An Evaluation of the LPG Vehicles Program in the Metropolitan Area of Mexico City

ABSTRACT

The environmental agency in the metropolitan area of Mexico City has launched a program to introduce more energy-efficient modes of transport, one of which is the use of alternative and less polluting fuels. With that perspective in mind, a liquefied petroleum gas (LPG) fleet of vehicles is exempt of the mandatory "one day without a car" program if the emission of pollutants is below the standard authorized for that specific purpose. Today, about 28,000 light-duty vehicles and heavy-duty trucks circulate in the area, most of them as aftermarket converted vehicles. In this work, we evaluated regulated exhaust emission and other parameters on 134 representative vehicles of that fleet. From the data obtained, an estimate of emission factors and their contribution to the global emission in the metropolitan area is provided. It is concluded that more than 95% of the in-use vehicles using LPG presented regulated emissions which exceeded in one or more the environmental regulations values required for certification. The poor maintenance of the vehicles and the type of conversion kit installed could be the culprits of the results obtained.     

Assessment of reducing ozone forming potential for vehicles using liquefied petroleum gas as an alternative fuel

Liquefied petroleum gas (LPG) is currently used in a small fleet of taxis as an alternative fuel to gasoline in Taipei, Taiwan as part of an incentive program promoted by Taiwan EPA to improve urban air quality. Under the test procedure in accordance with the US FTP-75 protocol to simulate an average urban driving pattern, the exhaust from four LPG and four gasoline-powered vehicles was analyzed for the percent composition of NMHCs. Emission factors for individual NMHCs were apportioned from the emission factors of total hydrocarbon based on chemical composition of the exhaust from both types of vehicles. After adjusting for ozone formation potential (OFP) by maximum incremental reactivity, the average OFP for LPG vehicles was estimated to be only 52.8% (g-O₃/veh-km) of the gasoline vehicles, or 3.3% of ozone reduction in Taipei metropolitan area, should all taxis be converted to LPG fuel.Composition analysis of the local LPG revealed that propane, butane and isobutane were the three major components and negligible amounts of alkenes were also found. In addition, the leakage from a LPG service station was substantially smaller than from a gasoline service station because of the closed design with the LPG pumping systems.     

Contribution of LPG-derived emissions to air pollution in the metropolitan area of Guadalajara City

Measurements of hydrocarbon (HC) emissions generated by the use of liquefied petroleum gas (LPG) in the metropolitan area of Guadalajara City (MAG) are presented in this work. Based on measurements in the course of distribution, handling, and consumption, an estimated 4407 tons/yr are released into the atmosphere. The three most important contributors to LPG emissions were refilling of LPG-fueled vehicles and commercial and domestic consumption. The MAG shows a different contribution pattern of LPG emission sources compared with that of the metropolitan area of Mexico City (MAMC). These results show that each megacity has different sources of emissions, which provides more accurate strategies in the handling procedures for LPG to decrease the impact in O3 levels. This work represents the first evaluation performed in Guadalajara City, based on current measurements, of the LPG contribution to polluting emissions.     

Contribution of LPG-Derived Emissions to Air Pollution in the Metropolitan Area of Guadalajara City

ABSTRACT

Measurements of hydrocarbon (HC) emissions generated by the use of liquefied petroleum gas (LPG) in the metropolitan area of Guadalajara City (MAG) are presented in this work. Based on measurements in the course of distribution, handling, and consumption, an estimated 4407 tons/yr are released into the atmosphere. The three most important contributors to LPG emissions were refilling of LPG-fueled vehicles and commercial and domestic consumption. The MAG shows a different contribution pattern of LPG emission sources compared with that of the metropolitan area of Mexico City (MAMC). These results show that each megacity has different sources of emissions, which provides more accurate strategies in the handling procedures for LPG to decrease the impact in O₃ levels. This work represents the first evaluation performed in Guadalajara City, based on current measurements, of the LPG contribution to polluting emissions.     

Methods of characterizing the distribution of exhaust emissions from light-duty, gasoline-powered motor vehicles in the U.S. fleet

Mobile sources significantly contribute to ambient concentrations of airborne particulate matter (PM). Source apportionment studies for PM10 (PM < or = 10 microm in aerodynamic diameter) and PM2.5 (PM < or = 2.5 microm in aerodynamic diameter) indicate that mobile sources can be responsible for over half of the ambient PM measured in an urban area. Recent source apportionment studies attempted to differentiate between contributions from gasoline and diesel motor vehicle combustion. Several source apportionment studies conducted in the United States suggested that gasoline combustion from mobile sources contributed more to ambient PM than diesel combustion. However, existing emission inventories for the United States indicated that diesels contribute more than gasoline vehicles to ambient PM concentrations. A comprehensive testing program was initiated in the Kansas City metropolitan area to measure PM emissions in the light-duty, gasoline-powered, on-road mobile source fleet to provide data for PM inventory and emissions modeling. The vehicle recruitment design produced a sample that could represent the regional fleet, and by extension, the national fleet. All vehicles were recruited from a stratified sample on the basis of vehicle class (car, truck) and model-year group. The pool of available vehicles was drawn primarily from a sample of vehicle owners designed to represent the selected demographic and geographic characteristics of the Kansas City population. Emissions testing utilized a portable, light-duty chassis dynamometer with vehicles tested using the LA-92 driving cycle, on-board emissions measurement systems, and remote sensing devices. Particulate mass emissions were the focus of the study, with continuous and integrated samples collected. In addition, sample analyses included criteria gases (carbon monoxide, carbon dioxide, nitric oxide/nitrogen dioxide, hydrocarbons), air toxics (speciated volatile organic compounds), and PM constituents (elemental/organic carbon, metals, semi-volatile organic compounds). Results indicated that PM emissions from the in-use fleet varied by up to 3 orders of magnitude, with emissions generally increasing for older model-year vehicles. The study also identified a strong influence of ambient temperature on vehicle PM mass emissions, with rates increasing with decreasing temperatures.     

Revisiting nitrous acid (HONO) emission from on-road vehicles: A tunnel study with a mixed fleet

Nitrous acid (HONO) is an important precursor of OH radicals in the atmosphere. In urban areas, emissions from vehicles are the main source of air pollutants, including reactive nitrogen. Previously reported emission ratios of HONO (HONO/NO_x) from vehicles were measured in the late 1990s and need to be updated due to the significant changes in emission control technologies. We measured the emission ratio of a fleet of vehicles (38% diesel on average) from March 11 to 21, 2015, in a road tunnel in Hong Kong. The emission ratio of 1.24% (±0.35%) obtained is greater than the commonly adopted 0.8% or 0.3%. The elevated emission ratio is found to be related to the presence of vehicles equipped with diesel particle filters (DPFs). Positive correlation between HONO and black carbon (BC) shows that HONO and BC were emitted together, while the lack of correlation or even anticorrelation between HONO/NO_x and BC indicates that the BC-mediated conversion of NO₂ to HONO in the dark was insignificant in the immediate vicinity of the emission sources.

Implications: Vehicular emission is a key source for HONO in the urban atmosphere. However, the most commonly used emission ratio HONO/NO_x in modeling studies was measured more than 15 years ago. Our tunnel study suggests that a mixed fleet nowadays has a higher emission ratio, possibly because of the diesel particle filter (DPF) retrofit program and the growing share of Euro IV or more advanced diesel vehicles. Our study also provides new insight into the role of black carbon in HONO formation from vehicles.     

A Multipurpose Flare Stack for Control of Chemical Process Wastes

Abstract

To test the effectiveness of California’s vehicle inspection/ maintenance (I/M) program, exclusive of vehicle-owner intervention, a fleet of more than 1,100 vehicles that previously had failed California’s Smog Check test were sent to randomly selected Smog Check stations in the Los Angeles area for covert inspections and repairs. The two-speed idle test was used for repairs. For those vehicles that were repaired at the first inspection, their FTP emission reductions were 25%, 14%, and 11% for hydrocarbons (HC), carbon monoxide (CO), and nitrogen oxides (NO_x), respectively, although emissions testing for NO_x was not performed at the Smog Check stations. Idle HC and CO emissions increased for 35% and 43% of the vehicles, respectively, after repairs. This data set shows that most vehicles that fail the Smog Check inspection are only marginal emitters, with 61% and 44% of the total potential for HC and CO emission reductions, respectively, coming from only 10% of the vehicles that currently fail the inspection. When the vehicles were rank-ordered by idle emissions from dirtiest to cleanest, emission reduction costs for the highest-emitting 10% of the fleet averaged $l,100/ton and $250/ton for HC and CO, respectively, attributing all the costs to each pollutant exclusively. For the remaining vehicles, costs increased dramatically.     

Estimated Validity and Reliability of On-Board Diagnostics for Older Vehicles: Comparison with Remote Sensing Observations

ABSTRACT

Based on requirements under the Clean Air Act Amendments of 1990, most state vehicle inspection and maintenance (I/M) programs have, since 2002, replaced the tailpipe emission testing with the on-board diagnostic (OBD) II testing for 1996 model and newer vehicles. This test relies on the OBD II system to give the pass or fail result, depending on certain conditions that might cause the vehicle to emit pollution 1.5 times higher than the regulated standard. The OBD II system is a computer and sensors installed in the vehicle to monitor the emission control units and signal if there is any malfunction. As a vehicle ages, its engine, pollution control units, and OBD II system deteriorate. Because the OBD II system's durability directly influences the test outcome, it is important to examine the fleetwide trend in the OBD II test results in comparison with an alternative measure of identifying high emitting vehicles. This study investigates whether the validity and reliability of the OBD II test is related to the age of the OBD II system installed in the fleet. Using Atlanta's I/M testing records and remote sensing device (RSD) data collected during 2002–2005, this research establishes the convergent validity and interobserver reliability criteria for the OBD II test based on on-road emissions measured by RSDs. The study results show that older vehicles exhibit significantly lower RSD–OBD II outcome agreement than newer vehicles. This suggests that the validity and reliability of the OBD II test may decline in the older vehicle fleets. Explanations and possible confounding factors for these findings are discussed.

IMPLICATIONS This research demonstrates the potential worsening validity and reliability of the on-board diagnostic (OBD) II test in old vehicles. If the main source of low validity and reliability comes from the OBD II system malfunction, we expect this malfunctioning OBD II fleet will continue to grow in the future. If unchecked, the deterioration of OBD II system may impair the effort of the inspection and maintenance (I/M) program to identify high-emitting vehicles and the ultimate objective of reducing the air pollution from automobiles. This result is especially important in a regulatory context where technological and emissions standards dominate environmental policy and yet little attention is paid to the possible degradation of environmental monitors themselves.     

Modeling In-Use Vehicle Emissions and the Effects of Inspection and Maintenance Programs

Different ways for modeling the impact of vehicle emission inspection and maintenance programs on fleet hydrocarbon emissions are examined. A dynamic model is developed for forecasting fleet emissions in which individual vehicle performance is modeled as a stochastic process and vehicle emissions are tracked over time. Emissions inspection and repair are incorporated into the model, allowing for the stochastic aspects of both testing and repair. This model is compared to EPA’s model for evaluating the impact of vehicle emissions inspection and maintenance. We find that the way vehicle emission equipment deterioration overtime is modeled is important for forecasting emissions from the fleet and for assessing the success of inspection and maintenance programs. For inspection programs, we find that factors such as the proportion of vehicles tested, and repair effectiveness and duration have the greatest impact on emission reductions. The ability of different emission testing regimes to identify polluting vehicles has less impact on a program’s overall potential for emissions reduction. Policy recommendations for I&M testing and predictions of emission reduction credits from these tests will depend in important ways on the methods used in the underlying emissions models.     

Criteria and Air-Toxic Emissions from In-Use Automobiles in the National Low-Emission Vehicle Program

Abstract

The U.S. Environmental Protection Agency (EPA) implemented a program to identify tailpipe emissions of criteria and air-toxic contaminants from in-use, light-duty low-emission vehicles (LEVs). EPA recruited 25 LEVs in 2002 and measured emissions on a chassis dynamometer using the cold-start urban dynamometer driving schedule of the Federal Test Procedure. The emissions measured included regulated pollutants, particulate matter, speciated hydrocarbon compounds, and carbonyl compounds. The results provided a comparison of emissions from real-world LEVs with emission standards for criteria and air-toxic compounds. Emission measurements indicated that a portion of the in-use fleet tested exceeded standards for the criteria gases. Real-time regulated and speciated hydrocarbon measurements demonstrated that the majority of emissions occurred during the initial phases of the cold-start portion of the urban dynamometer driving schedule. Overall, the study provided updated emission factor data for real-world, in-use operation of LEVs for improved emissions modeling and mobile source inventory development.     

Criteria and air-toxic emissions from in-use automobiles in the National Low-Emission Vehicle program

The U.S. Environmental Protection Agency (EPA) implemented a program to identify tailpipe emissions of criteria and air-toxic contaminants from in-use, light-duty low-emission vehicles (LEVs). EPA recruited 25 LEVs in 2002 and measured emissions on a chassis dynamometer using the cold-start urban dynamometer driving schedule of the Federal Test Procedure. The emissions measured included regulated pollutants, particulate matter, speciated hydrocarbon compounds, and carbonyl compounds. The results provided a comparison of emissions from real-world LEVs with emission standards for criteria and air-toxic compounds. Emission measurements indicated that a portion of the in-use fleet tested exceeded standards for the criteria gases. Real-time regulated and speciated hydrocarbon measurements demonstrated that the majority of emissions occurred during the initial phases of the cold-start portion of the urban dynamometer driving schedule. Overall, the study provided updated emission factor data for real-world, in-use operation of LEVs for improved emissions modeling and mobile source inventory development.     

Particle mass emission rates from current-technology, light-duty gasoline vehicles

Now that the U.S. Environmental Protection Agency has promulgated new National Ambient Air Quality Standards for PM2.5, work will begin on generating the data required to determine the sources of ambient PM2.5 and the magnitude of their contributions to air pollution. This paper summarizes the results of an Environmental Research Consortium program, carried out under the auspices of the U.S. Council for Automotive Research. The program focused on particulate matter (PM) emissions from representative, current-technology, light-duty gasoline vehicles produced by DaimlerChrysler Corp., Ford Motor Co., and General Motors Corp. The vehicles, for the most part taken from the manufacturer's certification and durability fleets, were dynamometer-tested using the three-phase Federal Test Procedure in the companies' laboratories. The test fleet was made up of a mixture of both low-mileage (2K-35K miles) and high-mileage (60K-150K miles) cars, vans, sport utility vehicles, and light trucks. For each vehicle tested, PM emissions were accumulated over 4 cold-start tests, which were run on successive days. PM emission rates from the entire fleet (22 vehicles total) averaged less than 2 mg/mile. All 18 vehicles tested using California Phase 2 reformulated gasoline had PM emission rates less than 2 mg/mile at both low and high mileages.     

Investigating the real-world emission characteristics of light-duty gasoline vehicles and their relationship to local socioeconomic conditions in three communities in Los Angeles,California

This paper discusses results from a vehicular emissions research study of over 350 vehicles conducted in three communities in Los Angeles, CA, in 2010 using vehicle chase measurements. The study explores the real-world emission behavior of light-duty gasoline vehicles, characterizes real-world super-emitters in the different regions, and investigates the relationship of on-road vehicle emissions with the socioeconomic status (SES) of the region. The study found that in comparison to a 2007 earlier study in a neighboring community, vehicle emissions for all measured pollutants had experienced a significant reduction over the years, with oxides of nitrogen (NO_X) and black carbon (BC) emissions showing the largest reductions. Mean emission factors of the sampled vehicles in low-SES communities were roughly 2–3 times higher for NO_X, BC, carbon monoxide, and ultrafine particles, and 4–11 times greater for fine particulate matter (PM_2.5) than for vehicles in the high-SES neighborhood. Further analysis indicated that the emission factors of vehicles within a technology group were also higher in low-SES communities compared to similar vehicles in the high-SES community, suggesting that vehicle age alone did not explain the higher vehicular emission in low-SES communities.

Evaluation of the emission factor distribution found that emissions from 12% of the sampled vehicles were greater than five times the mean from all of the sampled fleet, and these vehicles were consequently categorized as “real-world super-emitters.” Low-SES communities had approximately twice as many super-emitters for most of the pollutants as compared to the high-SES community. Vehicle emissions calculated using model-year-specific average fuel consumption assumptions suggested that approximately 5% of the sampled vehicles accounted for nearly half of the total CO, PM_2.5, and UFP emissions, and 15% of the vehicles were responsible for more than half of the total NO_X and BC emissions from the vehicles sampled during the study.

Implications: This study evaluated the real-world emission behavior and super-emitter distribution of light-duty gasoline vehicles in California, and investigated the relationship of on-road vehicle emissions with local socioeconomic conditions. The study observed a significant reduction in vehicle emissions for all measured pollutants when compared to an earlier study in Wilmington, CA, and found a higher prevalence of high-emitting vehicles in low-socioeconomic-status communities. As overall fleet emissions decrease from stringent vehicle emission regulations, a small fraction of the fleet may contribute to a disproportionate share of the overall on-road vehicle emissions. Therefore, this work will have important implications for improving air quality and public health, especially in low-SES communities.     

Particulate matter speciation profiles for light-duty gasoline vehicles in the United States

Representative profiles for particulate matter particles less than or equal to 2.5 µm (PM_2.5) are developed from the Kansas City Light-Duty Vehicle Emissions Study for use in the U.S. Environmental Protection Agency (EPA) vehicle emission model, the Motor Vehicle Emission Simulator (MOVES), and for inclusion in the EPA SPECIATE database for speciation profiles. The profiles are compatible with the inputs of current photochemical air quality models, including the Community Multiscale Air Quality Aerosol Module Version 6 (AE6). The composition of light-duty gasoline PM_2.5 emissions differs significantly between cold start and hot stabilized running emissions, and between older and newer vehicles, reflecting both impacts of aging/deterioration and changes in vehicle technology. Fleet-average PM_2.5 profiles are estimated for cold start and hot stabilized running emission processes. Fleet-average profiles are calculated to include emissions from deteriorated high-emitting vehicles that are expected to continue to contribute disproportionately to the fleet-wide PM_2.5 emissions into the future. The profiles are calculated using a weighted average of the PM_2.5 composition according to the contribution of PM_2.5 emissions from each class of vehicles in the on-road gasoline fleet in the Kansas City Metropolitan Statistical Area. The paper introduces methods to exclude insignificant measurements, correct for organic carbon positive artifact, and control for contamination from the testing infrastructure in developing speciation profiles. The uncertainty of the PM_2.5 species fraction in each profile is quantified using sampling survey analysis methods. The primary use of the profiles is to develop PM_2.5 emissions inventories for the United States, but the profiles may also be used in source apportionment, atmospheric modeling, and exposure assessment, and as a basis for light-duty gasoline emission profiles for countries with limited data.

Implications: PM_2.5 speciation profiles were developed from a large sample of light-duty gasoline vehicles tested in the Kansas City area. Separate PM_2.5 profiles represent cold start and hot stabilized running emission processes to distinguish important differences in chemical composition. Statistical analysis was used to construct profiles that represent PM_2.5 emissions from the U.S. vehicle fleet based on vehicles tested from the 2005 calendar year Kansas City metropolitan area. The profiles have been incorporated into the EPA MOVES emissions model, as well as the EPA SPECIATE database, to improve emission inventories and provide the PM_2.5 chemical characterization needed by CMAQv5.0 for atmospheric chemistry modeling.     

不同类型机动车尾气中芳香烃化合物含量分析

首次对北京市9种车辆、5种燃料在不同工况下排放芳香烃化合物的特征．进行了定量研究。结果表明,车型、燃料、净化器及工况等因素对排放量产生影响,电喷车比化油器车芳香烃化合物排放量低;汽油车排放量最高,柴油车其次,LPG及CNG车排放量最低;使用净化器可以降低芳香烃排放量;不同工况对排放量的影响随车型,燃料类型的不同而不同。     

Characterization of in-use light-duty gasoline vehicle emissions by remote sensing in Beijing: impact of recent control measures

China's national government and Beijing city authorities have adopted additional control measures to reduce the negative impact of vehicle emissions on Beijing's air quality. An evaluation of the effectiveness of these measures may provide guidance for future vehicle emission control strategy development. In-use emissions from light-duty gasoline vehicles (LDGVs) were investigated at five sites in Beijing with remote sensing instrumentation. Distance-based mass emission factors were derived with fuel consumption modeled on real world data. The results show that the recently implemented aggressive control strategies are significantly reducing the emissions of on-road vehicles. Older vehicles are contributing substantially to the total fleet emissions. An earlier program to retrofit pre-Euro cars with three-way catalysts produced little emission reduction. The impact of model year and driving conditions on the average mass emission factors indicates that the durability of vehicles emission controls may be inadequate in Beijing.     

Particle Mass Emission Rates from Current-Technology,Light-Duty Gasoline Vehicles

ABSTRACT

Now that the U.S. Environmental Protection Agency has promulgated new National Ambient Air Quality Standards for PM_2.5, work will begin on generating the data required to determine the sources of ambient PM_2.5 and the magnitude of their contributions to air pollution. This paper summarizes the results of an Environmental Research Consortium program, carried out under the auspices of the U.S. Council for Automotive Research. The program focused on particulate matter (PM) emissions from representative, current-technology, light-duty gasoline vehicles produced by DaimlerChrysler Corp., Ford Motor Co., and General Motors Corp. The vehicles, for the most part taken from the manufacturer's certification and durability fleets, were dynamometer-tested using the three-phase Federal Test Procedure in the companies' laboratories. The test fleet was made up of a mixture of both low-mileage (2K-35K miles) and high-mileage (60K-150K miles) cars, vans, sport utility vehicles, and light trucks. For each vehicle tested, PM emissions were accumulated over 4 cold-start tests, which were run on successive days. PM emission rates from the entire fleet (22 vehicles total) averaged less than 2 mg/mile. All 18 vehicles tested using California Phase 2 reformulated gasoline had PM emission rates less than 2 mg/ mile at both low and high mileages.     

Characterization of In-Use Light-Duty Gasoline Vehicle Emissions by Remote Sensing in Beijing: Impact of Recent Control Measures

Abstract

China’s national government and Beijing city authorities have adopted additional control measures to reduce the negative impact of vehicle emissions on Beijing’s air quality. An evaluation of the effectiveness of these measures may provide guidance for future vehicle emission control strategy development. In-use emissions from light-duty gasoline vehicles (LDGVs) were investigated at five sites in Beijing with remote sensing instrumentation. Distance-based mass emission factors were derived with fuel consumption modeled on real world data. The results show that the recently implemented aggressive control strategies are significantly reducing the emissions of on-road vehicles. Older vehicles are contributing substantially to the total fleet emissions. An earlier program to retrofit pre-Euro cars with three-way catalysts produced little emission reduction. The impact of model year and driving conditions on the average mass emission factors indicates that the durability of vehicles emission controls may be inadequate in Beijing.     

A new approach to in-situ determination of roadside particle emission factors of individual vehicles under conventional driving conditions

A method for continuous on-road measurements of particle number emissions for both diesel- and petrol-fuelled vehicles is presented. The setup allows the determination of particle number emission factors on an individual vehicle basis by the simultaneous measurement of CO₂ and particle concentrations. As an alternative to previous measurements on the kerbside, the sample is taken directly in the street, with the advantage of sampling in-situ within the exhaust plumes of passing vehicles, allowing the separation of the individual high-concentration plumes. The method was tested in two experiments that were conducted in the Gothenburg area. In the first study, which was performed at an urban roadside, we were able to determine particle emission factors from individual vehicles in a common car fleet passing the measurement site. The obtained emission factors were of the same order of magnitude (between 1.4 × 10¹² and 1.8 × 10¹⁴ particles km^?1) as values published in the recent literature for light duty vehicles. An additional on-road experiment was conducted at a rural road with four light duty reference vehicles (three of them petrol-powered and one diesel-powered) at driving speeds of 50 and 70 km h^?1, realised with different engine speeds. The results of the traffic emission studies show that the method is applicable provided that instruments with an adequate dynamic range are used and that the traffic is not too dense. In addition, the variability in particle emissions for a specified driving condition was estimated.     

Trends of exhaust emissions from gasoline motor vehicles in the metropolitan area of Mexico city

Light duty gasoline vehicles account for most of CO, hydrocarbons and NO_x emissions to the urban environment in the metropolitan area of Mexico City. In order to ameliorate air pollution, several control measures have been imposed in the last decade, such as: up-grade of gasoline's quality, stringent environmental standards, and catalytic converters. On the other hand and from the beginning of 2001, Tier I emission standards became mandatory for all new model year sold in the country. Car manufacturers in Mexico do not guarantee the performance of their exhaust emissions systems for a given mileage. In this work, we present results on brand new vehicles that indicate that NO_x emission factors, though they are within the Tier I standard, deteriorate rapidly with the travelled distance (mileage).