Reprocessing of metallurgical slag into materials for the building industry

Several methods of reprocessing metallurgical (blast furnace) slag into materials for the building industry, based on melting aggregates with submerged combustion, were developed and tested. The first method involves melting hot slag with some additives directly in a slag ladle with a submerged gas-air burner, with the objective of producing stabilized slag or glass-ceramic. The second method involves direct draining of melted slag from a ladle into the slag receiver, with subsequent control of the slag draining into the converter where special charging materials are added to the melt, with the objective of producing glass-ceramic. A third method involves melting cold slag with some additives inside a melting converter with submerged gas-air burners, with the objective of producing glass-ceramic fillers for use in road construction. Specific to the melting process is the use of a gas-air mixture with direct combustion inside the melt. This feature provides melt bubbling to help achieve maximum heat transfer from combustion products to the melt, improve mixing (and therefore homogeneity of the melt), and increases the rate of chemical reactions. The experimental data for different aspects of the proposed methods are presented. The reprocessed blast-furnace slag in the form of granules can be used as fillers for concretes, asphalts, and as additives in the production of cement, bricks and other building materials. As well, reprocessed blast-furnace slag can be poured into forms for the production of glass-ceramic tiles.     

Legislative and environmental issues on the use of ash from coal and municipal sewage sludge co-firing as construction material

For the economy of any co-firing process, it is important that the common waste management options of ash remain practical. Ash from bituminous coal combustion is typically handed to the construction industry. This paper describes the current European legislation on use of ash for construction purposes. Also, it presents an experimental study on the suitability of fly ash from combustion of mixtures of bituminous coal and municipal sewage sludge as additive to cement and concrete, and for use in open-air construction works, based on the ash chemical composition and the characteristics of the extract of the ash. Presently, two European standards forbid the use of ash from co-firing as additive to cement or concrete. This study shows that ash derived from coal and sewage sludge co-firing contains generally less unburned carbon, alkali, magnesium oxide, chlorine, and sulfate than coal ash. Only the concentration of free lime in mixed ash is higher than in coal, even though, at least up to 25% of the thermal input, still below the requirements of the standards. This ash also meets the requirements for the use of fly ash in open-air construction works--concentration and mobility of few elements--although this management option is forbidden to ash from co-firing. The leaching of Cd, Cr, Cu, Ni, Pb and Zn was investigated with three leaching tests. The concentration of these metals in the extracts was below the detection limit in most cases. The concentration of Cu and Zn in the extract from fly ash was found to increase with increasing share of sewage sludge in the fuel mixture. However, the concentration of these two metals in the extract is not regulated. This study indicates that excluding a priori the use of ash from co-firing as a suitable additive for construction material could cause an unnecessary burden on the environment, since probably ash would have to be disposed of in landfill. However, allowing this requires the modification of current European standards to include limitations on all elements and compounds, absent in coal but which might be present in other fuels, that are deleterious for the quality of construction materials.     

Environmental and economic life cycle assessment for sewage sludge treatment processes in Japan

Life cycle assessment for sewage sludge treatment was carried out by estimating the environmental and economic impacts of the six alternative scenarios most often used in Japan: dewatering, composting, drying, incineration, incinerated ash melting and dewatered sludge melting, each with or without digestion. Three end-of-life treatments were also studied: landfilling, agricultural application and building material application. The results demonstrate that sewage sludge digestion can reduce the environmental load and cost through reduced dry matter volume. The global warming potential (GWP) generated from incineration and melting processes can be significantly reduced through the reuse of waste heat for electricity and/or heat generation. Equipment production in scenarios except dewatering has an important effect on GWP, whereas the contribution of construction is negligible. In addition, the results show that the dewatering scenario has the highest impact on land use and cost, the drying scenario has the highest impact on GWP and acidification, and the incinerated ash melting scenario has the highest impact on human toxicity due to re-emissions of heavy metals from incinerated ash in the melting unit process. On the contrary, the dewatering, composting and incineration scenarios generate the lowest impact on human toxicity, land use and acidification, respectively, and the incinerated ash melting scenario has the lowest impact on GWP and cost. Heavy metals released from atmospheric effluents generated the highest human toxicity impact, with the effect of dioxin emissions being significantly lower. This study proved that the dewatered sludge melting scenario is an environmentally optimal and economically affordable method.     

钛硅分子筛催化双氧水氧化水中间甲酚

探索催化双氧水氧化去除间甲酚对开发炼油厂碱渣废水处理新技术意义重大。采用钛硅分子筛催化双氧水氧化水中间甲酚,考察了反应时间、反应温度、双氧水加入量、催化剂加入量和初始溶液pH对间甲酚去除率的影响。实验结果表明：钛硅分子筛对双氧水氧化间甲酚具有显著的催化作用;在反应时间为90 min、反应温度为80 ℃、n（H₂O₂）∶n（间甲酚）为4、催化剂加入量为1.5 g/L、初始溶液pH为1.0~11.0的条件下,间甲酚去除率约为94%,间甲酚溶液的BOD₅/COD从氧化前的0.26提高到氧化后的0.38,可生化性显著提高。     

Life cycle assessment of sewage sludge co-incineration in a coal-based power station

A life cycle assessment was conducted to evaluate the environmental and economic effects of sewage sludge co-incineration in a coal-fired power plant. The general approach employed by a coal-fired power plant was also assessed as control. Sewage sludge co-incineration technology causes greater environmental burden than does coal-based energy production technology because of the additional electricity consumption and wastewater treatment required for the pretreatment of sewage sludge, direct emissions from sludge incineration, and incinerated ash disposal processes. However, sewage sludge co-incineration presents higher economic benefits because of electricity subsidies and the income generating potential of sludge. Environmental assessment results indicate that sewage sludge co-incineration is unsuitable for mitigating the increasing pressure brought on by sewage sludge pollution. Reducing the overall environmental effect of sludge co-incineration power stations necessitates increasing net coal consumption efficiency, incinerated ash reuse rate, dedust system efficiency, and sludge water content rate.     

Synthetic aggregates from combustion ashes using an innovative rotary kiln

This paper describes the use of a number of different combustion ashes to manufacture synthetic aggregates using an innovative rotary 'Trefoil' kiln. Three types of combustion ash were used, namely: incinerated sewage sludge ash (ISSA); municipal solid waste incinerator bottom ash (MSWIBA-- referred to here as BA); and pulverised fuel ash (Pfa). The fine waste ash fractions listed above were combined with a binder to create a plastic mix that was capable of being formed into 'green pellets'. These pellets were then fired in a Trefoil kiln to sinter the ashes into hard fused aggregates that were then tested for use as a replacement for the natural coarse aggregate in concrete. Results up to 28 days showed that these synthetic aggregates were capable of producing concretes with compressive strengths ranging from 33 to 51 MPa, equivalent to between 73 and 112% of that of the control concrete made with natural aggregates.     

Characteristics of carbonized sludge for co-combustion in pulverized coal power plants

Co-combustion of sewage sludge can destabilize its combustion profile due to high volatility, which results in unstable flame. We carried out fuel reforming for sewage sludge by way of carbonization at pyrolysis temperature of 300-500 °C. Fuel characteristics of carbonized sludge at each temperature were analyzed. As carbonization temperature increased, fuel ratio increased, volatile content reduced, and atomic ratio relation of H/C and O/C was similar to that of lignite. The analysis result of FT-IR showed the decrease of aliphatic C-H bond and O-C bond in carbonization. In the analysis result of TG-DTG, the thermogravimetry reduction temperature of carbonized sludge (CS400) was proven to be higher than that of dried sludge, but lower than that of sub-bituminous coal. Hardgrove grindability index increased in proportion to fuel ratio increase, where the carbonized sludge value of 43-110 was similar or higher than the coal value of 49-63. As for ash deposits, slagging and fouling index were higher than that of coal. When carbonized sludge (CS400) and coal were co-combusted in 1-10% according to calorific value, slagging tendency was low in all conditions, and fouling tendency was medium or high according to the compositions of coal.     

Co-firing of paper mill sludge and coal in an industrial circulating fluidized bed boiler

Co-firing of coal and paper mill sludge was conducted in a 103 MWth circulating fluidized bed boiler to investigate the effect of the sludge feeding rate on emissions of SOx, NOx, and CO. The preliminary results show that emissions of SOx and Nx decrease with increasing sludge feeding rate, but CO shows the reverse tendency due to the decrease in combustion temperature caused by a large amount of moisture in the sludge. All emissions met the local environmental requirements. The combustion ashes could be recycled as feed materials in the cement manufacturing process.     

Petrogenetic characteristics of molten slag from the pyrolysis/melting treatment of MSW

MSW slag materials derived from four pyrolysis melting plants in Japan were studied from the viewpoint of petrology in order to discriminate the glass and mineral phases and to propose a petrogenetic model for the formation process of molten slag. Slag material is composed of two major components: melt and refractory products. The melt products that formed during the melting process comprise silicate glass, and a suite of minerals as major constituents. The silicate glass is essentially composed of low and high silica glass members (typically 30% and 50% of SiO(2), respectively), from which minerals such as spinels, melilite, pseudowollastonite, and metallic inclusions have been precipitated. The refractory products consist mainly of pieces of metals, minerals and lithic fragments that survived through the melting process. Investigations demonstrated that the low silica melts (higher Ca and Al contents) were produced at upper levels of high temperature combustion chamber HTCC, at narrower temperature ranges (1250-1350 degrees C), while the high silica melts formed at broader temperature ranges (1250-1450 degrees C), at the lower levels of HTCC. The recent temperature ranges were estimated by using CaOAl(2)O(3)SiO(2) (CAS) ternary liquidus diagram that are reasonably consistent with those reported for a typical combustor. It was also understood that the samples with a higher CaO/SiO(2) ratio (>0.74-0.75) have undergone improved melting, incipient crystallization of minerals, and extensive homogenization. The combined mineralogical and geochemical examinations provided evidence to accept the concept of stepwise generation of different melt phases within the HTCC. The petrogenesis of the melt products may therefore be described as a two-phase melt system with immiscible characteristics that have been successively generated during the melting process of MSW.     

Recycling of combined coal-biomass ash from electric power plant waste as a cementitious material: characteristics and improvement

Combined coal-biomass ash has an enormous impact on environmental quality near electric power plants. This paper describes an alternative to disposal in which the ash is used to produce cementitious materials. Ash was obtained from combustion of coal and biomass containing four mass ratios of anthracite, bitumen, rice husks, and eucalyptus bark. The cement-forming properties were systematically characterized including compressive strength development, durability, and expansion in water. The ash samples were ground to increase the specific surface area, and then used to partially replace ASTM Type I Portland cement in mixtures containing 15, 30, or 45 % ash by mass. The water-binder material's (Portland cement with or without combined coal-biomass ash) ratios (w/c) were held constant at 45, 55, or 65 % by mass. Types A, B, and D ash behaved similarly, while the properties of type C ash were slightly different. Increasing the ash fraction in Portland cement mixtures increased the water requirement and resulted in lower compressive strength. Thorough mechanical grinding reduced the porosity and significantly enhanced the material properties.     

Sludge as dioxins suppressant in hospital waste incineration

Nitrogen containing compounds such as ammonia, urea and amines can effectively inhibit the formation of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). Sewage sludge accumulates both sulfur and nitrogen during wastewater treatment so it could be used to reduce PCDD/Fs formation. Indeed, it is observed in this study that the gas evolving from the sludge drying process can significantly suppress chlorobenzene (CBz) and PCDD/Fs formation from fly ash collected from a hospital waste incinerator. For instance, the reduction of hexachlorobenzene (HxCBz) and PCDD/Fs amount was 92.1% and 78.7%, respectively, when the drying gas evolving from 2g sludge flew through 2g fly ash. These tests were conducted in the frame of projects devoted to hospital waste incineration. The disposal technology for hospital waste (HW), developed in this institute, features rotary kiln pyrolysis combined with post-combustion followed by flue gas cleaning. Hence, some preliminary tests were devoted to investigate dioxins suppression by co-pyrolysis and co-combustion of polyvinyl chloride (PVC) and sludge in lab scale. More experimental research will be conducted to appropriately assess these effects of sludge on PCDD/Fs emissions during co-pyrolysis/combustion of HW and sludge.     

Combustion studies of high moisture content waste in a fluidised bed

The combustion of three high moisture content waste materials in a fluidised bed combustor has been investigated and a comparison with co-firing of these materials with coal in the same combustor has been made. Waste materials burnt were olive oil waste, municipal solid waste and potato, which is representative of vegetable waste. Mixtures of up to 20% mass concentration water in the waste were fed to the combustor. Above that value the moisture content was too high to sustain combustion without addition of coal. Measurements of CO, NOx, SO2 temperatures were made and the carbon combustion efficiency evaluated. Co-firing with coal resulted in markedly higher combustion efficiencies with an increase of approximately 10-80% when burning the simulated MSW. However, this was much lower than the value of 93% when coal was burnt on its own. It was also much lower than the value obtained, average 90%, when co-firing potato and olive oil waste with coal and there was little difference in the combustion efficiency between the two types of waste and with increasing moisture content. It was concluded that the high ash content of the simulated MSW 26%, compared with 5% in the other two waste materials resulted in slower burning and consequently the char particles were elutriated from the bed without being fully burnt. In term of gaseous emissions during co-combustion, CO emission is relatively insensitive to change in waste fraction. While emission of SO2 can be reduced as the waste fraction increases as a result of fuel-S dilution. But in terms of percent fuel-S converted, it is actually increased by increasing waste fraction. Emissions of NO and N2O increase slightly with MSW fraction.     

Advanced ash management technologies for CFBC ash

The combustion of high-sulphur coal demands the reduction of sulphur emissions. The sorbent most often used in sulphur capture technology is calcium-based. Ashes from technologies such as circulating fluidized bed combustion (CFBC), therefore, contain high calcium levels. The use and disposal of these ashes poses challenges, because of highly exothermic reactions with water, high-pH leachates, and excessive expansion of solidified materials. This paper looks at the potential of two post-combustion ash treatment processes, CERCHAR hydration and AWDS disposal, in solving these challenges. A high-sulphur coal-derived CFBC ash is examined, after CERCHAR hydration treatment, in conjunction with a conventionally hydrated ash, in a range of chemical, geotechnical and utilization scenarios. The ashes are used to make no-cement and roller-compacted concrete as well as Ash Water Dense Suspensions (AWDS). The solidified mortar paste from no-cement concrete is subjected to an extensive geochemical examination to determine how solidification progresses and strength develops, from a chemical point of view.     

Leaching of wood ash products aimed for spreading in forest floors--influence of method and L/S ratio

Use of biofuels in the form of logging residues is increasing in the European countries. This intensive forestry, where entire trees are removed from the felling sites, may contribute to a negative nutrient balance in the forest soil. Recycling of ash from the combustion of clean wood fuel, sometimes in combination with limestone or additives/binders, back into the forest soil could maintain the soil nutrient reservoir intact. Before spreading ash, it is important to determine its contents and, particularly, its decomposition pattern using reliable laboratory leaching tests. In this study, mineralogy and the leaching of Na, Ca, K, Mg, Mn, Al, Cu, Fe, P, and Zn from wood ash pellets and granules, produced both from green liquor sludge and fly ash, are examined by XRD and by subjecting these substances to three different laboratory leaching tests: upflow percolation (CEN/TS 14405), batch leaching (SS-EN12457), and a new Swedish leaching test using a magnetic stirrer. Mineral phases such as quartz, ettringite, calcite, gehlenite, and aphtitalite were identified in the ash granules and in the ash/green liquor sludge granules, by means of XRD. Six additional minerals were detected in the granules of ash only, and another six in the ash/green liquor sludge granules. At L/S 2, the batch leaching test resulted in the highest amounts of elements leached and the upflow percolation test the lowest. At L/S 10, both the batch leaching test and the upflow percolation test resulted in high amounts of elements leached. The batch leaching test at L/S 10 complies quite well with the percolation test and could be suitable for ash/green liquor sludge granule evaluation in daily practice. The magnetic stirrer test seems to underestimate the release potential of elements from granules. The batch test is simple to perform, and has the ability to dissolve 70-80% of the elements with the highest mobility from the materials under study.     

Evaluating waste disposal systems

Waste disposal systems conventionally exhibit many problems, such as difficulties in finding final disposal sites for incinerator residues and the issue of how to recycle waste materials. Some new technologies have been developed to solve such problems, including ash melting and gasification melting. Furthermore, to improve the power generation efficiency of waste treatment facilities so that their energy is used more efficiently, combined stoker/gas turbine power generation (super waste power generation) technology has been developed. Through examination of two cases in this study, environmental impacts and costs were determined using lifecycle assessment (LCA) and lifecycle cost (LCC) methods in a model city. In case 1, a stoker furnace was compared to a combined stoker/gas turbine system. In case 2, a stoker furnace plus ash melting system was compared to a gasification melting system. The results demonstrate that the stoker furnace has a lower environmental impact than the combined stoker/gas turbine system in case 1, and that the stoker plus ash melting system costs less than the gasification melting system in case 2, but both systems had strong impacts on the environment.     

Co-combustion of dried sewage sludge and coal in a pulverized coal boiler

More than 1.1 million tons of municipal and industrial sewage sludge is produced annually in Poland. Most of this sewage sludge is landfilled or used for recultivation and fertilization of soil. After accession of Poland to the EU, large investments are planned for wastewater treatment, so it is expected that the amount of sewage sludge produced in Poland will grow in the near future. It is well known that the combustion of sewage sludge is becoming a more and more popular utilization method of such waste. Unfortunately, the current situation in Poland makes it impossible to incinerate the sewage sludge because of a lack of incinerators. One possible solution for Poland is the co-firing of dried sewage sludge in existing coal-fired utility boilers. This article presents results of initial Polish industrial trials of dried municipal sewage sludge and hard coal co-combustion in an OP-230 pulverized coal boiler. Such a solution was shown to be technically viable and not to require changes to the existing technological system. Cocombustion of sewage sludge with coal in power plants seems to be the best solution for sludge utilization in the near future in Poland.     

固硫灰固化焦化废水处理外排污泥

采用机械力化学法活化循环流化床燃煤固硫灰,用于固化焦化废水处理外排污泥(CWT污泥)。探讨了固硫灰活化条件,并通过XRD和FTIR分析了固硫灰固化CWT污泥中重金属的机理。实验结果表明:当m(Ca O)∶m(Ca O+固硫灰)为20%、球磨频率为40 Hz、球磨时间为2 h时,养护28 d固硫灰固化体的平均抗压强度达到72.2 MPa;当污泥掺加量为50%(w)时,养护28 d含污泥固化体的抗压强度达到8.5 MPa,固化体浸出液中Pb2+和As5+的质量浓度分别为0.177 mg/L和0.013 mg/L,均远低于GB 5085.3—2007《危险废物鉴别标准浸出毒性鉴别》的规定限值。XRD和FTIR表征结果表明,在固硫灰活化过程中,混合体系水化生成了C—S—H凝胶、斜方钙沸石和钙矾石,可通过物理包裹、吸附及离子交换的形式实现CWT污泥中Pb2+和As5+的固化/稳定化。     

Influence of flue-gas desulfurization systems on coal combustion by-product quality at kentucky power stations burning high-sulfur coal

Two Kentucky power plants burning similar blends of high-sulfur western Kentucky and southern Indiana coal provide a unique opportunity to examine the variations in coal combustion by-products due to differences in the method of wet flue-gas desulfurization (FGD). One plant employed carbide lime-based scrubbing for two units and a dual-alkali process for the third unit. The second plant employed a Mississippian limestone from Kentucky for all four units. This study provides an example of optical and SEM petrographic techniques, supplemented by chemical analyses, applied to the study of, at least from the geologic perspective, non-traditional materials. The coal sources comprise a blend of high volatile C and B bituminous, high vitrinite (85–90%, mmf), high-sulfur (> 3%, dry) coals. The fly ash is dominated by glassy phases (70–80%) with about 5–10% spinel (predominately magnetite), 3–10% quartz, and 4–10% isotropic coke comprising the remaining portion of the ash. SEM observations indicate that the glassy particles exhibit a bimodal size distribution with sub-micron glass spheres and a population of larger (several 10s of microns) spheres. The bottom ash has higher proportions of spinels and mullite, with negligible carbon forms, compared to the fly ash from the same units. Fly ashes were observed to be lower in Fe and higher in Al, Si, and S compared to the bottom ashes. Carbide lime, a by-product of acetylene manufacture, soda ash, and limestone were the reagents used in the flue-gas desulfurization processes. The primary FGD by-product is a calcium sulfite slurry which is vacuum filtered and mixed with fly ash and, usually, lime, to form a stable product for disposal. The FGD by-products have some potential, as yet unrealized, for utilization.     

LIFAC ash--strategies for management

LIFAC is a more recent addition to flue gas desulphurization methods for reducing sulphur emissions during coal combustion for the production of electricity. Ashes from the combustion of a low-sulphur lignite coal using LIFAC technology were used to evaluate different ash management strategies. The ashes, as produced and after treatment by the CERCHAR hydration process, were examined for their disposal characteristics and their utilization potential in concrete. They were also evaluated as underground disposal material using the AWDS process.