and reaction temperature. A model is developed to estimate THM in water distribution systems. Since the calculated results are close to the measured values in the distribution system, it is suggested that this model is applicable to actual water distribution systems.     

Investigation of the behaviour of haloketones in water samples

The behaviour of the haloketones (HKs) 1,1-Dichloropropanone (1,1-DCP), 1,1,1-Trichloropropanone (1,1,1-TCP) and 1,3-Dichloropropanone (1,3-DCP) in ultrapure water solutions and in fortified drinking water samples was investigated. Their concentrations were determined at regular time intervals by the use of a gas chromatography-electron capture detector (GC-ECD) method. Two different temperatures were studied. The results have shown that HKs decompose both in ultrapure water solutions and in drinking water samples. The decomposition rates are higher in the drinking water samples, especially at higher temperature. 1,1,1-TCP is the compound which decomposes fastest followed by 1,3-DCP and 1,1-DCP. Chloroform was formed both in the ultrapure water solutions and in the drinking water samples, probably due to the decomposition of 1,1,1-TCP. In the drinking water samples, formation of chloral hydrate was also observed.     

Distribution of polycyclic aromatic hydrocarbons in surface water and sediment near a drinking water reservoir in Northeastern China

The levels of polycyclic aromatic hydrocarbons (PAHs) in the water and the sediment samples collected near the Mopanshan Reservoir—the most important drinking water resource of Harbin City in Northeast China—were examined. A total of 16 PAHs were concurrently identified and quantified in the three water bodies tested (Lalin River, Mangniu River, and Mopanshan Reservoir) and in the Mopanshan drinking water treatment plant during the high- and low water periods. The total PAH concentrations in the water and sediment samples ranged from 122.7 to 639.8 ng/L and from 89.1 to 749.0 ng/g dry weight, respectively. Similar spatial and temporal trends were also found for both samples. The lowest Σ₁₆PAH concentration of the Mopanshan Reservoir was obtained during the high water period; by contrast, the Lalin River had the highest concentration during the low water period. The PAH profiles resembling the three water bodies, with high percentages of low-molecular weight PAHs and dominated by two- to three-ring PAHs (78.4 to 89.0 %). Two of the molecular indices used reflected the possible PAH sources, indicating the main input from coal combustion, especially during the low water period. The conventional drinking water treatment operations resulted in a 20.7 to 67.0 % decrease in the different-ringed PAHs in the Mopanshan-treated drinking water. These findings indicate that human activities negatively affect the drinking water resource. Without the obvious removal of the PAHs in the waterworks, drinking water poses certain potential health risks to people.     

The role of wastewater treatment in protecting water supplies against emerging pathogens.

Traditionally, regulators, dischargers, and even water suppliers believed that wastewater discharge meeting the levels of 200 cfu/ 100 mL of fecal coliforms in wastewater effluent was sufficient to protect against downstream microbial effects. However, these beliefs are now being challenged by emerging pathogens that are resistant to standard water and wastewater treatment processes, exhibit extended survival periods in the environment, can adversely affect sensitive subpopulations, and require extremely low doses for human infection. Based on this new information, it is estimated that discharges of emerging pathogens from conventional wastewater treatment plants as far as 160 km upstream and cumulative amounts of wastewater discharge ranging from 2 to 20 ML/d have the potential to reach a water supply intake in a viable state at significant concentrations that could exceed regulatory limits for drinking water supplies, increase endemic risk from drinking water, and/or require additional drinking water treatment. Wastewater dischargers may be able mitigate this potential effect and achieve upwards of 6 log combined removal and inactivation of emerging pathogens to mitigate drinking water effects by using alternative treatment processes, such as filtration or UV light disinfection, or optimizing these processes based on site-specific conditions.     

Fate of disinfection by-products in groundwater during aquifer storage and recovery with reclaimed water

Knowledge on the behaviour of disinfection by-products (DBPs) during aquifer storage and recovery (ASR) is limited even though this can be an important consideration where recovered waters are used for potable purposes. A reclaimed water ASR trial in an anoxic aquifer in South Australia has provided some of the first quantitative information at field-scale on the fate and transport of trihalomethanes (THMs) and haloacetic acids (HAAs). The results revealed that THM half-lives varied from <1 to 65 days, with persistence of chloroform being highest and bromoform lowest. HAA attenuation was rapid (<1 day). Rates of THM attenuation were shown to be highly dependent on the geochemical environment as evidenced by the 2-5 fold reduction in half-lives at the ASR well which became methanogenic during the storage phase of the trial, as compared to an observation well situated 4 m away, which remained nitrate-reducing. These findings agree with previous laboratory-based studies which also show persistence declining with increased bromination of THMs and reducing redox conditions. Modelling suggests that the chlorinated injectant has sufficient residual chlorine and natural organic matter for substantial increases in THMs to occur within the aquifer, however this is masked in some of the field observations due to concurrent attenuation, particularly for the more rapidly attenuated brominated compounds. The model is based on data taken from water distribution systems and may not be representative for ASR since bromide and ammonia concentrations in the injected water and the possible role of organic carbon in the aquifer were not taken into consideration. During the storage phase DBP formation potentials were reduced as a result of the removal of precursor material despite an increase in the THM formation potential per unit weight of total organic carbon. This suggests that water quality improvements with respect to THMs and HAAs can be achieved through ASR in anoxic aquifers.     

Fate of disinfection by-products in groundwater during aquifer storage and recovery with reclaimed water

Knowledge on the behaviour of disinfection by-products (DBPs) during aquifer storage and recovery (ASR) is limited even though this can be an important consideration where recovered waters are used for potable purposes. A reclaimed water ASR trial in an anoxic aquifer in South Australia has provided some of the first quantitative information at field-scale on the fate and transport of trihalomethanes (THMs) and haloacetic acids (HAAs). The results revealed that THM half-lives varied from <1 to 65 days, with persistence of chloroform being highest and bromoform lowest. HAA attenuation was rapid (<1 day). Rates of THM attenuation were shown to be highly dependent on the geochemical environment as evidenced by the 2-5 fold reduction in half-lives at the ASR well which became methanogenic during the storage phase of the trial, as compared to an observation well situated 4 m away, which remained nitrate-reducing. These findings agree with previous laboratory-based studies which also show persistence declining with increased bromination of THMs and reducing redox conditions. Modelling suggests that the chlorinated injectant has sufficient residual chlorine and natural organic matter for substantial increases in THMs to occur within the aquifer, however this is masked in some of the field observations due to concurrent attenuation, particularly for the more rapidly attenuated brominated compounds. The model is based on data taken from water distribution systems and may not be representative for ASR since bromide and ammonia concentrations in the injected water and the possible role of organic carbon in the aquifer were not taken into consideration. During the storage phase DBP formation potentials were reduced as a result of the removal of precursor material despite an increase in the THM formation potential per unit weight of total organic carbon. This suggests that water quality improvements with respect to THMs and HAAs can be achieved through ASR in anoxic aquifers.     

Occurrence of THMs and HAAs in experimental chlorinated waters of the Quebec City area (Canada)

Haloacetic acids (HAAs) and trihalomethanes (THMs) were generated in bench-scale chlorination experiments using treated waters (prior to final chlorination) of the three major drinking water utilities of the Quebec City area. The purpose was to investigate the formation and occurrence of these chlorination by-products (CBPs) on a seasonal basis. Data for HAAs, THMs and other physico-chemical parameters were produced through a six-month sampling program with variable conditions of water quality, water temperature, applied chlorine dose and reaction time. In waters from the three utilities, chloroform (THM specie), dichloroacetic and trichloroacetic acid (HAA species) were the most prevalent compounds due to the low concentrations of bromide in the utilities' raw waters. Significant differences in CBP occurrence were noted between the three utilities' chlorinated waters, mainly due to the type of disinfectant applied to raw water. The use of pre-ozonation, as opposed to pre-chlorination (or direct chlorination) in one of the utilities appears to be the major factor contributing to that utility's potential for compliance with current THM and future HAA standards. Seasonal variations in THMs and HAAs were mainly associated with variations in organic precursors and to changes in water temperature (two parameters which vary widely on a seasonal basis in surface waters of southern Quebec), with CBP occurrence at its highest in spring. Statistical correlations between HAAs and THMs were moderate and only temperature appeared to affect the preponderance of one CBP or the other. Finally, a regression analysis was carried out aimed at associating each CBP to water quality and the experimental parameters. Thanks to their predictive ability, multivariate models seem to be the tools with the best potential for decision-making purposes.     

Nitrogen species in drinking water indicate potential exposure pathway for Balkan Endemic Nephropathy

This study explored two hypotheses relating elevated concentrations of nitrogen species in drinking water and the disease Balkan Endemic Nephropathy (BEN). Drinking water samples were collected from a variety of water supplies in both endemic and non-endemic villages in the Vratza and Montana districts of Bulgaria. The majority of well water samples exceeded US drinking water standards for nitrate + nitrite. No statistically significant difference was observed for any of the nitrogen species between villages classified as endemic and non-endemic. Other constituents (sodium, potassium and chloride) known to be indicators of anthropogenic pollution were also found at elevated concentrations and all followed the order wells > springs > taps. This ordering coincides with the proximity of human influences to the water sources. Our results clearly establish an exposure pathway between anthropogenic activity and drinking water supplies, suggesting that the causative agent for BEN could result from surface contamination.     

Metal contamination of drinking water from corrosion of distribution pipes

The objectives of this study were to evaluate metal contamination of drinking water resulting from the corrosion of distribution pipes and its significance to human health. A community in Dhahran, which is served from its own desalination facilities, was chosen for this study. About 150 drinking water samples were collected and analyzed for metal concentrations using an inductively coupled argon plasma analyzer. It was found that copper, iron and zinc in the drinking water increased during its transportation from the desalination plant to the consumers. This increase was related to the length and material of distribution pipes. Concentrations of copper and zinc were increased during overnight storage of water in the appliances. Metal concentrations found in this study are discussed with reference to human health.     

Methyl tert-butyl ether (MTBE) in finished drinking water in Germany

In the present study 83 finished drinking water samples from 50 cities in Germany were analyzed for methyl tert-butyl ether (MTBE) content with a detection limit of 10 ng/L. The detection frequency was 46% and the concentrations ranged between 17 and 712 ng/L. Highest concentrations were found in the community water systems (CWSs) of Leuna and Spergau in Saxony-Anhalt. These CWSs are supplied with water possibly affected by MTBE contaminated groundwater. MTBE was detected at concentrations lower than 100 ng/L in drinking water supplied by CWSs using bank filtered water from Rhine and Main Rivers. The results from Leuna and Spergau show that large groundwater contaminations in the vicinity of CWSs pose the highest risk for MTBE contamination in drinking water. CWSs using bank filtered water from Rhine and Main Rivers are susceptible to low MTBE contaminations in finished drinking water. All measured MTBE concentrations were below proposed limit values for drinking water.     

Carbamazepine and diclofenac: removal in wastewater treatment plants and occurrence in water bodies

In the aquatic environment, pharmaceuticals have been widely found. Among them, carbamazepine and diclofenac were detected at the highest frequency. To evaluate the worldwide environmental impacts of both drugs, their global consumption volumes are estimated, based on the dose per capita. The metabolites of these pharmaceuticals are also of environmental concerns, especially trans-10,11-dihydro-10,11- dihydroxycarbamazepine (CBZ-diol) which probably has a similar concentration in water bodies to that of its parent drug. The removal efficiencies and mechanisms of both drugs in the wastewater treatment plants (WWTPs) are discussed with the actual state of knowledge. The occurrences of both drugs are examined in various water bodies including WWTP effluents, surface waters, groundwater and drinking water. Their chemical, physical and pharmacological properties are also addressed in context, which can largely influence their environmental behaviors. The ecotoxicological studies of both drugs imply that they do not easily cause acute toxic effects at their environmental concentrations. However their chronic effects need cautious attention.     

Nano-silver in drinking water and drinking water sources: stability and influences on disinfection by-product formation

Nano-silver is increasingly used in consumer products from washing machines and refrigerators to devices marketed for the disinfection of drinking water or recreational water. The nano-silver in these products may be released, ending up in surface water bodies which may be used as drinking water sources. Little information is available about the stability of the nano-silver in sources of drinking water, its fate during drinking water disinfection processes, and its interaction with disinfection agents and disinfection by-products (DBPs). This study aims to investigate the stability of nano-silver in drinking water sources and in the finished drinking water when chlorine and chloramines are used for disinfection and to observe changes in the composition of DBPs formed when nano-silver is present in the source water. A dispersion of nano-silver particles (10 nm; PVP-coated) was used to spike untreated Ottawa River water, treated Ottawa River water, organic-free water, and a groundwater at concentrations of 5 mg/L. The diluted dispersions were kept under stirred and non-stirred conditions for up to 9 months and analyzed weekly using UV absorption to assess the stability of the nano-silver particles. In a separate experiment, Ottawa River water containing nano-silver particles (at 0.1 and 1 mg/L concentration, respectively) was disinfected by adding sodium hypochlorite (a chlorinating agent) in sufficient amounts to maintain a free chlorine residual of approximately 0.4 mg/L after 24 h. The disinfected drinking water was then quenched with ascorbic acid and analyzed for 34 neutral DBPs (trihalomethanes, haloacetonitriles, haloacetaldehydes, 1,1 dichloro-2-propanone, 1,1,1 trichloro-2-propanone, chloropicrin, and cyanogen chloride). The results were compared to the profile of DBPs obtained under the same conditions in the absence of nano-silver and in the presence of an equivalent concentration of Ag⁺ ions (as AgNO₃). The stability of the nano-silver dispersions in untreated Ottawa River water, with a dissolved organic carbon concentration of 6 mg/L, was significantly higher than the stability of the nano-silver dispersions in distilled, organic-free water. Nano-silver particles suspended in the groundwater agglomerated and were quickly and quantitatively removed from the solution. Our data confirm previous observations that natural dissolved organic matter stabilizes nano-silver particles, while the high-ionic strength of groundwater appears to favor their agglomeration and precipitation. As expected, nano-silver was not stable in Ottawa River water through the chlorination process, but survived for many days when added to the Ottawa River water after treatment with chlorine or chloramines. Stirring appeared to have minimal effect on nano-silver stability in untreated and treated Ottawa River water. The profile of DBPs formed in the presence of nAg differed significantly from the profile of DBPs formed in the absence of nAg only at the 1 mg/L nAg concentration. The differences observed consisted mainly in reduced formation of some brominated DBPs and a small increase in the formation of cyanogen chloride. The reduced formation of brominated congeners may be explained by the decrease in available bromide due to the presence of Ag⁺ ions. It should be noted that a concentration of 1 mg/L is significantly higher than nAg concentrations that would be expected to be present in surface waters, but these results could be significant for the disinfection of some wastewaters with comparably high nano-silver concentrations.     

饮用水消毒副产物研究状况

本文介绍了饮用水中消毒副产物的研究状况。其中重点介绍了饮用水的消毒方式及四类消毒副产物的产生、浓度、存在形态及影响因素等。简单介绍了饮用水中消毒副产物的采集、前处理方法及污染控制对策等     

Contamination status of arsenic and other trace elements in drinking water and residents from Tarkwa, a historic mining township in Ghana

This study was conducted to assess the contamination status of 22 trace elements, especially As in water and residents in Tarkwa, a historic mining town in Ghana. Drinking water and human urine samples were collected from Tarkwa in addition to control samples taken from Accra, the capital of Ghana in March, 2004. Concentrations of As and Mn in some drinking water samples from Tarkwa were found above the WHO drinking water guidelines posing a potential health risk for the people. A potential health risk of As and Mn is a concern for the people consuming the contaminated water in this area. No significant difference of As concentrations in human urine between mining town (Tarkwa) and control site (Accra) was observed. Although As concentrations in drinking water in Tarkwa were low, urinary As levels were comparable to those reported in highly As-affected areas in the world. These results suggest the presence of other sources of As contamination in Ghana. This is the first study on multi-elemental contamination in drinking water and human from a mining town in Ghana.