An ultrasonic assisted extraction method to release heavy metals from untreated sewage sludge samples

A rapid ultrasound accelerated sequential extraction procedure has been used to develop sequential extraction proposed by BCR protocol (the community Bureau of Reference now the European Union "Measurement and Testing Programme"). The effects of the ultrasonic treatment on the extraction of Cu, Cd, Cr, Pb, Ni and Zn from untreated sewage sludge collected from industrial site of Hyderabad city (Pakistan) were compared with those obtained from conventional sequentional extraction procedure of modified BCR protocol. In BCR method, each extraction steps takes 10h, where as with the use of compromise sonication conditions in ultrasonic bath, steps 1-3 of the sequential extraction (excluding the hydrogen peroxide digestion in step 3, which was not performed with sonication) could be completed in 30, 30 and 30 min, respectively. Extractable Cd, Cr, Pb and Ni contents were obtained by both comparable methodologies were measured by electrothermal atomic absorption spectrometry (ETAAS), while for Cu and Zn Flame atomic absorption spectrometry (FAAS) was used. The validations of both methods were compared by the analysis of certified reference material of soil amended with sewage sludge (BCR 483). According to statistical evaluation of the results, the proposed accelerated extraction method is valid alternative to conventional shaking with much shorter extraction time with p value <0.05. The overall metal recoveries in steps 1-3 (excluding residual step) were 95-100% of those obtained with the conventional BCR protocol, except for Cu extracted (91.6%) as related to indicative values of Cu in BCR 483 obtained in 1-3 steps. The results of the partitioning study of untreated industrial waste water sewage sludge, indicate that more easily mobilized forms (acid exchangeable) were predominant for Cd and Zn, in contrast, the largest amount of Pb and Cr was associated with the iron/manganese oxide and organic matter/sulphide fractions.     

Chemical and mineralogical forms of Cu and Ni in contaminated soils from the Sudbury mining and smelting region, Canada

Available information on soil contamination by trace elements in the Sudbury Cu/Ni mining and smelting region consists largely of total elemental concentration data. Little is known about the mode of occurrence and behaviour of Cu and Ni (the main metallic contaminants) in the soils of the region. In this study, sequential extraction and Scanning Electron Microscopy and Energy Dispersive X-ray Analysis (SEM/EDX) observations were complementarily used to define Cu and Ni forms in the Sudbury soils, so as to assess metal mobility. Most Cu (on average 75%) was associated with 'non-residual' soil forms, whereas Ni was mainly (on average 60%) associated with inorganic 'residual' forms of a sulphide and oxide nature. Therefore, Cu occurs in the soils in more mobile forms than Ni. Consequently, Cu should be removed from these soils at a faster rate than Ni. This is an unusual finding, because generally Ni is known to be more mobile in soils than Cu. SEM/EDX analysis confirmed the greater Cu mobility by showing that the metal was strongly associated with organic matter and was homogeneously distributed on the clay fraction surfaces. Nickel occurred alone or was associated with Fe oxides in various size fractions. Both elements were found as sulphides but Ni was often included in the silicate matrices of spherical particles in associations with Fe. SEM/EDX observations have shown that Cu and Ni are associated with soil forms which would not have been predicted by the sequential extraction alone, such as carbonaceous material, silicate spheres and carbonate particles, supporting complementary use of the two techniques.     

The sequestration of trace elements by willow (Salix purpurea)—which soil properties favor uptake and accumulation?

The effect of soil properties on trace element (TE) extraction by the Fish Creek willow cultivar was assessed in a 4-month greenhouse experiment with two contrasted soils and two mycorrhizal treatments (Rhizophagus irregularis and natives). Aboveground tissues represented more than 82 % of the willow biomass and were the major sink for TE. Cadmium and Zn were concentrated in leaves, while As, Cu, Ni, and Pb were mostly found in roots. Willow bioconcentration ratios were below 0.20 for As, Cu, Ni, and Pb and reached 10.0 for Cd and 1.97 for Zn. More significant differences in willow biomass, TE concentrations, and contents were recorded between soil types than between mycorrhizal treatments. A slight significant increase in Cu extraction by willow in symbiosis with Rhizophagus irregularis was observed and was linked to increased shoot biomass. Significant regression models between TE in willow and soil properties were found in leaves (As, Ni), shoots (As, Cd, Cu, Ni), and roots (As, Cu, Pb). Most of the explanation was shared between soil water-soluble TE and fertility variables, indicating that TE phytoextraction is related to soil properties. Managing interactions between TE and major nutrients in soil appeared as a key to improve TE phytoextraction by willows.     

In situ immobilization of Cu(II) in soils using a new class of iron phosphate nanoparticles

This study tested the feasibility of using a new class of iron phosphate (vivianite) nanoparticles synthesized using sodium carboxymethyl cellulose (NaCMC) as a stabilizer for in situ immobilization of Cu(II) in soils. Transmission electron microscopy measurements demonstrated that the particle size was about 8.4+/-2.9 nm. Batch tests showed that nano-sized vivianite particles can effectively reduce the leachability and in vitro bioaccessibility of Cu(II) in three representative soils (calcareous, neutral, and acidic) at the low doses of 0.61 and 3.01 mg PO(4) g(-1) soil. The Cu leachability was evaluated by the toxicity characteristic leaching procedure and in vitro bioaccessibility was evaluated by the physiological based extraction test. In the case of soil amendment with nanoparticles in 3.01 mg PO(4) g(-1) soil, Cu leachability reduced 63-87% and Cu concentrations in TCLP extract decreased from 1.74-13.33 mg l(-1) to 0.23-2.55 mg l(-1) after those soils were amended for 56 d. Meanwhile, the bioaccessibility of Cu was reduced by 54-69%. Sequential extraction procedures showed the significant decrease of water soluble/exchangeable Cu(II) and carbonate bound fractions and concomitant increase of Cu residual fraction after the soils were amended with the nanoparticles, suggesting that the formation of copper phosphate minerals through precipitation and adsorption was probably responsible for the decrease of Cu availability in soils. Visual MINTEQ modeling further revealed that Cu(3)(PO(4))(2) and Cu(5)(PO(4))(3)OH were formed in the vivianite-solid Cu(II) system, resulting in the decreased solubility of the Cu(II) in the acidic pH range.     

Leaching characteristics of stabilized/solidified fly ash generated from ash-melting plant

This study was designed to elucidate the leaching characteristics of stabilized/solidified (S/S) fly ash generated by ash-melting. For this study, pH-dependent leaching tests, sequential extraction procedures, and column leaching tests were carried out. The pH-dependent leaching test results for Pb, Cu, and Zn showed that the heavy metal concentrations in the high-pH range were lower than the predicted values for hydroxide and carbonate. During sequential extraction, Cu and Pb were principally distributed in the S/S ashes' organic matter fraction in the chelating agent, suggesting that metals bind to the chelating agent. The percentage of the water-soluble fraction for Pb and Cu was low (<0.2 %). The fly ashes treated with a chelating agent and cement had low leachability potential for metals in the high-pH range. Column tests for S/S fly ashes showed that two leaching stages were distinguishable: one for short time, corresponding to faster metal leaching, and another for the leaching rate. Kinetic speciation was then applied to data obtained from column leaching tests. The first-order reaction/diffusion model showed a better fit for Ca, Pb, and Cu, suggesting that the initial dissolution of soluble compounds, such as metal chloride, was controlled by the first-order reaction (surface wash off). Subsequently, insoluble compounds such as hydroxide or carbonate might penetrate into the porous matrix by diffusion.     

A comparison of physiologically based extraction test (PBET) and single-extraction methods for release of Cu, Zn, and Pb from mildly acidic and alkali soils

In vitro digestion test can be applied to evaluate the bioaccessibility of soil metals by measuring the solubility of the metals in synthetic human digestive tract. Physiologically based extraction test (PBET), composed of sequential digestion of gastric and intestinal phase, is one of the frequently used in vitro digestion tests. In this study, the PBET was chosen to determine the bioaccessibility of Cu, Zn, and Pb in 14 mildly acidic and alkali (pH 5.87–8.30) soils. The phytoavailability of Cu, Zn, and Pb in the same soils was also measured using six single-extraction methods (0.1 M HNO₃, 0.4 M HOAc, 0.1 M NaNO₃, 0.01 M CaCl₂, 0.05 M EDTA, and 0.5 M DTPA). The extraction efficiencies of the methods were compared. The PBET had a strong ability to extract metals from soil, which was much greater than neutral salt extraction and close to dilute acid and complex extraction in spite of the last 2 h neutral intestinal digestion. The amounts of bioaccessible Cu, Zn, and Pb in the gastric phase and in the gastrointestinal phase were both largely determined by the total content of soil Cu, Zn, and Pb. But the results of gastrointestinal digestion reflected more differences resulting from element and soil types than those of gastric digestion did. It was noticed that most of variations in the amounts of soil Cu, Zn, and Pb extracted by EDTA were well explained by the total soil Cu, Zn, and Pb, as same as the PBET. Moreover, the solubility of Cu, Zn, and Pb in the gastric phase and gastrointestinal phase were all positively linearly correlated with the results of EDTA. It was suggested that EDTA extraction can be used to predict the bioaccessibility of Cu, Zn, and Pb in mildly acidic and alkali (pH?>?5.8) soils, and the PBET and EDTA could be applied to measure, in a certain extent, the bioaccessibility and phytoavailability of Cu, Zn, and Pb in mildly acidic and alkali (pH?>?5.8) soils at the same time.     

Evaluation of copper availability to plants in copper-contaminated vineyard soils

The repeated use of copper (Cu) fungicides to control vine downy mildew has led to long-term accumulation of Cu in vineyard soils which now raises the issue of the potential bioavailability of Cu for various living organisms including plant species. The bioavailable Cu can be defined as the portion of soil Cu that can be taken up by roots, for a given plant species. In order to evaluate the bioavailability of Cu to plants, a pot experiment was conducted in glasshouse conditions with a crop species (maize) and 12 soils sampled in the upper horizon of 10 vineyard plots (total Cu ranging from 38 to 251 mg kg-1) and two woodland plots (control soils that had not received any Cu application; total Cu amounting to 20-26 mg kg-1). These soils were selected for their diverse physical (large range of particle size distribution) and chemical (from acid to calcareous soils) properties. After 35 days of growth, plant shoots were harvested for analysis. The roots were separated from soil particles for further analysis. The concentrations of Cu in the roots and aerial parts of the maize were then compared with the amounts of Cu extracted from the soil by a range of conventional extractants. Observed Cu concentrations in maize roots which have grown in contaminated vineyard soils were very high (between 90 and 600 mg kg-1), whereas Cu concentrations in the aerial parts varied only slightly and remained low (< 18 mg kg-1). Root Cu concentrations observed for maize increased with increasing total Cu content in the soil and with decreasing soil CEC. Cu accumulation in maize roots may be as high in calcareous soils as in acid soils, suggesting that soil pH had little influence. In the case of the vineyard soils studied, the lack of correlation found for maize between Cu concentrations in roots and in the aerial parts, suggests that an analysis of the aerial parts would not be a good indicator of plant Cu uptake, as it provides no insight into the real amount of Cu transferred from the soil to the plant. For maize, our results show that extraction with organic complexing agents (EDTA, DTPA) and extraction with ammonium acetate seem to provide a reasonably good estimate of root Cu concentration.     

Use of sequential extraction to assess metal partitioning in soils

The state of heavy metal pollution and the mobility of Cd, Cu, Ni, Cr, Pb and Zn were studied in three texturally different agricultural soil profiles near a Cu-Ni smelter in Harjavalta, Finland. The pseudo-total concentrations were determined by an aqua regia procedure. Metals were also determined after division into four fractions by sequential extraction with (1) acetic acid (exchangeable and specifically adsorbed metals), (2) a reducing agent (bound to Fe/Mn hydroxides), (3) an oxidizing agent (bound to soil organic matter) and (4) aqua regia (bound to mineral structures). Fallout from the smelter has increased the concentrations of Cd, Cu and Ni in the topsoil, where 75-90% of Cd, 49-72% of Cu and 22-52% of Ni occurred in the first two fractions. Slight Pb and Zn pollution was evident as well. High proportions of mobile Cd, Cu and Ni also deeper in the sandy soil, closest to the smelter, indicated some downward movement of metals. The hydroxide-bound fraction of Pb dominated in almost all soils and horizons, while Ni, Cr and Zn mostly occurred in mineral structures. Aqua regia extraction is usefully supplemented with sequential extraction, particularly in less polluted soils and in soils that exhibit substantial textural differences within the profiles.     

Effect of biosolid incorporation to mollisol soils on Cr, Cu, Ni, Pb, and Zn fractionation, and relationship with their bioavailability

Biosolid application to soil may be a supply of nutrients and micronutrients but it may also accumulate toxic compounds which would be absorbed by crops and through them be incorporated to the trophic chain.

The present study deals with the effect of biosolid application on Cr, Cu, Pb, Ni, and Zn in agricultural soils. The procedure used is sequential extraction so that the availability of those metals may be estimated and related to their bioavailability as determined through two indicator plants grown in greenhouse: ryegrass (Lolium perenne L.) and red clover (Trifolium pratense). Results showed that biosolid application to soil increased total Cu and Zn content. Sequential extraction showed that the more labile Zn fractions increased after biosolid application to soil. This was confirmed when assessing the total content of this metal in shoot and root of the plants under study, since a higher content was found in plant tissues, while no significant differences were found for Cu, Cr, Ni, and Pb.     

Copper extraction effectiveness and soil dissolution issues of EDTA-flushing of artificially contaminated soils

Ethylenediaminetetraacetic acid (EDTA) was used as a reference chelating agent in column experiments to investigate the effectiveness of chelant-enhanced flushing of soils artificially contaminated under various conditions (low/high Cu loading, and aging). The associated soil dissolution issues were of particular concern. Dissolution of indigenous Fe/Al oxides, Ca carbonates and organic matter was monitored over the course of flushing. Regardless of contamination condition, above 85% extraction efficiency could be accomplished by 10(-2) and 10(-3)M EDTA-flushing, but not 10(-4)M. The Cu extraction kinetics positively correlated to EDTA concentration but inversely to Cu loading in soils. In addition to extraction from weakly sorbed fractions, a large portion of Cu was extracted from oxide, organic matter and residual fractions, which appears to derive from soil dissolution. Cumulative dissolved amounts of Fe, Al, and Ca were found to reach as high as hundreds of mgkg(-1), which were comparable to Cu contamination. Soil organic matter, which is known to strongly interact with Fe and Al oxides, was also mobilized. The rate and extent of these soil dissolutions were also positively correlated to EDTA concentration. Therefore, the co-extraction of soil minerals and organic matter during chelant-enhanced flushing, which would alter both physical structure and chemical properties of the soils, is detrimental to future land use and deserves greater attention. The concentration of chelating agent is the most crucial factor for an effective soil flushing with minimal damage.     

Particulate copper in soils and surface runoff from contaminated sandy soils under citrus production

Soil contamination by copper (Cu) is a worldwide concern. Laboratory incubation and soil Cu characterization were conducted to examine the effects of external Cu loading and liming on Cu speciation in both bulk soil and particulates of an Alfisol and Spodosol under citrus production. Also, drainage water from the sites was evaluated for dissolved and particulate forms of Cu. Soil available Cu estimated by CaCl₂, NH₄OAc, or Mehlich-3 extraction significantly increased with external Cu loads and decreased with soil pH. Most increases in soil Cu occurred in the exchangeable and oxide-bound fractions. Organically bound Cu was the dominant fraction in both bulk soil and particulates, but more in particulates than bulk soil (P?≤?0.001). Organically bound Cu was highly correlated with total recoverable Cu (P?≤?0.01), increased significantly with external Cu loads (P?≤?0.001), and decreased with soil pH (P?≤?0.05). Lime addition converted part of Cu from available pools to more stable forms. Organically bound Cu complexes were found to dominate in soil solution or surface runoff. These results indicate that most Cu accumulated in the contaminated soils is highly mobile, and thus may impact citrus production and the environment.     

A comparative study of metal pollution and potential eco-risk in the sediment of Chaohu Lake (China) based on total concentration and chemical speciation

Total and extractable concentrations of Cu, Pb, and Zn were determined in surface sediments of west Chaohu Lake (China) by HCl-HNO₃-HF-HClO₄ digestion and an optimized BCR sequential extraction procedure, respectively. The metal pollution was evaluated by the enrichment factor approach, and the potential eco-risk was evaluated by the sediment quality guideline (SQG) and risk assessment code (RAC) assessments. The results indicated that both total and extractable metal concentrations were highly variable and were affected by sediment properties, even though the sediments were predominantly composed of <63-μm particles (>89 %). Enrichment factors of the metals based on the total and extractable concentrations all showed higher values in the northern lake area and decreasing values towards the south. This distribution indicated an input of anthropogenic metals via the Nanfei River. Anthropogenic Cu, Pb, and Zn in surface sediments showed comparable values for each metal based on the total and extractable concentrations, suggesting that anthropogenic Cu, Pb, and Zn resided predominantly in the extractable fractions. Sediment Cu had low eco-risk, and Pb and Zn had medium eco-risk by the SQG assessment, whereas the eco-risk rankings of Cu, Pb, and Zn were medium, low, and low–high, respectively, by the RAC assessment. Referencing to the labile (dilute acid soluble) metal concentrations, we deduced that the eco-risk of Cu may be largely overestimated by the RAC assessment, and the eco-risk of Pb may be largely overestimated by the SQG assessment. Overall, sediments Cu and Pb may pose low eco-risk, and Zn may pose low–high eco-risk.     

Use of the physiologically-based extraction test to assess the oral bioaccessibility of metals in vegetable plants grown in contaminated soil

The oral bioaccessibility of metals in vegetable plants grown on contaminated soil was assessed. This was done using the physiologically-based extraction test (PBET) to simulate the human digestion of plant material. A range of vegetable plants, i.e. carrot, lettuce, radish and spinach, were grown on metal contaminated soil. After reaching maturity the plants were harvested and analysed for their total metal content (i.e. Cr, Cd, Cu, Fe, Mn, Mo, Ni, Pb and Zn) by inductively coupled plasma-mass spectrometry (ICP-MS). The plant samples were then subsequently extracted using an in vitro gastrointestinal approach or PBET to assess the likelihood of oral bioaccessibility if the material was consumed by humans.     

Metal contamination and solid phase partitioning of metals in urban roadside sediments

This study was undertaken to assess the anthropogenic impact on metal concentrations of urban roadside sediments (N = 633) in Seoul city, Korea and to estimate the potential mobility of selected metals (Zn, Cu, Pb, Cr, Ni, and Cd) using sequential extraction. Comparison of metal concentrations in roadside sediments with mean background values in sediments collected from first- or second-order streams in Korea shows that Zn, Cu and Pb are most affected by anthropogenic inputs. The 206Pb/207Pb ratios of roadside sediments (range = 1.1419-1.1681; mean 1.1576 +/- 0.0068) suggest that Pb is mainly derived from industrial sources rather than from leaded gasoline. A five-step sequential extraction of roadside sediments showed that Zn, Cd and to a lesser degree Ni occur predominantly in the carbonate bound fraction, while Pb is highest in the reducible fraction, Cu in the organic fraction, and Cr in the residual fraction. It was found that the concentrations in the readily available exchangeable fraction were generally low for most metals examined, except for Ni whose exchangeable fraction was appreciable (average 15.2%). Considering the proportion of metals bound to the exchangeable and carbonate fractions, the comparative mobility of metals probably decreases in the order of Zn > Ni > Cd > Pb > Cu > Cr. As potential changes of redox state and pH may remobilize the metals bound to carbonates, reducible, and/or organic matter, and may release and flush them through drain networks into streams, careful monitoring of environmental conditions appears to be very important. With respect to ecotoxicity, it is apparent the Zn and Cu pollution is of particular concern in Seoul city.     

Assessment of aided phytostabilization of copper-contaminated soil by X-ray absorption spectroscopy and chemical extractions

Field plots were established at a timber treatment site to evaluate remediation of Cu contaminated topsoils with aided phytostabilization. Soil containing 2600 mg kg⁻¹ Cu was amended with a combination of 5 wt% compost and 2 wt% iron grit, and vegetated. Sequential extraction was combined with extended X-ray absorption fine structure (EXAFS) spectroscopy to correlate changes in Cu distribution across five fractions with changes in the predominant Cu compounds two years after treatment in parallel treated and untreated field plots. Exchangeable Cu dominated untreated soil, most likely as Cu(II) species non-specifically bound to natural organic matter. The EXAFS spectroscopic results are consistent with the sequential extraction results, which show a major shift in Cu distribution as a result of soil treatment to the fraction bound to poorly crystalline Fe oxyhydroxides forming binuclear inner-sphere complexes.     

Enhanced multi-metal extraction with EDDS of deficient and excess dosages under the influence of dissolved and soil organic matter

This study investigated the influence of dissolved and soil organic matter on metal extraction from an artificially contaminated soil. With high concentration of DOM, the extraction of Cu, Zn and Pb was enhanced by forming additional metal-EDDS complexes under EDDS deficiency. However, the enhancement of metal extraction under EDDS excess was probably due to the soil structure being disrupted owing to humic acid enhanced Al and Fe dissolution, which induced more metals dissolving from the soils. Fulvic acid was found to enhance metal extraction to a greater extent compared with humic acid because of its high content of the carboxylic functional group. Cu extraction from the soil with high organic matter content using EDDS was the lowest due to the high binding affinity of Cu to SOM, whereas Zn extraction became the highest because of a preference for EDDS to extract Zn due to the high stability constant of ZnEDDS.     

Elemental analysis of ash residue from combustion of CCA treated wood waste before and after electrodialytic extraction

Element distribution in a combined fly ash and bottom ash from combustion of copper chromate arsenate (CCA) treated wood waste was investigated by scanning electron microscopy (SEM/EDX) before and after electrodialytic extraction. The untreated ash contained various particles, including pieces of incompletely combusted wood rich in Cr and Ca, and irregular particles rich in Si, Al and K. Cr was also found incorporated in silica-based matrix particles. As was associated with Ca in porous (char) particles, indicating that Ca-arsenates had been formed during combustion. Cu was associated with Cr in the incompletely combusted wood pieces and was also found in almost pure form in a surface layer of some matrix particles - indicating surface condensation of volatile Cu species. In treated ash, Ca and As were no longer found together, indicating that Ca-arsenates had been dissolved due to the electrodialytic treatment. Instead particles rich in Ca and S were now found, indicating precipitation of Ca-sulphates due to addition of sulphuric acid in connection with the electrodialytic treatment. Cu and Cr were still found associated with incompletely combusted wood particles and incorporated in matrix particles. Chemical analyses of untreated and treated ash confirmed that most As, but only smaller amounts of Cu and Cr was removed due to the electrodialytic extraction. Overall metal contents in the original ash residue were: 1.4 g As, 2.76 g Cu and 2.48 g Cr, after electrodialytic extraction these amounts were reduced by 86% for As, 15% for Cu and 33% for Cr.     

The solid-solution partitioning of heavy metals (Cu,Zn, Cd,Pb) in upland soils of England and Wales

Ninety-eight surface soils were sampled from the uplands of England and Wales, and analysed for loss-on-ignition (LOI), and total and dissolved base cations, Al, Fe, and trace heavy metals (Cu, Zn, Cd, Pb). The samples covered wide ranges of pH (3.4-8.3) and LOI (9-98%). Soil metal contents measured by extraction with 0.43 mol l-1 HNO3 and 0.1 mol l-1 EDTA were very similar, and generally lower than values obtained by extraction with a mixture of concentrated nitric and perchloric acids. Total heavy metal concentrations in soil solution depend positively upon soil metal content and [DOC], and negatively upon pH and LOI, values of r2 ranging from 0.39 (Cu) to 0.81 (Pb). Stronger correlations (r2=0.76-0.95) were obtained by multiple regression analysis involving free metal ion (Cu2+, Zn2+, Cd2+, Pb2+) concentrations calculated with the equilibrium speciation model WHAM/Model VI. The free metal ion concentrations depend positively upon MHNO3 and negatively upon pH and LOI. The data were also analysed by using WHAM/Model VI to describe solid-solution interactions as well as solution speciation; this involved calibrating each soil sample by adjusting the content of "active" humic matter to match the observed soil pH. The calibrated model provided fair predictions of total heavy metal concentrations in soil solution, and predicted free metal ion concentrations were in reasonable agreement with the values obtained from solution-only speciation calculations.     

Octanol-solubility of dissolved and particulate trace metals in contaminated rivers: implications for metal reactivity and availability

The lipid-like, amphiphilic solvent, n-octanol, has been used to determine a hydrophobic fraction of dissolved and particulate trace metals (Al, Cd, Co, Cu, Mn, Ni, Pb, Zn) in contaminated rivers. In a sample from the River Clyde, southwest Scotland, octanol-solubility was detected for all dissolved metals except Co, with conditional octanol-water partition coefficients, D(ow), ranging from about 0.2 (Al and Cu) to 1.25 (Pb). In a sample taken from the River Mersey, northwest England, octanol-solubility was detected for dissolved Al and Pb, but only after sample aliquots had been spiked with individual ionic metal standards and equilibrated. Spiking of the River Clyde sample revealed competition among different metals for hydrophobic ligands. Metal displacement from hydrophobic complexes was generally most significant following the addition of ionic Al or Pb, although the addition of either of these metals had little effect on the octanol-solubility of the other. In both river water samples hydrophobic metals were detected on the suspended particles retained by filtration following their extraction in n-octanol. In general, particulate Cu and Zn (up to 40%) were most available, and Al, Co and Pb most resistant (<1%) to octanol extraction. Distribution coefficients defining the concentration ratio of octanol-soluble particle-bound metal to octanol-soluble dissolved metal were in the range 10(3.3)-10(5.3)mlg(-1). The presence of hydrophobic dissolved and particulate metal species has implications for our understanding of the biogeochemical behaviour of metals in aquatic environments. Specifically, such species are predicted to exhibit characteristics of non-polar organic contaminants, including the potential to penetrate the lipid bilayer. Current strategies for assessing the bioavailability and toxicity of dissolved and particulate trace metals in natural waters may, therefore, require revision.     

The leachability, bioaccessibility, and speciation of Cu in the sediment of channel catfish ponds

There have been growing concerns about the environmental impact of Cu applied in the catfish pond aquaculture. In this paper, sediments taken from three commercial catfish ponds were studied for content, leachability, bioaccessibility, and speciation of sediment-bound Cu. Results showed that the Cu was concentrated in the top 10 cm of the sediments and the peak Cu concentrations ranged from the background level to about 200 mg/kg. Toxicity characteristic leaching procedure showed only 1-8% of sediment Cu was leachable while bioaccessible Cu, evaluated by physiological based extraction test, accounted for up to 40-85% of total Cu. Due to the high redox potential in the surface sediments, acid-volatile sulfide was not a significant binding phase. The sequential extraction results showed that the residual phase (forms in lattices of primary and secondary minerals) was the major Cu fraction in the first two pond sediments but carbonate-bound, Fe/Mn oxide-bound and organically bound Cu, as well as the residual fraction, seemed equally important in the third pond.