H_2O_2强化水力空化降解罗丹明B废水

通过投加H2O2来强化水力空化技术降解罗丹明B废水(后称"Rh B"),考察了入口压力、p H、H2O2投加量和Rh B起始浓度等因素对Rh B降解效果的影响。结果表明,Rh B的降解规律符合拟一级降解动力学;随着入口压力的增加Rh B降解率增加;酸性条件能有效提高Rh B降解率,p H=3.0时Rh B达到最大降解率95.12%;H2O2能有效强化水力空化对Rh B的降解能力,但当H2O2浓度增至10 mg/L后,Rh B的降解率则不再增加;Rh B降解率与其起始浓度成反比;最后探究了Rh B的降解机理。     

Fe(Ⅲ)-富马酸盐体系光降解黄连素

紫外光(UV)照射下,利用Fe(Ⅲ)-富马酸盐体系对黄连素(berberine)的降解反应进行研究。探讨Fe(Ⅲ)、富马酸盐(fumarate)和黄连素的初始浓度及溶液pH值对黄连素降解率的影响,并对黄连素的降解过程进行了动力学分析和机理分析。结果表明,在紫外光照射下,Fe(Ⅲ)-富马酸盐体系对黄连素有较好的降解效果。当Fe(Ⅲ)和富马酸钠初始浓度分别为25μmol/L和250μmol/L,溶液pH值为3.0时,紫外光照75 min后黄连素降解率接近91%。在pH 2.0~6.0范围内,pH值越大黄连素的降解率越低;Fe(Ⅲ)和富马酸盐初始浓度的增大能促进黄连素的降解;而随着黄连素初始浓度的增大,其降解率逐渐降低。动力学分析表明,黄连素光降解过程符合一级动力学。利用异丙醇和硫脲猝灭法证明Fe(Ⅲ)-富马酸盐体系在光反应过程中产生了羟基自由基和超氧负离子自由基。通过紫外光谱、红外光谱、TOC检测和GC-MS分析表明,在紫外光照射下黄连素在Fe(Ⅲ)-富马酸盐体系中结构被破坏,降解为小分子物质。     

高铁酸钾降解苯胺废水的机制研究

研究了高铁酸钾投加量、初始pH及苯胺初始浓度对苯胺降解效果的影响.结果表明.苯胺废水的COD去除事随高铁酸钾投加量和苯胺初始浓度的增大而升高,而初始pH对COD去除率影响不明显.对高铁酸钾降解苯胺废水后的产物进行了气相色谱/质谱(GCIMS)分析.在此基础上详细探讨了高铁酸钾降解苯胺的机制.     

光电芬顿矿化草甘膦有机废水

以有机磷农药-草甘膦为目标污染物,利用光电芬顿方法对其进行降解研究。研究汇总考察了电流强度、初始p H、Fe2+浓度、草甘膦初始浓度、光种类及通入背景气体种类对草甘膦降解效果的影响。实验结果表明:电流强度越大,草甘膦初始浓度越低,草甘膦降解效果越好;草甘膦在p H=2.0~3.0的酸性体系中降解效果最好;Fe2+浓度升高,草甘膦降解效果增强。在电流为0.36 A、初始p H=3.0、Fe2+浓度为1.0 mmol·L~(-1)、通入100 m L·min-1O2条件下,以365 nm紫外光照射的光电芬顿反应降解初始浓度为84.5 mg·L~(-1)的草甘膦溶液,处理360 min后溶液矿化率可达64.5%。     

臭氧-BAF组合工艺处理电镀RO浓水

电镀废水反渗透(RO)浓水具有盐度高、难降解有机物浓度高、含重金属等特点,是电镀废水处理工艺提标改造的难点。采用臭氧-曝气生物滤池(BAF)组合工艺,对电镀废水反渗透(RO)浓水中有机物进行处理,使出水COD浓度达到《电镀污染物排放标准》中标准。考察了废水初始p H、臭氧浓度和反应时间等因素对臭氧氧化效果的影响,以及水力停留时间(HRT)和气水比对BAF单元COD去除效果的影响。经优化后的系统运行工况为:臭氧氧化单元中废水初始p H值为10.0,臭氧浓度为31.96 mg·L~(-1),反应时间为40 min;BAF的HRT为3 h,气水比为5∶1。在最佳工况下,当进水COD为180~240 mg·L~(-1)时,经组合工艺处理后COD去除率达78.6%,平均出水COD浓度为47 mg·L~(-1),达到了标准的要求。     

超声波降解水溶液中对二氯苯

采用超声波降解含对二氯苯(p-DCB)的溶液,研究了p-DCB降解的动力学和影响因素.结果表明:(1)超声波降解水溶液中的p-DCB,随着p-DCB初始浓度的增加降解率减小;p-DCB的超声波降解反应符合表观一级动力学规律.(2)增大超声波频率和功率以及双频率联合使用可以增大p-DCB的降解率和一级反应速率常数.(3)弱酸性或中性环境更有利于p-DCB的降解进行.(4)反应时的搅拌和自由基清除剂的投加都降低了p-DCB的降解率,这是因为超声波降解时空化气泡内的热裂解和自由基作用的削弱.(5)在单一体系中,p-DCB比对氯苯胺(p-ClA)更易降解.在混合体系中,p-ClA的加入没有显著降低p-DCB的去除效果,因为亲水的p-ClA不易挥发,难以进入空化气泡竞争能量和自由基,其存在对空化气泡内混合气体的比热容比影响较小;而p-DCB的存在却明显降低了p-ClA的降解效果,因为疏水的p-DCB易挥发进入空化气泡竞争能量和自由基,并降低混合气体的比热容比.     

涡流空化/Fenton协同降解溶液中活性艳红K-2BP

采用涡流空化(SC)/Fenton协同降解溶液中活性艳红K-2BP,探讨了H2O2、Fe2+、pH、涡流压力以及活性艳红K-2BP初始浓度对SC/Fenton降解效果的影响。结果表明,H2O2和Fe2+的浓度过高或过低都会降低活性艳红K-2BP的降解率,低pH环境有助于活性艳红K-2BP的降解,活性艳红K-2BP的降解率随涡流压力的增大而升高,随其初始浓度的增加而降低。当活性艳红K-2BP初始质量浓度为10mg/L,H2O2质量浓度为165mg/L,Fe2+摩尔浓度为1.5×10-4mol/L,pH为4.0,涡流压力为0.8MPa时,活性艳红K-2BP降解率可达91.81%。     

电化学氧化法处理含盐苯醌模拟废水

利用钛基二氧化铅电极(Ti/PbO_2)作为电催化活性阳极,通过电化学氧化技术对苯醌进行降解矿化,考察常见共存无机盐对苯醌废水降解效率的影响。结果表明,NaCl存在下苯醌废水溶液的COD去除率相比硝酸盐提高了62%,相比硫酸盐提高了45%,NaCl能够显著增强电氧化去除苯醌的电流效率。苯醌的降解对氯离子非常敏感,存在少量的氯离子即可以引起氧化效率明显增加。氯离子浓度越高,苯醌模拟废水的COD去除率越高;但当氯离子浓度高于0.3mol·L~(-1)时,COD去除率反而有所下降。pH为8的弱碱性环境更有利于含氯离子苯醌废水的电氧化降解反应。提高电流密度可增大COD去除率;但升高温度会降低COD去除率。在pH为8、NaCl浓度为0.3 mol·L~(-1)、电流密度为10mA·cm~(-2)、温度为20℃的条件下,初始浓度为100 mg·L~(-1)的苯醌经3 h电化学氧化降解后COD去除率可达80.9%。通过高效液相色谱对电氧化降解苯醌的中间产物进行分析,发现氯离子存在下苯醌的降解速度显著提高,中间产物顺丁烯二酸的生成速度更快,这说明由氯离子生成的强氧化剂对苯醌具有极强的开环能力。     

3种不同工艺中莠灭净的去除特性及自由基鉴定

以三嗪类除草剂莠灭净(AMT)为目标污染物,对比研究了紫外(UV)、紫外激活过硫酸盐(UV/PS)与紫外激活过一氧硫酸氢盐(UV/PMS)3种不同工艺对AMT的去除效果以及反应动力学模型。考察了底物初始浓度、氧化剂浓度、溶液初始pH和水中腐殖酸浓度对AMT降解的影响,并对反应中生成的主要自由基进行鉴定。结果表明,3种系统下AMT降解均符合拟一级反应动力学模型(R~2≥0.93)。AMT在3种不同系统下降解效率基本遵循UV/PSUV/PMSUV规律。随着底物初始浓度的增加,AMT降解率减小,拟一级速率常数kobs减小;增加氧化剂的投加量可以促进AMT降解;溶液pH的改变对UV系统下AMT的降解影响较小,而在UV/PS系统下,随着pH的增大降解率逐渐减小,在UV/PMS系统中降解率则呈现先减小后增大的趋势;投加腐殖酸会抑制AMT的降解;pH为7时,UV/PS和UV/PMS系统中反应生成的自由基主要是·SO_4~-。     

臭氧氧化降解烷基多苷的试验研究

分析了碱性介质臭氧降解烷基多苷(APG)的机制,进行了臭氧氧化降解APG的试验研究。结果表明,臭氧对APG有较强的氧化能力;有机质初始浓度高有利于其氧化降解;初始阶段降解速率较快,当COD降解率达80%时,再增加臭氧的通入量,降解变慢;臭氧氧化处理APG过程中泡沫的产生、存在的时间及消除与APG的浓度、氧化降解程度密切相关。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.