Composting Of <100 mm Fraction Of Municipal Solid Waste

A low cost solution for management of municipal solid waste in small municipalities was investigated; composting experiments were done using domestic waste. Particles >100 mm were removed, the screened substrate (<100 mm) was used for composting experiments on static piles. The results have shown that the size of waste does not affect composting. Though the inert material left greatly adds to the porosity, rainfall does not markedly affect the process; in fact excessive dryness gave the least stable end product, and total nitrogen, ammoniacal nitrogen and phosphorus content were the best pointers to the instability.     

Solid Waste Recycling And Reuse In Bangkok

Materials recovered from solid waste in Bangkok are mainly glass bottles, paper and paper products, plastic products and metals. Materials are separated at three different stages of the collection process: at the source, prior to collection; by the crews of the collection vehicle; and by the scavengers at the dump site. The total daily tonnage of recyclable garbage collected at the source by the waste pickers is estimated at 286 tonnes, about 5% of the garbage collected by the city. There are small scale recycling shops (SSR) located around the main disposal sites where collected materials are sold by the collection crews and the scavengers. The quantity of materials delivered to the SSR shops by the collection crew vary between 1-6 tonnes per day. The amount of materials recovered by the scavengers (at the dump site) varies between 50-150 kg person^-1 day^-1. Therefore around 7.5% of the solid waste is recycled. In Bangkok both formal and informal sectors manufacture paper pulp, cardboard boxes and magazines from the recyclable paper. Paper products which account for 55% of the total waste stream are considered as the largest "product group" in the municipal solid waste. Recyclable glass (1-3% of the total waste stream) or cullet is used to manufacture plain glasses or cups. Plastics constitute about 10-15% of the waste stream. The benefit/cost ratios of production of most of these industries were reported to be higher than 1.5. In order to enhance recycling, legislative measures need to be introduced and enforced. In Thailand, there is, however, no law concerning recycling. There is no incentive for the consumer to separate solid waste for recycling, as the prices of waste in Bangkok are low and inconsistent. Therefore the pricing system should be more organized for recycling to be more effective.     

The Origins Of Municipal Solid Waste: II. Policy Options For Plastics Waste Management

Plastic items in some portions of municipal solid waste (MSW), particularly from households and restaurants, have long been viewed as a disposal problem and a symbol of a "throwaway society". There is no question that the amount of plastics in solid waste is growing. However, this observation alone should not cause an hysteria of public policies for the separate management of the plastics or any other portion of the waste. The amount of plastics, and the contribution of the items discarded, must be viewed holistically in setting a solid waste management policy. This paper questions the basis for some U.S. plastics waste policy proposals by reviewing recent U.S. data on the effect of plastics on waste reduction, and the fate of discarded plastics products. Some alternative future policy directions are also discussed.     

Policy Barriers To 50% Diversion Of Municipal Solid Waste

A number of policy barriers must be addressed by the governments in Europe and North America which have adopted objectives of diverting from disposal something like 50% of the solid waste stream by means of reduction, re-use and recycling. These include: the need for clarification of responsibilities of all levels of government and of private sector product manufacturers and waste disposers; putting in place incentives for source separation; ensuring markets for recyclables; and allocating the increased cost of waste management. This paper reports on findings of a research project undertaken in 1991-92 on steps being taken by different jurisdictions to overcome such barriers.     

Fate Of An Absorbent Gelling Material For Hygiene Paper Products In Landfill And Composting

A cross-linked polyacrylate polymer, referred to as absorbent gelling material (AGM), has been developed for use in hygiene paper products, such as infant diapers (nappies). The fate and effects of this polymer were studied in laboratory models of landfill and aerobic composting. Radiolabelled (¹⁴C) AGM was used to facilitate determination of fate and mass balance. Tests were conducted in 1201 reactors containing a mixture of solid waste and compost or solid waste only, and panty diaper pads. Controlled temperature and leachate recycle were used to accelerate the biological processes. AGM caused no adverse effects and most of the material remained associated with the diaper pad and surrounding waste. Very little AGM (less than 1%) biodegraded to CO₂/CH₄ under landfill conditions, while 2-4% appeared in leachate. The leachate was highly biodegradable aerobically. More of the AGM (6.4%) biodegraded to CO₂/CH₄ under aerobic composting conditions, while less than 1% appeared in leachate.     

Mechanical properties of Municipal Solid Waste by SDMT

In the paper the results of a geotechnical investigation carried on Municipal Solid Waste (MSW) materials retrieved from the “Cozzo Vuturo” landfill in the Enna area (Sicily, Italy) are reported and analyzed. Mechanical properties were determined both by in situ and laboratory large-scale one dimensional compression tests.While among in situ tests, Dilatomer Marchetti Tests (DMT) is used widely in measuring soil properties, the adoption of the DMT for the measurements of MSW properties has not often been documented in literature. To validate its applicability for the estimation of MSW properties, a comparison between the seismic dilatometer (SDMT) results and the waste properties evaluated by laboratory tests was carried out.Parameters for “fresh” and “degraded waste” have been evaluated. These preliminary results seems to be promising as concerns the assessment of the friction angle of waste and the evaluation of the S-wave in terms of shear wave velocity. Further studies are certainly required to obtain more representative values of the elastic parameters according to the SDMT measurements.     

Use Of Mixed Probability Distributions For The Analysis Of Solid Waste Generation Data

The issues associated with the statistical analysis of municipal solid waste generation patterns are addressed in this paper. A methodology for determining a mixed probability distribution for daily waste generation data is developed. This methodology is then applied to data from two Canadian municipalities.     

Precious Metals in Municipal Solid Waste Incineration Bottom Ash

Municipal solid waste incineration (MSWI) bottom ash contains economically significant levels of silver and gold. Bottom ashes from incinerators at Amsterdam and Ludwigshafen were sampled, processed, and analyzed to determine the composition, size, and mass distribution of the precious metals. In order to establish accurate statistics of the gold particles, a sample of heavy non-ferrous metals produced from 15 tons of wet processed Amsterdam ash was analyzed by a new technology called magnetic density separation (MDS). Amsterdam’s bottom ash contains approximately 10 ppm of silver and 0.4 ppm of gold, which was found in particulate form in all size fractions below 20 mm. The sample from Ludwigshafen was too small to give accurate values on the gold content, but the silver content was found to be identical to the value measured for the Amsterdam ash. Precious metal value in particles smaller than 2 mm seems to derive mainly from waste of electrical and electronic equipment (WEEE), whereas larger precious metal particles are from jewelry and constitute the major part of the economic value. Economical analysis shows that separation of precious metals from the ash may be viable with the presently high prices of non-ferrous metals. In order to recover the precious metals, bottom ash must first be classified into different size fractions. Then, the heavy non-ferrous (HNF) metals should be concentrated by physical separation (eddy current separation, density separation, etc.). Finally, MDS can separate gold from the other HNF metals (copper, zinc). Gold-enriched concentrates can be sold to the precious metal smelter and the copper-zinc fraction to a brass or copper smelter.     

Combined Municipal Solid Waste and biomass system optimization for district energy applications

Municipal Solid Waste (MSW) disposal has been a controversial issue in many countries over the past years, due to disagreement among the various stakeholders on the waste management policies and technologies to be adopted. One of the ways of treating/disposing MSW is energy recovery, as waste is considered to contain a considerable amount of bio-waste and therefore can lead to renewable energy production. The overall efficiency can be very high in the cases of co-generation or tri-generation. In this paper a model is presented, aiming to support decision makers in issues relating to Municipal Solid Waste energy recovery. The idea of using more fuel sources, including MSW and agricultural residue biomass that may exist in a rural area, is explored. The model aims at optimizing the system specifications, such as the capacity of the base-load Waste-to-Energy facility, the capacity of the peak-load biomass boiler and the location of the facility. Furthermore, it defines the quantity of each potential fuel source that should be used annually, in order to maximize the financial yield of the investment. The results of an energy tri-generation case study application at a rural area of Greece, using mixed MSW and biomass, indicate positive financial yield of investment. In addition, a sensitivity analysis is performed on the effect of the most important parameters of the model on the optimum solution, pinpointing the parameters of interest rate, investment cost and heating oil price, as those requiring the attention of the decision makers. Finally, the sensitivity analysis is enhanced by a stochastic analysis to determine the effect of the volatility of parameters on the robustness of the model and the solution obtained.     

A historical perspective of Global Warming Potential from Municipal Solid Waste Management

The Municipal Solid Waste Management (MSWM) sector has developed considerably during the past century, paving the way for maximum resource (materials and energy) recovery and minimising environmental impacts such as global warming associated with it. The current study is assessing the historical development of MSWM in the municipality of Aalborg, Denmark throughout the period of 1970 to 2010, and its implications regarding Global Warming Potential (GWP₁₀₀), using the Life Cycle Assessment (LCA) approach. Historical data regarding MSW composition, and different treatment technologies such as incineration, recycling and composting has been used in order to perform the analysis. The LCA results show a continuous improvement in environmental performance of MSWM from 1970 to 2010 mainly due to the changes in treatment options, improved efficiency of various treatment technologies and increasing focus on recycling, resulting in a shift from net emission of 618 kg CO₂-eq. tonne^?1 to net saving of 670 kg CO₂-eq. tonne^?1 of MSWM.     

Geotechnical characterization of a Municipal Solid Waste Incineration Ash from a Michigan monofill

A field and laboratory geotechnical characterization study of a Municipal Solid Waste Incineration Ash disposed of at the Carleton Farms monofill in Michigan was performed. Field characterization consisted of field observations, collection of four bulk samples and performance of shear wave velocity measurements at two locations. Laboratory characterization consisted of basic geotechnical characterization, i.e., grain size distribution, Atterberg limits, specific gravity tests, compaction tests as well as moisture and organic content assessment followed by direct shear and triaxial shear testing. The test results of this investigation are compared to results in the literature. The grain size distribution of the samples was found to be very similar and consistent with the grain size distribution data available in the literature, but the compaction characteristics were found to vary significantly. Specific gravities were also lower than specific gravities of silicic soils. Shear strengths were higher than typically reported for sandy soils, even for MSWI ash specimens at a loose state. Strain rate was not found to impact the shear resistance. Significant differences in triaxial shear were observed between a dry and a saturated specimen not only in terms of peak shear resistance, but also in terms of stress–strain response. In situ shear wave velocities ranged from 500 to 800 m/s at a depth of about 8 m, to 1100–1200 m/s at a depth of 50 m. These high shear wave velocities are consistent with field observations indicating the formation of cemented blocks of ash with time, but this “ageing” process in MSWI ash is still not well understood and additional research is needed. An improved understanding of the long-term behavior of MSWI ash, including the effects of moisture and ash chemical composition on the ageing process, as well as the leaching characteristics of the material, may promote unbound utilization of the ash in civil infrastructure.     

Short-term/Long-term Solutions In Waste Management: Economics And The Transition Process

Cleaner technology and recycling, as the preferred solution to waste management, is increasing in implementation but not at the rate expected given the successes and paybacks associated with those strategies. The reasons for the delay in implementation lie in the conflict between short-term and long-term solutions. The factors that contribute to hindrance or facilitation of the transition are found in: a) the distinction between the short-term and the long-term at a technical level; b) the distinction between the short-term and the long-term at a political level; c) the investment decision at the firm level; and d) related investments in infrastructure, organization, and institutions. This article identifies which constraints will disappear with time, which constraints are institutional and will require deliberate modification, and which constraints are permanent and must be considered part of the costs of the long-term solution. The goal is not to argue against short-term solutions, but for the need to acknowledge unavoidable costs associated with the transition from the short-term to the long-term solution.     

A Comparative Overview Of Recycling In London And Hamburg

The level of recycling for household waste is significantly higher in Hamburg than in London, yet the extent of materials recovery in both cities is well below technically achievable levels. This paper shows that the higher level of recycling in Hamburg can be accounted for by three main factors: a higher density of recycling facilities combined with the use of more sophisticated collection systems such as a dual-bin service for putrescible wastes; a unified administrative structure for waste management under direct control of an elected regional government; and finally, a system of proportional representation in local government allowing environmentalist political demands to be directly translated into public policy. Despite these differences however, both cities face difficulties with the expansion of recycling derived from the weakness of the secondary materials market, the lack of legislative control over the size and composition of the waste stream, the fiscal constraints on local government and the expense of comprehensive recycling programmes in comparison with alternative forms of waste disposal. This paper concludes that the high cost of recycling presents a fundamental political dilemma for sustainable waste management policy in developed economies.     

Kinetic Study Of The Composting Of Evergreen Oak Forestry Waste

The successive stages in the composting process of forestry waste from evergreen oak (Quercus ilx sbsp. ballota) were studied under controlled conditions (initial) carbon to nitrogen ratio = 30, T = 27°C). The original material was composted for 6 months and sampled every 15 days. The variables measured on the oak biomass in the course of the experiment showed different kinetics: the weight loss and germination index underwent a monotonic increase whereas the reducing sugars, phenols and E₄₆₅/E₆₆₅ extinction ratio of the water-soluble fraction stabilized at their lowest values after the first 2 weeks. Other variables, such as alkali solubility, water repellency, pH and particle size, showed maximum or minimum values at intermediate stages of the experiment. In contrast to the adverse agrobiological effects of the direct application to soil of the original waste, germination biotests and greenhouse experiments showed that plant response improved from the 2 first weeks of composting. The kinetics observed for the parameters studied suggested that the less favourable effect on plant yield may come from phytotoxic substances in compost but also from the microbial use of soil N required for the transformation of the most biodegradable compost fractions in special hemicelluloses.     

Potential To Use Waste Tires As Supplemental Fuel In Pulp And Paper Mill Boilers,Cement Kilns And In Road Pavement

The objective of this paper is to evaluate the recycling potential of waste tires as an energy source and for use in road pavement. North Carolina, U.S.A., is used as a case study. Scrap tires may be burned for supplemental fuel in pulp and paper mill boilers and cement kilns. Five pulp and paper mill boilers in North Carolina could consume over 90% of the 6 million tires generated annually in the state. Cement kilns located within 400 km of North Carolina population centers could consume about 6.6 million tires annually. Based on the quantity of pavement laid in North Carolina, nonproprietary and proprietary versions of asphalt rubber concrete have the potential to consume 1.8 and 7.2 million tires, respectively. Rubber modified asphalt concrete has the potential to consume up to 16.5 million tires. However, technological and economic limitations suggest that large scale implementation is unlikely for the short term. Environmental considerations pertaining to each alternative are discussed. Estimates of this nature are critical as planning regions formulate solid waste management plans which include recycling.     

Use Of Peat Extract In The Ensiling Of Fisheries Wastes

Fish processing wastes, namely minced cod (Gadus morhua) offal and minced male capelin (Mallotus villosus), were used in two kinds of ensiling (silage making) processes. In one process they were ensiled by the direct addition of acids, and in the other they were ensiled using various carbohydrate sources and bacterial cultures to produce organic acids in situ. Ensiled material was analysed for various components at times throughout its storage period, and monitored for onset of spoilage. It was found that neither prior freezing nor initial heat treatment of capelin had an effect on the preservation effectiveness of the ensiling process. It was concluded that both the addition of formic acid to cod offal and the fermentation of lactic acid bacteria are effective methods of ensiling this material. Peat extracts with a relatively high carbohydrate content were found to be a satisfactory source of carbohydrates for the fermentation of lactic acid bacteria in cod offal silage. However, peat extracts with a relatively low pH were found to be unsatisfactory as a direct source of acid for ensiling.     

Environmental impacts of residual Municipal Solid Waste incineration: A comparison of 110 French incinerators using a life cycle approach

Incineration is the main option for residual Municipal Solid Waste treatment in France. This study compares the environmental performances of 110 French incinerators (i.e. 85% of the total number of plants currently in activity in France) in a Life Cycle Assessment perspective, considering 5 non-toxic impact categories: climate change, photochemical oxidant formation, particulate matter formation, terrestrial acidification and marine eutrophication. Mean, median and lower/upper impact potentials are determined considering the incineration of 1 tonne of French residual Municipal Solid Waste. The results highlight the relatively large variability of the impact potentials as a function of the plant technical performances. In particular, the climate change impact potential of the incineration of 1 tonne of waste ranges from a benefit of ?58 kg CO₂-eq to a relatively large burden of 408 kg CO₂-eq, with 294 kg CO₂-eq as the average impact. Two main plant-specific parameters drive the impact potentials regarding the 5 non-toxic impact categories under study: the energy recovery and delivery rate and the NO_x process-specific emissions. The variability of the impact potentials as a function of incinerator characteristics therefore calls for the use of site-specific data when required by the LCA goal and scope definition phase, in particular when the study focuses on a specific incinerator or on a local waste management plan, and when these data are available.     

Trends In Regulatory Acceptance Of Risk-Based Cleanup Goals And Natural Attenuation For Site Closure

Since 1994, there has been a significant regulatory shift toward risk-based cleanup standards based on the site-specific risk of the more toxic and mobile compounds; namely, benzene, ethyl benzene, toluene, and xylene (BTEX). This regulatory shift has been accompanied by a growing acceptance of natural attenuation as an important component of petroleum site remediation. This article briefly reviews regulatory progress toward risk-based remediation and describes the successful application of risk-based corrective actions (RBCAs) at two fuel contaminated sites on Air Force installations. By developing site-specific cleanup goals, and combining natural attenuation, source reduction, and land use controls, innovative risk-based closure plans have been implemented on these sites.     

Practical Simulation Of Composting In The Laboratory

A closed incubation system was developed for laboratory simulation of composting conditions at the interior of a large compost pile. A conductive heat flux control system (CHFC) was used to adjust the temperature of the internal wall to that of the compost center and compensate for heat loss. Insulated small vessels (400 cm³) controlled by the CHFC system were compared with similar vessels maintained at 30°C (mesophilic) and 55°C (thermophilic), and with large vessels (10 000 cm³) with and without the CHFC. Compost temperature rose rapidly to a maximum within 2-4 days, then gradually decreased. In mesophilic treatments (no CHFC), temperature at the matrix center increased to a maximum of 36°C in the small vessel and 50°C in the large vessel, while temperature in both vessels reached 50°C with the CHFC. Microbial activity was maintained by allowing compost to self-heat and controlling temperature externally with the CHFC. Higher temperatures were sustained for longer periods in CHFC vessels than in vessels without the CHFC. Periodic mixing of the compost matrix increased temperature and CO₂ evolution. Small vessels were successfully used in laboratory simulation of field-scale composting of a soil/organic matrix containing TNT and RDX munitions. The small vessel system reduced subsample error in compost monitoring from that of the large vessels. The CHFC has particular utility in research requiring expensive chemicals or hazardous substances.