Utilisation of environmentally friendly okara-based biosorbent for cadmium(II) removal

Environmental Science and Pollution Research - Heavy metals released by various industries are among the major pollutants found in water resources. In this research, biosorption technique was...     

Enhanced removal of lead(II) and cadmium(II) from water in alum coagulation by ferrate(VI) pretreatment.

A laboratory study demonstrated that ferrate pretreatment significantly enhanced lead and cadmium removal in alum coagulation, under the conditions of natural surface water. The enhancement of lead removal was approximately 21 to 37% by ferrate pretreatment at a dosage of 1 to 5 mg/L. The enhanced removal of cadmium by ferrate pretreatment at a dosage of 1 to 5 mg/L exceeded the removal by alum coagulation alone 2-to 12-fold. Cadmium is much more difficult to remove than lead in alum coagulation. The performance of ferrate in enhancing the removal of lead and cadmium in alum coagulation was better than that of ferric chloride. The removal of lead and cadmium was highly pH-dependent, following the general trend of higher pH being related to higher removal. Satisfactory removal of cadmium could be expected by ferrate pretreatment combined with adjusting the pH of the water.     

Removal of Pb(II) ions from aqueous solution and industrial effluent using natural biosorbents

Purpose

The purpose of the research is to investigate the applicability of the low-cost natural biosorbents for the removal of Pb(II) ions from aqueous solution and effluent from battery industry.

Methods

Six different biosorbents namely rice straw, rice bran, rice husk, coconut shell, neem leaves, and hyacinth roots have been used for the removal of Pb(II) ions from aqueous solution in batch process. All the biosorbents were collected from local area near Kolkata, West Bengal, India. The removal efficiency was determined in batch experiments for each biosorbent.

Results

The biosorbents were characterized by SEM, FTIR, surface area, and point of zero charge. The sorption kinetic data was best described by pseudo-second-order model for all the biosorbents except rice husk which followed intraparticle diffusion model. Pb(II) ions adsorption process for rice straw, rice bran, and hyacinth roots were governed predominately by film diffusion, but in the case of rice husk, it was intraparticle diffusion. Film diffusion and intraparticle diffusion were equally responsible for the biosorption process onto coconut shell and neem leaves. The values of mass transfer coefficient indicated that the velocity of the adsorbate transport from the bulk to the solid phase was quite fast for all cases. Maximum monolayer sorption capacities onto the six natural sorbents studied were estimated from the Langmuir sorption model and compared with other natural sorbents used by other researchers. The Elovich model, the calculated values of effective diffusivity, and the sorption energy calculated by using the Dubinin?CRadushkevich isotherm were indicated that the sorption process was chemical in nature. The thermodynamic studies indicated that the adsorption processes were endothermic. FTIR studies were carried out to understand the type of functional groups responsible for Pb(II) ions binding process. Regeneration of biosorbents were carried out by desorption studies using HNO₃. Battery industry effluents were used for the application study to investigate applicability of the biosorbents.

Conclusion

The biosorbents can be utilized as low-cost sorbents for the removal of Pb(II) ions from wastewater.     

The marine macroalga Cystoseira baccata as biosorbent for cadmium(II) and lead(II) removal: kinetic and equilibrium studies

This work reports kinetic and equilibrium studies of cadmium(II) and lead(II) adsorption by the brown seaweed Cystoseira baccata. Kinetic experiments demonstrated rapid metal uptake. Kinetic data were satisfactorily described by a pseudo-second order chemical sorption process. Temperature change from 15 to 45 degrees C showed small variation on kinetic parameters. Langmuir-Freundlich equation was selected to describe the metal isotherms and the proton binding in acid-base titrations. The maximum metal uptake values were around 0.9 mmol g(-1) (101 and 186 mg g(-1) for cadmium(II) and lead(II), respectively) at pH 4.5 (raw biomass), while the number of weak acid groups were 2.2 mmol g(-1) and their proton binding constant, K(H), 10(3.67) (protonated biomass). FTIR analysis confirmed the participation of carboxyl groups in metal uptake. The metal sorption was found to increase with the solution pH reaching a plateau above pH 4. Calcium and sodium nitrate salts in solution were found to affect considerably the metal biosorption.     

Copper and cadmium removal from synthetic industrial wastewater using chitosan and nylon 6

Purpose

Chitosan with nylon 6 membranes was evaluated as adsorbents to remove copper and cadmium ions from synthetic industrial wastewater.

Methods

Chitosan and nylon 6 with glutaraldehyde blend ratio with (1:1+Glu, 1:2+Glu, and 2:1+Glu) have been prepared and these were used as membranes to remove copper and cadmium ions from synthetic industrial wastewater. Characterization of the synthesized membrane has been done with FTIR, XRD, TGA/DTA, DSC, and SEM. Chemical parameters for quantities of adsorption of heavy metal contamination have been done and the kinetics of adsorption has also been carried out.

Results

The optimal pH for the removal of Cd(II) and Cu(II) using chitosan with nylon 6. Maximum removal of the metals was observed at pH 5 for both the metals. The effect of adsorbent dose also has a pronounced effect on the percentage of removal of the metals. Maximum removal of both the metals was observed at 5 g/100 ml of the adsorbent.

Conclusion

Copper and cadmium recovery is parallel at all time. The percentage of removal of copper increased with increase in the pH from 3 to 5. In the case of cadmium containing wastewater, the maximum removal of metal occurred at pH 5. The uptake amount of Cu²⁺ ions on chitosan increased rapidly with increasing contact time from 0 to 360 min and then reaches equilibrium after 360 min; the equilibrium constant for copper and cadmium ions is more or less the same for the adsorption reaction.     

Fabrication of novel bio-adsorbent and its application for the removal of Cu(II) from aqueous solution

Environmental Science and Pollution Research - As eco-friendly adsorption material, hydroxyapatite (Ca5(PO4)3OH, HA) has been extensively applied to the removal of heavy metal ions. However,...     

Characterization and lead(II), cadmium(II), nickel(II) biosorption of dried marine brown macro algae Cystoseira barbata

Purpose

The objectives of this research are to identify the functional groups and determine corresponding pK _a values of the acidic sites on dried brown algae Cystoseira barbata using FTIR and potentiometric titrations, and to investigate the biosorption ability of biomass towards divalent nickel, cadmium, and lead ions. Adsorption was studied as a function of solution pH and contact time, and experimental data were evaluated by the Langmuir isotherm model.

Methods

CaCl₂ pretreatment was applied to the sorbent for enhancing the metal uptake capacity. The effect of solution pH on biosorption equilibrium was investigated in the pH range of 1.5?C5.0. Individual as well as competitive adsorption capacity of the sorbent were studied for metal cations and mixtures.

Results

The retention of the tested metal ions was mostly influenced from pH in the range of 1.5?C2.5, then stayed almost constant up to 5.0, while Ni(II) uptake showed the highest variation with pH. Potentiometric titrations were performed to find the number of strong and weak acidic groups and their acidity constants. The density of strong and weak acidic functional groups in the biomass were found to be 0.9 and 2.26?mmol/g, respectively. The FTIR spectra of the sorbent samples indicated various functionalities on the biomass surface including carboxyl, hydroxyl, and amino and sulphonate groups which are responsible for the binding of metal ions.

Conclusions

The capacity of the biomass for single metal ions (around 1?mmol/g) was increased to 1.3?mmol/g in competitive adsorption, Pb(II) showing the highest Langmuir intensity constant. Considering its extremely high abundance and low cost, C. barbata may be potentially important in metal ion removal from contaminated water and industrial effluents.     

循环式活性污泥工艺协同处理榨菜废水与城镇污水脱氮效果

利用CASS工艺协同处理高盐高氮榨菜有机废水和生活污水,针对协同处理碳源不足问题,提出以榨菜废水和甲醇作为碳源的两种碳源投加方案,对比分析了CASS工艺在运行周期为8 h、排水比为30%、回流比为100%、预处理后的榨菜废水掺入比为20%的条件下,分别以榨菜废水和甲醇补充碳源及不外加碳源3种情况的脱氮效果。实验结果表明,不外加碳源时,协同处理进水C/N小于3∶1,系统脱氮效果差,出水总氮不达标;以榨菜废水和甲醇为碳源提高C/N至4∶1～5∶1时,系统脱氮效果提高,出水总氮满足GB18918-2002一级B标排放标准;盐度的变化对微生物活性产生的抑制作用,当盐度升高0.1%±0.02%时,微生物系统恢复时间为10 d,而当盐度降低0.1%±0.02%时,微生物系统恢复时间为15 d。     

MnO2负载树脂的制备及对As(Ⅴ)的去除效果

制备了大孔和DH302 2种MnO2的负载树脂.并用SEM、EDS手段表征了负载树脂,实验了负载MnO2后树脂对As(Ⅴ)的去除效果.结果表明:负载树脂对As(Ⅴ)的去除效果比原树脂有很大提高;吸附As(Ⅴ)后的2种负载树脂,均能较好地解吸并可重新用于对As(Ⅴ)的吸附实验.     

Cu(II) removal from aqueous solution usingDogantepe (Amasya) zeolites

This paper investigates the effects of zeolite particle size, zeolite/ solution ratio and stirring time on the performance of zeolites from Dogantepe in removing Cu(II) from aqueous solution to establish optimum operating conditions. The results indicated that the size of the zeolite samples, the concentration of Cu(II) and the zeolite/solution ratio affected the removal efficiencies, whilst the stirring time was found to have no significant effect on the removal efficiencies. The equivalent numbers of sodium, magnesium, calcium and potassium ions passed into the Cu(II) solution were found to be 1.196, 0.208, 0.117 and 0.009 meq/l, respectively, and the passing percentages of these ions were calculated to be 11.27, 2.45, 1.57 and 0.37%, respectively. The removal mechanism of Cu(II) with zeolite samples was mainly ion exchange with a fraction of approximately 65%. The maximum exchange capacities obtained by using Dogantepe zeolites, Yavu zeolites, and synthetic resin were found to be 9.2, 7.0 and 72.7 mg/g, respectively. However, in relatively low concentrations of Cu(II), the differences in the removal efficiencies or exchange capacities obtained for above different three materials were significantly decreased.     

Biosorption of cadmium(II) and copper(II) ions from aqueous solution by core of Artocarpus odoratissimus

Purpose

This research is on the evaluation of biosorption capability of the core of Artocarpus odoratissimus (Tarap), grown in Brunei Darussalam, towards Cd(II) and Cu(II) ions present in synthetic solutions, and to characterize the surface of Tarap particles.

Methods

Thermogravimetric analysis and surface titrations were conducted to characterize the surface of dried Tarap core particles. Atomic absorption spectroscopic measurements were conducted to determine the extent of removal of Cd(II) and Cu(II) under different experimental conditions.

Results

Mass reductions associated with many exothermic reaction peaks were observed beyond 200°C up to 650°C indicating the combustion of organic matter in Tarap. Dried particles of core of Tarap bear a negative surface charge promoting strong interaction towards positively charged ions, such as Cu(II) and Cd(II). Biosorption of the two metal ions on Tarap, which is relatively high beyond pH?=?4, occurs within a short period of exposure time. The extent of biosorption is enhanced by acid treatment of the biosorbent, and further it does not significantly depend on the presence of nonreacting ions up to an ionic strength of 2.0?M.

Conclusion

Strong attraction between each metal ion and the biosorbent is attributed to the negative surface charge on the biosorbent within a broad pH range. Acid treatment of the biosorbent improves sorption characteristics, suggesting that ion exchange plays an important role in the metal ion??biosorbent interaction process.     

Evaluation of municipal sewage treatment systems for pollutant removal efficiency by measuring levels of micropollutants

In order to evaluate the municipal sewage treatment systems used at Harbin municipal sewage treatment plant for their pollutant removal efficiency, raw sewage and effluent samples at different treatment stages from the sewage treatment systems were taken, priority pollutants (PPs) were identified and quantified using gas chromatography-mass spectrometry (GC-MS) and inductively coupled plasma-atomic emission spectrograph (ICP-AES). The test results indicated that there were one hundred and fifty species of organic pollutants identified in the raw sewage sample, and only ten species of PPs in all the sewage samples. The levels of dimethyl phthalate (DMP), diethyl phthalate (DEP), dibutyl phthalate (DBP), di-n-octyl phthalate (DnOP) in the sewage samples were 0.779-0.111 microg l(-1), 1.977-0.022 microg l(-1), 6.411-2.194 microg l(-1) and 7.152-2.953microg l(-1), respectively, and most of these phthalate esters (PAEs) were removed through anaerobic/aerobic (A/O) process; The levels of alachlor, acetochlor, atrazine were 0.074-0.021 microg l(-1), 0.160-0.096 microg l(-1) and 0.238-0.184 microg l(-1), respectively, and the total removal efficiency of atrazine was poorest through the sewage treatment systems. The levels of Cu, Cr, Se, Hg, Ni and Zn were 0.0030-0.2327 mg l(-1). It is therefore concluded from these results that the sewage treatment systems were efficient in removing most of the organic and inorganic compounds in this study, and so, the discharged effluent could cause little of the secondary pollution of the aquatic environment.     

Impact of pyrolysis temperature and activation on oily sludge-derived char for Pb(II) and Cd(II) removal from aqueous solution

Environmental Science and Pollution Research - This study investigated the Pb(II) and Cd(II) sorption from aqueous solution by oily sludge-derived char (OSDC) prepared at different pyrolysis...     

Microwave-assisted synthesis of hydroxyapatite for the removal of lead(II) from aqueous solutions

Purpose

This study has the objective to evaluate the lead(II) removal capacity of hydroxyapatite powder synthesized by microwave as an alternative method to decrease production time and cost.

Methods

Hydroxyapatite (HA) was synthesized by a microwave-assisted precipitation method using calcium nitrate and ammonium hydrogen phosphate as calcium and phosphorus sources, respectively. X-ray diffraction and Fourier transform infrared results clearly revealed that the resulting powder was HA with high purity and crystallinity. The obtained powder was used for the removal of lead(II) from aqueous solutions. The effects of pH, amount of adsorbent, initial lead(II) concentration, and contact time were studied in batch experiments.

Results

In the adsorption experiments, maximum lead(II) retention was obtained at pH 6. Adsorption equilibrium was established after 40 min. It was found that the adsorption of lead(II) on HA was correlated well (R ²?=?0.958) with the Freundlich equation for the concentration range studied. Both ion exchange and adsorption process were thought to exist in the removal process.

Conclusions

This study indicates that easily and rapidly synthesized HA by microwave-assisted precipitation method could be used as an efficient adsorbent for removal of lead(II) from aqueous solutions.     

生物接触氧化—复合人工湿地组合工艺对工业园区污水的处理效果研究

根据广州从化市玮思工业园排放的综合污水的特点,设计了生物接触氧化—复合人工湿地组合工艺对其进行处理,考察了该工艺运行一年来对COD、BOD5、TP、NH4+ -N、TN的去除效果.结果表明,该组合工艺对工业园区综合污水中的COD、BOD5、TP、NH4+ -N和TN都有较好的去除效果,出水COD、BOD5、TP、NH4+ -N、TN的平均去除率分别为86.07％、74.91％、60.73％、89.62％、46.01％;该组合工艺对各污染物的去除效果明显优于单一的生物接触氧化池和单一的复合人工湿地的去除效果,生物接触氧化池对COD、BOD5和NH4+ -N的去除贡献较大,但对TP和TN的去除能力有限;采用该组合工艺处理工业园区综合污水,具有运行费用低、处理效果好、操作方便、管理简单、景观效果良好等优点.     

Primary biosorption mechanism of lead (II) and cadmium (II) cations from aqueous solution by pomelo (Citrus maxima) fruit peels

Environmental Science and Pollution Research - The present work investigates the primary adsorption mechanisms of lead (II) and cadmium (II) cations onto pomelo fruit peel (PFP) from aqueous...     

Recent advances in nanomaterial developments for efficient removal of Hg(II) from water

Environmental Science and Pollution Research - “Water” contamination by mercury Hg(II) has become the biggest concern due to its severe toxicities on public health. There are different...     

Effects of Mn(II) and Fe(II) on microbial removal of arsenic (III)

Goal, scope, and background  Arsenic contamination in groundwater creates severe health problems in the world. There are many physiochemical and biological methods available for remediation of arsenic from groundwater. Among them, microbial remediation could be taken as one of the least expensive methods, though it takes longer treatment time. The main objective of this research was to study the improvement on remediation by addition of some essential ion salts such as Mn and Fe. Materials and methods   Staphylococcus aureus, Bacillus subtilis, Klebsiella oxytoca, and Escherichia coli were taken as model microbes from Dhulikhel, 30 km east from Kathmandu, Nepal. Results and discussion  Microbes used in this study showed different abilities in their removal of As(III) with and without addition of Mn and Fe salts. The trend of remediation increased with time. S. aureus was found to be the best among the microbes used. It showed almost 100% removal after 48-h culture, both with and without Fe and Mn salts. Rate of removal of As increased with addition of Fe and Mn for all microbes. Removal efficiency was found to increase by about 32% on average after addition of salts in 24-h cultures of S. aureus.     

Regeneration of spent TiO2 nanoparticles for Pb (II), Cu (II), and Zn (II) removal

Spent sorbents in water treatment processes have potential risks to the environment if released without proper treatment. The aim of this work was to investigate the potential regeneration of commercially prepared nano-TiO₂ (anatase) for the removal of Pb (II), Cu (II), and Zn (II) by pH 2 and ethylenediaminetetraacetic acid (EDTA) solutions. The percent of metal adsorption/desorption decreased with the increasing number of regeneration cycles, and the extent of decrease varied for each metal. Competitive effects were observed for the adsorption/desorption of different metals when the nano-TiO₂ was regenerated by EDTA solutions. Nano-TiO₂ was able to treat simulated metal polluted water with greater than 94 % adsorption and greater than 92 % desorption after four cycles of regeneration using pH 2 solution. These results demonstrated that nano-TiO₂ can be regenerated and reused using pH 2 solution compared to an EDTA solution for aquatic metal removal, which makes nanosorbents promising and economically and environmentally more attractive in the application of water purification.     

矿渣制备的无机复合絮凝剂在城市污水深度除磷中的应用

以制铝矿渣及铝土矿制备的无机复合絮凝剂进行污水深度除磷研究。在模拟废水条件下,确定了自制絮凝剂除磷的最佳pH为8、最佳投加量0.08 g/L及最佳水力条件(快速搅拌30 s、转速200 r/min;慢速搅拌15 min、转速20 r/min);然后将其用于处理生活污水站二级出水,TP、TN、COD、NH3-N和浊度去除率分别为94.69%、62.78%、78.93%、47.94%和89.30%,优于《城镇污水处理厂污染物排放标准》(GB 18918-2002)一级B标准,自制絮凝剂除磷效果优于常用市售絮凝剂PAC(TP去除率91.73%);自制絮凝剂的除磷机理主要以沉淀和电性中和作用为主,以吸附架桥和网捕卷扫作用为辅。