Polycyclic aromatic hydrocarbon (PAH) emission from co-firing municipal solid waste (MSW) and coal in a fluidized bed incinerator

Polycyclic aromatic hydrocarbons (PAH) emissions from a commercial municipal solid waste incinerator (MSWI) were studied. A MSW–coal mixture and coal only were used as fuel for the fluidized bed incinerator. Seven sampling points were chosen according to the classified four PAH emission pathways: flue gas, residue, ash and water. The mixture of MSW and coal resulted in PAH emission more than that of coal only, and PAH emission increased with increasing MSW mass percentage. Calcium oxide (CaO) or calcium carbonate (CaCO₃) was added as a desulfurizer. PAH emission also changed with different desulfurizers because of their different influences on heat balance. The PAH toxic equivalent (TEQ) of all operating conditions was also examined, showing that total daily PAH emission from MSWI can be determined.     

Comparison of leaching tests to determine and quantify the release of inorganic contaminants in demolition waste

The changes in waste management policy caused by the massive generation of waste materials (e.g. construction and demolition waste material, municipal waste incineration products) has led to an increase in the reuse and recycling of waste materials. For environmental risk assessment, test procedures are necessary to examine waste materials before they can be reused. In this article, results of column and lysimeter leaching tests having been applied to inorganic compounds in a reference demolition waste material are presented. The results show a good agreement between the leaching behaviour determined with the lysimeter unit and the column units used in the laboratory. In view of less time and system requirements compared to lysimeter systems, laboratory column units can be considered as a practicable instrument to assess the time-dependent release of inorganic compounds under conditions similar to those encountered in a natural environment. The high concentrations of elements in the seepage water at the initial stage of elution are reflected by the laboratory column leaching tests. In particular, authorities or laboratories might benefit and have an easy-to-use, but nevertheless reliable, method to serve as a basis for decision-making.     

Emissions of organic micropollutants from discontinuously operated municipal waste incinerators

The emission of particles and organic micropollutants (PAH, PCDD and PCDF) was measured from three intermittently operated municipal waste incinerators of medium size. The mutagenicity of the stack gas samples were measured as well. The results show a good agreement between the PAH emitted and the mutagenicity in the stack gases, but none of these parameters correlate with the PCDD/PCDF content.     

Construction demolition wastes, Waelz slag and MSWI bottom ash: a comparative technical analysis as material for road construction

The objective of the study is to analyze the technical suitability of using secondary materials from three waste flows (construction and demolition waste (CDW), Waelz slag and municipal solid waste incineration (MSWI) bottom ash), under the regulations and standards governing the use of materials for road construction. A detailed technical characterization of the materials was carried out according to Spanish General Technical Specifications for Road Construction (PG3). The results show that Waelz slag can be adequate for using in granular structural layers, while CDW fits better as granular material in roadbeds. Likewise, fresh MSWI bottom ash can be used as roadbed material as long as it does not contain a high concentration of soluble salts. This paper also discusses the adequacy of using certain traditional test methods for natural soils when characterizing secondary materials for use as aggregates in road construction.     

Application of the US decision support tool for materials and waste management

The US Environmental Protection Agency (US EPA) launched the Resource Conservation Challenge (RCC) in 2002 to help reduce waste and move towards more sustainable resource consumption. The objective of the RCC is to help communities, industries, and the public think in terms of materials management rather than waste disposal. Reducing cost, finding more efficient and effective strategies to manage municipal waste, and thinking in terms of materials management requires a holistic approach that considers life-cycle environmental tradeoffs. The US EPA's National Risk Management Research Laboratory has led the development of a municipal solid waste decision support tool (MSW-DST). The computer software can be used to calculate life-cycle environmental tradeoffs and full costs of different waste management or materials recovery programs. The environmental methodology is based on the use of life-cycle assessment and the cost methodology is based on the use of full-cost accounting. Life-cycle inventory (LCI) environmental impacts and costs are calculated from the point of collection, handling, transport, treatment, and disposal. For any materials that are recovered for recycling, offsets are calculated to reflect potential emissions savings from use of virgin materials. The use of the MSW-DST provides a standardized format and consistent basis to compare alternatives. This paper provides an illustration of how the MSW-DST can be used by evaluating ten management strategies for a hypothetical medium-sized community to compare the life-cycle environmental and cost tradeoffs. The LCI results from the MSW-DST are then used as inputs into another US EPA tool, the Tool for the reduction and assessment of chemical and other environmental impacts, to convert the LCI results into impact indicators. The goal of this paper is to demonstrate how the MSW-DST can be used to identify and balance multiple criteria (costs and environmental impacts) when evaluating options for materials and waste management. This type of approach is needed in identifying strategies that lead to reduced waste and more sustainable resource consumption. This helps to meet the goals established in the US EPA's Resource Conservation Challenge.     

Characterisation of polycyclic aromatic hydrocarbons in flue gas and residues of a full scale fluidized bed combustor combusting non-hazardous industrial waste

This paper studies the fate of PAHs in full scale incinerators by analysing the concentration of the 16 EPA-PAHs in both the input waste and all the outputs of a full scale Fluidized Bed Combustor (FBC). Of the analysed waste inputs i.e. Waste Water Treatment (WWT) sludge, Refuse Derived Fuel (RDF) and Automotive Shredder Residue (ASR), RDF and ASR were the main PAH sources, with phenanthrene, fluoranthene and pyrene being the most important PAHs. In the flue gas sampled at the stack, naphthalene was the only predominant PAH, indicating that the PAHs in FBC’s combustion gas were newly formed and did not remain from the input waste. Of the other outputs, the boiler and fly ash contained no detectable levels of PAHs, whereas the flue gas cleaning residue contained only low concentrations of naphthalene, probably adsorbed from the flue gas. The PAH fingerprint of the bottom ash corresponded rather well to the PAH fingerprint of the RDF and ASR, indicating that the PAHs in this output, in contrast to the other outputs, were mainly remainders from the PAHs in the waste inputs. A PAH mass balance showed that the total PAH input/output ratio of the FBC ranged from about 100 to about 2600 depending on the waste input composition and the obtained combustion conditions. In all cases, the FBC was clearly a net PAH sink.     

Screening tests for hazard classification of complex waste materials – Selection of methods

In this study we describe the development of an alternative methodology for hazard characterization of waste materials. Such an alternative methodology for hazard assessment of complex waste materials is urgently needed, because the lack of a validated instrument leads to arbitrary hazard classification of such complex waste materials. False classification can lead to human and environmental health risks and also has important financial consequences for the waste owner. The Hazardous Waste Directive (HWD) describes the methodology for hazard classification of waste materials. For mirror entries the HWD classification is based upon the hazardous properties (H1–15) of the waste which can be assessed from the hazardous properties of individual identified waste compounds or – if not all compounds are identified – from test results of hazard assessment tests performed on the waste material itself. For the latter the HWD recommends toxicity tests that were initially designed for risk assessment of chemicals in consumer products (pharmaceuticals, cosmetics, biocides, food, etc.). These tests (often using mammals) are not designed nor suitable for the hazard characterization of waste materials. With the present study we want to contribute to the development of an alternative and transparent test strategy for hazard assessment of complex wastes that is in line with the HWD principles for waste classification. It is necessary to cope with this important shortcoming in hazardous waste classification and to demonstrate that alternative methods are available that can be used for hazard assessment of waste materials. Next, by describing the pros and cons of the available methods, and by identifying the needs for additional or further development of test methods, we hope to stimulate research efforts and development in this direction. In this paper we describe promising techniques and argument on the test selection for the pilot study that we have performed on different types of waste materials. Test results are presented in a second paper.As the application of many of the proposed test methods is new in the field of waste management, the principles of the tests are described. The selected tests tackle important hazardous properties but refinement of the test battery is needed to fulfil the a priori conditions.     

Behavior of PAHs from sewage sludge incinerators in Korea

Although production of sewage sludge increases every year, its proper treatment has only been recently raised as a new issue, as current landfill and ocean dumping arrangements are expected to become increasingly difficult to manage in the future. The Korean Ministry of Environment plans to diversify its processing facilities and expand its processing systems by 2011, with the purpose of processing all sludge produced in Korea. According to this plan, incineration (including incineration of municipal wastes) will process 30% of the entire sewage sludge throughout the country in 2011. This study reviews the characteristics of PAH, which is one of the organic substances found in sewage sludge during the incinerating process. The total amount of PAH produced from sewage sludge incineration was found to be 6.103 mg/kg on average, and investigation performed on 16 PAHs of inlets and outlets of the air control devices at five full-scale incineration facilities showed that concentrations of the PAHs on the inlet and on the outlet ranged from 3.926 to 925.748 microg/m(3) and from 1.153 to 189.449 microg/m(3), respectively. In the case of the incineration facility fed with municipal waste (95%) and sewage sludge (5%), the total of the PAH emissions concentration was higher than that found at the incineration facilities used exclusively to treat sewage. The combustion of waste vinyl and plastics contained in municipal waste fed into the facility might contribute to the high levels of PAHs in the stack gas. However more investigation is needed on the production mechanism of PAHs at different operating conditions of the incineration facilities, such as the types of waste, and other relevant factors.     

Correlation study of hazardous waste characteristics among various chemical processes in Republic of Korea

To harmonize with international standards, the Republic of Korea is in the process of converting its current hazardous waste classification system and setting up regulatory standards for all toxic substances present in hazardous waste. Detailed characterization of each form of hazardous waste belonging to five chemical processes and their correlations were studied. In the present work, the concentrations of 13 heavy metals, F^?, CN^?, 7 PAH compounds, total PCDD/F and 7 PCB isomers present in the hazardous waste generated among chemical processes such as synthetic rubber (SR), man-made fibers (MF), organic dyes and pigments (DP), pharmaceuticals and cosmetics were analyzed along with their leaching characteristics. Comparing all the processes, most of the heavy metal concentrations were high in SR waste. Naphthalene was the dominant PAH in most of the chemical process waste. PCDD/F concentrations of the samples were in the range of 0.001–0.003 ng I-TEQ/g. PCB isomer-101 and isomer-118 were found to be slightly higher than the permissible limit in the SR filter cake sample. SR process wastes doesn’t show any resemblance with the other process waste in either the heavy metals and PAH trend. Each sample from DP and MF were suitable only for hazardous waste landfill.     

Use of mix of clay/solid waste from steel works for civil construction materials.

The present study focuses on the use of solid waste generated by the steel works in Brazil for manufacturing clay-based structural products. The waste sample was characterized regarding chemical composition, X-ray diffraction, particle size, morphology, specific surface and plastic properties. The waste was added in gradual proportions to a kaolinitic clay from zero up to 3 wt.%. Ceramic bodies were formed by vacuum extrusion and fired at 950 degrees C. The physical-mechanical properties (linear shrinkage, water absorption, apparent density and flexural strength) of the resulting clay/solid waste mixtures were determined. In addition, leaching tests were performed according Brazilian Standards as well as a preliminary analysis of gases evolved during the thermal process. It was found that the solid waste is formed by irregular particles, ranging in size from 1 to 500 microm. The test results indicate that solid wastes generated by steel works can be used as filler in construction materials, thereby increasing reuse in an environmentally safe manner.     

Diffusion test of 20 kinds of waste molten slags and competitive materials

“Waste molten slag” is a glass-like material produced by the vitrification of solid waste or solid waste incineration residue. When using slags of this kind in a natural environment, their impact is anticipated to be at the same level as competitive or substituted materials. In this study, we made comparative evaluations between waste molten slags and competitive materials, using 20 samples in total. It was proved that release fluxes of metals from molten slags of municipal solid waste were almost at the same level as competitive or substituted materials. However, a larger impact will be caused from some types of slag that contain harmful metals in high concentrations, such as the slag from shredded automobile residues. The results of release flux showed that nearly 80% of the slope of the flux did not fit with the diffusion range. However, the linearity of every flux was extremely high, regardless of the slope.     

The treatment of infectious waste arising from home health and medical care services: present situation in Japan

The management of waste materials arising from home health and medical care services (HHMC wastes) in Japan is now receiving greater attention from governmental workers dealing with general household waste materials. In general, HHMC waste materials are collected in a mixed form, transported and disposed of along with municipal solid wastes. As a result, municipal workers are suffering needle stick accidents so that infections associated with HHMC waste materials may occur. The collection and transportation by patients and their families of HHMC waste materials with sharp-edges, such as injection needles, to medical-related facilities can prevent municipal workers from experiencing needle-prick accidents. One of the most important strategies for medical-related facilities is hence the education of patients and their families. Improved rules for handling HHMC waste materials are essential for the safe and effective management.     

Influence of marble wastes on soil improvement and concrete production

Waste marble dusts are obtained by different methods of cutting marble in marble manufacturing companies. However, environmental damage can occur from the uncontrolled spill of these waste materials in natural habitats. In this study, we investigated the utilization of waste marble in the soil improvement of clayey soils, and as a fine aggregate in concrete production. Specifically, we determined the physical, mechanical and physicochemical characteristics of clayey soils with marble dust (MD) additive. The test results showed that some improvement occurred in the behavior of clay soil. Also, the cutting waste of marble sludge can be used as a filler material instead of fine aggregate in concrete production. This will reduce the porosity of the concrete due to the filling of the pores by MD.     

Classification of waste materials using Fourier transform infrared spectroscopy and soft independent modeling of class analogy

Fourier transform infrared (FTIR) spectroscopy combined with multivariate data analysis is under development as a method to classify waste materials. The chemical composition of the sample is reflected by a series of regions of the infrared spectrum which are used as variables for multivariate data analysis. In this study, separated biowaste collection, mechanically-biologically treated waste (MBT-waste), and old landfill materials were collected to provide materials representing different stages of decomposition. A total of 819 FTIR absorbance spectra were recorded. Principal component analyses (PCA) were performed followed by soft independent modeling of class analogy (SIMCA) for classification of waste materials. Strong classification occurred for an analysis where spectral carbonate regions were included, and for another analysis when they were not. The SIMCA model enabled the differentiation and the classification of unknown samples according to the three categories in both cases. The classification methods developed here provide an assessment tool that regulatory authorities may wish to explore when assessing whether a treated waste from an uncertain process can be classed as compost or MBT-waste.     

Assessing recycling versus incineration of key materials in municipal waste: The importance of efficient energy recovery and transport distances

Recycling of materials from municipal solid waste is commonly considered to be superior to any other waste treatment alternative. For the material fractions with a significant energy content this might not be the case if the treatment alternative is a waste-to-energy plant with high energy recovery rates. The environmental impacts from recycling and from incineration of six material fractions in household waste have been compared through life cycle assessment assuming high-performance technologies for material recycling as well as for waste incineration. The results showed that there are environmental benefits when recycling paper, glass, steel and aluminium instead of incinerating it. For cardboard and plastic the results were more unclear, depending on the level of energy recovery at the incineration plant, the system boundaries chosen and which impact category was in focus. Further, the environmental impact potentials from collection, pre-treatment and transport was compared to the environmental benefit from recycling and this showed that with the right means of transport, recyclables can in most cases be transported long distances. However, the results also showed that recycling of some of the material fractions can only contribute marginally in improving the overall waste management system taking into consideration their limited content in average Danish household waste.     

Characterization of MSWI bottom ashes towards utilization as glass raw material

The characterization of the bottom ashes produced by two Portuguese municipal solid waste incinerators (MSWI) was performed with the aim of assessing the feasibility of using this waste as raw material in the production of glass that can be further processed as glass-ceramics for application in construction. Density and particle size distribution measurements were carried out for physical characterization. Chemical characterization revealed that SiO(2), a network glass former oxide, was present in a relatively high content (52-58wt%), indicating the suitability for this waste to be employed in the development of vitreous materials. CaO, Na(2)O and K(2)O, which act as fluxing agents, were present in various amounts (2-17wt%) together with several other oxides normally present in ceramic and glass raw materials. Mineralogical characterization revealed that the main crystalline phases were quartz (SiO(2)) and calcite (CaCO(3)) and that minor amounts of different alkaline and alkaline-earth aluminosilicate phases were also present. Thermal characterization showed that the decomposition of the different compounds occurred up to 1100 degrees C and that total weight loss was <10wt%. Heating both bottom ashes at 1400 degrees C for 2h resulted in a melt with suitable viscosity to be poured into a mould, and homogeneous black-coloured glasses with a smooth shiny surface were obtained after cooling. The vitrified bottom ashes were totally amorphous as confirmed by X-ray diffraction. The results from the present experimental work indicate that the examined bottom ashes can be a potential material to melt and to obtain a glass that can be further processed as glass-ceramics to be applied in construction.     

Where will large amounts of materials accumulated within the economy go? – A material flow analysis of construction minerals for Japan

For all countries analyzed so far, Material Flow Analysis/Accounting (MFA) studies indicate that the overall stock of materials within the economy is growing. Most are construction minerals such as asphalt, cement, sand and gravel, crushed stone, and other aggregates. In the analyses described in this paper, flows and stocks of construction minerals were estimated for Japan from the past to the future to elucidate: (1) the mechanisms by which construction minerals become waste, and (2) the future supply of and demand for recycled crushed stone. The following conclusions were drawn: (1) The amounts of waste construction minerals generated have been and will be at much lower levels than the domestic demand for construction minerals. These differences might indicate consistent growth of the stock of construction minerals, which will become waste in the future. However, certain amounts of materials that we account for as stock can be interpreted already in the environment as dead stock or dissipated waste; such materials can be called "missing stock" or "dissipated stock". Capturing that missing or dissipated stock is very important because it provides information that clarifies the environmental impacts and loss of resources that these materials cause; it allows estimation of appropriate future waste generation. (2) The amount of construction minerals that are recognized as waste was estimated to increase in the future. An imbalance in the supply of and demand for recycled crushed stone will likely occur in the near future if an expected decline in future road construction is considered.     

Carbon speciation in ash, residual waste and contaminated soil by thermal and chemical analyses

Carbon in waste can occur as inorganic (IC), organic (OC) and elemental carbon (EC) each having distinct chemical properties and possible environmental effects. In this study, carbon speciation was performed using thermogravimetric analysis (TGA), chemical degradation tests and the standard total organic carbon (TOC) measurement procedures in three types of waste materials (bottom ash, residual waste and contaminated soil). Over 50% of the total carbon (TC) in all studied materials (72% in ash and residual waste, and 59% in soil) was biologically non-reactive or EC as determined by thermogravimetric analyses. The speciation of TOC by chemical degradation also showed a presence of a non-degradable C fraction in all materials (60% of TOC in ash, 30% in residual waste and 13% in soil), though in smaller amounts than those determined by TGA. In principle, chemical degradation method can give an indication of the presence of potentially inert C in various waste materials, while TGA is a more precise technique for C speciation, given that waste-specific method adjustments are made. The standard TOC measurement yields exaggerated estimates of organic carbon and may therefore overestimate the potential environmental impacts (e.g. landfill gas generation) of waste materials in a landfill environment.     

Chemical-mechanical characteristics of crushed oyster-shell

Enormous amount of oyster-shell waste has been illegally disposed at oyster farm sites along the southern coast of Korea. To seek for a possibility to recycle the waste as construction materials, chemical and mechanical characteristics of crushed oyster-shell were investigated. Chemical and microstructure analyses showed that oyster-shells are predominantly composed of calcium carbonate with rare impurities. Compressive strength tests for soil mortar specimens with varying blending ratio of cement, water, sand, and oyster-shell were compared with normal cement mortar. There was no significant reduction in the compressive strength up to 40% of dosages of oyster-shell instead of sand. The experimental results demonstrate that oyster-shells can be resources of pure calcareous materials and effective in replacement of sand, indicating promising reusable construction materials.