Passive air sampling theory for semivolatile organic compounds

The mathematical modelling underlying passive air sampling theory can be based on mass transfer coefficients or rate constants. Generally, these models have not been inter-related. Starting with basic models, the exchange of chemicals between the gaseous phase and the sampler is developed using mass transfer coefficients and rate constants. Importantly, the inter-relationships between the approaches are demonstrated by relating uptake rate constants and loss rate constants to mass transfer coefficients when either sampler-side or air-side resistance is dominating chemical exchange. The influence of sampler area and sampler volume on chemical exchange is discussed in general terms and as they relate to frequently used parameters such as sampling rates and time to equilibrium. Where air-side or sampler-side resistance dominates, an increase in the surface area of the sampler will increase sampling rates. Sampling rates are not related to the sampler/air partition coefficient (K(SV)) when air-side resistance dominates and increase with K(SV) when sampler-side resistance dominates.     

Passive air sampling for persistent organic pollutants: introductory remarks to the special issue

There have been a number of developments in the need, design and use of passive air samplers (PAS) for persistent organic pollutants (POPs). This article is the first in a Special Issue of the journal to review these developments and some of the data arising from them. We explain the need and benefit of developing PAS for POPs, the different approaches that can be used, and highlight future developments and needs.     

Measures of ozone concentrations using passive sampling in forests of South Western Europe

Ambient ozone concentrations were measured with passive samplers in the framework of the EU and UN/ECE Level II forest monitoring programme. Data from France, Italy, Luxembourg, Spain and Switzerland are reported for 2000-2002, covering the period from April to September. The number of plots increased from 67 in 2000 to 83 in 2002. The year 2001 experienced the highest ozone concentrations, reflecting more stable summer meteorological conditions. Average 6-month ozone concentrations above 45 ppb were measured this year in 40.3% of the plots, in contrast with the less than 21% measured in the other 2 years. Gradients of increasing ozone levels were observed from North to South and with altitude. Comments are made on the regional trends and on the time frame of the higher ozone episodes. Also, some recommendations enabling a better comparison between plots are provided.     

Passive sampling of selected endocrine disrupting compounds using polar organic chemical integrative samplers

Two types of polar organic chemical integrative samplers (pharmaceutical POCIS and pesticide POCIS) were examined for their sampling efficiency of selected endocrine disrupting compounds (EDCs). Laboratory-based calibration of POCISs was conducted by exposing them at high and low concentrations of 14 EDCs (4-alkyl-phenols, their ethoxylate oligomers, bisphenol A, selected estrogens and synthetic steroids) for different time periods. The kinetic studies showed an integrative uptake up to 28 days. The sampling rates for the individual compounds were obtained. The use of POCISs could result in an integrative approach to the quality status of the aquatic systems especially in the case of high variation of water concentrations of EDCs. The sampling efficiency of POCISs under various field conditions was assessed after their deployment in different aquatic environments.     

Passive sampling of perfluorinated acids and sulfonates using polar organic chemical integrative samplers

The applicability of a polar organic chemical integrative sampler (POCIS) for detection and determination of perfluorinated acids and sulfonates in water was studied under field conditions. Standard POCIS configurations (i.e., pharmaceutical and pesticide) were deployed in effluent from a wastewater treatment plant for 1, 2, and 3 weeks. Ten of 15 target compounds were found in POCIS, five of which were quantified in wastewater. Pest-POCIS appeared more effective for the sampling, while Pharm-POCIS had a more rapid uptake kinetic, which leads to faster saturation or equilibrium. The results showed that the pesticide configuration is probably more suitable for the sampling of this class of compounds. Based on average concentration in water over the sampling period and amount of compound adsorbed in the POCIS, we calculated sampling rates for five studied compounds and obtained values of 0.034 to 0.222 L?day^?1.     

Estimates of ozone AOT40 from passive sampling in forest sites in South-Western Europe

Weekly-fortnightly ozone (O3) concentrations measured by passive sampling at 81 forest monitoring plots in France, Italy, Spain and Switzerland over the period 2000-2002 were used to estimate the cumulative exposure index AOT40. The estimation method is based on a deterministic model which describes the O3 daily profile as a function of relative altitude (the difference between the altitude of the site and the lowest altitude within a 5 km radius) and the time of the day. Estimated AOT40 values (AOT40(e)) were evaluated against co-located automatic measurement stations and with 14 independent automatic stations located throughout Italy whose weekly mean O3 values were used to simulate passive samplers. AOT40 can be predicted by modelling passive sampling data (R2: 0.90; P<0.0001, SE of estimates: 3271 ppb h), although considerable deviations can occur for individual sites. Estimated AOT40 shows a distinct, significant latitudinal and altitudinal gradient. Taking the 3-year average as a whole, exceedance of critical level of 5000 ppb h occurs at 77-100% of the monitored sites, respectively.     

Passive sampling of selected pesticides in aquatic environment using polar organic chemical integrative samplers

Purpose  

Polar chemical integrative samplers (POCIS) were examined for their sampling efficiency of 12 pesticides and one metabolite commonly detected in surface waters. Laboratory-based calibration experiments of POCISs were conducted. The determined passive sampling rates were applied for the monitoring of pesticides levels in Lake Amvrakia, Western Greece. Spot sampling was also performed for comparison purposes.     

Passive sampling of ambient, gaseous air pollutants: an assessment from an ecological perspective

During some past two decades there has been a growing interest among air pollution-vegetation effects-scientists to use passive sampling systems for quantifying ambient, gaseous air pollutant concentrations, particularly in remote and wilderness areas. On the positive side, excluding the laboratory analysis costs, passive samplers are inexpensive, easy to use and do not require electricity to operate. Therefore, they are very attractive for use in regional-scale air quality assessments. Passive samplers allow the quantification of cumulative air pollutant exposures, as total or average pollutant concentrations over a sampling duration. Such systems function either by chemical absorption or by physical adsorption of the gaseous pollutant of interest onto the sampling medium. Selection of a passive sampler must be based on its known or tested characteristics of specificity and linearity of response to the chemical constituent being collected. In addition, the effects of wind velocity, radiation, temperature and relative humidity must be addressed in the context of absorbent/adsorbent performance and sampling rate. Because of all these considerations, passive samplers may provide under- or overestimations of the cumulative exposures, compared to the corresponding data from co-located continuous monitors or active samplers, although such statistical variance can be minimized by taking necessary precautions. On the negative side, cumulative exposures cannot identify short-term (相似文献   

Passive Sampling for Ozone

The Brigham Young University (BYU) organic sampling system (BOSS) and the high flow rate multi-system BYU organic sampling system (BIG BOSS), which use multichannel diffusion denuder sampling techniques, were both used to collect samples of atmospheric fine particulate organic material. Both systems were used at the Meadview sampling site located at the western boundary of the Grand Canyon National Park in northwestern Arizona for the Project MOHAVE summer intensive sampling program in August 1992. The concentrations of total fine particulate carbonaceous material determined by temperature programmed volatilization for BOSS collocated replicate samples were in agreement with an uncertainty of ±14%. A comparable agreement was seen between the BOSS and BIG BOSS samples. Carbonaceous material collected by the second of two sequential quartz filters was shown to have originated from organic material lost from particles during sampling. About one-half of the fine particulate organic material was lost from particles during sample collection. These semi-volatile organic compounds lost from particles during sampling were characterized by GC/MS analysis. The concentrations of n-alkanes, n-fatty acids, n-fatty methyl esters, and phthalic acid as a function of fine particulate size were obtained for compounds both retained by and lost from particles during sampling. The possible sources of fine particulate semi-volatile organic material collected at Meadview, and the particle size distribution of fine particulate organic material, n-alkanes, n-fatty acids, and n-fatty esters are discussed.     

Monitoring of ozone precursors in ambient air using pumped and diffusive sampling on the sorbent Carbopack X

EU legislation for ambient ozone concentrations puts a requirement on Member States to monitor a large set of ozone precursor species, mostly hydrocarbons. We describe an investigation into how much of this information is readily available from manual methods used routinely for benzene monitoring in the United Kingdom, using pumped or diffusive sampling of ambient air onto the sorbent Carbopack X, followed by thermal desorption and gas chromatography with a flame ionisation detector. Identifiable peaks were assessed for reliability by comparison with independent automated measurements and emissions inventories. We conclude that 21 of the 29 specified hydrocarbons can be usefully monitored without any change to the methods used.     

Passive water sampling for polynuclear aromatic hydrocarbons using lipidcontaining semipermeable membrane devices (SPMDs): Application to contaminant residence times

Lipid-containing semipermeable membrane devices are applied to the quantitative determination of the persistence of polynuclear aromatic hydrocarbons (PAH) in an irrigation water canal, a representative waterway. The uniform and reproducible sampling of the USGS design of lipid-containing SPMDs is exploited to measure PAH half-lives without requiring calculation of water concentrations. The trend in calculated PAH half-lives agrees with that expected if volatilization is a significant mechanism for loss from the canal with more volatile PAHs having shorter half-lives. The higher persistence of phenanthrene compared to anthracene is consistent with the greater stability of phenanthrene and suggests, with other physicochemical evidence, that other (reactive) mechanisms may be involved. The results of this study demonstrate the feasibility of the SPMD method for the measurement of residence times in aquatic and other compartments. Such information is essential for quantifying contaminant behavior in the environment and providing insights into contaminant fate.     

An ozone flux-response relationship for wheat

The concentrations of heavy metals in the fine fraction (<63 microm) of 19 surficial sediment samples from the border region of Baja California (Mexico) and California (USA) were determined. The concentration ranges (in microg g(-1)) of the metals were: Cu, 4.9-23; Zn, 39-188; Ni, 16-44; Cr, 56-802; Pb, 6-21; Cd, 0.08-0.64; Ag, 0.01-0.28; and Mn, 392-1506; the intervals (percentage) for Fe and Al were 1.36-4.6 and 3.61-8.55, respectively. The heavy metals in these sediments indicate a relative enrichment of Cr (>3000%), Zn (>350%), Ni (>300%) and Cu (>150%) off the wastewater outfall at Punta Bandera in Tijuana, Baja California, with respect to non-polluted sediments of the region. Pb, Cd and Ag have low concentrations off the same outfall and enrichment factors are generally lower than 300% (Pb) and lower than 150% (Cd and Ag). This suggests that these metals have a different origin, or that they are controlled by a different geochemical mechanism than the former. The concentrations of Mn, Fe and Al occurred within ranges typical for coastal areas and probably reflect the mineralogical composition of the sediments of the region.     

用于臭氧分解的负载型双金属催化剂

研究了催化剂载体外形和活性成分对催化剂性能的影响和其他污染物的反应对室内空气造成的二次污染。通过XPS分析说明了反应过程中催化剂表面发生的化学变化及反应机理。最终论述了臭氧分解的重要性以及该催化剂的高活性和长寿命。     

Reactive uptake of ozone at simulated leaf surfaces: Implications for ‘non-stomatal’ ozone flux

The reaction of ozone (O₃) with α-pinene has been studied as a function of temperature and relative humidity and in the presence of wax surfaces that simulate a leaf surface. The objective was to determine whether the presence of a wax surface, in which α-pinene could dissolve and form a high surface concentration, would lead to enhanced reaction with O₃. The reaction of O₃ itself with the empty stainless steel reactor and with aluminium and wax surfaces demonstrated an apparent activation energy of around 30 kJ mol^?1 for all the surfaces, similar to that observed in long-term field measurements of O₃ fluxes to vegetation. However, the absolute reaction rate was 14 times greater for aluminium foil and saturated hydrocarbon wax surfaces than for stainless steel, and a further 5 times greater for beeswax than hydrocarbon wax. There was no systematic dependence on either relative or absolute humidity for these surface reactions over the range studied (20–100% RH). Reaction of O₃ with α-pinene occurred at rates close to those predicted for the homogeneous gas-phase reaction, and was similar for both the empty reactor and in the presence of wax surfaces. The hypothesis of enhanced reaction at leaf surfaces caused by enhanced surface concentrations of α-pinene was therefore rejected. Comparison of surface decomposition reactions on different surfaces as reported in the literature with the results obtained here demonstrates that the loss of ozone at the earth's surface by decomposition to molecular oxygen (i.e. without oxidative reaction with a substrate) can account for measured ‘non-stomatal’ deposition velocities of a few mm s^?1. In order to quantify such removal, the effective molecular surface area of the vegetation/soil canopy must be known. Such knowledge, combined with the observed temperature-dependence, provides necessary input to global-scale models of O₃ removal from the troposphere at the earth's surface.     

Predicting ozone levels

This paper presents a statistical model that is capable of predicting ozone levels from precursor concentrations and meteorological conditions during daylight hours in the Shuaiba Industrial Area (SIA) of Kuwait. The model has been developed from ambient air quality data that was recorded for one year starting from December 1994 using an air pollution mobile monitoring station. The functional relationship between ozone level and the various independent variables has been determined by using a stepwise multiple regression modelling procedure. The model contains two terms that describe the dependence of ozone on nitrogen oxides (NOx) and nonmethane hydrocarbon precursor concentrations, and other terms that relate to wind direction, wind speed, sulphur dioxide (SO₂) and solar energy. In the model, the levels of the precursors are inversely related to ozone concentration, whereas SO₂ concentration, wind speed and solar radiation are positively correlated. Typically, 63 % of the variation in ozone levels can be explained by the levels of NOx. The model is shown to be statistically significant and model predictions and experimental observations are shown to be consistent. A detailed analysis of the ozone-temperature relationship is also presented; at temperatures less than 27 °C there is a positive correlation between temperature and ozone concentration whereas at temperatures greater than 27 °C a negative correlation is seen. This is the first time a non-monotonic relationship between ozone levels and temperature has been reported and discussed.     

Comparison of modelled and measured ozone concentrations and meteorology for a site in south-west Sweden: implications for ozone uptake calculations

Measurements of ground-level ozone concentrations and meteorology (temperature, vapour pressure deficit (VPD), solar radiation) at the monitoring site Ostad (south-west Sweden) were compared to data from the corresponding grid in the EMEP photo-oxidant model for 1997, 1999 and 2000. The influence of synoptic weather on the agreement between model and measurements was studied. Implications of differences between modelled and observed inputs for ozone flux calculations for wheat and potato were investigated. The EMEP model output of ozone, temperature and VPD correlated well with measurements during daytime. Deviations were larger during the night, especially in calm conditions, attributed to local climatological conditions at the monitoring site deviating from average conditions of the grid. These differences did not lead to significant differences in calculated ozone uptake, which was reproduced remarkably well. The uptake calculations were sensitive to errors in the ozone and temperature input data, especially when including a flux threshold.     

Impact of ozone mini-holes on the heterogeneous destruction of stratospheric ozone

A comprehensive study of ozone mini-holes over the mid-latitudes of both hemispheres is presented, based on model simulations with the coupled climate-chemistry model ECHAM4.L39(DLR)/CHEM representing atmospheric conditions in 1960, 1980, 1990 and 2015. Ozone mini-holes are synoptic-scale regions of strongly reduced total ozone, directly associated with tropospheric weather systems. Mini-holes are supposed to have chemical and dynamical impacts on ozone levels. Since ozone levels over northern mid-latitudes show a negative trend of approximately -4%/decade and since it exists a negative correlation between total column ozone and erythemally active solar UV-radiation reaching the surface it is important to understand and assess the processes leading to the observed ozone decline. The simulated mini-hole events are validated with a mini-hole climatology based on daily ozone measurements with the TOMS (total ozone mapping spectrometer) instrument on the satellite Nimbus-7 between 1979 and 1993. Furthermore, possible trends in the event frequency and intensity over the simulation period are assessed. In the northern hemisphere the number of mini-hole events in early winter decreases between 1960 and 1990 and increases towards 2015. In the southern hemisphere a positive trend in mini-hole event frequency is detected between 1960 and 2015 in spring associated with the increasing Antarctic Ozone Hole. Finally, the impact of mini-holes on the stratospheric heterogeneous ozone chemistry is investigated. For this purpose, a computer-based detection routine for mini-holes was developed for the use in ECHAM4.L39(DLR)/CHEM. This method prevents polar stratospheric cloud formation and therefore heterogeneous ozone depletion inside mini-holes. Heterogeneous processes inside mini-holes amount to one third of heterogeneous ozone destruction in general over northern mid- and high-latitudes during winter (January-April) in the simulation.     

Passive sampler for PM10-2.5 aerosol

This study investigates the use of a small passive sampler for aerosol particles to determine particulate matter (PM)10-2.5 concentrations in outdoor air. The passive sampler collects particles by gravity, diffusion, and convective diffusion onto a glass coverslip that is then examined with an optical microscope; digital images are processed with free software and the resultant PM10-2.5 concentrations determined. Both the samplers and the analyses are relatively inexpensive. Passive samplers were collocated with Federal Reference Method (FRM) samplers in Chapel Hill, NC; Phoenix, AZ; and Birmingham, AL; for periods from 5 to 15 days. Particles consisted primarily of inorganic dusts at some sites and a mix of industrial and inorganic materials at other sites. Measured concentrations ranged from < 10 microg/m3 to approximately 40 microg/m3. Overall, PM10-2.5 concentrations measured with the passive samplers were within approximately 1 standard deviation of concentrations measured with the FRM samplers. Concentrations determined with passive samplers depend on assumptions about particle density and shape factors and may also depend somewhat on local wind speed and turbulence; accurate values for these parameters may not be known. The degree of agreement between passive and FRM concentrations measured here suggests that passive measurements may not be overly dependent on accurate knowledge of these parameters.