Geomechanical analysis of the Naylor Field,Otway Basin,Australia: Implications for CO2 injection and storage

A geomechanical assessment of the Naylor Field, Otway Basin, Australia has been undertaken to investigate the possible geomechanical effects of CO₂ injection and storage. The study aims to evaluate the geomechanical behaviour of the caprock/reservoir system and to estimate the risk of fault reactivation. The stress regime in the onshore Victorian Otway Basin is inferred to be strike–slip if the maximum horizontal stress is calculated using frictional limits and DITF (drilling induced tensile fracture) occurrence, or normal if maximum horizontal stress is based on analysis of dipole sonic log data. The NW–SE maximum horizontal stress orientation (142°N) determined from a resistivity image log is broadly consistent with previous estimates and confirms a NW–SE maximum horizontal stress orientation for the Otway Basin.An analytical geomechanical solution is used to describe stress changes in the subsurface of the Naylor Field. The computed reservoir stress path for the Naylor Field is then incorporated into fault reactivation analysis to estimate the minimum pore pressure increase required to cause fault reactivation (ΔP_p).The highest reactivation propensity (for critically-oriented faults) ranges from an estimated pore pressure increase (ΔP_p) of 1 MPa to 15.7 MPa (estimated pore pressure of 18.5–33.2 MPa) depending on assumptions made about maximum horizontal stress magnitude, fault strength, reservoir stress path and Biot's coefficient. The critical pore pressure changes for known faults at Naylor Field range from an estimated pore pressure increase (ΔP_p) of 2 MPa to 17 MPa (estimated pore pressure of 19.5–34.5 MPa).     

Petrophysical analysis to investigate the effects of carbon dioxide storage in a subsurface saline aquifer at Ketzin, Germany (CO2SINK)

To test the injection behaviour of CO₂ into brine-saturated rock and to evaluate the dependence of geophysical properties on CO₂ injection, flow and exposure experiments with brine and CO₂ were performed on sandstone samples of the Stuttgart Formation representing potential reservoir rocks for CO₂ storage. The sandstone samples studied are generally fine-grained with porosities between 17 and 32% and permeabilities between 1 and 100 mD.Additional batch experiments were performed to predict the long-term behaviour of geological CO₂ storage. Reservoir rock samples were exposed over a period of several months to CO₂-saturated reservoir fluid in high-pressure vessels under in situ temperature and pressure conditions. Petrophysical parameters, porosity and the pore radius distribution were investigated before and after the experiments by NMR (Nuclear Magnetic Resonance) relaxation and mercury injection. Most of the NMR measurements of the tested samples showed a slight increase of porosity and a higher proportion of large pores.     

Assessment of basin-scale hydrologic impacts of CO2 sequestration,Illinois basin

Idealized, basin-scale sharp-interface models of CO₂ injection were constructed for the Illinois basin. Porosity and permeability were decreased with depth within the Mount Simon Formation. Eau Claire confining unit porosity and permeability were kept fixed. We used 726 injection wells located near 42 power plants to deliver 80 million metric tons of CO₂/year. After 100 years of continuous injection, deviatoric fluid pressures varied between 5.6 and 18 MPa across central and southern part of the Illinois basin. Maximum deviatoric pressure reached about 50% of lithostatic levels to the south. The pressure disturbance (>0.03 MPa) propagated 10–25 km away from the injection wells resulting in significant well–well pressure interference. These findings are consistent with single-phase analytical solutions of injection. The radial footprint of the CO₂ plume at each well was only 0.5–2 km after 100 years of injection. Net lateral brine displacement was insignificant due to increasing radial distance from injection well and leakage across the Eau Claire confining unit. On geologic time scales CO₂ would migrate northward at a rate of about 6 m/1000 years. Because of paleo-seismic events in this region (M5.5–M7.5), care should be taken to avoid high pore pressures in the southern Illinois basin.     

Biofilm enhanced geologic sequestration of supercritical CO2

In order to develop subsurface CO₂ storage as a viable engineered mechanism to reduce the emission of CO₂ into the atmosphere, any potential leakage of injected supercritical CO₂ (SC-CO₂) from the deep subsurface to the atmosphere must be reduced. Here, we investigate the utility of biofilms, which are microorganism assemblages firmly attached to a surface, as a means of reducing the permeability of deep subsurface porous geological matrices under high pressure and in the presence of SC-CO₂, using a unique high pressure (8.9 MPa), moderate temperature (32 °C) flow reactor containing 40 millidarcy Berea sandstone cores. The flow reactor containing the sandstone core was inoculated with the biofilm forming organism Shewanella fridgidimarina. Electron microscopy of the rock core revealed substantial biofilm growth and accumulation under high-pressure conditions in the rock pore space which caused >95% reduction in core permeability. Permeability increased only slightly in response to SC-CO₂ challenges of up to 71 h and starvation for up to 363 h in length. Viable population assays of microorganisms in the effluent indicated survival of the cells following SC-CO₂ challenges and starvation, although S. fridgidimarina was succeeded by Bacillus mojavensis and Citrobacter sp. which were native in the core. These observations suggest that engineered biofilm barriers may be used to enhance the geologic sequestration of atmospheric CO₂.     

Water/acid gas interfacial tensions and their impact on acid gas geological storage

Acid gas geological disposal is a promising process to reduce CO₂ atmospheric emissions and an environment-friendly and economic alternative to the transformation of H₂S into sulphur by the Claus process. Acid gas confinement in geological formations is to a large extent controlled by the capillary properties of the water/acid–gas/caprock system, because a significant fraction of the injected gas rises buoyantly and accumulates beneath the caprock. These properties include the water/acid gas interfacial tension (IFT), to which the so-called capillary entry pressure of the gas in the water-saturated caprock is proportional. In this paper we present the first ever systematic water/acid gas IFT measurements carried out by the pendant drop technique under geological storage conditions. We performed IFT measurements for water/H₂S systems over a large range of pressure (up to P = 15 MPa) and temperature (up to T = 120 °C). Water/H₂S IFT decreases with increasing P and levels off at around 9–10 mN/m at high T (≥70 °C) and P (>12 MPa). The latter values are around 30–40% of water/CO₂ IFTs, and around 20% of water/CH₄ IFTs at similar T and P conditions. The IFT between water and a CO₂ + H₂S mixture at T = 77 °C and P > 7.5 MPa is observed to be approximately equal to the molar average IFT of the water/CO₂ and water/H₂S binary mixtures. Thus, when the H₂S content in the stored acid gas increases the capillary entry pressure decreases, together with the maximum height of acid gas column and potential storage capacity of a given geological formation. Hence, considerable attention should be exercised when refilling with a H₂S-rich acid gas a depleted gas reservoir, or a depleted oil reservoir with a gas cap: in the case of hydrocarbon reservoirs that were initially (i.e., at the time of their discovery) close to capillary leakage, acid gas leakage through the caprock will inevitably occur if the refilling pressure approaches the initial reservoir pressure.     

Regulatory challenges and managing public perception in planning a geological storage pilot project in Australia

The implementation of geological storage of CO₂ requires not only further research and development but also the demonstration of carbon dioxide capture and storage (CCS) technology as a viable option. A pilot program is an important first step towards building industry and community confidence in the application of CCS. The Cooperative Research Centre for Greenhouse Gas Technologies (CO2CRC), Australia's leading research organisation in CCS, has initiated a comprehensive research and demonstration program in the Otway Basin in South-West Victoria. As the first project of its kind in Australia, the Otway Basin Pilot Project (OBPP) has faced a number of regulatory and organisational challenges while having to concurrently address public perception. The Otway Basin site with its natural CO₂ accumulations and many depleted natural gas fields offers an appropriate CO₂ storage site to test scientific and regulatory concepts and evaluate public response through social research. The project aims to show that CO₂ can be safely captured, transported and stored deep underground under local conditions, and also monitored and verified. Planning has been ongoing for over a year, baseline studies are underway and the project is targeted to start injection in 2007.     

Hydraulic characterisation of the Stuttgart formation at the pilot test site for CO2 storage, Ketzin, Germany

The paper presents an approach for the interpretation of hydraulic tests of a CO₂ storage reservoir. The sandstone reservoir is characterised by a fluviatile channel structure embedded in a low-permeability matrix. Pumping tests were carried out in three wells, with simultaneous pressure monitoring in each well.The hydraulic parameters (permeability and storativity) and the boundary configurations were calibrated using three different approaches: (i) parameter calibration and type curve interpretation for single-hole tests, (ii) calibration of the entire build-up phase for cross-hole tests, and (iii) calibration of the initial pressure response for cross-hole pumping tests. In addition, the arrival time of the pressure response was determined and provides additional information about the pathways of hydraulic connection.The measured pumping test permeabilities of the formation were much lower than those measured on the cores, which is very unusual. The pumping test permeabilities are mainly between 50 mD and 100 mD (millidarcy), while core samples show a mean aquifer permeability of 500–1100 mD. Based on this it was concluded that some kind of continuous low-permeability structure exists, which was supported by core material. Three possible aquifer configurations were considered. The first and second were derived from traditional pumping test analysis and were conceptualised using flow boundaries. Each of the analyses provides a different result. A method was developed in which these differences were resolved by interpreting the pressure response with respect to its spatial and temporal sensitivity. This solution lead to a third configuration which was mainly based on spatially-variable permeabilities. Taking into account the pumping test results, the geological background and the behaviour of injected CO₂, we consider only the third configuration to be realistic. The results are in good agreement with modelled CO₂ arrival times and pressure history.     

3D geomechanical modelling for CO2 geologic storage in the Dogger carbonates of the Paris Basin

CO₂ injection into a depleted hydrocarbon field or aquifer may give rise to a variety of coupled physical and chemical processes. During CO₂ injection, the increase in pore pressure can induce reservoir expansion. As a result the in situ stress field may change in and around the reservoir. The geomechanical behaviour induced by oil production followed by CO₂ injections into an oil field reservoir in the Paris Basin has been numerically modelled. This paper deals with an evaluation of the induced deformations and in situ stress changes, and their potential effects on faults, using a 3D geomechanical model. The geomechanical analysis of the reservoir–caprock system was carried out as a feasibility study using pressure information in a “one way” coupling, where pressures issued from reservoir simulations were integrated as input for a geomechanical model. The results show that under specific assumptions the mechanical effects of CO₂ injection do not affect the mechanical stability of the reservoir–caprock system. The ground vertical movement at the surface ranges from ?2 mm during oil production to +2.5 mm during CO₂ injection. Furthermore, the changes in in situ stresses predicted under specific assumptions by geomechanical modelling are not significant enough to jeopardize the mechanical stability of the reservoir and caprock. The stress changes issued from the 3D geomechanical modelling are also combined with a Mohr–Coulomb analysis to determine the fault slip tendency. By integrating the stress changes issued from the geomechanical modelling into the fault stability analysis, the critical pore pressure for fault reactivation is higher than calculated for the fault stability analysis considering constant horizontal stresses.     

Re-establishment of the proper injectivity of the CO2-injection well Ktzi 201 in Ketzin, Germany

The onshore CO₂-storage site Ketzin consists of one CO₂-injection well and two observation wells. Hydraulic tests revealed permeabilities between 50 and 100 mD for the sandstone rock units. The designated injection well Ktzi 201 showed similar production permeability. After installation of the CO₂-injection string, an injection test with water yielded a significantly lower injectivity of 0.002 m³/d kPa, while the observation wells showed an injection permeability in the same range as the productivity. Several possible reasons for the severe decline in injectivity are discussed. Acidification of the reservoir interval, injection at high wellhead pressure, controlled mini-fractures and back-production of the well are discussed to remove the plugging material to re-establish the required injectivity of the well. It has been decided to perform a nitrogen lift and analyse the back-produced fluids. Initially during the lift, the back-produced fluids were dark-black. Chemical and XRD analyses proved that the black solids consisted mainly of iron sulphide. Sulphate-reducing bacteria (SRB) were detected in fluid samples with up to 10⁶ cells/ml by fluorescent in situ hybridisation (FISH) indicating that the formation of iron sulphide was caused by bacterial activity. Organic compounds within the drilling mud and other technical fluids were likely left during the well completion process, thus providing the energy source for strong proliferation of bacteria. During the lift, the fraction of SRB in the whole bacterial community decreased from approximately 32% in downhole samples to less than 5%. The lift of Ktzi 201 succeeded in the full restoration of the well productivity and injectivity. Additionally, the likely energy source of the SRB was largely removed by the lifting, thus ensuring the long-term preservation of the injectivity.     

Experimental investigation of the CO2 sealing efficiency of caprocks

Using a combination of experimental (petrophysical and mineralogical) methods, the effects of high-pressure CO₂ exposure on fluid transport properties and mineralogical composition of two pelitic caprocks, a limestone and a clay-rich marl lithotype have been studied. Single and multiphase permeability tests, gas breakthrough and diffusion experiments were conducted under in situ p/T conditions on cylindrical plugs (28.5 mm diameter, 10–20 mm thickness).The capillary CO₂ sealing efficiency of the initially water-saturated sample plugs was found to decrease in repetitive gas breakthrough experiments on the same sample from 0.74 to 0.41 MPa for the limestone and from 0.64 to 0.43 MPa for the marl. Helium breakthrough experiments before and after the CO₂ tests showed a decrease in capillary threshold (snap-off) pressure from 1.81 to 0.62 MPa for the limestone.Repetitive CO₂ diffusion experiments on the marlstone revealed an increase in the effective diffusion coefficient from 7.8 × 10^?11 to 1.2 × 10^?10 m².Single-phase (water) permeability coefficients derived from steady-state permeability tests ranged between 7 and 56 nano-Darcy and showed a consistent increase after each CO₂ test cycle. Effective gas permeabilities were generally one order of magnitude lower than water permeabilities and exhibit the same trend. XRD measurements performed before and after exposure to CO₂ did not reveal any distinct change in the mineral composition for both samples. Similarly, no significant changes were observed in specific surface areas (determined by BET) and pore-size distributions (determined by mercury injection porosimetry). High-pressure CO₂ sorption experiments on powdered samples revealed significant CO₂ sorption capacities of 0.27 and 0.14 mmol/g for the marlstone and the limestone, respectively.The changes in transport parameters in the absence of detectable mineral alterations may be explained by carbonate dissolution and further precipitation along a pH profile across the sample plug which would not be subject to quantitative mineral alteration.     

Seismic monitoring and modelling of supercritical CO2 injection into a water-saturated sandstone: Interpretation of P-wave velocity data

This paper reports on an integrated laboratory and numerical simulation study of ultrasonic P-wave velocity response to supercritical CO₂ displacement of pore water in Tako sandstone. The analysis of dynamic velocity data recorded using an array of piezoelectric transducers mounted on a core sample showed that the P-wave velocities at different positions displayed a similar trend in time, i.e., an initial sharp fall followed by a more gradual decline. Considerable variations observed in the measured P-wave velocity reductions across the sandstone core could largely be attributed to the final state of saturation (e.g. uniform, patchy or in-between) attained by the two-phase fluids. Numerical simulation of the injection test using a simple 1D model was carried out to provide an estimation of the phase saturation changes underlying the measured P-wave velocity reductions. A second order polynomial correlation between the measured ultrasonic P-wave velocity reductions and the estimated CO₂ saturation was established. Comparison with the Gassmann velocities showed that the empirically established relationship marks a clear deviation from both the patchy and uniform saturation velocity curves.     

Numerical investigation concerning the impact of CO2 geologic storage on regional groundwater flow

Large-scale storage of carbon dioxide in saline aquifers may cause considerable pressure perturbation and brine migration in deep rock formations, which may have a significant influence on the regional groundwater system. With the help of parallel computing techniques, we conducted a comprehensive, large-scale numerical simulation of CO₂ geologic storage that predicts not only CO₂ migration, but also its impact on regional groundwater flow. As a case study, a hypothetical industrial-scale CO₂ injection in Tokyo Bay, which is surrounded by the most heavily industrialized area in Japan, was considered, and the impact of CO₂ injection on near-surface aquifers was investigated, assuming relatively high seal-layer permeability (higher than 10 microdarcy). A regional hydrogeological model with an area of about 60 km × 70 km around Tokyo Bay was discretized into about 10 million gridblocks. To solve the high-resolution model efficiently, we used a parallelized multiphase flow simulator TOUGH2-MP/ECO2N on a world-class high performance supercomputer in Japan, the Earth Simulator. In this simulation, CO₂ was injected into a storage aquifer at about 1 km depth under Tokyo Bay from 10 wells, at a total rate of 10 million tons/year for 100 years. Through the model, we can examine regional groundwater pressure buildup and groundwater migration to the land surface. The results suggest that even if containment of CO₂ plume is ensured, pressure buildup on the order of a few bars can occur in the shallow confined aquifers over extensive regions, including urban inlands.     

Screening and selection of sites for CO2 sequestration based on pressure buildup

This paper presents a simple methodology for estimating pressure pressure buildup due to the injection of supercritical CO₂into a saline formation, and the limiting pressure at which the formation starts to fracture. Pressure buildup is calculated using the approximate solution of Mathias et al. [Mathias, S.A., Hardisty, P.E., Trudell, M.R., Zimmerman, R.W., 2009. Approximate solutions for pressure buildup during CO₂ injection in brine aquifers. Transp. Porous Media. doi:10.1007/s11242-008-9316-7], which accounts for two-phase Forchheimer flow (of supercritical CO₂ and brine) in a compressible porous medium. Compressibility of the rock formation and both fluid phases are also accounted for. Injection pressure is assumed to be limited by the pressure required to fracture the rock formation. Fracture development is assumed to occur when pore pressures exceed the minimum principal stress, which in turn is related to the Poisson’s ratio of the rock formation. Detailed guidance is also offered concerning the estimation of viscosity, density and compressibility for the brine and CO₂. Example calculations are presented in the context of data from the Plains CO₂ Reduction (PCOR) Partnership. Such a methodology will be useful for screening analysis of potential CO₂ injection sites to identify which are worthy of further investigation.     

Permanent shallow subsoil CO2 flux chambers for monitoring of onshore CO2 geological storage sites

Public concern over the possibility of migration of stored CO₂ to the surface with resulting damage to vegetation or hazard to humans and animals is a matter which will need to be addressed to be able to satisfy likely regulatory requirements for onshore CO₂ storage in a number of jurisdictions. While soil CO₂ concentration is readily measured continuously and in situ with current technology, the measurement of CO₂ flux at depths below the soil A horizon may be a more sensitive and meaningful technique for early detection of a near surface CO₂ plume. We describe a system for the continuous measurement of soil CO₂ flux at a depth of approximately 1.3 m and present results from three instruments deployed at the Otway Basin Pilot Project in Victoria, Australia and one development system deployed at Sutton, near the Australian Capital Canberra.     

A method for quick assessment of CO2 storage capacity in closed and semi-closed saline formations

Saline aquifers of high permeability bounded by overlying/underlying seals may be surrounded laterally by low-permeability zones, possibly caused by natural heterogeneity and/or faulting. Carbon dioxide (CO₂) injection into and storage in such “closed” systems with impervious seals, or “semi-closed” systems with non-ideal (low permeability) seals, is different from that in “open” systems, from which the displaced brine can easily escape laterally. In closed or semi-closed systems, the pressure buildup caused by continuous industrial-scale CO₂ injection may have a limiting effect on CO₂ storage capacity, because geomechanical damage caused by overpressure needs to be avoided. In this research, a simple analytical method was developed for the quick assessment of the CO₂ storage capacity in such closed and semi-closed systems. This quick-assessment method is based on the fact that native brine (of an equivalent volume) displaced by the cumulative injected CO₂ occupies additional pore volume within the storage formation and the seals, provided by pore and brine compressibility in response to pressure buildup. With non-ideal seals, brine may also leak through the seals into overlying/underlying formations. The quick-assessment method calculates these brine displacement contributions in response to an estimated average pressure buildup in the storage reservoir. The CO₂ storage capacity and the transient domain-averaged pressure buildup estimated through the quick-assessment method were compared with the “true” values obtained using detailed numerical simulations of CO₂ and brine transport in a two-dimensional radial system. The good agreement indicates that the proposed method can produce reasonable approximations for storage–formation–seal systems of various geometric and hydrogeological properties.     

Time-lapse carbon dioxide monitoring with pulsed neutron logging

Elevated levels of CO₂ in the atmosphere have been linked to the rise in land and sea temperature [Climate Change, 2001. In: Houghton, J.T., Ding, Y., Griggs, D.J., Noguer, M., van der Linden, P.J., Xiaosu, D. (Eds.), The Scientific Basis Contribution of Working Group I to the Third Assessment Report of the Intergovernmental Panel on Climate Change (IPCC). Cambridge University Press, UK, p. 944]. To demonstrate geological carbon sequestration as a mitigation technique, a carbon dioxide injection experiment was conducted in East Texas. The target – Frio formation – is a highly porous, permeable and unconsolidated sandstone. The specific interval is the Frio C sand, which originally was saturated with saline formation water. At the injection location, the Frio C sand dips 18° to the south. To monitor the injected CO₂ spreading in the formation, an old well from 1956 drilled into the deeper Yegua formation was selected as the observation well. The injection well was drilled at a distance of 100 ft downdip from the monitoring well. Several borehole measurement methods were available to monitor the CO₂ injection, but the most suitable technology was thought to be the pulsed neutron logging. This logging is used widely in cased hole, and the measured macroscopic thermal absorption cross-section (Σ) is sensitive to CO₂ saturation in high porosity saline water environments. Several log examples are given demonstrating successful the monitoring of the CO₂ plume moving through the two boreholes and the resulting saturation changes.     

Effect of the effective stress coefficient and sorption-induced strain on the evolution of coal permeability: Experimental observations

Permeability is one of the most important parameters for CO₂ injection in coal to enhance coalbed methane recovery. Laboratory characterization of coal permeability provides useful information for in situ permeability behavior of coal seams when adsorbing gases such as CO₂ are injected. In this study, a series of experiments have been conducted for coal samples using both non-adsorbing and adsorbing gases at various confining stresses and pore pressures. Our observations have showed that even under controlled stress conditions, coal permeability decreases with respect to pore pressure during the injection of adsorbing gases. In order to find out the causes of permeability decrease for adsorbing gases, a non-adsorbing gas (helium) is used to determine the effective stress coefficient. In these experiments using helium, the impact of gas sorption can be neglected and any permeability reduction is considered as due to the variation in the effective stress, which is controlled by the effective stress coefficient. The results show that the effective stress coefficient is pore pressure dependent and less than unity for the coal samples studied. The permeability reduction from helium experiments is then used to calibrate the subsequent flow-through experiments using adsorbing gases, CH₄ and CO₂. Through this calibration, the sole effect of sorption-induced strain on permeability change is obtained for these adsorbing gas flow-through experiments. In this paper, experimental results and analyses are reported including how the impact of effective stress coefficient is separated from that of the sorption-induced strain on the evolution of coal permeability.     

Investigations on CO2 storage capacity in saline aquifers—Part 2: Estimation of storage capacity coefficients

Many studies on geological carbon dioxide (CO₂) storage capacity neglect the influence of complex coupled processes which occur during and after the injection of CO₂. Storage capacity is often overestimated since parts of the reservoirs cannot be reached by the CO₂ plume due to gravity segregation and are thus not accessible for storage. This work investigates the effect of reservoir parameters like depth, temperature, absolute and relative permeability, and capillary pressure on the processes during CO₂ injection and thus on estimates of effective storage capacity. The applied statistical characteristics of parameters are based on a large reservoir parameter database. Different measured relative permeability relations are considered. The methodology of estimating storage capacity is discussed. Using numerical 1D and 3D experiments, detailed time-dependent storage capacity estimates are derived. With respect to the concept developed in this work, it is possible to estimate effective CO₂ storage capacity in saline aquifers. It is shown that effective CO₂ mass stored in the reservoir varies by a factor of 20 for the reservoir setups considered. A high influence of the relative permeability relation on storage capacity is shown.     

Dissolution of a CO2 lake, modeled by using an advanced vertical turbulence mixing scheme

The dissolution of CO₂ from a CO₂ lake with and without a hydrate layer, located at a flat bottom at 3000 m depth has been modeled using the MIT General Circulation Model coupled with the General Ocean Turbulence Model (GOTM). The vertical turbulent mixing scheme takes into account density effects and should give more realistic results for the CO₂ plume than previously used constant eddy diffusivity models. The introduction of a third direction gives qualitatively different results for the spreading of the CO₂ plume than previous 2D results. The dissolution rate and near field dissolved CO₂ concentrations approach a steady state for a given far field ocean current within less than a day. The dissolution rate is highly dependent on the velocity of the ambient current and is reduced with 1.6 when a hydrate layer is introduced.     

Long-term variations of CO2 trapped in different mechanisms in deep saline formations: A case study of the Songliao Basin,China

The geological storage of CO₂ in deep saline formations is increasing seen as a viable strategy to reduce the release of greenhouse gases to the atmosphere. There are numerous sedimentary basins in China, in which a number of suitable CO₂ geologic reservoirs are potentially available. To identify the multi-phase processes, geochemical changes and mineral alteration, and CO₂ trapping mechanisms after CO₂ injection, reactive geochemical transport simulations using a simple 2D model were performed. Mineralogical composition and water chemistry from a deep saline formation of Songliao Basin were used. Results indicate that different storage forms of CO₂ vary with time. In the CO₂ injection period, a large amount of CO₂ remains as a free supercritical phase (gas trapping), and the amount dissolved in the formation water (solubility trapping) gradually increases. Later, gas trapping decrease, solubility trapping increases significantly due to the migration and diffusion of CO₂ plume and the convective mixing between CO₂-saturated water and unsaturated water, and the amount trapped by carbonate minerals increases gradually with time. The residual CO₂ gas keeps dissolving into groundwater and precipitating carbonate minerals. For the Songliao Basin sandstone, variations in the reaction rate and abundance of chlorite, and plagioclase composition affect significantly the estimates of mineral alteration and CO₂ storage in different trapping mechanisms. The effect of vertical permeability and residual gas saturation on the overall storage is smaller compared to the geochemical factors. However, they can affect the spatial distribution of the injected CO₂ in the formations. The CO₂ mineral trapping capacity could be in the order of 10 kg/m³ medium for the Songliao Basin sandstone, and may be higher depending on the composition of primary aluminosilicate minerals especially the content of Ca, Mg, and Fe.