The Reduction of Stranded Oil by In Situ Shoreline Treatment Options

The Svalbard Shoreline Field Trials quantified the effectiveness of sediment relocation, mixing, bioremediation, bioremediation combined with mixing, and natural attenuation as options for the in situ treatment of oiled mixed-sediment (sand and pebble) shorelines. These treatments were applied to oiled plots located in the upper beach at three experimental sites, each with different sediment character and wave-energy exposure. Systematic monitoring was carried out over a 400-day period to quantify oil removal and to document changes in the physical character of the beach, oil penetration, oil loading, movements of oil to the subtidal environment, biodegradation, toxicity, and to validate oil-mineral aggregate formation.The results of the monitoring confirmed that sediment relocation significantly accelerated the rate of oil removal and reduced oil persistence where oil was stranded on the beach face above the level of normal wave activity. Where the stranded oil was in the zone of wave action, sediment relocation accelerated the short-term (weeks) rate of oil loss from the intertidal sediments.Oil removal rates on a beach treated by mechanical mixing or tilling were not significantly higher than those associated with natural recovery. However there is evidence that mixing/tilling may have enhanced microbial activity for a limited period by increasing the permeability of the sediment.Changes in the chemical composition of the oil demonstrated that biodegradation was significant in this arctic environment and a bioremediation treatment protocol based on nutrient enrichment effectively doubled the rate of biodegradation. However, on an operational scale, the success of this treatment strategy was limited as physical processes were more important in causing oil loss from the beaches than biodegradation, even where this oil loss was stimulated by the bioremediation protocols.     

Toxicity Evaluation with the Microtox Test to Assess the Impact of In Situ Oiled Shoreline Treatment Options: Natural Attenuation and Sediment Relocation

Changes in the toxicity levels of beach sediment, nearshore water, and bottom sediment samples were monitored with the Microtox^® Test to evaluate the two in situ oil spill treatment options of natural attenuation (natural recovery--no treatment) and sediment relocation (surf washing). During a series of field trials, IF-30 fuel oil was intentionally sprayed onto the surface of three mixed sediment (pebble and sand) beaches on the island of Spitsbergen, Svalbard, Norway (78°56^′ N, 16°45^′ E). At a low wave-energy site (Site 1 with a 3-km wind fetch), where oil was stranded within the zone of normal wave action, residual oil concentrations and beach sediment toxicity levels were significantly reduced by both options in less than five days. At Site 3, a higher wave-energy site with a 40-km wind fetch, oil was intentionally stranded on the beach face in the upper intertidal/supratidal zones, above the level of normal wave activity. At this site under these experimental conditions, sediment relocation was effective in accelerating the removal of the oil from the sediments and reducing the Microtox^® Test toxicity response to background levels. In the untreated (natural attenuation) plot at this site, the fraction of residual oil remaining within the beach sediments after one year (70%) continued to generate a toxic response. Chemical and toxicological analyses of nearshore sediment and sediment-trap samples at both sites confirmed that oil and suspended mineral fines were effectively dispersed into the surrounding environment by the in situ treatments. In terms of secondary potential detrimental effects from the release of stranded oil from the beaches, the toxicity level (Microtox^® Test) of adjacent nearshore sediment samples did not exceed the Canadian regulatory limit for dredged spoils destined for ocean disposal.     

Bioremediation of Stranded Oil on an Arctic Shoreline

The application of slow-release and soluble fertilizers proved to be an effective and environmentally benign way of stimulating oil biodegradation on an Arctic shoreline. Fertilizer application to the surface of the beach delivered nutrients to the oiled sediment beneath the beach surface. There was no significant run-off of this fertilizer to either the nearshore water or to unfertilized plots, and there were no adverse toxicological effects of the fertilizer application. The fertilizer application was followed by an increase in oxygen consumption and carbon dioxide evolution from the beach, increased microbial biomass, and significantly greater biodegradation of oil on the plots that had received fertilizer. The rate of oil biodegradation was approximately doubled over the course of a year by fertilizer applications in the first two months after the spill.Simple test kits proved adequate to monitor the fertilizer-application process in the field in a time frame that would allow the application process to be fine-tuned during treatment on a real spill. Simple test kits and portable instrumentation were useful in demonstrating the initial success of the bioremediation strategy.     

Determination of suitable TPH remediation approach via MANOVA and inferential statistics assessment

Soil contamination resulting from petroleum hydrocarbon contaminants poses a fairly substantial hazard to human health and the environment. Phytoremediation, land farming, and chemico–biological stabilization were used to treat total petroleum hydrocarbons (TPHs) and polycyclic aromatic hydrocarbons (PAHs) at a crude oil polluted soil site in Nigeria. A field pilot study was conducted by preparing nine cells with subcells attached to each serving as a control with an overall area of 1.53 m². A complete block design method was used for the study. The prepared soil sample cells were divided into three groups with each group having approximately 300 kg of soil and delineated as low, medium, and high test plots. The low samples were spiked with 6.1 kg of crude oil, the medium samples were spiked with 12.2 kg of crudeoil, and the high samples were spiked with 18.3 kg of crude oil. Each row containing three cells with low, medium, and high concentrations were treated separately using the three treatment methods. The ratio of the soil sample to the organic amendment for the treatments was 2:1. The results showed over 90% degradation in the initial concentration of TPH and PAHs across different contaminant levels except in the control subcells where only 30% of degradation was recorded. Multivariate analysis of variance was employed to assess the significant difference in each treatment group while inferential statistics using a mean performance plot was used to ascertain the optimum treatment method. Land farming, chemico–biological stabilization, and phytoremediation ranked 1, 2, and 3, respectively. In conclusion, the three treatment methods employed all degraded the contaminants (TPH and PAHs) with land farming emerging as the best method.     

An In Situ Bioreactor for the Treatment of Petroleum Hydrocarbons in Groundwater

Two pilot tests of an aerobic in situ bioreactor (ISBR) have been conducted at field sites contaminated with petroleum hydrocarbons. The two sites differed with respect to hydrocarbon concentrations. At one site, concentrations were low but persistent, and at the other site concentrations were high enough to be inhibitory to biodegradation. The ISBR unit is designed to enhance biodegradation of hydrocarbons by stimulating indigenous microorganisms. This approach builds on existing Bio‐Sep^® bead technology, which provides a matrix that can be rapidly colonized by the active members of the microbial community and serves to concentrate indigenous degraders. Oxygen and nutrients are delivered to the bioreactor to maintain conditions favorable for growth and reproduction, and contaminated groundwater is treated as it is circulated through the bed of Bio‐Sep^® beads. Groundwater moving through the system also transports degraders released from Bio‐Sep^® beads away from the bioreactor, potentially increasing biodegradation rates throughout the aquifer. Groundwater sampling, Bio‐Traps, and molecular biological tools were used to assess ISBR performance during the two pilot tests. Groundwater monitoring indicated that contaminant concentrations decreased at both sites, and the microbial data suggested that these decreases were due to degradation by indigenous microorganisms rather than dilution or dispersion mechanisms. Taken together, these lines of evidence showed that the ISBR system effectively increased the number and activity of indigenous microbial degraders and enhanced bioremediation at the test sites. © 2013 Wiley Periodicals, Inc.     

Petroleum Hydrocarbons Rhizodegradation by Sebastiania commersoniana (Baill.) L. B. SM. & Downs

Petroliferous activities in Brazil have an accelerated development in the last years. As a consequence, the incidence of environmental accidents such as oil spills and contamination of soils has increased significantly. Therefore, it is extremely necessary to develop remediation techniques with lower costs, decontamination efficiency and impact minimisation. The aim of this work was to evaluate Sebastiania commersoniana phytoremediation potential in soil contaminated by petroleum. This species, which is a native tree, was selected due to its proven capacity for surviving in areas contaminated by petroleum. Experiments were carried out with soils that were vegetated but non-contaminated, soils that were freshly contaminated (25, 50 and 75 g kg^?1) but non-vegetated, and soils that were vegetated and contaminated, samples were collected 60 and 424 days after contamination with the purpose of evaluating the percentage of petroleum degradation in relation to the time. The results obtained in the present study allow us to state that S. commersoniana proves to be tolerant to petroleum contamination with respect to plant’s growth. The degradation of petroleum hydrocarbons was evaluated by gas chromatography with a flame ionisation detector (GC-FID) equipped with a capillary column HP-5 (5% phenyl-methylpolysiloxane, 30 m; 0.25 mm; 0.25 μm). According to chromatographic analysis, samples in contact with S. commersoniana showed a significant area reduction of the hydrocarbon peaks. Analysis of the 60-day samples showed a reduction of petroleum hydrocarbons area higher than 60% and the 424-day samples showed a reduction higher than 94%, which demonstrates that a petroleum degradation process is occurring.     

Characterization of oily sludge from a wastewater treatment plant flocculation-flotation unit in a petroleum refinery and its treatment implications

Partly due to the complex and variable composition of oily sludge generated by the petroleum industry, cost-effective treatment and proper disposal pose considerable challenges worldwide. In this study, an extended component-based analysis of the oily sludge from a flocculation-flotation unit of a wastewater treatment system in a refinery in Sweden was carried out over 1 year. The heterogeneity of the oily sludge is illustrated by the wide ranges of concentrations found for different chemical components, particularly metals. Among the petroleum hydrocarbons, the most abundant compounds were nonpolar aliphatic hydrocarbons (63.7 ± 16.7 g kg⁻¹); from the benzene, toluene, ethylbenzene, and xylene group, xylenes (91–240 mg kg⁻¹) were most abundant; and among polycyclic aromatic hydrocarbons, naphthalene (25.7 ± 21.4), fluorene (27.25 ± 10.0), and phenanthrene (43.8 ± 18.4 mg kg⁻¹) were most abundant (all results in terms of dry matter). Based on the EU guidelines and the mean concentration values for metals found in the oily sludge, e.g., Pb (135.4 ± 125.8), Cu (105.2 ± 79.1), Hg (42.8 ± 31.3), Ni (320 ± 267.4), and Zn (1321.7 ± 529.9 mg kg⁻¹), disposal of oily sludge even in landfills for hazardous waste is not allowed. The organic content of the sludge can be reduced through biotreatment, but not the metal content. A multistep component-based treatment scheme is therefore needed.     

Bioremediation of Dissolved and Free Phase Oil in Wastewater from Equipment Maintenance Activities

Land treatment facilities can provide effective treatment of secondary oily wastewater from maintenance operations, particularly in arid climates. Soil and underlying groundwater from a land treatment facility, which has been operating for eight years, were analyzed to determine the effectiveness of using bioremediation for the treatment of dissolved and free‐phase oil in maintenance wastewater. The study was conducted at a mining site in Western Australia. The facility was capable of treating 140 kiloliters (kL) of oily wastewater per day. The average petroleum hydrocarbon content of the wastewater was 2 percent weight per volume (w/v) based on data available for the first five years. The soil data indicate that the land treatment process has been operating efficiently even at high wastewater loadings with maximum degradation rates of 10–242 mg/kg per day. Based on the soil data, there is no evidence of accumulation of any metal or polycyclic aromatic hydrocarbon (PAH) compounds. The land treatment facility has led to only low levels of TPH (total petroleum hydrocarbons) contamination (<4 ppm) in the underlying groundwater. However, nitrate concentrations in the groundwater were shown to increase over the first five years of the facility's operation. This article reports and discusses the operational data from the land treatment process, illustrating its effectiveness in treating oily wastewater. © 2001 John Wiley & Sons, Inc.     

Maersk Navigator oil spill in the great channel (Andaman Sea) in January 1993 and its environmental impact

Observations on oil slicks, tar residues and dissolved petroleum hydrocarbons (DPH) shortly after the oil spill resulting from the tanker accident in January 1993 showed negligible impact on the Indian EEZ of the Great Channel (Andaman Sea). DPH were between 0.31 and 1.85 μg l⁻¹ in the area examined. Tar residues were absent throughout the study area. Prevailing NE wind with resultant SW surface current appears to have pushed the oil patches out towards the open Indian Ocean.A follow-up survey of the same area was carried out in September-October 1993 and observations similar to those made during the earlier survey were recorded. The zooplankton biomass had increased considerably during the interval between the two surveys, but this was probably due to seasonal changes and natural variability.The spill did not cause any perceptible impact on the environment.     

Operation of a 27‐m3 biopile for the treatment of petroleum‐contaminated soil

Soil and groundwater contamination due to petroleum hydrocarbon spills is a frequent problem worldwide. In Mexico, even when programs oriented to the diminution of these undesirable events exist, in 2000, a total of 1,518 petroleum spills were reported. Exploration zones, refineries, and oil distribution and storage stations frequently are contaminated with total petroleum hydrocarbons (TPH); diesel fraction; gasoline fraction; benzene, toluene, ethyl benzene, and xylenes (BTEX); and polycyclic aromatic hydrocarbons (PAHs). Among the many methodologies available for the treatment of this kind of contaminated soil, bioremediation is the most favorable, because it is an efficient/low‐cost option that is environmentally friendly. This article discusses the capability of using a biopile to treat soils contaminated with about 40,000 mg/kg of TPH. Design and operation of a 27‐m³ biopile is described in this work, including microbiological and respirometric aspects. Parameters such as TPH, diesel fraction, BTEX, and PAHs considered by the U.S. Environmental Protection Agency were measured in biopile samples at 0, 2, 4, 6, 8, 10, and 22 weeks. A final average TPH concentration of 7,300 mg/kg was achieved in 22 weeks, a removal efficiency of 80 percent. © 2007 Wiley Periodicals, Inc.     

Lysinibacillus sphaericus and Geobacillus sp Biodegradation of Petroleum Hydrocarbons and Biosurfactant Production

Petroleum oil is a major driver of worldwide economic activity, but it has also created contamination problems during the storage and refining process. Also, unconventional resources are natural resources, which require greater than industry‐standard levels of technology or investment to exploit. In the case of unconventional hydrocarbon resources, additional technology, energy, and capital have to be applied to extract the gas or oil. Bioremediation of petroleum spill is considered of great importance due to the contaminating effects on human health and the environment. For this reason, it is important to reduce total petroleum hydrocarbons (TPH) in contaminated soil. In addition, biosurfactant production is a desirable property of hydrocarbon‐degrading microorganisms. Seven strains belonging to Lysinibacillus sphaericus and Geobacillus sp were selected to evaluate their ability to biodegrade TPH in the presence of toxic metals, their potential to produce biosurfactants, and their ability to improve the biodegradation rate. The seven bacterial strains examined in this study were able to utilize crude petroleum‐oil hydrocarbons as the sole source of carbon and energy. In addition, their ability to degrade crude oil was not affected by the presence of toxic metals such as chromium and arsenic. At the same time, the strains were able to reduce toxic metals concentration through biosorption processes. Biosurfactant production was determined using the drop‐collapsed method for all strains, and they were characterized as both anionic and cationic biosurfactants. Biosurfactants showed an increase in biodegradation efficiency both in liquid minimal salt medium and landfarming treatments. The final results in field tests showed an efficiency of 93 percent reduction in crude oil concentration by the selected consortium compared to soil without consortium. The authors propose L. sphaericus and Geobacillus sp consortium as an optimum treatment for contaminated soils. In addition, production of biosurfactants could have an application in the extraction of crude oil from unconventional hydrocarbon resources. © 2014 Wiley Periodicals, Inc.     

Disposal of oil in sandy coastal soils

A combination of survey and experimental studies is being conducted to determine the ecological risks associated with disposal of oiled beach material (OBM) in coastal sand dunes and dune pastures. Past incidence of burial close to shoreline spill locations was less than expected and the two sites located in Britain showed very different patterns of oil degradation and site recovery. Field scale experiments revealed that breakdown of hydrocarbons within OBM began very quickly after deposition, even in nutrient-poor sand, leading to almost complete degradation of crude oil. There appears to be no lateral or vertical loss of oil or its breakdown products and recolonization of deposited OBM does occur naturally, though supplementary planting helps in stabilizing the sand surface. The application of this method in practical terms is constrained by the availability of suitable sites where it is possible to minimize physical disturbance to dune systems by lorries or other equipment employed in the removal process.     

Petroleum biodegradation in soil: The effect of direct application of surfactants

The direct application of surfactants to petroleum-contaminated soil has been proposed as a mechanism to increase the bioavailability of insoluble compounds. Solubilization of hydrophobic compounds into the aqueous phase appears to be a significant rate limiting factor in petroleum biodegradation in soil. Nonionic surfactants have been developed to solubilize a variety of compounds, thus increasing the desorption of contaminants from the soil. In this study, laboratory scale land treatment scenarios were used to monitor the bioremediation of petroleum contaminated soils. In efforts to achieve the lowest levels of residual petroleum hydrocarbons in the soil following biotreatment, 0.5 and 1.0% (volume/weight) surfactant was blended into soils under treatment. Two soil types were studied, a high clay content soil and a sandy, silty soil. In both cases, the addition of surfactant (Adsee 799®, a blend of ethoxylated fatty acids, Witco Corporation) stimulated biological activity as indicated by increased heterotropbic colony forming units per gram of soil. However, the increased activity was not correlated with removal of petroleum hydrocarbons. The results suggest that the application of surfactants directly to the soil for the purpose of solubilizing hydropbobic compounds was not successful in achieving greater levels of petroleum hydrocarbon removal.     

Interim pump-and-treat remediation of a hydrocarbon-contaminated aquifer

The continuous and discontinuous release of petroleum hydrocarbons from an oil refinery in Alaska resulted in the contamination of an unconfined glacial outwash aquifer. Geologic conditions at the site allowed for the vertical migration of hydrocarbon product to the water table and subsequent formation of an areally extensive floating product layer. Since the petroleum hydrocarbon phase would provide a major source of BTX (benzene, toluene, xylene) contamination to the groundwater, interim product and groundwater recovery measures were initiated to limit aquifer degradation. Phase I remedial activities involved the operation of nine well pairs, with one well used for groundwater extraction and the other for product recovery. Phases II and III involved expansion of the recovery well network and use of a two-pump system. Petroleum product recovered was reprocessed at the refinery. Contaminated groundwater was initially treated using the refinery's wastewater treatment system, but treatment inefficiencies and continued system expansion necessitated use of a separate treatment unit. Performance evaluations indicate that the remedial phases have been successful in halting further contaminant migration and in recovering a significant volume of the released petroleum hydrocarbons.     

In Situ flushing of contaminated soils from a refinery: Organic compounds and metal removals

This article demonstrates the applicability of in situ flushing for the remediation of soil contaminated with petroleum hydrocarbons at a Mexican refinery. The initial average total petroleum hydrocarbon (TPH) concentration for the demonstration field test was 55,156 g/kg. After six weeks of in situ flushing with alternate periods of water and water/surfactant, an average concentration of 1,407 mg/kg was reached, achieving a total removal efficiency of 98 percent. At the end of the process, no hydrocarbons such as diesel; gasoline; benzene, toluene, ethyl benzene, and xylene (BTEX); or petroleum aromatic hydrocarbons (PAHs) were found. Iron washing achieved a removal efficiency of 70 percent, and for vanadium, the removal efficiency was 94.4 percent. The volume of soil treated was 41.6 m³ (38 m²), equivalent to 69.5 tons of soil. A rough calculation of the process costs estimated a total cost of $104.20/m³ ($114.00/m²). Our research indicates that there are a few studies demonstrating in situ flushing experiences under field conditions where both organic (TPH, diesel, gasoline, PAHs, BTEX) and metal (iron and vanadium) removals are reported. © 2004 Wiley Periodicals, Inc.     

Characteristics of gas and residues produced from electric arc pyrolysis of waste lubricating oil

An attempted has been made to recover high-calorific fuel gas and useful carbonaceous residue by the electric arc pyrolysis of waste lubricating oil. The characteristics of gas and residues produced from electric arc pyrolysis of waste lubricating oil were investigated in this study. The produced gas was mainly composed of hydrogen (35–40%), acetylene (13–20%), ethylene (3–4%) and other hydrocarbons, whereas the concentration of CO was very low. Calorific values of gas ranged from 11,000 to 13,000 kcal kg^?1 and the concentrations of toxic gases, such as NO_x, HCl and HF, were below the regulatory emissions limit. Gas chromatography–mass spectrometry (GC/MS) analysis of liquid-phase residues showed that high molecular-weight hydrocarbons in waste lubricating oil were pyrolyzed into low molecular-weight hydrocarbons and hydrogen. Dehydrogenation was found to be the main pyrolysis mechanism due to the high reaction temperature induced by electric arc. The average particle size of soot as carbonaceous residue was about 10 μm. The carbon content and heavy metals in soot were above 60% and below 0.01 ppm, respectively. The utilization of soot as industrial material resources such as carbon black seems to be feasible after refining and grinding.     

Evaluation of algal phytoremediation of light extractable petroleum hydrocarbons in subarctic climates

The presence of an organic mat in a hydrocarbon‐impacted creek in Whitehorse, Yukon Territory, Canada was examined for contributions to in situ remediation of petroleum‐contaminated water. This article investigates the role of algae, found in the organic mat, in the remediation of light extractable petroleum hydrocarbons (LEPHs) at the site and in the laboratory. During the study, LEPH concentrations were reduced by 16.8 percent in the presence of algae alone (algal solution) and 30.4 percent in the combined organic mat solution containing microbial consortia. The study results indicate that algal species at the site did not directly phytoremediate hydrocarbons. Rather, they were part of the total biological degradation taking place. © 2009 Wiley Periodicals, Inc.     

Degradation of petroleum hydrocarbons from bottom sludge of crude oil storage tanks using in-vessel composting followed by oxidation with hydrogen peroxide and Fenton

In this research the feasibility of aerated in-vessel composting process followed by chemical oxidation with H₂O₂ and Fenton for removal of petroleum hydrocarbons from oily sludge of crude oil storage tanks was investigated. The ratios of the sludge to immature compost were 1:0 (as abiotic control), 1:2, 1:4, 1:6, 1:8 and 1:10 (as dry basis) at a C:N:P ratio of 100:5:1 and 55 % moisture content for a period of 10 weeks. Six concentrations of H₂O₂ and Fenton were added to the compost mixture for a period of 24- and 48-h reaction times. Results showed that petroleum hydrocarbons removal in ratios of 1:2, 1:4, 1:6, 1:8 and 1:10 were 66.6, 73.2, 74.8, 80.2 and 79.9 %, respectively. The results of the abiotic experiments indicated that the main mechanism of hydrocarbon removal in the composting reactors was biological. The application of combined composting and chemical oxidation demonstrated a remarkable (about 88 %) overall removal. The study showed that in-vessel composting combined with chemical oxidation is a viable choice for the remediation of the sludge.     

Removal of Oil from the Sea Surface through Particulate Interactions: Review and Prospectus

The fate of oil spilled in coastal zones depends in large part on the interactions with environmental factors existing within a short time of the spill event. In addition to weathering which produces changes in the chemistry of the hydrocarbon stock, physical interactions between oil and suspended particulate matter (SPM), both organic and inorganic, play a role in determining the dispersal and sedimentation rates of the spill. This in turn affects the degradation rate of the oil. This paper provides a comprehensive literature review of the role of oil–particle interactions in removal of petroleum hydrocarbons from the sea surface and provides estimates of the degree to which SPM may augment the deposition of oil. Both field and laboratory observations have shown widely varying rates of oil removal due to particulate interactions. The discussion covers the interaction between oil weathering, injection, sinking, adsorption, microbial processes, flocculation and ingestion by zooplankton, which all contribute to packaging oil and SPM into settling aggregates.     

Hydrogen peroxide for physicochemically degrading petroleum-contaminated soils

Catalyzed hydrogen peroxide was applied to contaminated soil at an equipment storage yard in Reno, Nevada, that had also been used as a dump for motor oil and diesel fuel for twenty years. The site is only a quarter mile from the Truckee River—a principal source of Reno's drinking water. This article details hydrogen peroxide's advantages, disadvantages, costs, and treatment for reducing to below the 100 mg/kg Nevada action level the petroleum hydrocarbons in the yard's arid soil, which is characterized by low organic carbon content and low manganese oxide content.