硝酸根紫外光降解对硝基苯甲酸的研究

以硝酸铝做光氧化剂,研究了紫外光照射下,NO-3对PNB(对硝基苯甲酸)的光降解作用.探索了NO-3投加量、模拟废水初始浓度和pH值、光照时间、溶解氧浓度对处理效果的影响.结果表明,NO-3对PNB具有良好的光氧化作用,在最佳处理条件下,NO-3光降解PNB 4 h后降解率达90.8%.廉价硝酸盐对于有机物能起到显著光...     

腐殖酸和铁对阿特拉津光降解影响的研究

为考察除草剂在水体中的自净性能,对模拟太阳光(λ> 290 nm)下腐殖酸和铁元素对阿特拉津的光化学降解进行了研究。结果表明,单独辐照阿特拉津几乎不降解。在分别加入3、5和10 mg/L的腐殖酸时,阿特拉津的降解率分别为34.36 %、40.74%和15.66 %;在Fe(Ⅲ)投加量从0.01 mmol/L增加到0.2 mmol/L时,阿特拉津的降解率从24.36 %增加到34.97 %。而在当腐殖酸与铁共存时,阿特拉津降解率则进一步提高。紫外可见光谱和荧光光谱均表明,腐殖酸-铁络合物的形成及其光化学作用,促进了阿特拉津的降解。     

Solar photodegradation of dichloroacetic acid and 2,4-dichlorophenol using an enhanced photo-Fenton process

The photo-Fenton process using potassium ferrioxalate as a mediator was investigated for the photodegradation of dichloracetic acid (DCA) and 2,4-dichlorophenol (DCP) in aqueous medium using solar light as source of irradiation. The influence of the solution depth, the light intensity and the effect of stirring the solution during irradiation process were evaluated using DCA as a model compound. A negligible influence of stirring the solution was observed when the concentration of ferrioxalate (FeOx) was 0.8 mM and solution depth was 4.5 or 14 cm. The optimum FeOx concentration determined for solution depths between 4.5 and 14 cm was 0.8 mM considering total organic carbon (TOC) removal during DCA irradiation. The high efficiency of the photo-Fenton process was demonstrated on summer days, when only 10 min of exposition (around noon) were sufficient to completely destroy the organic carbon of a 1.0 mM DCA solution in the presence of 0.8 mM FeOx and 6.0 mM H2O2 using a solution depth of 4.5 cm. It was observed that the photodegradation efficiency increases linearly with the solar light intensity up to values around 15 Wm(-2) but this linear relationship does not hold above this value showing a square root dependence. The photodegradation of a solution of DCP/FeOx showed a lower TOC removal rate than that observed for DCA/FeOx, achieving approximately 90% after 35 min irradiation under 19 W m(-2), while under this light intensity, the same TOC removal of DCA/FeOx was achieved in only 10 min irradiation.     

酸性红R在UV-蒙脱土KSF-H_2O_2体系中光降解行为研究

以紫外杀菌灯(波长为254nm)为光源,研究了酸性红R在由蒙脱土KSF和H2O2组成的类Fenton体系中的光降解行为,研究了反应体系pH、H2O2浓度对偶氮染料酸性红R光催化降解的影响,分析了酸性红R的光降解动力学规律。结果表明:对于100mg/L的酸性红R,在pH为3.0、66mg/L的H2O2和质量浓度为1g/L的蒙脱土条件下,在UV/类Fenton体系可以获得较高的反应速率,经50min的光照,酸性红R的光降解率为87.2%;而在类Fenton体系中的光降解率只有56%左右,可见UV对类Fenton体系有明显的协同作用;酸性红R的光降解动力学规律符合Langmuir-Hinshelwood方程,反应速率常数为1.82mg/(L·min)。     

Study on the co-effect of maifanite-based photocatalyst and humic acid in the photodegradation of organic pollutant

Environmental Science and Pollution Research - In this study, the co-effect of clay mineral-based photocatalyst and humic acid on the photodegradation of dye was revealed for the first time. The...     

Hydrogen peroxide-assisted UV photodegradation of Lindane

Aqueous solutions of gamma-hexachlorocyclohexane (Lindane) were photolyzed (lambda=254 nm) under a variety of solution conditions. The initial concentrations of hydrogen peroxide (H(2)O(2)) and Lindane varied from 0 to 20 mM and 0.21 to 0.22 microM, respectively, the pH ranged from 3 to 11, and several concentration ratios of Suwannee River humic acid and fulvic acid were dissolved in the irradiated solutions. Lindane rapidly reacted, and the maximum reaction rate constant (9.7 x 10(-3) s(-1)) was observed at pH 7 and initial [H(2)O(2)]=1 mM. Thus, 90% of the Lindane is destroyed in approximately 4 min under these conditions. In addition, within 15 min, all chlorine atoms were converted to chloride ion, indicating that chlorinated organic by-products do not accumulate. The reactor was characterized by measuring the photon flux (7.04 x 10(-6) E s(-1)) and the cumulative production of *OH during irradiation. The cumulative *OH production during irradiation was fastest at an initial [H(2)O(2)]=5 mM (k=0.77 micro M s(-1)).     

2,4-Dichlorophenoxyacetic acid (2,4-D) photodegradation on WO3-TiO2-SBA-15 nanostructured composite

Environmental Science and Pollution Research - A current environmental problem is the uncontrolled use of various pesticides that are harmful to the environment and public health. The herbicide...     

Kinetics of photodegradation and ozonation of pentachlorophenol

The oxidation of 2,3,4,5,6-pentachlorophenol (PCP) has been carried out by a photodecomposition process using a polychromatic UV irradiation, and by an ozonation process. In the photodegradation process, the pH accelerated the decomposition rate and the approximate first-order rate constants were evaluated, with values between 0.16+/-0.005 min(-1) at pH=3 and 0.26+/-0.007 min(-1) at pH=9. A more rigorous kinetic study led to the determination of the quantum yields of the reaction, with values of 200+/-7x10(-3) mol/Eins for pH=3 and 22+/-1.1x10(-3) mol/Eins for pH=9. In the ozonation process, the rate constants for the reaction between ozone and PCP were determined by means of a competition kinetics, with values in the range from 0.67x10(5) to 314x10(5) l/mols. The specific rate constants for the un-dissociated and dissociated forms of PCP were also calculated. Finally, in both processes, the intermediate reaction products were identified, the most important being tetrachlorocatechol, tetrachlorohydroquinone and tetra-p-chlorobenzoquinone. Free chloride ion released, which was favored at high pHs, was also followed in both processes.     

Ferrioxalate-mediated photodegradation and mineralization of 4-Chlorophenol

INTENTION, GOAL, SCOPE, BACKGROUND: Advanced oxidation processes are powerful methods which are capable of transforming refractory, nonbiodegradable and/or toxic organic compounds into harmless end products such as carbon dioxide and water. However, one commen problem of all advanced oxidation processes is the high demand of electrical energy for ultraviolet lamps, which causes high operational costs. Minimization of the required irradiation time, and therefore the energy consumption, by optimization of other reaction conditions such as catalyst-oxidant type and concentration, pH, temperature, pollutant/oxidant ratio etc., therefore continues to gain importance. OBJECTIVE: The main objective of this study was the minimization of the required irradiation time through optimization of the use of a newly patented catalyst, ferrioxalate, and also to compare the performance of this catalyst with the performance of other AOPs. METHODS: Oxidation of 4-chlorophenol by photo-Fenton process using potassium ferrioxalate as a mediator was studied in a lab scale photoreactor. The influence of parameters such as hydrogen peroxide and ferrioxalate concentrations, initial pH, power-output, oxalate/iron ratio and different iron sources was evaluated. An upflow photoreactor equipped with a 1000 Watt high-pressure mercury vapour lamp and operating in a recirculation mode was used during photodegradation experiments. The extent of the reduction of 4-chlorophenol, Total Organic Carbon and Chemical Oxygen Demand was used to evaluate the photodegradation reaction. RESULTS AND DISCUSSION: The optimum pH range observed was found to be 2.7-3. The efficiency of 4-chlorophenol oxidation increased with increasing concentrations of hydrogen peroxide and ferrioxalate, reaching a plateau after the addition of 10 and 0.072 mM of those reagents, respectively. Using an Oxalate/iron ratio of 12 was 18% less efficient than using a ratio of 3:1. The efficiency increased with increasing radiation power. However, this increase was not linear. The UV/ferrioxalate/H2O2 process, by which complete mineralization of 100 mg l(-1) 4-chlorophenol was achieved in 20 min of total reaction time, was the most efficient process among the alternatives applied. CONCLUSIONS: The use of ferrioxalate as the catalyst was found to be more efficient than the use of Fe(II) and Fe(III) iron species. It was possible to completely mineralize 4-chlorophenol. RECOMMENDATION AND OUTLOOK: The results of this study demonstrate that the ferrioxalate-mediated degradation of 4-chlorophenol requires less irradiation times than other advanced oxidation processes. There are mainly 19 phenol isomers and other toxic and nonbiodegradable organic compounds. We recommend that similar studies should be performed on many such compounds in order to attain a clear understanding of the performance of this catalyst. Because of its light sensitivity, this catalyst should be used immediately after its preparation. The use of low pressure mercury vapour lamps in this process should also be considered, since low power outputs may be enough for the process.     

Environmental chemicals and biomembranes 1. Nitrilotriacetic acid

Nitrilotriacetic acid (NTA) is readily taken up by yeast cells through simple diffusion and is metabolized. Concentrations of NTA in the millimolar range do not interfere with various membrane functions of yeast and bacteria.     

Sunlight photodegradation of 2,4,5-trichlorophenoxy-acetic acid and 2,4,5,trichlorophenol on TiO2. Identification of intermediates and degradation pathway

The photocatalytic degradation of 2,4,5-trichlorophenoxyacetic acid and 2,4,5-trichlorophenol has been investigated in oxygenated aqueous suspensions of TiO₂. Complete mineralization to CO₂ and HC1 occurs with half-lives of 30–90 minutes. The effect of loading and thermal pre-treatment of the semi-conductor catalyst, as well as the influence of added chloride ions have been examined. In the degradation of the 2,4,5-trichlorophenoxyacetic acid, several intermediates were detected by gas-chromatographic/mass-spectrometric techniques. A scheme for the photodegradation is formulated.     

Ferric citrate-induced photodegradation of dyes in aqueous solutions

The photooxidation of dye solutions containing Fe(III)-citrate complexes was studied. The photodegradation under near-UV light of the five dyes, C. I. reactive red 2, C. I. reactive blue 4, C. I. reactive black 8, C. I. basic red 13 and C. I. basic yellow 2, in aqueous solutions at pH2.0 containing Fe(III)-citrate complexes was found to follow pseudo-first order kinetics. The photodegradation rates of the dye, C. I. reactive red 2, decreased with increasing the initial dye concentration in range of 20 – 60 mg/L . A comparatively higher photodegradation efficiency of the dye was gained under the condition of pH2.0 and the Fe(III) to citrate ratio 1:2.     

Effects of fulvic acid concentration and origin on photodegradation of polycyclic aromatic hydrocarbons in aqueous solution: Importance of active oxygen

With an Xe arc lamp house as simulated sunlight, the influences of fulvic acid (FA) concentration and origins on photodegradation of acenaphthene, fluorine, phenanthrene, fluoranthene and pyrene in aqueous solution have been studied. Similar effects of FAs, collected from five places around China, on polycyclic aromatic hydrocarbon (PAH) photodegradation have been observed. Active oxygen was of significance in PAH photodegradation with the presence of FAs. For systems with 1.25 mg L⁻¹ FAs, the contributions of OH to PAH photodegradation rates were from 33% to 69%. FAs had two opposite effects, i.e., stimulating the generation of active oxygen and advancing PAH photodegradation; competing with PAHs for energy and photons and restraining PAH photodegradation. Generally, photodegradation rates of the 5 PAHs decreased with the increase of FAs concentration; except fluoranthene and pyrene were advanced in solutions with low FA concentration. The influences of FA concentration on PAH photodegradation were more significant than FA origin.     

Modeling of gas-phase photodegradation of chloroform and carbon tetrachloride

The relationship between the irradiance in a photoreactor and the rate of photodegradation of organics is essential in the scaling-up of photoreactors to treat large volumes of air contaminated with organic pollutants. In this study, the analysis is adopted to compare results obtained from two different photoreactors. Initially, the applicability of two light models in calculating the irradiance in two photoreactors was evaluated. Thereafter, kinetic models of ultraviolet (UV) photooxidation of chloroform (CHCl3) and carbon tetrachloride (CCl4) from the archived literature were tested using experimental data under various operating conditions and different irradiances. Sensitivity analyses were conducted using different values of model parameters to determine the significance of each parameter on the photodegradation of the two chlorinated organics. For compounds that undergo photolysis as a primary mode of degradation, the rate of photodegradation at low initial concentrations can be predicted easily by the following equation: d[C]/dt = -2.303Iave, lambdaepsilonlambdaphilambda[C]. Although the photodegradation of chlorinated organic compounds in dry and humid air can be predicted well, it is difficult to predict the Cl* sensitized oxidation occurring at high initial concentrations. A good agreement between the simulated and experimental data provides a sound basis for the design of large-scale reactors.     

The enhancement of photodegradation efficiency using Pt-TiO2 catalyst

The residues from the extraction of lead/zinc (Pb/Zn) ores of most Pb/Zn mines are permanently stored in tailings ponds, which require revegetation to reduce their environmental impact. This can only be done if the main constraints on plant establishment are evaluated. This can readily be done by field and greenhouse studies.

To test this, the properties of different tailings from Lechang Pb/Zn mine located at the north of Guangdong Province in southern China have been studied. Physical and chemical properties including concentrations of metals (Pb, Zn, Cd and Cu) in the tailings and soils collected from different sites have been measured. The results showed that tailings contain low nitrogen (0.016–0.075%), low-organic matter (0.58–1.78%), high salt (3.55–13.85 dS/m), and high total and diethylene–tetramine–pentaacetic acid (DTPA)-extractable metal concentrations (total: 1019–1642 μg g⁻¹ Pb, 3078–6773 μg g⁻¹ Zn, 8–23 μg g⁻¹ Cd, and 85–192 μg g⁻¹ Cu; DTPA-extractable: 59–178 μg g⁻¹ Pb, 21–200 μg g⁻¹ Zn, 0.30–1.5 μg g⁻¹ Cd, and 4.3–12 μg g⁻¹ Cu). Aqueous extracts of tailings/soils (10%, 20% and 30%, w/v) from different sites were prepared for testing their effects on seed germination and root elongation of a vegetable crop Brassica chinensis and a grass species Cynodon dactylon. It was found that root elongation provided a better evaluation of toxicity than seed germination. The ranking of toxicity using root elongation was: high-sulfur tailings>tailingdam>sparsely vegetated tailings>densely vegetated tailings>mountain soil for both plants. This order was consistent with DTPA-extractable Pb contents in the tailings and soils. B. chinensis seedlings were then grown in the mixtures of different proportions of tailings and farm soil for 4 weeks, and the results (dry weights of seedlings) were in line with the root elongation test. All these demonstrated that heavy metal toxicity, especially available Pb, low content of nutrient, and poor physical structure were major constraints on plant establishment and colonization on the Pb/Zn mine tailings.     

Dye-sensitized photodegradation of the fungicide carbendazim and related benzimidazoles

The present work studies the visible-light-promoted photodegradation of the colorless fungicide carbendazim (methyl 2-benzimidazolecarbamate) and several 2-substituted benzimidazoles (SBZ's), in water or water-methanol solution, in the presence of air and, as a photosensitizer, the synthetic xanthene dye Rose Bengal (RB) or the natural pigment riboflavin (Rf). The results indicate that the degradation of each particular SBZ depends on its chemical structure and on the sensitizer employed. In the presence of RB, the degradation always operates via a singlet molecular oxygen (O(2)((1)Delta(g)))-mediated mechanism, through a highly efficient process, as deduced from the comparison of the rate constants for physical and chemical quenching of O(2)((1)Delta(g)). In the presence of Rf, the visible-light irradiation of any of the studied SBZ's produces a series of competitive processes that depend on the relative concentrations of Rf and SBZ. These processes include the quenching of excited singlet and triplet Rf states by the SBZ and the generation of both O(2)((1)Delta(g)) and superoxide radical anion (O(2)(-)), the latter generated by electron transfer from excited Rf species to the dissolved oxygen. The overall result is the photodegradation of the SBZ and the photoprotection of the sensitizer.     

Effect of photosensitizer diethylamine on the photodegradation of polychlorinated biphenyls

The objective of this study was to investigate the effect of diethylamine and xenon simulated sunlight on the photodegradation of two forms of PCBs including PCBs in transformer oil and PCB congener 138. The result of GC chromatograms illustrated the shifting pattern of higher chlorinated biphenyls in transformer oil degraded to lower chlorinated biphenyls with the extension of exposure time. The effect of diethylamine and xenon simulated sunlight was significant on the photodegradation of both PCBs in transformer oil and congener 138. The initial degradation rates of congener 138 (1.14 x 10(-9) to 4.47 x 10(-9) mol l(-1) h(-1)) were in direct proportion to the initial concentrations of congener 138 which confirmed the pseudo-first-order reaction of PCB photodegradation. The apparent quantum yields (phi) of congener 138 using diethylamine in xenon photoreactor were ranged between 2.08 x 10(-2) and 9.8 x 10(-4). PCB congeners 123, 97, 70, 67, 33, 29, 17, 12, and 9 were detected as the descendants of the photodegradation of congener 138 through dechlorination. The major pathway of congener 138 photodegradation in this study was via para-dechlorination.     

Effect of fatty acids and oils on photodegradation of azadirachtin-A

Azadirachtin-A on exposure to UV-light (254 nm) as a thin film on glass surface gave a isomerised (Z)-2-methylbut-2-enoate product. Half-life of azadirachtin-A as thin film under UV light was found to be 48 min. Azadirachtin-A was irradiated along with saturated and unsaturated fatty acids, and fatty oils under ultra-violet light as thin film. Saturated fatty acid increased the rate of photodegradation of azadirachtin-A, whereas unsaturated fatty acids such as oleic, linoleic and elaidic acid reduced the rate of degradation. Castor, linseed and olive oil accelerated the rate of degradation, whereas neem oil showed no or little change in the rate of degradation of azadirachtin-A. None of these fatty acids and fatty oils were effective in controlling the rate of degradation of azadirachtin-A under UV-light as thin film.