Determination of benzene, toluene, ethylbenzene, xylenes in water at sub-ng l-1 levels by solid-phase microextraction coupled to cryo-trap gas chromatography-mass spectrometry

A trace analytical method of benzene, toluene, ethylbenzene and xylenes (BTEX) in water has been developed by using headspace solid-phase microextraction (HS-SPME) coupled to cryo-trap gas chromatography-mass spectrometry (GC-MS). The chromatographic peak shape for BTEX was improved by using cryo-trap equipment. The HS-SPME experimental procedures to extract BTEX from water were optimized with a 75 microm carboxen/polydimethylsiloxane (CAR/PDMS)-coated fiber at a sodium chloride concentration of 267 g l(-1), extraction for 15 min at 25 degrees C and desorption at 290 degrees C for 2 min. Good linearity was verified in a range of 0.0001-50 microg l(-1) for each analyte (r(2)=0.996-0.999). The limits of detection (LODs) of BTEX in water reached at sub-ng l(-1) levels. LODs of benzene, toluene, ethylbenzene, m/p-xylene and o-xylene were 0.04, 0.02, 0.05, 0.01 and 0.02 ng l(-1), respectively. The proposed analytical method was successfully used for the quantification of trace BTEX in ground water. The results indicate that HS-SPME coupled to cryo-trap GC-MS is an effective tool for analysis of BTEX in water samples at the sub-ng l(-1) level.     

Headspace solid phase microextraction method for determination of triazine and organophosphorus pesticides in soil

A headspace solid phase microextraction method (HS-SPME) for simultaneous determination of five pesticides belonging to triazine and organophosphorus pesticide groups in soil samples was developed. Microextraction conditions, such as temperature, extraction time and sodium chloride (NaCl) content were investigated and optimized using 100 μ m polydimethyl-siloxane (PDMS) fiber. Detection and quantification were done by gas chromatography-mass spectrometry (GC-MS). Relative standard deviation (RSD) and recovery values for multiple analysis of soil samples fortified at 30 μ g kg^{? 1} of each pesticide were below 13 % and higher than 70 %, respectively. Limits of detection (LOD) for all the compounds studied were less than 3.2 μ g kg^{? 1}. The proposed method was applied in the analysis of some agricultural soil samples.     

Simultaneous determination of estrogenic odorant alkylphenols,chlorophenols, and their derivatives in water using online headspace solid phase microextraction coupled with gas chromatography-mass spectrometry

A simple online headspace solid-phase microextraction (HS-SPME) coupled with the gas chromatography-mass spectrometry (GC-MS) method was developed for simultaneous determination of trace amounts of nine estrogenic odorant alkylphenols and chlorophenols and their derivatives in water samples. The extraction conditions of HS-SPME were optimized including fiber selection, extraction temperature, extraction time, and salt concentration. Results showed that divinylbenzene/Carboxen/polydimethylsiloxane (DVB/CAR/PDMS) fiber was the most appropriate one among the three selected commercial fibers, and the optimal extraction temperature, time, and salt concentration were 70 °C, 30 min, and 0.25 g/mL, respectively. The developed method was validated and showed good linearity (R ²?>?0.989), low limit of detection (LOD, 0.002–0.5 μg/L), and excellent recoveries (76–126 %) with low relative standard deviation (RSD, 0.7–12.9 %). The developed method was finally applied to two surface water samples and some of these target compounds were detected. All these detected compounds were below their odor thresholds, except for 2,4,6-TCAS and 2,4,6-TBAS wherein their concentrations were near their odor thresholds. However, in the two surface water samples, these detected compounds contributed to a certain amount of estrogenicity, which seemed to suggest that more attention should be paid to the issue of estrogenicity rather than to the odor problem.     

Use of pine needles as an indicator of atmospheric contamination by pentachlorophenol

The use of pine needles as an inexpensive and natural device for collecting atmospheric organic contaminants was investigated. The widespread existence of pentachlorophenol in the atmosphere was investigated by analyzing pine needle extracts by GC-MS. PCP was found at low ppb levels in all pine needle samples which were analyzed.     

Determination of pentachlorophenol (PCP) in waste wood--method comparison by a collaborative trial

Two independently developed and validated procedures for the determination of pentachlorophenol (PCP) in waste wood were compared by means of a collaborative trial. Both methods foresee quantification of PCP by gas chromatography (GC-ECD) after acetylation and differ with regard to the use of methanol or toluene/sulphuric acid, respectively, as solvent in the sonication extraction step. Test samples with established analyte homogeneity were prepared from a ground "real life" starting material. A total of 23 participating laboratories with experience in wood preservative analysis were instructed to apply both methods to three levels of content in the range of 0.5-20 mg PCP/kg. In case of the toluene/sulphuric acid extraction, lower recoveries and higher interlaboratory dispersion of results at the higher PCP contents were observed. Seen against the background of the Horwitz equation a reproducibility standard deviation of approximately 19% for the methanol extraction at the 4.5 mg/kg level meets the requirement for a sound analytical method. Thus, the sonication extraction procedure with methanol has been annexed as a reference method to the German waste wood regulation.     

Sorption of pentachlorophenol on surficial sediments: the roles of metal oxides and organic materials with co-existed copper present

The sorption characteristics of pentachlorophenol (PCP) in the surficial sediments were investigated using a selective extraction procedure. The results show that the Gamma(max) of PCP sorption decreased from 1.60mumolg(-1) to 0.69mumolg(-1) by approximately 60% after selective removal of organic materials from the sediments. The sorption of PCP in the sediments after selective removal of Mn oxides increased nearly up to 600% (from 1.60mumolg(-1) to 11.11mumolg(-1)) and, to a less degree, the PCP sorption in the sediments after simultaneous removal of Fe/Mn oxides (Gamma(max)=3.53mumolg(-1)). The analysis of the data using an additional model indicates that the contribution of Mn oxides to PCP sorption was negative, and Fe oxides and organic materials both have greater potential for sorption of PCP with less contribution from residues including Mn and Fe oxides in the residual fractions determined by a sequential extraction procedure and clay and silicate minerals. The differences in the decreased degrees of PCP sorption with increasing of Cu suggest that competition between Cu and PCP for sorption sites mainly takes place on Fe oxides.     

Detection and occurrence of pentachlorophenol residues in chicken liver and fat

A method for the detection of pentachlorophenol (PCP) residues in chicken liver and fat is presented. A detection limit of 0.002 mg/kg was achieved. Recoveries from liver and fat were in the range 82-88% and 95-97%, respectively. Low level residues of PCP were found in all 1072 liver and 723 fat samples. These levels were less than 0.010 mg/kg in 92.7% of the fat and 75.6% of the livers. Only 0.75% of the liver samples had PCP levels greater than 0.1 mg/kg. None of the more toxic impurities of PCP were detected in the chicken tissues.     

再生水中消毒副产物——卤乙酸的测定方法研究

参照美国国家环保局(USEPA)推荐的饮用水卤乙酸类消毒副产物测定方法(Method 552.3),通过优化该方法的预处理条件和改变检测方法,提出了酸化萃取-衍生化-中和萃取-GC-MS测定再生水中卤乙酸含量的分析方法,并分析了北方某市再生水中4种卤乙酸类消毒副产物含量。结果表明,该方法适用于我国再生水水质,能够有效地消除再生水中共存污染物的干扰;其相对标准偏差(n=7)小于10%,方法的精密度较好;检出限与USEPA方法基本一致;样品加标回收率满足USEPA 6251B标准方法中(100±30)%要求;再生水中的卤乙酸比自来水高出几十倍,对环境和人类存在一定的潜在危害。     

Fate and effects of pentachlorophenol in hard- and soft-water microcosms

The influence of hard water and soft water on the fate and effects of pentachlorophenol (PCP) was investigated in small microcosms. Minor differences in the fate of PCP and minor changes in microcosm structure were noted between the hard- and soft-water systems. Definite differences between hard-and soft-water systems were detected in dissolved oxygen production and dissolved silica concentration at an exposure concentration of 4 mg 1⁻¹ PCP.     

Octachlorodibenzo-p-dioxin in wood treatment materials and treated wood

The octachlorodibenzo-p-dioxin (OCDD) concentrations have been determined in aged samples of commercial pentachlorophenol (PCP), in wood protection formulations containing PCP and in wood treated with PCP as a preservative or as an anti-sapstain treatment. The concentrations of OCDD found in the various samples are within the range expected from the amount of commercial PCP initially present in the samples. In view of the known stability of OCDD the results are interpreted as indicating that the formulation, treatment and ageing processes have not led to any substantial conversion of PCP to OCDD; although one result indicates that outdoor exposure of treated samples increased the OCDD concentration by a factor of approximately 2 after $\text{3}\text{1}\text{2}$ years. Analysis of aged samples of treated wood indicate that OCDD is lost much less rapidly from the wood than PCP.     

Microtox testing of pentachlorophenol in soil extracts and quantification by capillary electrochromatography (CEC)--a rapid screening approach for contaminated land

An approach to rapid soil testing which involved the use of simple solvent extraction methods was developed. The analytes of interest were priority pollutants of low water solubility which could not be readily removed from the soil using water. Direct toxicity testing of the soil samples by Microtox showed a high background toxicity which prevented realistic toxicity data from being obtained for the contaminants present. A range of different extraction solutions was used in an attempt to extract the contaminants while eliminating the matrix effects of the soil. It was necessary that the solvents selected for extraction of the soil samples were not of significant toxicity, as this could potentially mask the toxic effects of any compounds extracted from the soil. The extraction efficiencies of solvent systems were evaluated using pentachlorophenol (PCP) as a model compound of known toxicity in the Microtox assay. A rapid and cost-effective method was developed in order to determine the amount of PCP recovered from the soil by the extraction solvents employed. This method consisted of a solid phase extraction (SPE) step followed by quantification using capillary electrochromatography (CEC). Recoveries were greater when a higher proportion of organic solvent (methanol) was used in the extraction process, and lowest when water was used. An extraction based on water could provide information on the potential for leaching of contaminants from the soil into nearby water bodies in an environmental setting. An organic solvent extraction method could indicate how much toxicity soil-dependent organisms might be exposed to through ingestion. Extraction based on 50% (v/v) methanol in water was considered to be the most suitable overall extraction solution for soil screening, given that this permitted extraction of the water-insoluble compound PCP at a level which was clearly toxic in the Microtox assay while also retaining the capability to extract water-soluble contaminants.     

Distribution and bioconcentration potential of the environmental chemical pentachlorophenol (PCP) in different tissues of humans

The bioconcentration factors (BCFs) of pentachlorophenol (PCP) in different tissues, organs and body fluids of humans were calculated by two methods: 1) from daily intake of PCP and its measured concentrations in different tissues and, 2) from measured half-life and measured PCP concentrations in the human body at steady state using a linear one compartment pharmacokinetic model. The BCFs (based on wet weight) in liver, brain, blood, spleen and adipose tissue of humans as calculated by method 1 were 5.7, 3.3, 1.4, 1.4, and 1.0, respectively. The figures obtained by method 2 were in good agreement to those obtained by method 1.     

Detection of pentachlorophenol and its glucuronide and sulfate conjugates in fish bile and exposure water

The glucuronide and sulfate conjugates of pentachlorophenol (PCP) that were present in the bile and exposure water of goldfish (Carassius auratus) were used to develop methodology to quantify PCP and its metabolites. Reverse phase HPLC with radioactivity detection separated PCP and its metabolites, and was used to verify a method of quantification that used differential extraction and scintillation counting. Extractions of aqueous phase at pH 2 or 8, with butanol, ethyl acetate, or ether indicated that ether at pH 8 best separated PCP from its metabolites. The sulfate conjugate of PCP was the major metabolite produced when goldfish were exposed to 125 micrograms 14C-PCP/l. It was present primarily in the exposure water, but also appeared in the bile.     

Photocatalytic degradation of pentachlorophenol on TiO2 sol-gel catalysts

The photocatalytic degradation of pentachlorophenol (PCP) in aqueous solution was investigated using TiO2 catalysts. The samples were prepared by the sol-gel method using different gelation pH and different calcination temperatures. The solids were characterized by specific surface area, X-ray diffraction, UV-Vis absorbance, FTIR and pentachlorophenol adsorption. The catalytic activity of the solids was evaluated in a conventional photoreactor at 298 K using 30 ppm of pentachlorophenol. It was found that the reaction follows a first-order reaction and the kinetic constant values change slightly with the pH of gelation and more significantly with the calcination temperature.     

Inefficiency of Mycobacterium chlorophenolicum PCP-1 to enhance mineralization of pentachlorophenol in soil microcosms

We examined the mineralization of pentachlorophenol (PCP) in sterile and non-sterile soil with or without added bacteria (Mycobacterium chlorophenolicum PCP-1). The soil used had no history of PCP contamination. Microcosms (30 g dry weight of soil) were incubated with labelled PCP (6.76% 13C, a non-radioactive stable isotope, 22 mg kg-1 dry weight) for 60 days. M. chlorophenolicum PCP-1 (7.8 x 10(6) cells g-1 dry weight) was added to some samples. 50% of the PCP was mineralized in non-sterile soil with or without the exogenous bacteria. Only 5% of the PCP was mineralized in sterile soil with or without bacteria. These data suggest that the PCP was not accessible to M. chlorophenolicum and that the indigenous soil microflora can mineralize PCP.     

Effects of soil composition on solid phase microextraction determination of triazine and organophosphorus pesticides

The influence of organic matter and clay contents on headspace solid phase microextraction (HS-SPME) determination of triazine and organophosphorus pesticides in different soils was studied. The results of the study showed that content of soil organic matter dominantly participated in sorption of triazines (simazine, atrazine and prometryn) to soil, while sorption of organophosphorus pesticides (phorate and tebupirimfos) could not be explained only by contents of dominant soil sorption components (soil organic matter and clay). Sorption of all pesticides studied to different soil types was similar at their lower concentrations while the influence of soil composition was expressed at higher concentration levels. Except for phorate, the obtained sorption trends were different from those obtained by direct SPME mode (DM-SPME) and exhaustive liquid-solid extraction (LSE) method. These results indicated that most likely co-extractants from the analyzed medium complicated evaporation and diffusion of the pesticides to the PDMS fiber during HS-SPME sampling.     

Pentachlorophenol induced physiological-biochemical changes in Chlorella pyrenoidosa culture

Present study investigated physiological and biochemical changes in a green alga culture (Chlorella pyrenoidosa) upon exposure to varied concentrations of pentachlorophenol (PCP) (0, 0.4 mgL(-1), 2.5 mgL(-1) and 10 mgL(-1)). The results revealed that with the increase of PCP concentration, a decrease of the algal biomass, levels of photosynthetic pigments (chlorophyll a, b and carotenoid), soluble protein and an increase of nitrate reductase (NR) activity were observed. This suggests that the PCP may serve as an uncoupler, causing low ATP level within the algal cells and led most of the NR molecules to be in the dephosphoration state (i.e. active from). Moreover, it shows that photosynthetic pigments especially carotenoid were more sensitive indicators to indicate PCP toxicity as compared to the other parameters.     

Determination of hydrocarbons in old creosote contaminated soil using headspace solid phase microextraction and GC-MS.

Headspace solid phase microextraction (HS-SPME) has been used together with GC-MS to analyze organic substances directly in a soil, heavily contaminated with PAHs/creosote (approximately 300 mg/kg soil), from an old gaswork site in Stockholm, Sweden. The HS-SPME results, both qualitative and quantitative, were compared with traditional liquid extraction using ethyl acetate/hexane (20:80). It was shown that the concentrations determined with HS-SPME at 60 degrees C correlated well, for compounds containing up to two and three aromatic rings (naphthalenes, acenaphthene, acenaphthylene and fluorenes, while a lower concentration was obtained for phenanthrene, anthracene, fluoranthene and pyrene. The total concentrations for each compound determined with HS-SPME ranged from 2 to 25 microg/g soil. Quantification was done using standard addition of compounds directly to the soil samples. The bioavailable fraction of the compounds in the contaminated soil at 20 degrees C was analyzed using external calibration by spiking sterile uncontaminated sand (same texture and particle size as the contaminated soil but without a heavily sorbed organic fraction) with hydrocarbon standards in different concentrations. Storage of exposed fibers at 20 degrees C showed that analysis should be done within two days to make qualitative measurements and earlier (as soon as possible) for quantitative determinations.     

Enhanced photocatalysis of pentachlorophenol by metal-modified titanium (IV) oxide

The effects of four metals (Ag, Au, Pt, and Cu) doped on TiO2 on the photocatalysis of pentachlorophenol (PCP) were investigated. The results of this study indicated that all four metals-doped TiO2 catalysts were able to enhance the efficiency of PCP photocatalysis with an optimum metallic content of 0.1 wt%. For the metal-doped TiO2 samples (Au, Pt, and Cu), the patterns of light absorption were significantly extended toward visible light spectra in the wavelengths between 400 and 800 nm. The photocatalysis of PCP was pH dependent with the maximum degradation rate achieved in the solution at pH 3. The formation of chloride ion corresponded with the concentration of PCP degraded which confirmed that dechlorination was the major pathway of PCP photocatalysis. The overall toxicities of PCP samples were reduced with the extension of light exposure using the microtox test. The results of PCP photocatalysis are also discussed based on the characteristics of metal/TiO2 including X-ray differential (XRD) patterns, Brunquer Emmett Teller (BET) specific area analysis, and Ultra Violet (UV)-Vis absorption spectra.     

Mobility of polychlorinated aromatic compounds in soils contaminated with wood-preserving oil

Greater understanding of the mobility of polychlorinated aromatic compounds in soils is needed to investigate contamination and design suitable remediation strategies for sites contaminated with wood-preserving oil. The objectives of this study were (1) to develop a suitable aqueous batch extraction method for soil containing wood-preservative residues; (2) to determine partition coefficients for the primary contaminants [pentachlorophenol (PCP), polychlorinated dibenzo-p-dioxins (PCDDs), and polychlorinated dibenzofurans (PCDFS)] in oil, soil, and aqueous phases; and (3) to evaluate the potential soil migration of the primary contaminants. In a three-phase oil-soil-water mixture, PCP, PCDDs, and PCDFs were partitioned to the greatest extent in the oil phase. These results suggest that the migration of contaminants can occur in a saturated subsurface soil zone containing an oil phase at a wood-preserving site. In the absence of a free oil phase, PCDDs and PCDFs were highly partitioned onto soil and were considered non-leachable in the aqueous phase. However, PCP was considered highly leachable from contaminated soil containing only an aqueous liquid phase. Results from this study indicate that removal of any free oil phase present in subsurface soil should have highest priority during the cleanup of contaminated wood-preserving sites.