旋转填充床吸收模拟工业废气中SO2的研究

选择3%SO2作为模拟工业废气,一乙醇胺（MEA）作为吸收剂在超重力条件下对模拟工业废气中脱硫工艺进行了实验研究,考察了旋转填充床转速、气液比、吸收剂入口温度以及吸收剂浓度对脱硫率的影响,确定了MEA作为吸收剂时适宜的操作条件。同时在旋转填充床中考察了几种不同吸收剂对3%SO2脱除率的影响。研究表明,1 mol/L哌嗪（PZ）的脱除率最优,1 mol/L N-甲基乙醇胺（MDEA）的脱除率最低。     

旋转填充床吸收模拟工业废气中SO2的研究

选择3%SO2作为模拟工业废气,一乙醇胺(MEA)作为吸收剂在超重力条件下对模拟工业废气中脱硫工艺进行了实验研究,考察了旋转填充床转速、气液比、吸收剂入口温度以及吸收剂浓度对脱硫率的影响,确定了MEA作为吸收剂时适宜的操作条件.同时在旋转填充床中考察了几种不同吸收剂对3%SO2脱除率的影响.研究表明,1 mol/L哌嗪...     

Enhanced sludge solubilization by microbubble ozonation

A microbubble ozonation process for enhancing sludge solubilization was proposed and its performance was evaluated in comparison to a conventional ozone bubble contactor. Microbubbles are defined as bubbles with diameters less than several tens of micrometers. Previous studies have demonstrated that microbubbles could accelerate the formation of hydroxyl radicals and hence improve the ozonation of dyestuff wastewater. The results of this study showed that microbubble ozonation was effective in increasing ozone utilization and improving sludge solubilization. For a contact time of 80 min, an ozone utilization efficiency of more than 99% was obtained using the microbubble system, while it gradually decreased from 94% to 72% for the bubble contactor. The rate of microbial inactivation was obviously faster in the microbubble system. At an ozone dose of 0.02 g O₃ g⁻¹ TSS, about 80% of microorganisms were inactivated in the microbubble system, compared with about 50% inactivation for the bubble contactor. Compared to the bubble contactor, more than two times of COD and total nitrogen, and eight times of total phosphorus content were released from the sludge into the supernatant by using the microbubble system at the same ozone dosage. The application of microbubble technology in ozonation processes may provide an effective and low cost approach for sludge reduction.     

The use of nanovermiculite catalyst in the study of removal of the organic load and degradation of atrazine via ozone process in RPB reactor

Abstract

The main objective of this study is the degradation of a synthetic solution of atrazine by a modified vermiculite catalyzed ozonation, in a rotating packed bed (RPB) reactor. A 0.5?L RPB reactor was used to perform the experiments, using a Central Composite Design (CCD) response surface to construct the quadratic model based on the factors: pH, catalyst concentration and reactor rotation frequency. The response variable was the removal of the organic load measured in terms of Chemical Oxygen Demand (COD). After the complete quadratic model was constructed through the response surface, the COD degradation process had an optimal removal of 41% under the following conditions: pH 8.0, rotation of 1150?rpm and catalyst concentration 0.66?g L^?1.     

旋转填料床/柠檬酸盐法吸收-解吸SO2

提出采用旋转填料床结合柠檬酸盐法脱除烟气中SO2的方法,考察了旋转填料床转子转速、液气比、初始柠檬酸根浓度和初始pH值等因素对脱硫效率的影响。结果表明,采用超重力法超重机转子转速为1 000 r/min、液气比为7L/m3、初始柠檬酸根浓度为1.5 mol/L、吸收液的初始pH值为5.0,脱硫效率稳定在99%左右。研究了水蒸气汽提法解吸SO2时初始柠檬酸根浓度、初始pH值、SO2浓度、富液流量和水蒸气流量对解吸效率的影响,得出了影响SO2解吸率的基本规律,并进行了分析。通过实验证明该方法在技术上是可行的,具有良好的应用前景。     

复合纳米Fe2O3/TiO2可见光催化降解邻甲酚溶液的研究

以复合纳米Fe2O3／TiO2作为催化剂,日光色镝灯为光源,研究了邻甲酚溶液的可见光降解。考察了催化剂制备方法、催化剂使用量、溶液pH、催化剂重复使用等条件对可见光降解的影响。实验结果表明,1％Fe2O3／TiO2（n）对邻甲酚溶液的可见光降解效果最优,比Ti02（p25）的降解率提高了2．6倍。在实验条件下,可见光降解3h,邻甲酚溶液的浓度去除率达95．4％,TOC去除率为72．3％。在较宽的浓度范围内,邻甲酚的反应服从一级动力学反应方程,随着浓度的增大,反应速率常数不断降低。     

超重力-磷酸钠法脱除低浓度SO2

为开发脱硫率高、成本低、可回收SO2的脱硫技术,以旋转填料床为吸收设备,磷酸钠溶液为吸收剂,系统开展了液气比L／G、转速N、气体中SO2浓度CSO2,in吸收剂磷酸浓度CL和初始pH等工艺参数和溶液再生循环次数对脱硫率叼影响的实验研究。结果表明,叩随L／G、N、CL和初始pH的增加而增大,且它们的值越低时,叩增加越明显;受G和CSO2,in影响较小。在适宜操作条件下,脱硫率达99％以上,出口SO2浓度低于100mg／m^3。磷酸钠溶液可再生循环使用,脱硫率稳定在99％以上。表明超重力-磷酸钠法脱硫技术在小的液气比下即可达到高的脱硫率,吸收剂循环使用,可实现低成本并达标治理SO2废气,且适用范围宽,具有良好的工业应用前景。     

超重力脱除模拟烟气中一氧化氮简

以NO和N₂的混合气作模拟烟气,以酸性尿素溶液为吸收剂,在超重力机中进行了脱除模拟烟气中NO实验研究。实验考察了混合气中NO初始含量、进气流量、吸收液流量、超重力机转速对NO脱除率的影响,确定了在超重力中尿素吸收NO的适宜条件。实验结果表明,在常温常压下,N₂体积流量为1.0 m³/h,控制NO初始浓度为3 300 mg/m³,吸收液流量为250 L/h,超重力机转速为650 r/min时,NO脱除率可达89.5%。     

填料-生物转盘处理有机模拟污水

针对传统生物转盘启动慢、挂膜性能差、水力停留时间长等缺点,采用英国某生物技术公司研制的新型填料复合式生物转盘处理有机模拟污水,考察水力停留时间、转盘转速、有机负荷等因素对工艺运行效果的影响。结果表明,新型生物转盘启动快,微生物相变化明显,微生物量大,挂膜效率高;抗负荷冲击能力强,有机负荷大幅度变化对其影响较小;二级转笼处有机负荷相对较低,溶解氧高,微生物的种类、数量均比一级转笼多;该转盘处理有机模拟污水的最优水力停留时间为1.5 h,最佳转速为12.4 r/min,较传统生物转盘污水处理量大,且污水COD去除率高达97%,大大降低运行能耗,出水水质达到城镇污水处理厂污染物排放标准(GB18918-2002)中的一级A标准。     

铁及铁铜氧化物对臭氧氧化酸性红B的催化效能

采用自蔓延溶胶凝胶法分别制备了铁氧化物和铁铜复合氧化物催化剂,以酸性红B为降解对象,对比了单独臭氧氧化、铁氧化物和铁铜复合氧化物催化臭氧氧化对酸性红B的降解效果,考察了磁力搅拌速度(500～1 640 r/min)、溶液pH(3～11)、臭氧投加速率(3.55～28.4 mg/min)对铁铜复合氧化物催化性能的影响。结果表明,与单独臭氧氧化比较,铁氧化物和铁铜复合氧化物均能加速酸性红B的降解,促进色度和COD的去除,结合催化剂的表征结果,推断催化剂表面羟基促进臭氧分解产生.OH是其氧化性能较好的主要原因,另外,催化剂的吸附能力对催化性能也有一定影响。随着磁力搅拌速度、溶液pH、臭氧投加速率的增大,铁铜复合氧化物催化臭氧氧化酸性红B的效果越好。     

Photodecomposition of o-cresol by UV-LED/TiO2 process with controlled periodic illumination

This study investigated the effect of controlled periodic illumination on the photonic efficiency and temporal decomposition behavior of o-cresol by UV/TiO2 process in a slurry reactor using light emitting diodes as the light source. Based on the same UV light intensity of 6.7 W m(-2), the calculated photonic efficiencies increased from 1.5% to 6.3% with the decreasing duty cycle from 1.0 to 0.1 possibly ascribed to the decreasing electron-hole recombination. Actually, the calculated photonic efficiency under periodic illumination at sufficiently intermittence was inferior to, but approached, those under continuous illumination at equivalent average UV light intensity. The calculated electric energy per order increased from 32 to 37 k W h m(-3)order(-1) for experiments conducted with the increasing duty cycle from 0.1 to 1.0, and the electric energy consumption decreased significantly due to the lower duty cycle and average UV light intensity. The photocatalytic decomposition of o-cresol with the UV-light emitting diodes light could be well modeled by the Langmuir-Hinshelwood kinetic equation.     

Decomposition of 2-mercaptothiazoline in aqueous solution by ozonation

This study investigates the ozonation of 2-mercaptothiazoline (2-MT). The 2-MT is one of the important organic additives for the electroplating solution of the printed wiring board industry and has been widely used as a corrosion inhibitor in many industrial processes. It is of concern for the aquatic pollution control especially in the wastewaters. Semibatch ozonation experiments in the completely stirred tank reactor are performed under various concentrations of input ozone. The concentrations of 2-MT, sulfate, and ammonium are analyzed at specified time intervals to elucidate the decomposition of 2-MT during the ozonation. In addition, the time variation of the dissolved ozone concentration (C(ALb)) is continuously monitored in the course of experiments. Total organic carbon (TOC) is chosen and measured as a mineralization index of the ozonation of 2-MT. The results indicate that the decomposition of 2-MT is efficient, while the mineralization of TOC is limited via the ozonation only. Simultaneously, the yield of sulfate with the maximum value of about 47% is characterized by the increases of TOC removal and ozone consumption. These results can provide some useful information for assessing the feasibility of the treatment of 2-MT in the aqueous solution by the ozonation.     

电化学转盘/电凝聚法处理模拟活性染料废水的研究

采用一种新的电化学方法--电化学转盘/电凝聚法来处理模拟活性翠蓝KN-G废水,考察了电压、转速、pH、反应时间对色度、TOC去除率的影响,并确定了最佳反应条件.在最佳反应条件(电压12 V,转速70 r/min,pH为4～5,反应时间为60 min)下,色度和TOC去除率可分别达到95.3%和73.5%.并初步探讨了活性翠蓝KN-G的降解机理.     

多面空心球载体新型生物转笼处理生活污水性能研究

生物转盘是一种有效的生物膜法污水处理技术。对传统生物转盘进行改良,制成填料式生物转笼反应器,在转笼中投加多面空心球作为生物载体,研究该反应器对生活污水的处理效果。结果表明:转笼转速为9～12 r/min,在HRT从10 h逐级降至4.5 h的过程中,当进水COD、NH3-N和TN浓度分别为215.9～241.0 mg/L、22.1～24.0 mg/L和30.3～33.9 mg/L时,去除率分别在85.0%～90.2%,80.0%～98.3%及21.3%～34.2%之间。实验验证了该反应器用于生活污水处理的可行性,为农村小规模生活污水的有效处理提供了适用技术。     

Decomposition of benzene and toluene in air streams in fixed-film photoreactors coated with TiO2 catalyst

The decomposition of benzene and toluene in air streams by UV/TiO2 process was studied in different annular photoreactors under various operating conditions. The shells of reactors used in this research are made of stainless steel, Pyrex glass, or titanium. The TiO2 film was coated to the inner surface of the reactors by either rotating coating or sol-gel techniques. The TiO2 films coated by sol-gel technique were found to be smoother and more uniform than those coated by rotating coating. However, experimental results indicated that the photocatalysis of benzene or toluene in a glass reactor with rotating-coated TiO2 film delivered higher decompositions in air streams than that with sol-gel coated reactors. Benzene and toluene were decomposed more effectively in a coated glass reactor than in a coated stainless steel reactor under the same operating conditions. The presence of water vapor in air-stream plays an important role in the decomposition of benzene and toluene, and a relative humidity of approximately 5-6% was found to be adequate. The presence of excessive amounts of humidity retarded the decomposition to certain extents possibly results from the competitive adsorption of water molecules on the active sites of TiO2.     

Decomposition of trichloroethylene and 2,4-dichlorophenol by ozonation in several organic solvents

The effects of chemical characteristics of organic solvents on the decomposition rate constants of undissociative trichloroethylene (TCE) and dissociative 2,4-dichlorophenol (2,4-DCP) by ozonation were studied. The TCE and 2,4-DCP decomposition by ozonation in organic solvents followed to the first-order reaction kinetics with respect to TCE or 2,4-DCP concentration. The orders of the rate constants among organic solvents for undissociative TCE and dissociative 2,4-DCP were different indicating that the ozonation rates for undissociative and dissociative compounds were dependent on the chemical property of organic solvent. The decomposition of undissociative TCE by ozonation was a simple electrophilic reaction, which was dependent on acceptor number (AN) of the solvent. On the other hand, the decomposition of dissociative 2,4-DCP was dependent on by the dissociation of the compounds and would be dependent on donor number (DN) of the solvent. Finally, TCE in acetic acid was transformed to chlorinated intermediates and chloride ion and then these intermediates were continuously oxidized to chlorine gas.     

Fluorescence spectroscopic characterization of DOM fractions isolated from a filtered river water after ozonation and catalytic ozonation

Fluorescence spectra were applied to investigate the structural changes of four dominant dissolved natural organic matter (DOM) fractions of a filtered river water before and after ozonation and catalytic ozonation. The ozonation and catalytic ozonation with synthetic goethite (FeOOH) and cerium dioxide (CeO(2)) were carried out under normal conditions, i.e. pH 7, reaction time of 10 min, and ozone/DOC ratio of about 1. The fluorescence spectra were recorded at both excitation-emission matrix (EEM) and synchronous scanning modes. EEM results reveal that ozonation of these DOM fractions causes a significant decrease of the aromaticity of humic-like structures and an increase of electron withdrawing groups, e.g., carboxylic groups. The catalysts can further improve the destruction of the humic-like structures in catalytic ozonation. Synchronous spectra reveal that ozonation of hydrophobic acid and hydrophilic acid (HIA) yields a significant amount of by-products with low aromaticity and low molecular weight. Catalytic ozonation enhances substantially the formation of these by-products from HIA and improves the destruction of highly polycyclic aromatic structures for all examined DOM fractions.     

并流旋转床气体出口压降数值分析

气体出口是旋转床的重要组成部分,对旋转床流场与气相压降有着重要的影响。研究并流旋转床结构、构建气体出口物理模型,利用RNG k-ε湍流模型,探索不同气体出口结构对并流旋转床流场的影响。模拟结果表明:具有4个切向气体出口的DCRPB3615型旋转床有利于旋转床内速度分布均匀、降低湍动能,减小气相压降。模拟与实验对比表明,DCRPB3615压降比单一径向出口的CRPB3615型旋转床降低10%左右。     

Ozonation of oxytetracycline and toxicological assessment of its oxidation by-products

Antibiotic formulation effluents are well known for their difficult elimination by traditional bio-treatment methods and their important contribution to environmental pollution due to its fluctuating and recalcitrant nature. In the present study the effect of ozonation on the degradation of oxytetracycline (OTC) aqueous solution (100mgl(-1)) at different pH values (3, 7 and 11) was investigated. Ozone (11mgl(-1) corresponds the concentration of ozone in gas phase) was chosen considering its rapid reaction and decomposition rate. The concentration of oxytetracycline, chemical oxygen demand (COD), biochemical oxygen demand (BOD) and BOD5/COD ratio were the parameters to evaluate the efficiency of the ozonation process. In addition, the toxic potential of the OTC degradation was investigated by the bioluminescence test using the LUMIStox 300 instrument and results were expressed as the percentage inhibition of the luminescence of the marine bacteria Vibrio fischeri. The results demonstrate that ozonation as a partial step of a combined treatment concept is a potential technique for biodegradability enhancement of effluents from pharmaceutical industries containing high concentration of oxytetracycline provided that the appropriate ozonation period is selected. At pH 11 and after 60min of ozonation of oxytetracycline aqueous solutions (100 and 200mgl(-1)) the BOD5/COD ratios were 0.69 and 0.52, respectively. It was also shown that COD removal rates increase with increasing pH as a consequence of enhanced ozone decomposition rates at elevated pH values. The results of bioluminescence data indicate that first by-products after partial ozonation (5-30min) of OTC were more toxic than the parent compound.     

Decomposition of gas phase 1,3-butadiene by ultraviolet/ozone process

A pilot-scale plug-flow reactor was built to investigate its performance in treating airborne 1,3-butadiene (BD) via ozonation (O3) and ultraviolet (UV)/O3 technologies. Governing factors, such as the initial molar ratio of ozone to BD, UV volumetric electric input power, and moisture content in the influent airstream, were investigated. Experiments were conducted at an influent BD concentration of approximately 50 ppm, an ambient temperature of 26 degrees C, and a gas retention time of 85 sec. Results show that an initial molar ratio of ozone to BD of 3.5 and 2 sufficed to obtain BD decompositions of >90% for ozonation and UV/O3, respectively. The UV irradiance did not directly promote the decomposition of BD, rather, it played a role in promoting the production of secondary oxidants, such as hydroxyl radicals. Kinetic analyses indicate that both types of BD decomposition are peudo-first-order with respect to BD concentrations. Moisture content (relative humidity = 40-99%) and UV volumetric electric input power (0.147 and 0.294 W/L) are both factors that weakly affect the rate of BD decomposition. Economic evaluation factors, including both energy of ozone production and UV electric input power, were also estimated.