Utilization of textile effluent wastewater treatment plant sludge as brick material

In the present work, the feasibility of using sludge generated in wastewater treatment plants of textile industry as a partial replacement for clay in the conventional brick manufacturing process is examined. Physico-chemical properties of the sludge and clay were studied. The characteristics of bricks with replacement of sludge (0–50 %) with an increment of 3 % were determined. All the brick samples satisfied the requirements of Indian Standards norms in terms of weight loss on ignition. The bricks with sludge up to 15 % satisfied the prescribed norms for compressive strength and water absorption. Results also showed that the brick weight loss on ignition was mainly attributed to the organic matter content in the sludge being burnt off during the firing process. The characteristics of bricks such as efflorescence, density and weight loss on ignition for bricks with replacement of clayey soil with textile sludge up to 15 % also satisfied the requirements of the Indian Standard. Thus, textile sludge up to 15 % can be effectively added to make brick material.     

Extracting humic acids from digested sludge by alkaline treatment and ultrafiltration

The concentration of hardly biodegradable humic substances in sludge would relatively increase after anaerobic digestion due to the degradation of other organic substances. Thus, extracting humic substances from digested sludge as a liquid organic fertilizer was tested using alkaline treatment and ultrafiltration, and the dewaterability of the residual sludge was also tested. The results showed that the contents of humic acids and fulvic acids in digested sludge were 16.4 mg/g total solids and 88.9 mg/g total solids, respectively, and most of the humic acids had a molecular weight higher than 50 kDa. Hence, the membrane with a molecular weight cut-off of 50 kDa was used for humic acids recovery from the centrifugation supernatant after alkaline sludge disintegration with an optimum NaOH dose of 0.1 mol/L. Under these conditions, the total concentration of humic acids and fulvic acids was 4239 mg/L in the retention solution, which can be further concentrated and processed for liquid fertilizer. The total recovery rate of sludge humic acids and fulvic acids was about 25 %. The dewatering performance of the residual sludge was better than that of the untreated sludge when the residual sludge was diluted to a water content of 95–98 % and then conditioned with polyacrylamide at a dose of 10–30 mg/L.     

Biodegradation characteristics of organic matters in swine carcasses under different initial operating conditions of simulated anaerobic lysimeter

This study was aimed to investigate the biodegradation characteristics of organic matters in swine carcasses. The lysimeters were simulated with different initial operating conditions: 30 % volumetric moisture content and no sludge addition for lysimeter A (control), 30 % volumetric moisture content and anaerobic sludge addition for lysimeter B, and 40 % volumetric moisture content and anaerobic sludge addition for lysimeter C. The degradation efficiency (18.4 %) of lysimeter B was higher than that (15.2 %) of lysimeter A due to anaerobic sludge addition. Lysimeter B showed higher CH₄ yield (15.6 L/kg VS) and CH₄ production rate (0.41 L/kg VS days) compared to lysimeter A by 31 % and 14 %, respectively. In addition, the degradation efficiency improved from 18.4 % (lysimeter B) to 26.3 % (lysimeter C) by increasing volumetric moisture content. The CH₄ yield (22.9 L/kg VS) and CH₄ production rate (0.68 L/kg VS days) of lysimeter C were higher than those of lysimeter B, respectively. Total organic carbon (TOC) removed in lysimeter C was converted to leachate (20.3 %) and gas (6.0 %), whose values were higher than those of lysimeter A and B. These results demonstrated that the proper control of initial operating conditions could accelerate the anaerobic degradation of organic matters in swine carcasses.     

Pilot study of intense dewatering of urban sewage sludge

Urban sewage sludge treatment has become a severe problem due to its large quantities and enrichment with heavy metals, refractory organic contaminants and pathogenic bacteria. Accordingly, it is essential to develop an effective and low-cost intense dewatering technique to decrease sludge water content so that it can be easily treated by subsequent incineration, landfilling or composting. In this study, a new intense sludge dewatering technique using conditioner of coagulant and flocculant (polyacrylamide) mixture and the diaphragm filter press was developed and investigated systematically by measuring the water content, calorific value and coliform bacteria in the sludge and investigating the dewatering efficiency under different conditions. The results showed that the water content of the sludge was effectively reduced from 80 % to the minimum of 43.6 % by adding conditioners and subsequent dewatering using the diaphragm press. Moreover, the low calorific value of dewatered sludge increased significantly from that of the original sludge, and was conducive to subsequent incineration. The water content of the dewatered sludge cake decreased to less than 25 % after being kept in the open air for 9 days. Therefore, it is proposed that this technique be applied to large-scale engineering applications.     

Bioconversion of industrial wastes: paint sludge from automotive manufacturing

The compostability of water-based paint sludge originating from the automotive industry was investigated. Six reactors were operated. Wastewater treatment sludge from the same industry was used as additional substrate, and corncob was used as a bulking agent. The level of paint sludge within the compost mixtures varied between 55 and 85%. All reactors yielded a temperature increase up to thermophilic phase levels (>?40 °C) for a minimum of 5 days, and organic matter and C/N losses were observed. BTEX concentrations decreased during composting. Nickel and tin levels in the final product exceeded the legal compost limits. The calorific value of the compost mixtures increased from 9532 to 18774 kJ/kg at the end of the composting process. It was seen that the process applied in this study can be utilized as a biodrying step before the usage of paint sludge at cement kilns as additional fuel.     

Sludge earthworm composting technology by Eisenia fetida

Prior to vermicompost application to the soils, there is a need to determine the heavy metal concentrations in the final vermicomposts. Acute toxicity on Eisenia fetida for copper (Cu) and cadmium (Cd) were conducted by artificial soils tests. The dosage of interest is typically the median lethal concentration (LC₅₀) that will kill 50 % of the population of organisms within the test period. The dry artificial soil is pre-moistened 1 or 2 days before the test by adding deionized water to obtain approximately half of the required final water content of 40–60 % of the maximum water holding capacity. The 14-day LC₅₀ values (95 % confidence interval) for Cu and Cd were 530 (450–624) and 1118 (988–1265) mg kg^?1, respectively. The vermicomposting was designed to evaluate the effects of earthworm activity on heavy metals in sewage sludge. Compared with the sludge before vermicomposting by Eisenia fetida, the results are as follows: (1) water content, the pH value and organic matter content decreased, (2) total nitrogen content increased, total phosphorus content and total potassium content decreased, (3) available nitrogen concentration, available phosphorus content increased, and (4) the total content of five metals (Cu, Ni, Cd, Pb and Zn) decreased, and the bioaccumulation factor shows that vermicomposting can efficiently remove heavy metals. Therefore, it can be concluded that the soil use of sludge of the Wastewater Treatment Plant in Huaibei is feasible.     

Recycling of electrolytic manganese solid waste in autoclaved bricks preparation in China

China has played a dominant role in global electrolytic manganese metal (EMM) production, accounting for over 98 % of the total world capacity since 2008. However, with the rapid development of the EMM industry and depletion of mineral ores, electrolytic manganese solid waste (EMSW) is piling up, so more large-scale landfills are needed. The environmental problems generated by EMSW pose severe threats to soil and ground water, and have become the hot issues in society. The aim is to consume and recycle EMSW, and the primary route is to make autoclaved bricks. However, less attention has been given to the procedure and strength-forming mechanism of EMSW bricks, not to mention the production line of the brick. On the basis of physical and chemical property analysis, the pretreatment process of EMSW was indispensable to solidify/stabilize the heavy metals, such as Mn, Zn, Cd, Pb, etc.. This paper expatiated on the procedure of making EMSW autoclaved bricks, analyzed in detail the strength formed by different cementitious materials with cement properties, and introduced the practical engineering of EMSW autoclaved bricks. The results showed that the pretreatment process with quicklime was effective in solidifying/stabilizing the heavy metals. The compressive strength of EMSW bricks reached 10.05 MPa when quicklime 9 % (w/w) added. Cement may be an ideal cementitious material to create EMSW bricks of high strength in experiments and on the production line. Quicklime and cement used simultaneously produced a lower strength than that when adding cement alone because the gypsum from EMSW and an alkali could generate deleterious effects, e.g., expansion or burst. In the production line of EMSW bricks, an appropriate mix proportion to make high-quality autoclaved bricks was determined: EMSW 30–40 %, cement 10–20 %, and aggregates 40–60 %. The low content of heavy metals tested by toxicity leaching may deduce that the EMSW autoclaved bricks have low environmental risk. However, long-term environmental risk evaluation will be needed, requiring more tests and leaching modeling. Employing EMSW to make high-quality autoclaved bricks may be a promising waste-to-resource strategy.     

Influence of combustion temperature on the performance of sewage sludge ash as a supplementary cementitious material

The potential for using sewage sludge ash (SSA) as a supplementary cementitious material (SCM) has been investigated. Controlled combustion of sewage sludge collected in Croatia from two wastewater treatment plants produced SSA with different characteristics. These were used to substitute for cement in mortar samples. The chemical composition and physical properties of SSA depend on wastewater composition, the sludge treatment process and the combustion temperature. These factors influence the suitability of SSA to be used as a SCM. For three different combustion temperatures (800, 900 and 1000 °C), it was concluded that properties of fresh mortar were not affected while in the hardened state, the most favorable combustion temperature is 900 °C regarding mechanical properties. Regardless of combustion temperature, for all types of SSA used in mortars as cement replacement (up to 30%), the average decrease in both compressive and flexural strength values was less than 8% for every 10% of added SSA. The results presented indicate that using up to 20% replacement of cement by SSA produces mortars that meet the specific technical requirements analyzed in this work.     

Study on optimal energy efficiency of a sludge drying-incineration combined system

Thermal drying is a frequently used technology to further remove the water in dewatered sludge. However, it is an expensive solution due to its highly energy consumption. The combination of sludge drying and incineration system, in which, the energy generated from sludge incineration is reused to sludge drying, can largely save the energy consumption of sludge treatment facilities. A bench-scale paddle sludge dryer was built to study the drying characteristics of sludge. Results show that, a significant fluctuation of sludge drying rate and stirring power emerges at the moisture content of 55–65 %. An energy model was established based on a sludge drying and incineration project. The most reasonable dryness of sludge outlet from sludge dryer and input to sludge incinerator was analyzed, in the purpose of achieving optimal energy efficiency. The mono-incineration of dry sludge can be achieved at 850 °C combustion temperature, when sludge lower heating value (LHV) is about 11213 kJ/kg and moisture content is about 60 % w/w. The effect of operation conditions, including sludge moisture content, LHV, and operation load were analyzed based on the energy model. This energy model could be applied for the improvement of energy efficiency of sludge drying and incineration combined system.     

Synthesis and characterization of drinking water treatment plant sludge-incorporated Portland cement

Kinetic analysis of thermally activated phase transformations in drinking water treatment plant (DWTP) sludge suggests its applicability in the materials of construction. The suggested prediction has already been verified on the sludge-based bricks. The present study deals with incorporating the same sludge in the raw meal for the synthesis of Portland cement clinkers. For this purpose, two raw meals are prepared with varying sludge loadings. The sludge effect on reactivity of the crude mixture is evaluated on the basis of the free lime content sintered at various elevated temperatures. The results of chemical and mineralogical and scanning electron microscopic analyses reveal fine mineralogical contents of Portland clinkers calcined at 1450 and 1500 °C. Moreover, the cements prepared from these clinkers by the introduction of certain proportions of gypsum, depict significant durability. The obtained results elucidate that the studied DWTP sludge-incorporated Portland cement shows considerable potential to be commercialized.     

Recycling of combined coal-biomass ash from electric power plant waste as a cementitious material: characteristics and improvement

Combined coal-biomass ash has an enormous impact on environmental quality near electric power plants. This paper describes an alternative to disposal in which the ash is used to produce cementitious materials. Ash was obtained from combustion of coal and biomass containing four mass ratios of anthracite, bitumen, rice husks, and eucalyptus bark. The cement-forming properties were systematically characterized including compressive strength development, durability, and expansion in water. The ash samples were ground to increase the specific surface area, and then used to partially replace ASTM Type I Portland cement in mixtures containing 15, 30, or 45 % ash by mass. The water-binder material's (Portland cement with or without combined coal-biomass ash) ratios (w/c) were held constant at 45, 55, or 65 % by mass. Types A, B, and D ash behaved similarly, while the properties of type C ash were slightly different. Increasing the ash fraction in Portland cement mixtures increased the water requirement and resulted in lower compressive strength. Thorough mechanical grinding reduced the porosity and significantly enhanced the material properties.     

Effect of High Content of Deinking Paper Sludge (DPS) on the Reinforcement of HDPE

Deinking paper sludge (DPS)/high density polyethylene (HDPE) composites with and without coupling agent (3 % of maleated polyethylene (MAPE)) were manufactured by twin-screw extrusion followed by injection molding with high percentages of DPS (0, 20, 30 and 40 %). The effects of DPS content and MAPE on the mechanical, thermal, and morphological properties of the DPS/HDPE composites were investigated. Increasing DPS content in composites increased the tensile and flexural modulus (E; MOE), tensile and flexural strength (Rm; MOR), while decreased elongation at break and Un-notched impact resistance due to a poor adhesion between the DPS and HDPE. The addition of DPS also improved the thermal stability and increased the composites crystallinity. High content of DPS (40 %) and 3 % MAPE achieved good interfacial adhesion between fibres of DPS and HDPE. Therefore, an increase is observed for Rm, MOR, ductility, and impact toughness.     

Stabilization of chloro-organics using organophilic bentonite in a cement-blast furnace slag matrix.

The application of cement-based stabilisation/solidification treatment to organic-containing wastes is made difficult by the adverse effect of organics on cement hydration. The use of organophilic clays as pre-solidification adsorbents of the organic compounds can reduce this problem because of the high adsorption power of these clays and their compatibility with the cementitious matrix. This work presents an investigation of the effect on hydration kinetics, physico-mechanical properties and leaching behaviour of cement-based solidified waste forms containing 2-chlorophenol and 1-chloronapthalene adsorbed on organophilic bentonites. These were prepared by cation exchange with benzyldimethyloctadecylammonium chloride and trimethyloctadecylammonium chloride. The binder was a 30% pozzolanic cement, 70% granulated blast furnace slag mixture. Several binder-to-bentonite ratios and different concentrations of the organics on the bentonite were used. Kinetics of hydration were studied by measurement of chemically bound water and by means of thermal and calorimetric analyses. Microstructure and other physico-mechanical properties of the solidified forms were studied by means of mercury intrusion porosimetry, scanning electron microscopy and unconfined compressive strength measurement. Leaching was checked by two different leaching tests: one dynamic, on monolithic samples, and the other static, on powdered samples. This study indicates that the incorporation of the organic-loaded bentonite in the binder matrix causes modifications in the hardened samples by altering cement hydration. The effects of the two organic contaminants are differentiated.     

Biodegradability and Mechanical Properties of Poly(vinyl alcohol)-Based Blend Plastics Prepared Through Extrusion Method

Plastic blend materials consisting of poly(vinyl alcohol), glycerol and xanthan or gellan were prepared through laboratory extrusion. Their base mechanical properties were compared with the properties of poly(vinyl alcohol) foil and their biodegradability in soil, compost and both activated and anaerobic sludge were assessed. In samples with lower polysaccharide content (10–21 %w/w) the tensile strength of 15–20 MPa was found; the elongation at break of all blends was relatively close to the parameter of poly(vinyl alcohol) foil. The biodegradability levels of the blends tested corresponded to the content of natural components, and the mineralization of the samples with the highest carbohydrate proportion (42 %) reached 50–78 %, depending on the type of the environment. Complete biodegradation of all samples occurred in activated sludge.     

Cement based solidification/stabilization of arsenic-contaminated mine tailings

Cement was used to solidify/stabilize the abandoned mine tailings contaminated primarily with arsenic (up to 88 mg/kg) and lead (up to 35 mg/kg). Solidified/stabilized (s/s) forms with a range of cement contents, 5–30 wt%, were evaluated to determine the optimal binder content. Unconfined compression strength test (UCS), Korean standard leaching tests, toxicity characteristic leaching procedures (TCLP), and synthetic precipitation leaching procedure (SPLP) were used for physical and chemical characterization of the s/s forms. Addition of 5% cement was enough for the s/s forms to satisfy the UCS requirements (0.35 MPa). The addition of 7.5% cement remarkably reduced the leachability of arsenic in tailings. However, that of lead tends to increase slightly with increase of cement content due to its amphoteric nature. The discussions were made for determination of optimal binder content and for results from different evaluation procedures.     

Hydration and leaching characteristics of cement pastes made from electroplating sludge

The purpose of this study was to investigate the hydration and leaching characteristics of the pastes of belite-rich cements made from electroplating sludge. The compressive strength of the pastes cured for 1, 3, 7, 28, and 90 days was determined, and the condensation of silicate anions in hydrates was examined with the ²⁹Si nuclear magnetic resonance (NMR) technology. The leachabilities of the electroplating sludge and the hardened pastes were studied with the multiple toxicity characteristic leaching procedure (MTCLP) and the tank leaching test (NEN 7345), respectively. The results showed that the electroplating sludge continued to leach heavy metals, including nickel, copper, and zinc, and posed a serious threat to the environment. The belite-rich cement made from the electroplating sludge was abundant in hydraulic β-dicalcium silicate, and it performed well with regard to compressive-strength development when properly blended with ordinary Portland cements. The blended cement containing up to 40% the belite-rich cement can still satisfy the compressive-strength requirements of ASTM standards, and the pastes cured for 90 days had comparable compressive strength to an ordinary Portland cement paste. It was also found that the later hydration reaction of the blended cements was relatively more active, and high fractions of belite-rich cement increased the chain length of silicate hydrates. In addition, by converting the sludge into belite-rich cements, the heavy metals became stable in the hardened cement pastes. This study thus indicates a viable alternative approach to dealing with heavy metal bearing wastes, and the resulting products show good compressive strength and heavy-metal stability.     

Study of the treatment effectiveness of a solidification/stabilization process for waste bearing heavy metals

The sludge from a steel processing unit bearing zinc, lead, iron, and manganese was solidified with ordinary Portland cement. The waste was stabilized in the specimens with a waste/binder ratio range of 0.16–4.0. On the basis of the available leaching and unconfined compressive strength, the performance of the solidified/stabilized waste was compared for different numbers of curing days. It was found that curing up to 28 days resulted in a performance improvement, as shown by less leaching of heavy metals and the increased unconfined compressive strength of the specimen. The treatment effectiveness of the solidification/stabilization process was assessed for the metals Pb, Zn, Fe, and Mn, and was found to be 89%, 95%, 74%, and 90%, respectively, for an optimum ratio of 4.0 after 28 days of curing.     

Use of flue gas desulphurisation (FGD) waste and rejected fly ash in waste stabilization/solidification systems

Stabilization/solidification (S/S) processes have been used as the final treatment step for hazardous wastes prior to land disposal. Fly ash is a by-product of coal-fired power generation; a significant proportion of this material is low-grade, reject material (rFA) that is unsuitable as a cement replacement due to its high carbon content and large particle size (>45 microm). Flue gas desulphurization (FGD) sludge is a by-product from the air pollution control systems used in coal-fired power plants. The objective of this work was to investigate the performance of S/S waste binder systems containing these two waste materials (rFA and FGD). Strength tests show that cement-based waste forms with rFA and FGD replacement were suitable for disposal in landfills. The addition of an appropriate quantity of Ca(OH)2 and FGD reduces the deleterious effect of heavy metals on strength development. Results of TCLP testing and the progressive TCLP test show that cement-rFA-Ca(OH)2 systems with a range of FGD additions can form an effective S/S binder. The Leachability Index indicates that cement-based waste forms with rFA replacement were effective in reducing the mobility of heavy metals.     

Physicochemical and biochemical changes during composting of different mixing ratios of biogas sludge with palm oil mill wastes and biogas effluent

Prior to composting, the composition of palm oil mill wastes were analyzed. Palm empty fruit bunches (PEFB) contained the highest total organic carbon (52.83 % dry weight) while palm oil mill biogas sludge (POMS) and decanter cake (DC) contained higher total nitrogen (3.6 and 2.37 % dry weight, respectively) than the others. In addition, palm oil fuel ash (POFA) had a high amount of phosphorus and potassium (2.17 and 1.93 % dry weight, respectively). The effect of mixture ratio of POMS and other palm oil mill wastes for composting was studied using the mixed culture Super LDD1 as an inoculum. All compost piles turned dark brown and attained an ambient temperature after 40 days incubation. The pH values were stable in the range of 6.9–7.8 throughout the process whereas the moisture content tended to decrease till the end with the final value around 30 %. After 60 days incubation, the mixture ratio of POMS:PEFB:DC at 2:1:1 with the addition of biogas effluent gave the highest quality of the compost. Its nitrogen content was 31.75 % higher than the other treatments that may be a result of growth of ink cap mushroom (Coprinus sp.). This is the first report on the occurrence of this mushroom during composting. In addition, its nutrients (3.26 % N, 0.84 % P and 2.03 % K) were higher than the level of the Organic Fertilizer Standard. The mixed culture Super LDD1 produced the highest activity of CMCase (6.18 Unit/g) and xylanase (11.68 Unit/g) at 9 days fermentation. Therefore, this solid-state fermentation could be employed for production of compost as well as enzymes.     

Immobilization of copper ions laden kaolin waste: influence of thermal treatment on its immobilization in cement paste

This work aims to study the influence of thermal treatment of Cu²⁺ laden kaolin wastes on its immobilization efficiency in cement paste. Compressive strength and toxicity characteristic leaching procedure (TCLP) of 5–20 % kaolin waste blended cement pastes were tested. X-ray diffraction (XRD) results illustrate that adsorption of Cu²⁺ ions modify the crystal structure of kaolinite mineral. Fourier transform infrared (FTIR) results indicate that the adsorption sites on the kaolin surface that were occupied with free water molecules have been replaced with Cu²⁺ ions adsorbed from aqueous solutions. The thermal treatment of kaolin waste improves fixation ratio of Cu²⁺ in cement pastes containing up to 20 % of thermally treated waste. This is due to: pozzolanic activity of calcined kaolin, conversion of leachable adsorbed Cu²⁺ ions into encapsulated unleachable phase that does not retard the hydration of cement as well as adsorption of much of leachable Cu²⁺ ions on surfaces of hydration products and occlusion in its lattice structure as illustrated from XRD, FTIR, thermogravimetric, scanning electron microscopy and TCLP results. The fixation ratio of Cu²⁺ in cement paste blended with 20 % of thermally treated kaolin waste, reaches maximum value of about 97 % compared to 82 % for cement paste blended with 20 % of untreated kaolin waste.