铝箔复合膜集气袋对有机废气的适用性研究

通过在不同的时间段,测定存放于铝箔复合膜集气袋和玻璃注射器的丙酮,醋酸乙酯,苯,异丙醇标准气的浓度,气体浓度与贮存时间的关系,本次试验结果表明,丙酮,醋酸乙酯,苯,异丙醇在铝箔气袋中的稳定性明显优于在玻璃注射器中,应尽可能在８－２４ｈ内测定。     

利用活性炭纤维有机废气吸附回收装置治理二氯甲烷废气

文章介绍了一种化工生产过程中排出的二氯甲烷废气的治理装置———活性炭纤维有机废气吸附回收装置和治理工艺。由于采用了优越的吸附材料和先进的工艺设计 ,使吸附回收率达 97%以上 ,收到了很好的环境效益和经济效益     

湿法烟气脱硫工艺中烟气再热方式的选择

分析了湿法烟气脱硫烟气再热原因,介绍了多种烟气再热方法,并对其进行了技术分析,为湿法烟气脱硫工程的烟气再热系统设计提供了依据。     

Feasibility of landfill gas as a liquefied natural gas fuel source for refuse trucks

The purpose of this paper is to develop a methodology to evaluate the feasibility of using landfill gas (LFG) as a liquefied natural gas (LNG) fuel source for heavy-duty refuse trucks operating on landfills. Using LFG as a vehicle fuel can make the landfills more self-sustaining, reduce their dependence on fossil fuels, and reduce emissions and greenhouse gases. Acrion Technologies Inc. in association with Mack Trucks Inc. developed a technology to generate LNG from LFG using the CO2 WASH process. A successful application of this process was performed at the Eco Complex in Burlington County, PA. During this application two LNG refuse trucks were operated for 600 hr each using LNG produced from gases from the landfill. The methodology developed in this paper can evaluate the feasibility of three LFG options: doing nothing, electricity generation, and producing LNG to fuel refuse trucks. The methodology involved the modeling of several components: LFG generation, energy recovery processes, fleet operations, economic feasibility, and decision-making. The economic feasibility considers factors such as capital, maintenance, operational, and fuel costs, emissions and tax benefits, and the sale of products such as surplus LNG and food-grade carbon dioxide (CO2). Texas was used as a case study. The 96 landfills in Texas were prioritized and 17 landfills were identified that showed potential for converting LFG to LNG for use as a refuse truck fuel. The methodology was applied to a pilot landfill in El Paso, TX. The analysis showed that converting LFG to LNG to fuel refuse trucks proved to be the most feasible option and that the methodology can be applied for any landfill that considers this option.     

Greenhouse gas induced climate change

Simulations using global coupled climate models predict a climate change due to the increasing concentration of greenhouse gases and aerosols in the atmosphere. Both are associated with the burning of fossil fuels. There has been considerable debate if this postulated human influence is already evident. This paper gives an overview on some recent material on this question. One particular study using optimal fingerprints (Hegerl et al., 1996) is explained in more detail. In this study, an optimal fingerprint analysis is applied to temperature trend patterns over several decades. The results show the probability being less than 5% that the most recently observed 30 year trend is due to naturally occurring climate fluctuations. This result suggests that the present warming is caused by some external influence on climate, e.g. by the increasing concentrations of greenhouse gases and aerosols. More work is needed to address the uncertainties in the magnitude of naturally occurring climate fluctuations. Also, other external influences on climate need to be investigated to uniquely attribute the present climate change to the human influence.     

Structural and sensing properties of ethanol gas using Pd-doped SnO2 thick film gas sensor

Environmental Science and Pollution Research - In the present study, we fabricate undoped and 1 wt% palladium (Pd)-doped tin oxide (SnO2) films were deposited on alumina substrate using...     

填埋场沼气发电的温室气体减排效益分析

填埋场沼气是垃圾卫生填埋场产生的可利用资源.以深圳下坪垃圾填埋场为例,定量分析垃圾填埋气体发电的温室气体减排效益.结果表明,填埋场沼气发电具有很好的经济效益和环境效益,可作为与发达国家进行CDM(清洁发展机制)项目合作的优先技术领域.     

Understanding oil and gas pneumatic controllers in the Denver–Julesburg basin using optical gas imaging

ABSTRACT

In the spring of 2018, a 10-day field study was conducted in Colorado’s Denver-Julesburg oil and natural gas production basin to improve information on well pad pneumatic controller (PC) populations and identify PCs with potential maintenance issues (MIs) causing excess emissions through a novel optical gas imaging (OGI) survey approach. A total of 500 natural gas-emitting PCs servicing 102 wells (4.9 PCs/well) were surveyed at 31 facilities operated by seven different companies. The PCs were characterized by their designed operational function and applications, with 83% of the PC population identified as intermittent PCs (IPCs). An OGI inspection protocol was used to investigate emissions on 447 working PCs from this set. OGI detected continuous emissions from 11.3% of observed IPCs and these were classified as experiencing some level of MIs. OGI imaging modes were observed to have a significant effect on emission detectability with high sensitivity mode detection rates being approximately 2 times higher compared to auto mode. Fourteen snapshot emission measurements (not including actuations) were conducted on IPCs in this category using a high-volume sampling device with augmented quality assurance procedures with observed emissions rates ranging from 0.1 up to 31.3 scf/hr (mean = 2.8 scf/hr). For PCs with continuous depressurization type (CPC), 36.8% had continuous emissions observed by OGI. Four supporting emission measurements were conducted on CPCs with one unit exceeding the low bleed regulatory emission threshold with an emission rate of 9.9 scf/hr (mean = 4.2 scf/hr). Additional information was collected on PC actuation events, as observed with OGI, which showed a strong correlation between observed actuation events and facility production compared to observed continuous emissions caused by MIs which did not correlate with facility production.

Implications: A novel survey approach of pneumatic controllers at oil and natural gas production facilities in the Denver-Julesburg basin, using optical gas imaging and supporting emission measurements, was demonstrated as an effective method to identify controllers with potential maintenance issues causing excess emissions. The results of the pneumatic controller and optical gas imaging surveys improved information on pneumatic controller populations within the basin and also demonstrated the significant effect optical gas imaging modes have on emission detections.     

基于Aspen Plus软件的生物质气与煤混合燃烧烟气排放特性计算分析

为了分析生物质气与煤混合燃烧对烟气排放特性的影响,基于Aspen Plus软件,搭建了生物质气与煤混合燃烧模型,对混合燃烧产物进行模拟计算。在生物质气化过程中,随着空燃比的增加,生物质气的低位热值先升高后降低。选取低位热值最高时的生物质气和煤在不同生物质掺烧比例下混合燃烧。随着生物质掺烧比例从0%增加到30%,在保证混合燃烧的理论空气量条件下,炉膛燃烧温度逐渐下降,烟气排放特性也随之变化。在掺烧比例达到30%时,SO_2的体积分数降低了30%左右,H_2O的体积分数增加了26.7%~39.2%,烟气排放量增加了2.38%~3.2%。随着生物质掺烧比例的增加,混合燃烧对锅炉运行造成的影响逐渐增大。     

循环流化床烟气脱硫塔入口结构改进的数值模拟

采用商用Fluent软件提供的k-ε湍流模型对循环流化床脱硫塔内部流场进行了数值模拟,重点考察入口结构对脱硫塔内气相速度分布均匀性的影响,并用速度不均匀度定量描述了流场的均匀性。结果表明,当前使用90°弯管进气结构的脱硫塔内部流场存在明显的不均匀性,主要是入口处气流90°转向造成的。为此采用组合弯管进气结构代替90°弯管进气结构,以改善脱硫塔内流场不均匀性。入口结构改为组合弯管进气结构后,脱硫塔内流场不均匀性得到很大改善,速度分布的不均匀度明显减小,因此组合弯管进气结构有利于烟气与脱硫剂的充分混合反应,提高脱硫效率。     

火化过程中二噁英类污染物减排技术研究

为减少火化过程中二噁英类污染物的排放,研究了"热交换器 布袋除尘器 活性炭纤维毡"三级组合对火化遗体烟气中二噁英类污染物的去除效果.利用急冷技术将二次燃烧室排出的火化烟气温度降到90～130℃.实验表明,布袋除尘器去除火化烟气中二噁英类污染物的效率为57.4%;布袋除尘器分别与厚度为5、15 mm的活性炭纤维毡组合去除火化烟气中二噁英类污染物的效率分别为64.0%和89.2%.     

Compositions and greenhouse gas emission factors of flared and vented gas in the Western Canadian Sedimentary Basin

A significant obstacle in evaluating mitigation strategies for flaring and venting in the upstream oil and gas industry is the lack of publicly available data on the chemical composition of the gas. This information is required to determine the economic value of the gas, infrastructure and processing requirements, and potential emissions or emissions credits, all of which have significant impact on the economics of such strategies. This paper describes a method for estimating the composition of solution gas being flared and vented at individual facilities, and presents results derived for Alberta, Canada, which sits at the heart of the Western Canadian Sedimentary Basin. Using large amounts of raw data obtained through the Alberta Energy Resources Conservation Board, a relational database was created and specialized queries were developed to link production stream data, raw gas samples, and geography to create production-linked gas composition profiles for approximately half of the currently active facilities. These were used to create composition maps for the entire region, to which the remaining facilities with unknown compositions were geographically linked. The derived data were used to compute a range of solution gas composition profiles and greenhouse gas emission factors, providing new insight into flaring and venting in the region and enabling informed analysis of future management and mitigation strategies.

Implications: Accurate and transparent determination of environmental impacts of flaring and venting of gas associated with oil production, and potential benefits of mitigation, is severely hampered by the lack of publicly available gas composition data. In jurisdictions within the Western Canadian Sedimentary Basin, frameworks exist for regulating and trading carbon offset credits but current potential for mitigation is limited by a lack of standardized methods for calculating CO₂ equivalent emissions. The composition and emission factor data derived in this paper will be useful to industry, regulators, policy researchers, and entrepreneurs seeking statistically significant and openly available data necessary to manage and mitigate upstream flaring and venting activity and estimate greenhouse gas impacts.     

利用无泵水幕废气净化器治理高浓度NOx的工程实践

介绍了无泵水幕废气净化器的工作原理和运行特点,采用该设备处理某金刚石公司的酸洗车间高浓度的NOx气体,其净化效率达90%以上,净化后的NOx气体可直接达标排放.无泵水幕废气净化器解决了传统的水喷淋塔普遍存在的喷嘴堵塞、单级净化效率低、运行费用高等问题,在高浓度酸性气体治理方面具有很好的推广应用前景.     

电除尘器进口矩形烟道气流分布改进的CFD模拟

应用CFD软件对某电厂电除尘器进口矩形烟道内气流分布进行数值模拟.结果表明:电除尘器原进口矩形烟道监测截面的气流分布极其不均匀,数值模拟结果与实验结果速度分布趋势比较吻合.基于此,通过多次改变电除尘器进口矩形烟道内导流板的数量、位置、尺寸等结构参数,使得改造后烟道监测截面风量偏差降到了±2.2%,气流分布相对均方根值均...     

双循环垂直筛板喷射鼓泡脱硫塔的吸收性能

设计了一种中试规模的双循环垂直筛板喷射鼓泡脱硫塔,该塔由直径分别为600 mm和150 mm的两套垂直筛板结构组成双循环。一级循环采用了一块下端开有栅孔的大直径垂直筛板,二级循环则采用了上端开有栅孔的小直径垂直筛板。两级垂直筛板上的布气栅孔均可埋入吸收液下,使塔内的气液混合处于喷射鼓泡吸收状态。研究了小直径垂直筛板埋入深度分别对单独采用二级循环和采用双循环时装置脱硫效率的影响。单独采用二级循环,在保持脱硫液pH值和烟气SO2浓度一致的情况下,小直径垂直筛板的液位高度为220 mm时(喷射鼓泡操作方式)比液位高度为80 mm时(即典型小直径垂直筛板操作方式)的脱硫效率高40%左右。采用双循环操作模式时,小直径垂直筛板液位高度为220 mm时(喷射鼓泡操作方式)比液位高度为80 mm时(即典型小垂直筛板操作方式)的总脱硫效率高30%左右。     

Electricity generation from landfill gas in Turkey

Landfill gas (LFG)-to-energy plants in Turkey were investigated, and the LFG-to-energy plant of a metropolitan municipal landfill was monitored for 3 years. Installed capacities and actual gas engine working hours were determined. An equation was developed to estimate the power capacity for LFG-to-energy plants for a given amount of landfilled waste. Monitoring the actual gas generation rates enabled determination of LFG generation factors for Turkish municipal waste. A significant relationship (R = 0.524, p < 0.01, two-tailed) was found between the amounts of landfilled waste and the ambient temperature, which can be attributed to food consumption and kitchen waste generation behaviors influenced by the ambient temperature. However, no significant correlation was found between the ambient temperature and the generated LFG. A temperature buffering capacity was inferred to exist within the landfill, which enables the anaerobic reactions to continue functioning even during cold seasons. The average LFG and energy generation rates were 45 m³ LFG/ton waste landfilled and 0.08 MWhr/ton waste landfilled, respectively. The mean specific LFG consumption for electricity generation was 529 ± 28 m³/MWhr.

Implications: The paper will be useful for local authorities who need to manage municipal waste by using landfills. The paper will also be useful for investors who want to evaluate the energy production potential of municipal wastes and the factors affecting the energy generation process mostly for economical purposes. Landfills can be regarded as energy sources and their potentials need to be investigated. The paper will also be useful for policymakers dealing with energy issues. The paper contains information on real practical data such as engine working hours, equation to estimate the necessary power for a given amount of landfilled waste, and son on.