Pd/TiO2-SnO2催化还原硝酸盐效能及反应调控

采用共沉淀法制备了掺杂TiO2的复合载体TiO2-SnO2;浸渍法制备了单金属负载型催化剂Pd/TiO2-SnO2.用X射线衍射（XRD）、X射线光电子能谱（XPS）、比表面仪（BET）和透射电镜（TEM）表征表明Pd和TiO2在SnO2上成单层或亚单层分散,增加了反应活性位.催化剂分散性良好,比表面积为100.8m....     

Pd/CeO2催化水中溴酸盐的加氢还原研究

采用溶胶-凝胶法制备了CeO2载体,以浸渍法和沉积沉淀法制备了负载型催化剂Pd/CeO2.使用透射电镜(TEM)和Zeta电位仪对催化剂进行了表征.结果表明两种材料的等电点都在5.0左右; Pd颗粒在载体表面具有良好的分散性,且Pd负载量越高,Pd颗粒的粒径越大.采用Pd/CeO2催化剂催化溴酸盐加氢还原,发现在溴酸盐初始浓度为0.39mmol/L时,采用沉积沉淀法和浸渍法合成的Pd/CeO2催化剂反应50min后对溴酸盐的去除率分别为100%和71%,表明使用沉积沉淀法合成的催化剂具有较高的催化活性.改变催化剂用量,溴酸盐的催化还原速率不受传质阻力的影响,反应过程符合Langmuir–Hinshelwood模型,即催化还原反应由溴酸盐在催化剂表面的吸附控制.增加Pd的负载量,溴酸盐的还原速率增大.溶液pH值较低时,有利于对溴酸盐的催化还原.     

催化还原脱除地下水中的硝酸盐

本文介绍了催化还原脱除地下水中硝酸盐的原理、催化剂的选择、催化剂的制备等问题。与传统的硝酸盐脱除技术相比 ,催化还原法具有运行时间短以及管理方便等优势 ,但是目前催化剂的活性和选择性还不够理想 ,而且反应过程中还会受到传质等因素的限制     

纳米级Pd/Fe@SiO2复合颗粒对2,4-DCP的还原脱氯研究

为有效抑制纳米级Pd/Fe颗粒的团聚和钝化及改善其表面特性,将纳米SiO_2包覆在Pd/Fe颗粒表面,超声波辐照下液相还原法制备纳米级Pd/Fe@SiO_2复合颗粒,采用TEM、SEM、XRD、EDX及BET表征其物性,以2,4-二氯苯酚(2,4-DCP)为目标污染物,探究其对2,4-DCP的还原脱氯影响因素、降解机理和动力学,结果表明:制备的纳米级颗粒粒径均匀、分散性好,比表面积大;体系中纳米级Pd/Fe投加量、钯化率、TEOS投加量、反应温度及溶液初始pH均会对2,4-DCP的降解效果产生明显影响;并推测出纳米级Pd/Fe@SiO_2复合颗粒对2,4-DCP的降解机理即快速吸附—逐步脱氯—最终脱附释放,其降解符合拟一级动力学关系.     

催化还原脱除地下水中硝酸盐的研究

采用浸渍法制备催化剂Pd-Cu/γ-Al2O3,用BET、ICP、XRD、TEM和EDX对该催化剂进行了表征.以甲酸钠作为还原剂,对催化还原硝酸盐进行了试验研究.结果表明,100 mg·L-1硝酸盐完全反应时总氮的脱除率可以达到87%.催化反应的活性和选择性受pH值、催化剂投加量、甲酸钠浓度和硝酸盐初始浓度等反应条件影响.甲酸钠作为还原剂时只需控制溶液初始pH值,初始pH值过高或过低都会降低催化剂活性;控制初始pH值为4.5,适当降低催化剂投加量和增加甲酸钠的浓度有利于提高催化活性,但选择性会显著降低.初始pH值为4.5时,不同初始浓度硝酸盐的催化还原反应为一级反应.     

纳米Pd/Fe催化甲醇/水中2,2',4,4'-四溴联苯醚(BDE-47)还原脱溴

构建了纳米Pd/Fe催化还原甲醇/水中2,2’,4,4’-四溴联苯醚(BDE-47)反应体系,常压下采用单因素实验系统考察了纳米Pd/Fe催化还原甲醇/水中2,2’,4,4’-四溴联苯醚(BDE-47)的主要影响因素,并分析了BDE-47还原反应的中间产物及终产物.结果表明,纳米Pd/Fe的反应活性随Pd负载率的提高而先升后降;甲醇-水体积比高于50∶50后,BDE-47去除率随甲醇-水体积比升高而降低;在25～40℃内,BDE-47去除率随反应温度的升高而升高,随BDE-47初始浓度的增加而降低,增加纳米Pd/Fe量可提高反应速率;酸性及弱碱性条件有利于BDE-47还原.BDE-47还原主要为脱溴反应,是一个从n溴到(n-1)溴联苯醚的逐步脱溴过程,反应进行90min后,BDE-47分子中溴原子完全被脱除,反应终产物为二苯醚.     

MnOx/TiO2-ZrO2催化剂的制备及低温催化还原NO的研究

采用共沉淀法制备了TiO2-ZrO2复合氧化物,以其为载体采用等体积浸渍法制备了不同负载量的MnOx/Ti02-Zr02催化剂.低温下以NH3为还原剂考察了催化剂选择性催化还原(SCR)NO的活性.借助N2吸附、XRD、热重-差示扫描量热法(TG-DSC)对催化剂进行微观表征和分析.结果表明,负载量为5%时,生成的MnO2高度分散,NO的转化率较高;负载量为10%和15%时,出现MnO2晶相,NO的转化率有所下降.120-240℃、体积空速为10000 h-1的条件下,3种负载量的催化剂上NO转化率均大于90%.     

纳米铁炭复合材料的制备及硝酸盐去除效果的研究

采用液相还原法制备纳米铁炭颗粒,探讨制备过程中搅拌速率、硼氢化钠的投加速率、加炭时间、炭铁比的影响,并对材料进行TEM、SEM、XRD、XPS表征。结果表明:制备的材料为纳米铁炭复合材料,复合材料孔隙多,比较松散,纳米铁颗粒为椭球形,能负载在层状的活性炭上,活性炭能缓解部分纳米铁颗粒的团聚现象;在炭铁比为0.4,硼氢化钠投加速率为20 m L/min,加炭时间为10 min,搅拌速率为500 r/min的最优条件下制备得到的材料,其对硝酸盐氮的去除率为94.3%。     

EDTA优化纳米Pd/Fe对2,4-D的催化脱氯研究

采用EDTA优化纳米Pd/Fe催化脱氯水中2,4-二氯苯氧乙酸(2,4-D),并考察了EDTA投加浓度、pH、钯化率、温度等因素对2,4-D还原的影响.结果表明,EDTA的加入络合了纳米Pd/Fe在催化脱氯过程中生成的铁离子,抑制纳米Pd/Fe颗粒表面钝化层的形成,提高了体系的反应活性.适宜的EDTA浓度、低pH、高钯化率、低温等有利于2,4-D的还原脱氯.当EDTA浓度为25.0 mmol·L-1,纳米铁含量为1.0 g·L-1,初始pH=4.3、钯化率为0.5%,温度为25.0℃,搅拌速率为200 r·min~(-1)时,反应50 min,10.0 mg·L-1的2,4-D去除率及苯氧乙酸(PA)生成率均达到100%.     

Formic acid as an alternative reducing agent for the catalytic nitrate reduction in aqueous media

Formic acid was used for the nitrate reduction as a reductant in the presence of Pd:Cu/γ-alumina catalysts. The surface characteristics of the bimetallic catalyst synthesized by wet impregnation were investigated by SEM, TEM-EDS. The metals were not distributed homogeneously on the surface of catalyst, although the total contents of both metals in particles agreed well with the theoretical values. Formic acid decomposition on the catalyst surface, its influence on solution pH and nitrate removal efficacy was investigated. The best removal of nitrate (50 ppm) was obtained under the condition of 0.75 g/L catalyst with Pd:Cu ratio (4:1) and two fold excess of formic acid. Formic acid decay patterns resembled those of nitrate removal, showing a linear relationship between kf (formic acid decay) and k (nitrate removal). Negligible amount of ammonia was detected, and no nitrite was detected, possibly due to buffering effect of bicarbonate that is in situ produced by the decomposition of formic acid, and due to the sustained release of H2 gas.     

丙烷催化还原脱硝中硫中毒Cu-Ir/H-ZSM-5催化剂的再生

考察了5%H₂/Ar还原再生丙烷催化还原NO_x中硫中毒Cu-Ir/H-ZSM-5催化剂的工艺参数影响,采用N₂吸附、X射线衍射、X射线光电子能谱和氢气程序升温还原等手段研究了催化剂再生行为的构效关系.结果表明,硫中毒Cu-Ir/H-ZSM-5催化剂由于CuSO₄的生成导致催化剂活性位损失,比表面积、微孔面积和孔体积的减小.H₂还原再生的最佳工艺参数为再生温度500℃和再生气体用量42.8L/g_催化剂,再生催化剂的活性可恢复到新鲜催化剂的95%.在最佳再生条件(500℃和42.857L/g_催化剂)下,再生催化剂表面CuSO₄含量最低(0.4%),且再生催化剂的比表面积、微孔面积和孔体积较失活催化剂有较大提高.     

H_2O和SO_2对Cr-Ce/TiO_2催化氧化NO性能的影响

采用浸渍法在最佳制备条件下制备了新型Cr-Ce/TiO2催化剂,并对催化剂进行了BET和XRD表征.同时,考察了反应温度、H2O和SO2对该催化剂催化氧化NO性能的影响,并对中毒催化剂进行了FT-IR分析,讨论了中毒机理.结果表明,Cr-Ce/TiO2催化剂具有良好的NO氧化活性,在空速为10000h-1、O2体积分数8%(φ)、NO进口体积分数700×10-6条件下,反应温度250℃时NO转化率可达到59.7%,330℃时NO转化率可达到最大值80.7%.单独加入10%(φ)H2O或300×10-6(φ)SO2都可使催化剂活性降低,但在较高温度时影响较小.330℃下单独通入SO2和同时通入H2O与SO210h后,由于催化剂表面生成了少量硫酸盐和亚硫酸盐,活性下降并维持在62.4%左右,能够满足对NOx进行高效吸收的要求;停止通入H2O和SO2后,催化剂活性恢复到71.6%,加热处理后活性能进一步恢复到78.5%.该催化剂具有比文献中报道的其它NO氧化催化剂更强的抗H2O和SO2毒化能力.     

Studies on catalytic reduction of nitrate in groundwater

Catalytic reduction of nitrate in groundwater by sodium formate over the catalyst was investigated. Pd-Cu/γ-Al₂O₃ catalyst was prepared by impregnation and characterized by brunauer-emmett-teller (BET), inductive coupled plasma (ICP), X-ray diffraction (XRD), transmission electron microscopy (TEM) and energy dispersive X-ray (EDX). It was found that total nitrogen was effectively removed from the nitrate solution (100 mg/L) and the removal efficiency was 87%. The catalytic activity was affected by pH, catalyst amount used, concentration of sodium formate, and initial concentration of nitrate. As sodium formate was used as reductant, precise control in the initial pH was needed. Excessively high or low initial pH (7.0 or 3.0) reduced catalytic activity. At initial pH of 4.5, catalytic activity was enhanced by reducing the amount of catalyst, while concentrations of sodium formate increased with a considerable decrease in N₂ selectivity. In which case, catalytic reduction followed the first order kinetics. Translated from Acta Scientiae Circumstantiae, 2006, 26(4): 567–571 [译自: 环境科学学报]     

N掺杂TiO_2光催化还原地下水中硝酸盐

以硫酸钛为前驱体,采用水热沉淀法制备TiO2光催化剂,采用扫描电子显微镜(SEM)、X-射线能谱(EDS)、X-射线衍射(XRD)、傅立叶红外光谱仪(FTIR)和光电子能谱仪(XPS)进行表征和分析,考察了硫酸钛浓度、焙烧温度对光催化还原水中硝酸盐活性的影响.结果表明,制备的催化剂为掺杂N的锐钛矿型TiO2.硫酸钛浓度为0.5mol.L-1、焙烧温度为400℃时制备的催化剂活性最佳,反应120min后,硝酸盐转化率为95.8%,中间产物NO--N浓度为0.17mg·mL-1,副产物NH+-N浓度为1.52mg·mL-1.     

Pd/CeO2-Al2O3对烟气中多环芳烃的催化氧化性能研究

采用浸渍法制备了不同负载量及不同钯铈比(Pd:Ce)的Pd/CeO2-Al2O3催化剂,并结合XRD、BET、SEM、O2-TPD和H2-TPR等方法对催化剂的性质进行了表征,研究了所制备的催化剂对燃煤烟气中多环芳烃(PAHs)的催化转化效率.XRD和SEM结果表明,Ce和Pd在Al2O3表面呈高度分散状态,有利于PAHs的催化氧化.BET测试表明,Ce的引入改变了催化剂表面孔径结构,提高其比表面积.O2-TPD和H2-TPR测试表明,适当钯铈比条件下制备的催化剂有较强的储氧能力和活性.催化氧化实验结果表明,所制备的Pd/CeO2-Al2O3催化剂对PAHs具有较高的转化效率,其平均转化率均在80%以上,且PAHs的毒性当量显著降低,钯铈比对PAHs的催化氧化性能影响较大,当催化剂的钯铈比为1:1时,PAHs的转化率最高,可达90%以上.     

Mn/TiO2和Mn-Ce/TiO2低温脱硝催化剂的抗硫性研究

在低温选择性催化还原(SCR)反应条件下考察了烟气残余SO2对Mn/TiO2和Mn-Ce/TiO2催化剂选择性催化还原活性的影响,同时对SO2的影响机理进行了探讨.结果发现,Mn/TiO2催化剂在SO2反应气氛中失活很快,硫铵盐的沉积和活性组分的硫酸化是催化剂失活的重要原因;Ce的加入可以有效地抑制催化剂活性组分的硫酸化,同时还能降低硫酸盐在催化剂表面的稳定性,从而可以提高催化剂的抗硫性.     

Effect of manufacturing methods of AgCl/Al2O3 catalyst on selective catalytic reduction of NOx

The AgCl/Al2O3 catalyst has potential for use in the selective catalytic reduction (SCR) of NOx. A compound hydrocarbon, following oxygenation is used as a type of reducing agent. In this experiment, the AgCl/Al2O3 catalyst was produced by four different methods, and the differences among their reduction catalysis of NOx were compared. Ethanol was used as a type of reducing agent. X-ray diffraction analysis was performed to study the crystalline structure and scanning electron microscope and transmission electron microscope (TEM) were applied to determine the microindentation. The results indicated that, in the range of 350–400°C, there was no significant difference on the NOx reduction rate; however, there was dispersion at high and low temperature ranges. The size of the AgCl particles was about 20–100 nm.