Metal-mediated chlorinated dibenzo-p-dioxin (CDD) and dibenzofuran (CDF) formation from phenols

Heterogeneous formation of chlorinated dibenzo-p-dioxins (CDDs) and dibenzofurans (CDFs) on CuCl2 from three phenols without ortho chlorine and one phenol with two ortho chlorines was studied in a flow reactor over a temperature range of 325-450 degrees C. Heated nitrogen gas streams containing 8% oxygen, 1.5% benzene vapor, and equal amounts of phenol, 3-chlorophenol, 3,4-dichlorophenol and 2,4,6-trichlorophenol vapor (700 ppmv, each) were passed through a 1 g particle bed of silica and 0.5% (Cu mass) CuCl2. Maximum product yields of greater than 1.4% phenol conversion to CDD and 5.7% phenol conversion to CDF were observed between 400 and 450 degrees C. CDDs formed with loss of one chlorine atom were favored. While total CDD/F yield varied with temperature, CDD/F homologue and isomer distributions did not vary significantly with temperature. Based on the results of experiments with single phenol precursors, phenol precursors could be assigned to all PCDD/F products. Of the chlorinated phenols without ortho chlorine that were studied, 3,4-dichlorophenol was found to have the greatest propensity to form CDFs.     

Continuing atmospheric studies of chlorinated dibenzofurans and dioxins in New York State

CDFs and CDDs were detected in Niagara Falls air samples with total concentrations ranging from 0.07 to 53 pg/m³. The highest concentrations were found on days when the wind direction was from a nearby point source. Average CDF/CDD background concentrations were calculated.     

The distribution of polychlorinated dibenzo-p-dioxins and dibenzofurans in Jackfish Bay, Lake Superior, in relation to a kraft pulp mill effluent

Samples of whole effluent and effluent suspended solids from a kraft pulp mill and sediments and biota from Jackfish Bay, Lake Superior were analyzed for polychlorinated dibenzo-p-dioxins (CDDs) and dibenzofurans (CDFs). Tetra-CDFs (4CDF) were consistently detected in whole effluent at levels ranging between 0.3 and 1.3 ng/L. Effluent suspended solids also contained 4CDFs as well as traces of 4CDD, 5CDF, 8CDF and 8CDD. The horizontal sediment distribution suggests that the effluent was the only active source of 4CDF in the area but that 8CDD originated from a more general source such as the atmosphere. An abrupt appearance of 4CDF in the more recent sections of a core profile taken in the bay suggests that an operational change at the pulp mill resulted in the formation of 4CDFs in the mill effluent some time after 1973. Moderate values of 4CDF and low values of 4CDD were found in samples of the shrimp confirming the presence of an active source of 4CDF in Jackfish Bay.     

“Shorthand” numbering of chlorinated dibenzodioxins (CDD) and dibenzofurans (CDF)

Numbers in base 16 (Hex) are used for an abbreviated designation of chlorine substitution in CDD and CDF. This “shorthand” requires two hexadecimal digits. A letter (“d” or “f”) may be used to distinguish between CDD and CDF. The digits describe the substitution patterns in positions 6,7,8,9, and 4,3,2,1, assigned values of 8,4,2, and 1, respectively. For example, 66d = 2,3,7,8-tetrachlorodibenzo-p-dioxin.     

Inclusion of 13C12-labelled mono-, di-, and tri-chlorinated dibenzo-p-dioxin and dibenzofuran standards in US EPA methods 0023A/8290

13C12-Labelled mono-, di-, and tri-chlorinated dibenzo-p-dioxin (CDD) and chlorinated dibenzofuran (CDF) standards have been tested for their applicability to standard EPA sampling and analytical Methods 0023A/8290. These methods target for analysis only the tetra- through octa-CDD/CDF homologues. Extension of the isotope dilution method to include those lower chlorinated homologues is important toward obtaining reliable species concentration data on the complete, mono- to octa-chlorinated homologue profile. These data will improve our ability to model poly-CDD/CDF concentrations through understanding mechanisms of poly-CDD/CDF formation, chlorination, and dechlorination.     

Reporting chlorinated dibenzo-p-dioxin and dibenzofuran data in scientific publications

A literature review of recent work involving the determination of chlorinated dibenzo-p-dioxins (CDD) and dibenzofurans (CDF) in fish and incinerator samples has shown many irregularities and omissions in the reported data. Although some of these result from non-standardized nomenclature and reporting practices and do not affect the overall conclusions reached, in some cases omissions in reporting experimental procedures raise important concerns regarding the validity of data and make comparison of data from different investigations difficult. It is not always necessary or even desirable to report every experimental detail of work performed, however, the ultra-trace determination of CDDs and CDFs in complex environmental samples is still at a stage where omission of key experimental details can affect the interpretation of results.     

PCDDs/DFs emissions from crematories in Japan

Concentrations of PCDDs and PCDFs in emission gases from 10 crematories were measured. The relationship between PCDDs/DFs and several factors such as structure, equipment and operational state of the crematory is discussed. Furthermore, emission of PCDDs/DFs from all crematories in Japan is estimated. The following results are obtained: (1) total concentration of PCDDs/DFs was 2.2-290 ng/N m3, whose TEQ concentration was 0.0099-6.5 ng TEQ/N m3; (2) total concentration of PCDFs was higher than that of PCDDs; (3) T4CDFs was the highest in the homologue pattern and 2,3,7,8-T4CDF was the highest in the isomer pattern; (4) emission of PCDDs/DFs was the largest in the first 20 min of cremation; (5) concentration of PCDDs/DFs was related to the existence of a secondary combustion chamber and a dust collector, and the ratio of the numbers of main and secondary combustion chambers; (6) total emission of PCDDs/DFs from crematories in Japan was estimated to be 8.9 g TEQ/yr.     

Chlorination of dibenzofuran and dibenzo-p-dioxin vapor by copper (II) chloride

Dibenzofuran (DF) is formed from phenol and benzene in combustion gas exhaust streams prior to particle collection equipment. Subsequent chlorination at lower temperatures on particle surfaces is a potential source of chlorinated dibenzofuran (CDF). Gas streams containing 8% O₂ and approximately 0.1% DF vapor were passed through particle beds containing copper (II) chloride (0.5% Cu, mass) at temperatures ranging from 200 to 400 °C to investigate the potential for CDF formation during particle collection. Experiment duration was sufficient to provide an excess amount of DF (DF/Cu=3). The efficiency of DF chlorination by CuCl₂ and the distribution of CDF products were measured, with effects of temperature, gas velocity, and experiment duration assessed. Results of a more limited investigation of dibenzo-p-dioxin (DD) chlorination by CuCl₂ to form chlorinated DD (CDD) products are also presented.The efficiency of DF/DD chlorination by CuCl₂ was high, both in terms of CuCl₂ utilization and DF/DD conversion. Total yields of Cl on CDF/CDD products of up to 0.5 mole Cl per mole CuCl₂ were observed between 200 and 300 °C; this suggests that nearly 100% CuCl₂ was utilized, assuming a conversion of two moles of CuCl₂ to CuCl per mole Cl added to DD/DF. In a short duration experiment (DF/Cu=0.3), nearly 100% DF adsorption and conversion to CDF was achieved. The degree of CDF chlorination was strongly dependent on gas velocity. At high gas velocity, corresponding to a gas–particle contact time of 0.3 s, mono-CDF (MCDF) yield was largest, with yields decreasing with increasing CDF chlorination. At low gas velocity, corresponding to a gas–particle contact time of 5 s, octa-CDF yield was largest. DF/DD chlorination was strongly favored at lateral sites, with the predominant CDF/CDD isomers within each homologue group those containing Cl substituents at only the 2,3,7,8 positions. At the higher temperatures and lower gas velocities studied, however, broader isomer distributions, particularly of the less CDD/CDF products, were observed, likely due to preferential destruction of the 2,3,7,8 congeners.     

Chlorination of dibenzofuran and dibenzo-p-dioxin vapor by copper (II) chloride

Dibenzofuran (DF) is formed from phenol and benzene in combustion gas exhaust streams prior to particle collection equipment. Subsequent chlorination at lower temperatures on particle surfaces is a potential source of chlorinated dibenzofuran (CDF). Gas streams containing 8% O₂ and approximately 0.1% DF vapor were passed through particle beds containing copper (II) chloride (0.5% Cu, mass) at temperatures ranging from 200 to 400 °C to investigate the potential for CDF formation during particle collection. Experiment duration was sufficient to provide an excess amount of DF (DF/Cu=3). The efficiency of DF chlorination by CuCl₂ and the distribution of CDF products were measured, with effects of temperature, gas velocity, and experiment duration assessed. Results of a more limited investigation of dibenzo-p-dioxin (DD) chlorination by CuCl₂ to form chlorinated DD (CDD) products are also presented.

The efficiency of DF/DD chlorination by CuCl₂ was high, both in terms of CuCl₂ utilization and DF/DD conversion. Total yields of Cl on CDF/CDD products of up to 0.5 mole Cl per mole CuCl₂ were observed between 200 and 300 °C; this suggests that nearly 100% CuCl₂ was utilized, assuming a conversion of two moles of CuCl₂ to CuCl per mole Cl added to DD/DF. In a short duration experiment (DF/Cu=0.3), nearly 100% DF adsorption and conversion to CDF was achieved. The degree of CDF chlorination was strongly dependent on gas velocity. At high gas velocity, corresponding to a gas–particle contact time of 0.3 s, mono-CDF (MCDF) yield was largest, with yields decreasing with increasing CDF chlorination. At low gas velocity, corresponding to a gas–particle contact time of 5 s, octa-CDF yield was largest. DF/DD chlorination was strongly favored at lateral sites, with the predominant CDF/CDD isomers within each homologue group those containing Cl substituents at only the 2,3,7,8 positions. At the higher temperatures and lower gas velocities studied, however, broader isomer distributions, particularly of the less CDD/CDF products, were observed, likely due to preferential destruction of the 2,3,7,8 congeners.     

Spatial distribution and reduction of PCDD/PCDF Toxic Equivalents along three shallow lowland reservoirs

Reservoirs situated along a river continuum are ecosystems where rates of transfer of suspended matter and associated micropollutants are reduced due to sedimentation, accumulation, and biological and physical transformation processes. Among the micropollutants, PCDDs and PCDFs are substances that are highly toxic and carcinogenic for humans and animals. They are emitted and dispersed in the environment throughout the whole catchment area and may accumulate in aquatic and terrestrial food chains, creating a risk for human health. A wealth of data exists indicating the increase in the concentrations of pollutants along a river continuum. A comparative analysis of total, individual, and TEQ PCDD/PCDF concentrations in large lowland, shallow reservoirs located in different catchments (“I”—industrial/urban/agricultural, “U”—urban/agricultural, and “A”—agricultural/rural) showed decreases of the TEQ concentrations in bottom sediments along a gradient from the middle sections to the dam walls. Moreover, penta-, hexa-, and heptachlorinated CDD/CDF congeners were reduced from 28.8 up to 93.6 % in all three types of reservoirs. A further analysis of water samples from the inlets and outlets of the “A” reservoir confirmed this tendency.     

PCDDs/PCDFs and PCBs in water samples from the Three Gorge Reservoir

The Three Gorge Reservoir (TGR) is the largest reservoir in China and its water quality is an important health concern, we have determined the concentrations of PCDDs/PCDFs and PCBs in the water samples collected at three seasons: August 2004, January 2005 and August 2005. The results showed that the average WHO-TEQ of total dioxins-like compounds (PCDDs/PCDFs+PCBs) was 0.06558 pg l(-1), ranged from 0.0008 to 0.32439 pg l(-1), which are much lower than other reported water sources. The main dioxins (PCDDs/PCDFs) are hepta- and octa-chlorinated dibenzo-p-dioxins (CDDs) and chlorinated dibenzofurans (CDFs). Since the levels of dioxins may change after the last water-store stage, the present study provides important data to compare the water quality in the TGR in the future.     

Polychlorinated dibenzo-p-dioxins and dibenzofurans in soils and sediments from Daliao River Basin, China

Polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/F) were analyzed in surface sediments and top soils collected from 30 sites in Daliao River Basin. The concentrations of PCDD/F ranged from 0.28 to 29.01 ng TEQ kg(-1) dw (mean value, 7.45 ng TEQ kg(-1)dw) in sediments, and from 0.31 to 53.05 ng TEQ kg(-1)dw (mean value, 7.00 ng TEQ kg(-1)dw) in soils. PCDD/F pollution in sediments from the mid- and downstream sections of Hun River was found to be relatively heavy, and the levels of PCDD/F contamination in paddy soils were generally higher than those of upland soils. Using multivariate statistical analysis, the PCDD/F homologue and congener profiles of all soil and sediment samples were compared with those of suspected PCDD/F sources. The results showed that, PCDD/F contamination in most sediments of Hun River should mainly originated from the production of organochlorine chemicals, while metal smelting was the important potential source of PCDD/F in the drainage area of Taizi River. PCDD/F contamination in paddy soils should be simultaneously attributed to the polluted water irrigation and the organochlorine pesticide application.     

Comparison of instrumental methods for chlorinated dibenzo-p-dioxin (CDD) determination - interim results of a round-robin study involving GC-MS, MS-MS, and high resolution MS

A study was designed to determine the feasibility of using GC-MS-MS techniques for the determination of chlorinated dibenzo-p-dioxins (CDD) and dibenzofurans (CDF) in difficult environmental samples with reduced cleanup. Three fish and three sediment extracts were provided to six different laboratories with GC-MS-MS capability for analysis. In addition, extracts were analysed by GC-low reduction MS (LRMS) and GC-high resolution MS (HRMS). At the time of this report, all participating GC-MS-MS laboratories had not completed their analysis of the supplied samples. All reporting laboratories found the analysis of these very complex samples difficult without extensive cleanup. GC-HRMS determination of some samples was possible with reduced cleanup compared to GC-LRMS.     

Variables affecting emissions of PCDD/Fs from uncontrolled combustion of household waste in barrels

The uncontrolled burning of household waste in barrels has recently been implicated as a major source of airborne emissions of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs). A detailed, systematic study to understand the variables affecting emissions of PCDD/Fs from burn barrels was performed. The waste composition, fullness of the barrel, and the combustion conditions within the barrel all contribute significantly to determining the emissions of PCDD/Fs from burn barrels. The study found no statistically significant effect on emissions from the Cl content of waste except at high levels, which are not representative of typical household waste. At these elevated Cl concentrations, the impact of Cl on PCDD/F emissions was found to be independent of the form of the Cl (inorganic or organic). For typical burn conditions, most of the PCDD/F emissions appear to be associated with the later stages of the burn when the waste is smoldering. Polychlorinated biphenyls (PCBs) were also measured for a subset of the tests. For the nominal waste composition, the average emissions were 76.8 ng toxic equivalency units (TEQ)WHO98/kg of waste combusted, which suggests that uncontrolled burning of household waste could be a major source of airborne PCDD/Fs in the United States.     

Ambient air monitoring of PCDD/Fs and co-PCBs in Gyeonggi-do, Korea

We started the monitoring for PCDD/Fs in ambient air and soil in August 2001, and co-PCBs in January 2002. Decreasing of PCDD/Fs and co-PCBs levels in ambient air were observed. The higher PCDD/Fs levels were found in winter and lower in autumn. We found that the industrial incinerators influenced the PCDD/Fs levels in ambient air. In the 2,3,7,8-substituted PCDD/Fs concentration profiles, the three major congeners occupied 67% of the total mass. In case of co-PCBs, PCB#118, #105 and #77 were observed as the main congeners. Five cluster groups discriminated by ratio of four components, O(8)CDD, 1,2,3,4,6,7,8-H(7)CDD, 1,2,3,4,6,7,8-H(7)CDF and O(8)CDF, were obtained from HCA (hierarchical cluster analysis).     

Total TEQ emissions (PCDD/F and PCB) from industrial sources

Flue gas samples from eight different sources (industrial plants and crematories) have been analyzed for PCDD/Fs and PCBs and total Toxicity EQuivalents (TEQ) values have been calculated using the latest WHO toxicity equivalent factors from 1998. A contribution of PCBs to the Total TEQ up to 16% was found, within the 12 WHO-PCBs PCB-126 contributes mostly to the TEQ. Thermodynamic stability of PCBs was calculated semiempirically using the MOPAC program package and differences in the heat of formation (HoF) were compared to the distribution of PCBs in real samples. Partial correspondence between fact and theory could be found.     

A status report on the U.S. national dioxin study

In 1983, the US Environmental Protection Agency (EPA) embarked on an extensive investigation of the presence and extent of contamination of the national environment by CDDs/CDFs. This status report is a prelude to a final report to be delivered to the US Congress in December, 1985.     

Formation and removal of PCDD/Fs in a municipal waste incinerator during different operating periods

The PCDD/F concentrations and removal efficiencies achieved with air pollution control devices (APCDs) during different operating periods (start-up, normal operation, and shut-down) at an existing municipal waste incinerator (MWI) in Taiwan are evaluated via stack sampling and analysis. The MWI investigated is equipped with electrostatic precipitators (EP), wet scrubbers (WS), and selective catalytic reduction system (SCR) as APCDs. The sampling results indicate that the PCDD/F concentrations at the EP inlet during start-up period were 15 times higher than that measured during normal operation period. The PCDD/F concentration observed at shut-down period was close to that measured at normal operation period. The CO concentration was between 400 and 1000 ppm during start-up period, which was about 50 times higher compared with the normal operation. Hence, combustion condition significantly affected the PCDD/F formation concentration during the waste incineration process. In addition, the distributions of the PCDD/F congeners were similar at different operating periods. During the normal operation and shut-down periods, the EP decreases the PCDD/F concentration (based on TEQ) by 18.4-48.6%, while the removal efficiency of PCDD/Fs achieved with SCR system reaches 99.3-99.6%. Nevertheless, the PCDD/F removal efficiency achieved with SCR was only 42% during the 19-h start-up period due to the low SCR operating temperature (195 degrees C).     

Effects of injected activated carbon and solidification treatment on the leachability of polychlorinated dibenzo-p-dioxins and dibenzofurans from air pollution control residues of municipal waste incineration

To assess the effectiveness of the injected activated carbon, cement, and sulfur-containing chelating agent in controlling polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) release from the surface of air pollution control (APC) residues, this study examined the leachability of PCDD/Fs from APC residues generated by municipal solid waste incinerators. Results showed that PCDD/Fs were stably retained in the APC residues when the samples were leached with acetic acid solution. Highly chlorinated PCDD/F homologues (i.e., hepta- and octa-CDDs and CDFs) were relatively easy to leach. The leaching percentages of PCDD/Fs from raw APC residue samples containing activated carbon were smaller than those from samples without activated carbon, especially when n-hexane was used as the leachant. These results indicate that the flue gas injected activated carbon not only controls PCDD/F emissions, but also suppresses the leachability of PCDD/Fs from the APC residues. Solidification/stabilization (S/S) processes with 30wt% cement and 5wt% sulfur-containing agent can additionally decrease the leachability of PCDD/Fs with humic acid. Using n-hexane as the leachant, S/S processes increased the leachability of PCDD/Fs. Various low chlorinated PCDD/F congeners were moreover leached out of the APC residue samples, markedly increasing the leachate toxicity. The enhancement of leachability and toxicity owing to S/S processes may negatively impact the environment when APC residues are exposed to nonpolar organic solvents.