焦化厂生化出水电解脱色工艺及其机理的初步研究

针对焦化废水经萃取(蒸氨)脱酚和生化处理后的出水水质的特点,研究用铝板作为电极电解该废水的脱色效果,研究了废水pH、电解槽电压、时间等因素对其色度去除率的影响。结果表明,最佳工艺参数为:pH=4、电解槽电压=10V、时间=30min,此时色度去除率可达93.6%,COD的去除率也可以达到61.78%。采用GCMS分析了电解前后废水中的有机物成分,探讨了形成高色度水质的原因、有机物的去除及脱色机理。     

各种影响因子对电解法预处理医药废水的影响研究

探讨了电解法预处理医药废水时停留时间、电解电压、废水初始浓度、温度和废水pH值等影响因子对去除色度、COD和提高废水可生化性等处理效果的影响，并考察了其应用于工业实际废水处理的可行性。实验结果表明：电解法更适合高浓度医药废水的处理，色度的去除率可达到90％以上；电解时间宜控制在40-60min；电解电压越高，废水COD和色度去除效果越好；在实验温度范围内，温度对色度和COD去除率的影响不大；废水pH值为7．5时电解效果最佳，工程运用宜控制在6—9之间。     

铁屑微电解-共沉淀法处理屠宰场废水的研究

利用铁屑微电解-共沉淀法处理屠宰场废水，介绍其作用机理，考察了废水pH值、铁屑用量、反应时间、曝气时间和操作方式等因素对色度和CODCr去除率的影响。结果表明，在废水pH值为4，铁屑用量为15％，常温反应4h，曝气时间2h条件下，色度去除率可达100％，CODCr去除率达92．68％。     

各种影响因子对电解法预处理医药废水的影响研究

探讨了电解法预处理医药废水时停留时间、电解电压、废水初始浓度、温度和废水pH值等影响因子对去除色度、COD和提高废水可生化性等处理效果的影响,并考察了其应用于工业实际废水处理的可行性.实验结果表明:电解法更适合高浓度医药废水的处理,色度的去除率可达到90%以上;电解时间宜控制在40～60 min;电解电压越高,废水COD和色度去除效果越好;在实验温度范围内,温度对色度和COD去除率的影响不大;废水pH值为7.5时电解效果最佳,工程运用宜控制在6～9之间.     

铁屑微电解法处理水性油墨废水的研究

试验研究了水性油墨废水的铁屑微电解法处理。研究结果表明，微电解条件控制在pH4．0、铁屑投加量10％、反应时间60min、焦炭含量为16．67％，水性油墨废水的处理效果较好，色度去除率可达90％，以上，COD去除率在50％左右。     

黄姜废水的铁炭微电解-混凝预处理研究

研究了高浓度黄姜废水的铁炭微电解-混凝工艺，结果表明，在进水pH4．0、停留时间为40min且有曝气条件下，COD去除率达到64．70％，色度去除率为72．22％，废水的BOD／COD值可由0．29提高到0．56，有利于废水的后续生化处理。     

三维电极-好氧生物法联合处理酸性染料废水模拟研究

采用电解-好氧生物法联合处理酸性大红G模拟废水,三维电解反应器填料为活性炭与玻璃珠混合物,平板电极材料为石墨,通过正交实验确定的最佳实验条件为：电解时间150min,活性炭／玻璃珠体积比为2：1,槽电压20V、pH为5、Na2SO4投加量1．5g／L,进水初始浓度2000mg／L。此时COD去除率及色度去除率分别可达49．78％和81．45％,废水BOD,／COD由0．12提高到0．42。电解后的废水采用生物接触氧化法处理12h后,出水COD为48mg／L,色度120倍,达到综合污水排放二级标准。     

混凝辅助电化学法处理橙黄G染料废水

以石墨板为阳极,研究了电化学氧化法对橙黄G染料废水的降解效果。比较了在NaCl、Na2 SO4以及NaCl与FeSO4·7H2O组合的支持电解质体系中的处理效果,同时考察了电压、初始pH、电解质浓度、电极间距和电解时间等因素对废水中橙黄G脱色率及COD去除率的影响。研究结果表明,橙黄G的脱色主要是活性氯的氧化作用,橙黄G分子的矿化可能主要是电解过程中产生的·OH的作用,FeSO4·7H2O的加入增加了混凝作用,使得处理效果进一步提高。最佳脱色条件下橙黄G脱色率和COD的去除率分别为97．6％和56．3％,B／C（BOD／COD）由0．09提高至0．41,可生化性有较大改善,并且随着降解时间的增加,COD去除率逐渐升高。此结果表明,橙黄G废水COD的去除相对于脱色存在滞后性。     

铁氧电池法处理孔雀石绿的试验研究

提出了铁氧电池法处理孔雀石绿模拟染料废水的方法，研究了曝气时间、pH值、废水体积以及曝气时间与pH值的交互作用对处理结果的影响。试验结果表明，在曝气时间40min，pH=9，废水体积120mL时，COD去除率和脱色率分别达到76．5％和96．5％以上，该方法比传统的铁屑法效果大大提高，应用前景广阔。     

三维电极法深度处理维生素生产废水

采用三维电极法对维生素废水进行深度处理,分别以钛涂钌铱板、铁板和不锈钢板作为电极阳极,石墨板作为电极阴极,柱状活性炭作为粒子电极,结果表明,当以钛涂钌铱板作为阳极,以粒径为1 mm的柱状活性炭作为粒子电极时电解效果最好,COD和色度去除率最高。实验选择电解电压、电极板间距、电解时间和初始pH值作为主要影响因素进行正交实验,实验研究证明,各因素的影响大小为电解电压>电极板间距>电解时间>初始pH值,得到的最佳参数组合分别为:电解电压为10 V,电极板间距为8 cm,电解时间为20 min,初始pH值为4,得到COD和色度最大去除率分别为59.5%和93.57%。     

Chloroaromatic pollutants in mussels incubated in two finnish watercourses polluted by industry

Concentrations of different chlorinated compounds were measured in mussels incubated in two polluted watercourses, a river (the River Kymijoki) and a lake (Lake Vanaja) for four weeks in summer 1995. The sum concentrations of polychlorinated phenols (PCP) and biphenyls (PCB) were both about 1 μg/g lipid weight (lw) in Lake Vanaja mussels, while in the River Kymijoki mussels PCPs were non-detectable and PCBs were measured 120 ng/g lIw. The concentrations of toxic polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) congeners ranged between <17 and 370 pg/g Iw in Lake Vanaja mussels and between <38 and 11,000 pg/g lw in the River Kymijoki mussels. Polychlorinated diphenyl ethers (PCDE) were detected in the mussels incubated in the River Kymijoki (0.4–1.1 ng/g Iw), but not in those incubated in Lake Vanaja. Polychlorinated phenoxyanisoles (PCPA) were measured 33 ng/g lw and polychlorinated phenoxyphenols (PCPP) 300 ng/g lw in the mussels incubated in the River Kymijoki. PCPAs were also detected in reference samples, which were sediment and pike from the River Kymijoki and Baltic salmon, seal and white-tailed sea eagle.     

Evaluation of trichloroethene recovery processes in heterogeneous aquifer cells flushed with biodegradable surfactants

The ability of two biodegradable surfactants, polyoxyethylene (20) sorbitan monooleate (Tween 80) and sodium dihexyl sulfosuccinate (Aerosol MA), to recover a representative dense non-aqueous-phase liquid (DNAPL), trichloroethene (TCE), from heterogeneous porous media was evaluated through a combination of batch and aquifer cell experiments. An aqueous solution containing 3.3% Aerosol MA, 8% 2-propanol and 6 g/l CaCl(2) yielded a weight solubilization ratio (WSR) of 1.21 g TCE/g surfactant, with a corresponding liquid-liquid interfacial tension (IFT) of 0.19 dyn/cm. Flushing of aquifer cells containing a TCE-DNAPL source zone with approximately two pore volumes of the AMA formulation resulted in substantial (>30%) mobilization of TCE-DNAPL. However, a TCE mass recovery of 81% was achieved when the aqueous-phase flow rate was sufficient to displace the mobile TCE-DNAPL toward the effluent well. Aqueous solutions of Tween 80 exhibited a greater capacity to solubilize TCE (WSR=1.74 g TCE/g surfactant) and exerted markedly less reduction in IFT (10.4 dyn/cm). These data contradict an accepted empirical correlation used to estimate IFT values from solubilization capacity, and indicate a unique capacity of T80 to form concentrated TCE emulsions. Flushing of aquifer cells with less than 2.5 pore volumes of a 4% T80 solution achieved TCE mass recoveries ranging from 66 to 85%, with only slight TCE-DNAPL mobilization (<5%) occurring when the total trapping number exceeded 2 x 10(-5). These findings demonstrate the ability of Tween 80 and Aerosol MA solutions to efficiently recover TCE from a heterogeneous DNAPL source zone, and the utility of the total trapping number as a design parameter for a priori prediction of DNAPL mobilization and bank angle formation when flushing with low-IFT solutions. Given their potential to stimulate microbial reductive dechlorination at low concentrations, these surfactants are well-suited for remedial action plans that couple aggressive mass removal followed by enhanced bioremediation to treat chlorinated solvent source zones.     

Book review

The Pesticide Manual ‐ A World Compendium, 8th Edition, C.R. Worthing, Editor and S.B. Walker, Assistant Editor, British Crop Protection Council, BCPC Publications Sales, Bear Farm, Binfield, Bracknell, Berkshire RG12 5QE, England. 1987, 1100 pp., UK £50; Overseas £56. ISBN 0–948404–01–9.     

The variation of street air levels of PAH and other mutagenic PAC in relation to regulations of traffic emissions and the impact of atmospheric processes

The occurrence of particle associated PAH and other mutagenic PAC was determined in 1996 in the street air of Copenhagen. In addition, particle extracts were tested for mutagenicity. The measurements were compared with previous measurements in 1992/1993. The levels had decreased in this period. The decrease was caused by an implementation of light diesel fuels for buses and the exchange of older petrol-driven passenger cars with catalystequipped new ones. About 65% of the reduction was caused by the application of the light diesel fuels. Under special conditions, chemical processes in the atmosphere produced many more mutagens than the direct emissions. The concentrations of S-PAC and N-PAC were 10 times lower than those of PAH, while the levels of oxy-PAH were in the same order of magnitude as those of PAH. Benzanthrone, an oxy-PAH, is proposed to be formed in the atmosphere in addition to direct emissions. Benzo(a)pyrene, often applied as an air quality criteria indicator, was photochemically degraded in the atmosphere. A strong increase in the mutagenic activities was observed to coincide with a depletion of benzo(a)pyrene.     

Organochlorine compounds in a three-step terrestrial food chain

The concentrations of 15 organochlorine chemicals (PCBs and pesticides) were studied in a Central European oak wood food chain system: Great tit (Parus major), caterpillars (Tortrix viridana, Operophtera brumata, Erannis defoliaria), and oak-leaves (Quercus robur). Juvenile tits receive organochlorines from the mother via egg transfer and, eventually to a greater extent, from the caterpillar food source during nestling period. The concentrations of PCB 153 (2,2′,4,4′,5,5′-hexachlorobiphenyl, the most abundant in this study) was found in leaf material at ca. 1 ng/g, in caterpillars 10 ng/g, and in bird eggs 170 ng/g on an average and on a dry mass basis.     

The chemical stability of formulations of some hydrolyzable insecticides in aqueous mixtures with hydrolysis catalysts

Abstract

The active ingredients in commercial formulations of malathion, oxamyl, carbaryl, diazinon, and chlorpyrifos diluted to “spray tank”; concentrations with buffered distilled or natural water of pH 4–9 were stable for at least 24 hr. Formulations of trichlorfon were not stable at pH 7 or above but disappearance rates were slower than for the pure chemical in homogeneous solution. Cupric ion was observed to be an effective catalyst for the hydrolysis of a variety of pure organophosphorus insecticides but did not catalyze hydrolysis of the active ingredients of the formulations examined. Increasing the dilution of the formulation increased the susceptibility of malathion, oxamyl, and carbaryl to hydrolysis.     

Observations on the influence of water and soil pH on the persistence of insecticides

Abstract

The pH‐disappearance rate profiles were determined at ca. 25°C for 24 insecticides at 4 or 5 pH values over the range 4.5 to 8.0 in sterile phosphate buffers prepared in water‐ethanol (99: 1 v/v). Half‐lives measured at pH 8 were generally smaller than at lower pH values. Changes in half lives between pH 8.0 and 4.5 were largest (>1000x) for the aryl carbamates, carbofuran and carbaryl, the oxime carbamate, oxamyl, and the organophosphorus insecticide, trichlorfon. In contrast, half lives of phorate, terbufos, heptachlor, fensulfothion and aldicarb were affected only slightly by pH changes. Under the experimental conditions described half lives at pH8 varied from 1–2 days for trichlorfon and oxamyl to >1 year for fensulfothion and cyper‐methrin. Insecticide persistence on alumina (acid, neutral and basic), mineral soils amended with aluminum sulfate or calcium hydroxide to different pH values and four natural soils of different pH was examined. No correlation was observed between the measured pH of these solids and the rate of disappearance of selected insecticides applied to them. These observations demonstrate the difficulty of extrapolating the pH dependent disappearance behaviour observed in homogeneous solution to partially solid heterogeneous systems such as soil.     

Teratological effects of pesticides in vertebrates: a review

Abstract

In the last decades, the use and misuse of pesticides in the agriculture have increased, having a severe impact on ecosystems and their fauna. Although the various effects of pesticides on biodiversity have been already documented in several studies, to our knowledge no consistent overview of the impact of pesticides in vertebrates, both terrestrial and aquatic, is available. In this review, we try to present a concise compilation of the teratogenic effects of pesticides on the different classes of vertebrates – mammals, birds, reptiles, amphibians and fish.     

Radionuclides in pinon pine (Pinus edulis) nuts from los alamos national laboratory lands and the dose from consumption

Abstract

One of the dominant tree species growing within and around the eastern portion of Los Alamos National Laboratory (LANL), Los Alamos, NM, lands is the pinon pine (Pinus edulis). Pinon pine is used for firewood, fence posts, and building materials and is a source of nuts for food—the seeds are consumed by a wide variety of animals and are also gathered by people in the area and eaten raw or roasted. This study investigated the (1) concentration of ³H, ¹³⁷Cs, ⁹⁰Sr, ^totU, ²³⁸Pu, ^{239, 240}Pu, and²⁴¹ Am in soils (0‐ to 12‐in. [31 cm] depth underneath the tree), pinon pine shoots (PPS), and pinon pine nuts (PPN) collected from LANL lands and regional background (BG) locations, (2) committed effective dose equivalent (CEDE) from the ingestion of nuts, and (3) soil to PPS to PPN concentration ratios (CRs). Most radionuclides, with the exception of ³H in soils, were not significantly higher (p < 0.10) in soils, PPS, and PPN collected from LANL as compared to BG locations, and concentrations of most radionuclides in PPN from LANL have decreased over time. The maximum net CEDE (the CEDE plus two sigma minus BG) at the most conservative ingestion rate (10 lb [4.5 kg]) was 0.0018 mrem (0.018 μSv); this is far below the International Commission on Radiological Protection (all pathway) permissible dose limit of 100 mrem (1000 μSv). Soil‐to‐nut CRs for most radionuclides were within the range of default values in the literature for common fruits and vegetables.     

Degradation and sorption of imidacloprid in dissimilar surface and subsurface soils

Degradation and sorption/desorption are important processes affecting the leaching of pesticides through soil. This research characterized the degradation and sorption of imidacloprid (1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine) in Drummer (silty clay loam) and Exeter (sandy loam) surface soils and their corresponding subsurface soils using sequential extraction methods over 400 days. By the end of the incubation, approximately 55% of imidacloprid applied at a rate of 1.0 mg kg^?1 degraded in the Exeter sandy loam surface and subsurface soils, compared to 40% of applied imidacloprid within 300 days in Drummer surface and subsurface soils. At the 0.1 mg kg^?1 application rate, dissipation was slower for all four soils. Water-extractable imidacloprid in Exeter surface soil decreased from 98% of applied at day 1 to > 70% of the imidacloprid remaining after 400 d, as compared to 55% in the Drummer surface soil at day 1 and 12% at day 400. These data suggest that imidacloprid was bioavailable to degrading soil microorganisms and sorption/desorption was not the limiting factor for biodegradation. In subsurface soils > 40% of ¹⁴C-benzoic acid was mineralized over 21 days, demonstrating an active microbial community. In contrast, cumulative ¹⁴CO₂ was less than 1.5% of applied ¹⁴C-imidacloprid in all soils over 400 d. Qualitative differences in the microbial communities appear to limit the degradation of imidacloprid in the subsurface soils.