大气污染计算的简易公式

模拟由污染源排放的污染物对其周围地区的大气污染程度,已经提出许多计算公式,如高斯模式,萨顿扩散模式,以及针对不同排放方式的点源扩散公式和面源扩散公式等。但这些公式在使用中,由于污染源的情况千差万别,往往与模型相差甚多;此外,这些公式中所需要的气象参数,如大气稳定度和空气的湍流等的准确确定十分困难,也直接影响模型的计算精度。特别当污染源以多种方式排放时,选择合适的源强参数就更为困难。 本文提出了只需要源点浓度、风向、风速和距离的浓度衰减公式。该公式在对我市包钢氟污染的计算中,对二十一个点的监测数据进行计算,取得满意的结果。     

网格监测统计积分模式的推导与应用

把大气污染物的空间分布看成是连续变化的超曲面,采用积分法推导网格监测点位均值的积分模式,并由此推导监测范围内污染物总量模式。利用丹东市环境空气SO2被动扩散网格监测数据,采用此模式计算其趋势值和均值。     

基于MapInfo的大气污染物复合多源模式研究及应用

研究了在MapInfp环境下的大气污染物复合多源模式,利用MapBasic编制了不同风向条件下的污染源坐标转换程序,同时利用Surfer软件绘制了污染物浓度等值线,并在MapInfo中与基础底图叠加。通过对某工业区SO2长期平均浓度的预测,证明复合多源模式在环境影响评价中具有很好的应用价值。     

点源扩散大气预测软件

建设项目的点源扩散大气预测软件,包括了<环境影响评价技术导则-大气环境>第三级评价有风时,静风和小风扩散模式;最大地面浓度Cm及其距排气筒的距离Xm模式;烟气抬升公式以及等值线点位值的计算功能.该软件运算快速、简便、准确.     

小风和静风状态下连续体源大气扩散模式的理论推导

以小风和静风状态下连续点源的大气扩散模式为基础,采用与体源烟团的初始分布尺度相当的初始时间修正其扩散参数公式中的运行时间,从理论上导出了小风和静风状态下连续体源的大气扩散模式。该模式与现有的大气扩散模式体系完全相容,可以方便地应用于小风和静风状态下连续体源引起的地面浓度的预测计算。     

水泥厂大气污染物健康风险评价初探

根据大气污染物的环境行为,沿着污染物排放-迁移转化-人体吸收这条途径,提出了以致残调整生命年为最终评价指标的大气污染物人体健康风险定量评价方法.对广东某水泥厂实例分析说明,水泥生产过程排放的各种大气污染物中,NOx的人体健康风险最大,占水泥生产过程所有大气污染物健康风险的43.9%,SO2的人体健康风险最小.     

洞庭湖区一次重度空气污染过程成因分析

利用AQI和PM_(2. 5)质量浓度、地面气象要素、NCEP、ERSST_V3、GBL等资料,对2016年12月29日至2017年1月5日洞庭湖区一次重度空气污染过程成因进行了分析。结果表明,静稳天气形势下的累积效应和本地持续升温、降压、增湿、小风导致污染物浓度不断增加。本地风速与雨量对污染物浓度产生显著影响。降温前风速明显加大,有利于污染物快速扩散。湿度增加有利于污染物吸湿性增长,但高湿易引起降水有利于污染物的湿清除。此次重度空气污染过程中大气稳定度为中性或稳定,14:00混合层高度逐渐降低且重度空气污染日降至100 m以下。污染物空间分布与主导风向和污染通道密切相关。气流后向轨迹分析表明,洞庭湖区各地气流来源和影响路径差异明显,且存在大范围区域性同步污染现象。北方外来污染源是洞庭湖区重要的污染面源,本地工业污染排放点源和地理条件也是洞庭湖区空气污染物空间分布差异的重要因素。     

用后向空气轨迹方法对胶州湾主要大气污染物分布的分析

采用青岛崂山点位2005-2009年的大气监测数据,利用HYSPLIT4.8模式和象限分析方法,计算出污染物的方位贡献情况,判断出胶州湾大气污染物的传输路径主要为北、西北和西部路径,S02、N02和PM10在北部和西北部象限的5年平均贡献率分别为25.32％和28.21％、21.16％和21.53％以及20.25％和22.83％,这与胶州湾东方和东南方为海洋、北方和西北方为工业城市有关.通过个例分析得出的传输路径与象限分析的结果一致.另一方面,胶州湾地区的主要污染物在过去5年中的年均值浓度变化显示,SD2浓度呈下降趋势,NO2浓度呈上升趋势,PM10浓度变化趋势不明显.为调查青岛市和周边5个省污染物排放水平对胶州湾污染物分布的影响,分析了2005-2009年的相关环境统计数据,SO,的排放量下降,燃料煤消耗量、氮氧化物排放量以及机动车数量逐年升高可能是导致胶州湾地区污染物浓度变化的原因.     

火力发电行业主要气态污染物排放量计算方法研究

针对目前我国火力发电行业气态污染物排放量计算方法使用混乱的情况,根据欧盟《空气污染物排放清单指南》和美国《空气污染物排放因子汇编》,介绍了火电行业主要气态污染物排放量的实际测量及理论计算方法。提出我国火电行业应根据实际情况,选择实际测量、排放因子或经验公式等方法计算污染物排放量;使用排放因子方法计算SO2排放量时,应开展S元素转化率的研究;火电厂应增加燃料中N元素的分析,以利于NOx排放量的准确估算。     

边界层顶垂直速度对大气污染物地面浓度的影响

本文把地形、地转涡度及埃克曼抽吸作用共同引起的垂直运动通过大气污染物的平流扩散方程,引入到大气扩散模式中来.并通过实例计算了地面轴线浓度及其最大地面浓度距离后发现:在有些情况下,这些要素引起的垂直运动对大气污染物的地面浓度影响是重要的.     

Topsoil and Housedust Metal Concentrations in the Vicinity of a Lead Battery Manufacturing Plant

The aim of the study was to determine the extent of heavy metal pollution in the vicinity of a lead battery manufacturing plant in the Czech Republic, both in the general environment and within homes. Topsoils (0–5 cm) were sampled from 100 sites along 4 transects which crossed the battery factory, the town centre and outlying rural areas. Housedust samples were collected from 15 plant-workers' homes and 15 non plant-workers' homes located at various distances from the factory. Samples were analysed for levels of Pb, Zn, Cd, Cu, As and Sb, using ICP-AES. Soil concentrations of Pb, Cd, As and Sb peaked at the perimeter fence of the battery factory with Pb levels of up to 12 650 g g> ^-1. Concentrations of these metals decreased exponentially within 500 m of the plant. Whilst the battery factory does appear to be a source of all the metals with the exception of Zn, emissions do not appear to be transported to any great extent over distances of more than 0.5 km. Topsoil and housedust concentrations of Pb, Zn, Cd, Cu, As and Sb in the general Mlada Boleslav area do not appear to be significantly different from those recorded in a large scale survey of urban soils in the United Kingdom. A comparison of housedust Pb concentrations in homes of plant workers and non-plant workers suggests that there may be a small input of Pb into the home environment by battery plant employees.     

微波消解-原子吸收光度法测定土壤中铜锌铅镉镍铬

用微波消解－原子吸收光度法测定土壤中铜，锌，铅，镉，镍和铬。通过硝酸－氢氟酸－过氧化氢体系消解液对土壤样品消解，选择出微波最佳消解条件。对硝酸－盐酸－过氧化氢体系消解液和硝酸－氢氟酸－过氧化氢体系消解液进行消解对比试验，发现前者不能将土壤样品完全消解，后者能将样品消解完全，但需将消解液中剩余的酸赶尽，否则测定结果将明显偏低。微波消解土壤与传统电热消解相比，操作简便快速，可提高工作效率。     

An Overview of Contaminant-Related Issues Identified by Monitoring in San Francisco Bay

The San Francisco Estuary Regional Monitoring Program for Trace Substances (RMP) began in 1993 and is sponsored by 74 local, state, and federal agencies and companies through their discharge or Bay use permits. The RMP monitors water, sediment, toxicity, and bivalve bioaccumulation at 25 sites in the Bay that are considered to represent "background" conditions. Several major environmental issues have been identified by the RMP. Polychlorinated biphenyls and mercury were often above water quality guidelines, and often occurred in fish tissues above U.S. Environmental Protection Agency (U.S. EPA) screening values. Concentrations do not appear to be decreasing, suggesting continuing inputs. Episodes of aquatic toxicity often occurred following runoff events that transport contaminants into the Bay from urbanized and agricultural portions of the watershed. Sediment toxicity occurred throughout the Bay, and has been correlated with concentrations of specific contaminants (chlordanes, polynuclear aromatic hydrocarbons) at some locations; mixtures of contaminants were probably also important. Since the RMP does not monitor all ecosystem components, assessments of the overall condition of the Bay cannot be made. However, in terms of contamination, the RMP samples suggest that the South Bay, and North Bay sites are moderately contaminated.     

Biomagnification factors (fish to Osprey eggs from Willamette River,Oregon, U.S.A.) for PCDDs,PCDFs, PCBs and OC pesticides

A migratory population of 78 pairs of Osprey (Pandion haliaetus) nesting along the Willamette River in westernOregon was studied in 1993. The study was designed to determinecontaminant concentrations in eggs, contaminant concentrationsin fish species predominant in the Ospreys diet, andBiomagnification Factors (BMFs) of contaminants from fish specieseaten to Osprey eggs. Ten Osprey eggs and 25 composite samplesof fish (3 species) were used to evaluate organochlorine (OC)pesticides, polychlorinated biphenyls (PCBs), polychlorinateddibenzo-p-dioxins (PCDDs), and polychlorinated dibenzofurans(PCDFs). Mercury was also analyzed in fish. Geometric meanresidues in Osprey eggs were judged low, e.g., DDE 2.3 g g^-1 wet weight (ww), PCBs 0.69 g g^-1, 2,3,7,8-TCDD 2.3 ng kg^-1, and generally well below known threshold values for adverse effects on productivity, and the population was increasing. Osprey egg residue data presentedby River Mile (RM) are discussed, e.g., higher PCDDs were generally found immediately downstream of paper mills and eggsfrom the Willamette River had significantly elevated PCBs and PCDDs compared to reference eggs collected nearby in the CascadeMountains. Prey remains at nest sites indicated that the Largescale Sucker (Catostomus macrocheilus) and NorthernPikeminnow (Ptychocheilus oregonensis) accounted for an estimated 90.1% of the biomass in the Osprey diet, and composite samples of these two species were collected from different sampling sites throughout the study area for contaminant analyses. With the large percentage of the fishbiomass in the Osprey diet sampled for contaminants (and fisheaten by Ospreys similar in size to those chemically analyzed),and fish contaminant concentrations weighted by biomass intake, a mean BMF was estimated from fish to Osprey eggs for the largeseries of contaminants. BMFs ranged from no biomagnification(0.42) for 2,3,7,8-TCDF to 174 for OCDD. Our findings for themigratory Osprey were compared to BMFs for the resident HerringGull (Larus argentatus), and differences are discussed. Webelieve a BMF approach provides some basic understanding ofrelationships between contaminant burdens in prey species offish-eating birds and contaminants incorporated into their eggs,and may prove useful in understanding sources of contaminants inmigratory species although additional studies are needed.     

The Draft of the New German Guideline VDI 3782/8 to Model Automobile Exhaust Dispersion

The draft of the German guideline to calculate automobile exhaust dispersion is explained. It contains a two-stage-system: For first quick estimates the guideline contains the simple models MLuS and STREET. In case these models are not applicable or their results shows concentration levels close to the air quality standards, the more complex models PROKAS_V and MISKAM are recommended. PROKAS_V is a Gaussian plume model, MISKAM is a 3-dimensional microscale non hydrostatic flow model for built-up areas with an Eulerian dispersion model. The guideline comprises cases in rural areas without or with few adjacent buildings as well as urban areas with buildings near the roads. The contribution gives information about the models, typical results and some of the problems showing up presently.     

Hydrocarbon Utilization in Yeast Isolates Found to Grow in Association with Petroleum in a Polluted Ultisol of Midwestern Nigeria

The population counts of hydrocarbon-utilising yeasts weremonitored at six sampling stations in the Benin City municipalarea over a four-week period. Although the population countswere relatively constant in each locality, the highest countsoccurred in areas heavily polluted by domestic and industrialeffluents. A total of thirty-five hydrocarbon-degrading yeastswere isolated from soil at the sampling stations usingn-hexadecane as sole carbon source. The isolates were identifiedas belonging to the genera Candida (27 strains), Endomycopsis (4 strains). All the organisms grew on long-chainn-alkane, kerosene, diesel oil and crude oil but failed to growon short-chain n-alkane, aromatic and alicyclic hydrocarbons.Measurement of growth attributes of the isolates usingn-hexadecane, diesel oil and crude oil as substrates showed thatthe Candida species were better utilizers of hydrocarbonsubstrates relative to Endomycopsis and Schizosaccharomyces species.     

Hydrologic–Economic Model for Managing Irrigation Intensity in Irrigation Areas under Watertable and Soil Salinity Targets

This paper gives mathematical details and sample applications of SWAGMAN Farm (SWAGMAN, Salt Water and Groundwater Management), a farm-scale hydrologic economic model that integrates agronomic, climatic, irrigation, hydrogeological and economic aspects of irrigated agriculture. The model is capable of determining optimum mix of land use to keep watertable and soil salinity within acceptable limits while maximising the economic returns. Alternatively, the model can simulate water and salt balance and economics of a given cropping preference. Web-based and Geographic Information Systems versions of the model are available for integration with the environmental reporting systems of the irrigation areas.     

火焰原子吸收光谱法测定苏州开发区26种蔬菜中铜锌铁锰镍

用火焰原子吸收光谱法测定了苏州开发区26种蔬菜中的铜、锌、铁、锰和镍的含量。蔬菜样品用硝酸高氯酸混合酸进行消解。4次测定值的相对标准差<5%,加标回收率在92%～107%之间。26种蔬菜中铜、锌、铁、锰、镍的含量基本均在世贸组织规定的范围内。     

Cyanobacterial Flora from Polluted Marine Shores

Citation of cyanobacterial cultures from the shores of south west coast of Gujarat, India and their relationship with sea water quality, influenced by extensive pollutant runoff is reported in this study. Intensity of pollution was evaluated by physico-chemical analysis of water. Higher load of suspended solids (60–1000 mg l⁻¹) and nutrients (PO₄ ⁻P: 1.3–4 μmole l⁻¹ and NO₃ ⁻N: 12.5–17.8 μmole l⁻¹) were persistent throughout the analysis. Community structure is seen to be influenced by such persistent pollution. Twenty nine cyanobacterial species were isolated belonging to 9 genera of 4 families, with an elevated occurrence of Oscillatoria and Lyngbya species. No heterocystous cyanobacteria were isolated throughout the study.     

Using Multiple Taxonomic Groups to Index the Ecological Condition of Lakes

Biological indicators of communitiestypically reflect a common environmental signalreflecting the general condition of the ecosystem, as well asindividual signals by indicators differentiallysensitive to particular environmental conditions. Wedescribe here a method of integrating and interpretingsuch indicators from 19 New England lakes for fivetaxonomic groups (diatoms, benthos, zooplankton, fish,and birds). Our approach provides a systematicstandardized way to integrate multiple metrics fromdifferent taxonomic groups by addressing four elementscrucial to analyzing data from multiple indicators: covariate control, re-scaling of data, standardizing the sign of responses, and dimensional reduction. We evaluated the biologicalmetrics against individual environmental stressors andagainst multivariate physicochemical metricscharacterizing general anthropogenic stress among thelakes. The method detected a response to variationin the gross environmental condition of the lakes thatwas correlated across taxa and metrics. In addition,a differential response to near shore conditions wasdemonstrated for fish. The success of the approach inthis study lends support to its general application toecological monitoring involving complex data sets.