城市生活污泥和矿化垃圾中氮磷淋失的模拟研究

通过模拟土柱实验,分析了城市生活污泥和矿化垃圾中氮磷的迁移对地下水的影响以及矿化垃圾对氮磷的去除特性.测定项目包括总磷、总氮、硝态氮、pH和电导率(EC).结果表明:施用污泥和矿化垃圾后淋滤液的pH呈下降趋势;EC和总氮都有显著增加;硝态氮增加特别明显,容易造成地下水污染;总磷变化不大,污染地下水的可能性较小.矿化垃圾对氮的去除作用不明显,反而增加了淋滤液中的氮素含量,但对磷的去除效果明显.因此,在利用矿化垃圾取代土壤时,应注意矿化垃圾中氮特别是硝态氮的污染.     

离子交换法选择性回收污泥厌氧消化液中的磷

为探讨高效选择性回收污泥厌氧消化液中磷的离子交换方法,采用静态实验和动态实验研究了4种阴离子交换树脂（D213、D202、D301和DSQ）的磷回收性能,筛选了适合富磷污泥厌氧消化液选择性磷回收的高交换容量树脂。实验结果表明,D213、D202、D301和DSQ 4种树脂对正磷浓度为70 mg/L的厌氧消化液进行动态处理时,其最大穿透体积分别为3、7、17和90 BV;DSQ树脂磷交换容量远高于其他3种树脂,达到6 860 mg P/L湿树脂,是目前报道的高磷交换容量树脂的3~4倍;DSQ树脂能有效地抵抗厌氧消化液中有机质和硫酸根等阴离子的干扰;用NaOH溶液再生DSQ树脂并回收磷,磷洗脱率超过96%,洗脱液是高浓度含磷液,可作为磷矿石的优质替代品。研究表明,DSQ树脂是一种高效选择性分离磷的树脂,适用于污泥厌氧消化液的磷回收。     

Biodegradation of nonylphenol in sewage sludge

We investigated the effects of various factors on the aerobic degradation of nonylphenol (NP) in sewage sludge. NP (5 mg/kg) degradation rate constants (k₁) calculated were 0.148 and 0.224 day⁻¹ for the batch experiment and the bioreactor experiment, respectively, and half-lives (t_1/2) were 4.7 and 3.1 days, respectively. The optimal pH value for NP degradation in sludge was 7.0 and the degradation rate was enhanced when the temperature was increased and when yeast extract (5 mg/l) and surfactants such as brij 30 or brij 35 (55 or 91 μM) were added. The addition of aluminum sulfate (200 mg/l) and hydrogen peroxide (1 mg/l) inhibited NP degradation within 28 days of incubation. Of the microorganism strains isolated from the sludge samples, we found that strain CT7 (identified as Bacillus sphaericus) manifested the best degrading ability.     

碳酸根对磷酸钙沉淀反应回收磷的影响

以模拟的厌氧消化液为处理对象,通过小试实验,考察不同初始磷浓度Cp、Ca／P物质的量比、pH和温度下,碳酸根（CO3 2-）对磷酸钙沉淀反应回收磷的影响;利用扫描电镜（SEM）、x射线衍射仪（XRD）和傅里叶变换红外光谱（FT．IR）对沉淀产物进行表征。结果表明,高浓度的CO3 2-对以磷酸钙沉淀反应去除和回收磷的效率影响较大;Cp相同时,CO3 2-浓度（CCO3^2-）越大,P的去除率越低,低C,（20mg／L）时尤为显著;当CCO3^2-相同时,随着Cp的增大,反应速率加快,P的去除率逐渐升高,但升高幅度越来越小;增大Ca／P比和pH能提高P的去除率,降低CO3 2-对磷酸钙沉淀反应的抑制作用,综合考虑实际效果,应选择Ca／P比为3．33,pH为9．0作为适宜的反应条件;升高温度对降低CO3 2-对磷酸钙沉淀反应的抑制作用贡献不大。在Cp为60ITIg／L,Ca／P比为1．67,pH为9．0,温度为20℃的条件下,当CCO3^2-为0时,得到的沉淀产物主要为羟基磷灰石HAP;当CCO3^2-为30mmol／L时,得到的沉淀产物为磷酸钙和碳酸合磷灰石的混合物。     

生活污水二级生物处理后的铁盐混凝除磷试验研究

以生活污水二级生物处理后的出水为研究对象,考察了铁盐对浓度在2－4mg/L范围内的总磷的混凝去除效果及影响因素。结果表明,铁盐除磷的最佳pH为7.5-8;铁盐投加量较低时,适当提高GT值可使总磷去除率增加15％－20％;在适当的混凝搅拌条件下,三阶铁盐和聚合硫酸铁对总磷的去除率均在70％以上,混凝后过滤可使出水中总磷降至0.5mg/L以下。     

Occurrence and environmental implications of pharmaceuticals in Chinese municipal sewage sludge

The presence of pharmaceuticals in aquatic environment has become a topic of concern because of their potential adverse effects on human health and wildlife species. A total of 45 dewatered sewage sludge samples were collected throughout China and analyzed for 30 commonly consumed pharmaceutical residues. Ofloxacin was found to be the dominant contaminant with concentrations up to 24 760 μg kg⁻¹, followed by oxytetracycline (5280 μg kg⁻¹), norfloxacin (5280 μg kg⁻¹) and ketoprofen (4458 μg kg⁻¹). The concentration of pharmaceutical residues varied greatly depending on the operation conditions of wastewater treatment plants and sampling locations. Poor agreement was found between the predicted (calculation based on the annual consumption and coefficient of sludge water partition) and detected concentrations of the pharmaceuticals indicating that the occurrence of pharmaceutical residues was affected by various factors such as loading rates, sewage properties and the chemical properties such as the contribution from polar groups. National wide fate and ecotoxicity study is required for the development of control strategies.     

Concentrations and sources of Dechlorane Plus in sewage sludge

Sewage sludge from 31 urban Spanish wastewater treatment plants (WWTP) was analyzed for the emerging halogenated flame retardant Dechlorane Plus (DP). Concentrations of the two major isomers in the technical mixture, syn and anti, ranged between 0.903-19.2 and 1.55-75.1 ng g⁻¹ dry weight, respectively. Overall, concentrations of DP were lower than those of polybrominated diphenyl ethers (PBDEs) (9.10-995 ng g⁻¹ dry weight) and this is likely related to the higher usage of brominated flame retardants. The average ratio of the syn isomer to total DP (f_syn) was 0.28 ± 0.05, which is similar to that of the commercial mixture. Comparing different wastewater treatment methods, we found lower concentrations in those using biological nitrogen and phosphorous elimination, suggesting that DP is susceptible to microbial degradation and that anti-DP is more so, given the enrichment of syn-DP in the sewage sludge. Principal components analysis revealed significant positive correlation (r = 0.619, p < 0.05) between total DP concentrations with the contribution of industrial input to waste streams. This implies release of DP is related to industrial activity, likely stemming from the use of the technical product during manufacture of consumer goods. However, use and disposal of products containing DP could not be dismissed. According to our knowledge, this is the first report on DP in WWTP sludge.     

Feedstock quality and growth of bioenergy crops fertilized with sewage sludge

Sewage sludge is rich in essential plant nutrients, but its use is restricted for crop production due to the pollutants it contains, such as metalloids and heavy metals. Sludge is also very sticky and compact. Therefore, the objectives of this work were to evaluate (1) the impact of various amounts of sludge on bioenergy crop productivity and quality and (2) the use of peat as an adjuvant to reduce the stickiness, density and nutrient richness of the sludge. Three different applications of sludge were examined, high, low (50% of high) and low mixed with an equal volume of peat. The sludge-peat mix increased significantly leaf area and biomass accumulation of maize and hemp. High sludge and sludge-peat mix applications increased significantly the leaf area and biomass accumulation as well as the net photosynthesis of oilseed rape. High sludge application resulted in the highest heavy metal and metalloid accumulation in maize and hemp. Sludge-peat mix resulted in the highest heavy metal and metalloid accumulation in oilseed rape. However, the sludge-peat mix application provided the best feedstock quality in all three crops, since chloride, silicon and sulfur concentrations and ash content in plant material were the lowest of the three sludge treatments.     

Effects of sewage sludge biochar on plant metal availability after application to a Mediterranean soil

Pyrolytic conversion of sewage sludge into biochar could be a sustainable management option for Mediterranean agricultural soils. The aim of this work is to evaluate the effects of biochar from sewage sludge pyrolysis on soil properties; heavy metals solubility and bioavailability in a Mediterranean agricultural soil and compared with those of raw sewage sludge. Biochar (B) was prepared by pyrolysis of selected sewage sludge (SL) at 500 °C. The pyrolysis process decreased the plant-available of Cu, Ni, Zn and Pb, the mobile forms of Cu, Ni, Zn, Cd and Pb and also the risk of leaching of Cu, Ni, Zn and Cd. A selected Mediterranean soil was amended with SL and B at two different rates in mass: 4% and 8%. The incubation experiment (200 d) was conducted in order to study carbon mineralization and trace metal solubility and bioavailability of these treatments. Both types of amendments increased soil respiration with respect to the control soil. The increase was lower in the case of B than when SL was directly added. Metals mobility was studied in soil after the incubation and it can be established that the risk of leaching of Cu, Ni and Zn were lower in the soil treated with biochar that in sewage sludge treatment. Biochar amended samples also reduced plant availability of Ni, Zn, Cd and Pb when compared to sewage sludge amended samples.     

Effects of sewage sludge blending on the coal combustion: a thermogravimetric assessment

Combustion of urban sewage sludge together with coal in existing infrastructures may be a sustainable management option energetically interesting for these materials, usually considered wastes. Thermogravimetric analysis was used to study the combustion of a semianthracite coal and the modifications undergone when adding a small percentage (2%, 5%, 10%) of sewage sludge. Both Differential Scanning Calorimetric analysis and Differential Thermogravimetry burning profiles showed differences between coal and sewage sludge combustion. However, the effects of adding a percentage of sewage sludge equal or smaller than 10% was hardly noticeable in terms of heat release and weight loss during the coal combustion. This was further proved by non-isothermal kinetic analysis, which was used to evaluate the Arrhenius activation energy corresponding to the co-combustion of the blends. This work shows that thermogravimetric analysis may be used as an easy rapid tool to asses the co-combustion of sewage sludge together with coal.     

Phosphorus recovery from fosfomycin pharmaceutical wastewater by wet air oxidation and phosphate crystallization

Fosfomycin pharmaceutical wastewater contains highly concentrated and refractory antibiotic organic phosphorus (OP) compounds. Wet air oxidation (WAO)-phosphate crystallization process was developed and applied to fosfomycin pharmaceutical wastewater pretreatment and phosphorus recovery. Firstly, WAO was used to transform concentrated and refractory OP substances into inorganic phosphate (IP). At 200 °C, 1.0 MPa and pH 11.2, 99% total OP (TOP) was transformed into IP and 58% COD was reduced. Subsequently, the WAO effluent was subjected to phosphate crystallization process for phosphorus recovery. At Ca/P molar ratio 2.0:1.0 or Mg/N/P molar ratio 1.1:1.0:1.0, 99.9% phosphate removal and recovery were obtained and the recovered products were proven to be hydroxyapatite and struvite, respectively. After WAO-phosphate crystallization, the BOD/COD ratio of the wastewater increased from 0 to more than 0.5, which was suitable for biological treatment. The WAO-phosphate crystallization process was proven to be an effective method for phosphorus recovery and for fosfomycin pharmaceutical wastewater pretreatment.     

Towards global phosphorus security: a systems framework for phosphorus recovery and reuse options

Human intervention in the global phosphorus cycle has mobilised nearly half a billion tonnes of the element from phosphate rock into the hydrosphere over the past half century. The resultant water pollution concerns have been the main driver for sustainable phosphorus use (including phosphorus recovery). However the emerging global challenge of phosphorus scarcity with serious implications for future food security, means phosphorus will also need to be recovered for productive reuse as a fertilizer in food production to replace increasingly scarce and more expensive phosphate rock. Through an integrated and systems framework, this paper examines the full spectrum of sustainable phosphorus recovery and reuse options (from small-scale low-cost to large-scale high-tech), facilitates integrated decision-making and identifies future opportunities and challenges for achieving global phosphorus security. Case studies are provided rather than focusing on a specific technology or process. There is no single solution to achieving a phosphorus-secure future: in addition to increasing phosphorus use efficiency, phosphorus will need to be recovered and reused from all current waste streams throughout the food production and consumption system (from human and animal excreta to food and crop wastes). There is a need for new sustainable policies, partnerships and strategic frameworks to develop renewable phosphorus fertilizer systems for farmers. Further research is also required to determine the most sustainable means in a given context for recovering phosphorus from waste streams and converting the final products into effective fertilizers, accounting for life cycle costs, resource and energy consumption, availability, farmer accessibility and pollution.     

Long-term study of palladium in road tunnel dust and sewage sludge ash

The present work summarizes data about palladium contents of road tunnel dust from 1994 to 2007 and sewage sludge ash from 1972 to 2006. Since palladium is emitted from automotive catalytic converters as elemental particles, road dust is quiet useful to study traffic-related Pd emissions. Very high Pd values of up to 516 μg Pd kg⁻¹ were found in the road dust samples collected in 2007. Heavy metals of all urban emissions, also dental practice effluent, are enriched in sewage sludge ash and thus this matrix is useful for the documentation of palladium emission caused by the use of Pd alloys in dental medicine. In sewage sludge ash highest Pd contents of maximum 460 μg Pd kg⁻¹ were found in the years 1986-1997. In both matrices correlations of Pd content to Pd demand of industry are discussed.     

Effects of sewage sludge amendment on heavy metal accumulation and consequent responses of Beta vulgaris plants

Use of sewage sludge, a biological residue produced from sewage treatment processes in agriculture is an alternative disposal technique of waste. To study the usefulness of sewage sludge amendment for palak (Beta vulgaris var. Allgreen H-1), a leafy vegetable and consequent heavy metal contamination, a pot experiment was conducted by mixing sewage sludge at 20% and 40% (w/w) amendment ratios to the agricultural soil. Soil pH decreased whereas electrical conductance, organic carbon, total N, available P and exchangeable Na, K and Ca increased in soil amended with sewage sludge in comparison to unamended soil. Sewage sludge amendment led to significant increase in Pb, Cr, Cd, Cu, Zn and Ni concentrations of soil. Cd concentration in soil was found above the Indian permissible limit in soil at both the amendment ratios.

The increased concentration of heavy metals in soil due to sewage sludge amendment led to increases in heavy metal uptake and shoot and root concentrations of Ni, Cd, Cu, Cr, Pb and Zn in plants as compared to those grown on unamended soil. Accumulation was more in roots than shoots for most of the heavy metals. Concentrations of Cd, Ni and Zn were more than the permissible limits of Indian standard in the edible portion of palak grown on different sewage sludge amendments ratios. Sewage sludge amendment in soil decreased root length, leaf area and root biomass of palak at both the amendment ratios, whereas shoot biomass and yield decreased significantly at 40% sludge amendment. Rate of photosynthesis, stomatal conductance and chlorophyll content decreased whereas lipid peroxidation, peroxidase activity and protein and proline contents, increased in plants grown in sewage sludge-amended soil as compared to those grown in unamended soil.

The study clearly shows that increase in heavy metal concentration in foliage of plants grown in sewage sludge-amended soil caused unfavorable changes in physiological and biochemical characteristics of plants leading to reductions in morphological characteristics, biomass accumulation and yield. The study concludes that sewage sludge amendment in soil for growing palak may not be a good option due to risk of contamination of Cd, Ni and Zn and also due to lowering of yield at higher mixing ratio.     

Conditioning of sewage sludge by Fenton's reagent combined with skeleton builders

Physical conditioners, often known as skeleton builders, are commonly used to improve the dewaterability of sewage sludge. This study evaluated a novel joint usage of Fenton’s reagent and skeleton builders, referred to as the F-S inorganic composite conditioner, focusing on their efficacies and the optimization of the major operational parameters. The results demonstrate that the F-S composite conditioner for conditioning sewage sludge is a viable alternative to conventional organic polymers, especially when ordinary Portland cement (OPC) and lime are used as the skeleton builders. Experimental investigations confirmed that Fenton reaction required sufficient time (80 min in this study) to degrade organics in the sludge. The optimal condition of this process was at pH = 5, Fe²⁺ = 40 mg g⁻¹ (dry solids), H₂O₂ = 32 mg g⁻¹, OPC = 300 mg g⁻¹ and lime = 400 mg g⁻¹, in which the specific resistance to filtration reduction efficiency of 95% was achieved.     

Monitoring heavy metal concentrations in leachates from a forest soil subjected to repeated applications of sewage sludge

The aim of the study was to establish whether the repeated application of sewage sludge to an acid forest soil (Dystric Cambisol) would lead to short-term groundwater contamination. Sludge was applied at four loading rates (0, 2.4, 17 and 60 Mg ha⁻¹) in two consecutive years and leachates were analysed. Heavy metal inputs to soils at the lowest dose were below EC regulations but, at higher doses, limits for Zn, Cd, Cr and Ni were exceeded. Repeated application of sludge at 60 Mg ha⁻¹ resulted in significantly (P < 0.05) higher concentrations of Zn, Cd, Cr and Ni in the leachates than with other treatments. The drinking water standards for Cd and Ni were surpassed in all treatments. Control plots were contaminated by groundwater flow despite the existence of buffer zones between plots. This complicated interpretation of the results, highlighting the importance of careful design of this type of experiment.     

Technological options for the management of biosolids

BACKGROUND, AIM, AND SCOPE: Large quantities of biosolids (sewage sludge), which are produced from municipal wastewater treatment, are ever-increasing because of the commissioning of new treatment plants and continuous upgrades of the existing facilities. A large proportion of biosolids are currently landfilled. With increasing pressure from regulators and the general public, landfilling of biosolids is being phased out in many countries because of potential secondary pollution caused by leachate and the emission of methane, a potent greenhouse gas. Biosolids contain nutrients and energy that can be used beneficially. Significant efforts have been made recently to develop new technologies to manage biosolids and make useful products from them. In this paper, we provide a review of the technologies in biosolids management. MATERIALS AND METHODS: A survey of literature was conducted. RESULTS: At present, the most common beneficial use of biosolids is agricultural land application because of inherent fertilizer values found in biosolids. Expansion of land application, however, may be limited in the future because of more stringent regulatory requirements and public concern about food chain contamination in some countries. Perceived as a green energy source, the combustion of biosolids has received renewed interest. Anaerobic digestion is generally a more effective method than incineration for energy recovery, and digested biosolids are suitable for further beneficial use through land application. Although conventional incineration systems for biosolid management generally consume more energy than they produce because of the high moisture content in the biosolids, it is expected that more combustion systems, either monocombustion or cocombustion, will be built to cope with the increasing quantity of biosolids. DISCUSSION: Under the increasingly popular low-carbon economy policy, biosolids may be recognized as a renewable fuel and be eligible for 'carbon credits'. Because ash can be used to manufacture construction materials, combustion can provide a complete management for biosolids. A number of advanced thermal conversion technologies (e.g., supercritical water oxidation process and pyrolysis) are under development for biosolids management with a goal to generate useful products, such as higher quality fuels and recovery of phosphorus. With an ever-increasing demand for renewable energy, growing bioenergy crops and forests using biosolids as a fertilizer and soil amendment can not only contribute to the low-carbon economy but also maximize the nutrient and carbon value of the biosolids. CONCLUSIONS: Land application of biosolids achieves a complete reuse of its nutrients and organic carbon at a relatively low cost. Therefore, land application should become a preferred management option where there is available land, the quality of biosolids meet regulatory requirements, and it is socially acceptable. Intensive energy cropping and forest production using biosolids can help us meet the ever-increasing demand for renewable energy, which can eliminate the contamination potential for food sources, a common social concern about land application of biosolids. In recent years, increasing numbers of national and local governments have adopted more stringent regulations toward biosolid management. Under such a political climate, biosolids producers will have to develop multireuse strategies for biosolids to avoid being caught because a single route management practice might be under pressure at a short notice. Conventional incineration systems for biosolids management generally consume more energy than they produce and, although by-products may be used in manufacturing, this process cannot be regarded as a beneficial use of biosolids. However, biosolids are likely to become a source of renewable energy and produce 'carbon credits' under the increasingly popular, low-carbon economy policy. RECOMMENDATIONS AND PERSPECTIVES: To manage biosolids in a sustainable manner, there is a need for further research in the following areas: achieving a higher degree of public understanding and acceptance for the beneficial use of biosolids, developing cost-efficient and effective thermal conversions for direct energy recovery from biosolids, advancing technology for phosphorus recovery, and selecting or breeding crops for efficient biofuel production.     

泥磷中温蒸馏提取黄磷装置改进效果的研究

针对泥磷中温蒸馏提取黄磷前期实验装置存在的问题,通过对装置的传动齿轮位置移动改进来达到受力平衡和采用机械密封与软填料密封组合的方式对旋转密封接头重新设计,同时检测改进后实验装置的气密性并进行了泥磷中温蒸馏提取黄磷实验。结果表明,在密封性检测实验中,改进后的实验装置3h之后出现负压,比前期实验装置缩短0．5h,冷凝器温度略有下降,压差与前期相比增加约100mm水柱。黄磷提取实验中,改进的实验装置反应时间比前期缩短0．5h,黄磷蒸馏温度下降,压差增大。最终黄磷的回收率为97．1％,比前期实验增加0．2％;纯度为99．95％,比前期实验提高0．01％,砷含量为0．009561％,比前期实验减少0．0019％,黄磷等级达到优等,实验装置的改进是有效的。     

Residues of pharmaceutical products in recycled organic manure produced from sewage sludge and solid waste from livestock and relationship to their fermentation level

In recent years, sludge generated in sewage treatment plants (STPs) and solid waste from livestock being utilized is useful for circulation of nourishment in farmlands as recycled organic manure (ROM). In this study, we determined the residue levels and patterns of 12 pharmaceutical products generated by human activity in the ROMs produced from human waste sludge (HWS), sewage sludge (SS), cattle manure (CM), poultry manure (PM), swine manure (SM) and horse manure (HM).The kind and number of pharmaceutical products detected in ROMs were different. Fluoroquinolones (FQs) were detected at high levels in HWS and SS samples. In addition, the detection frequency and concentration levels of sulfonamides (SAs) in PM and SM were high. Moreover, high concentrations of chlortetracycline (CTC) were found in only SM. These differences reflect specific adherence adsorption of the pharmaceutical products to different livestock and humans. Moreover, it was found that the concentrations of pharmaceutical products and fermentation levels of ROMs had significant positive correlation (r = 0.41, p = 0.024).When the fermentation test of ROM was conducted in a rotary fermentor in a lab scale test, the residue levels of pharmaceutical products decreased effectively except carbamazepine (CBZ). The rates of decrease were in the case of tetracyclines (TCs): 85-92%, FQs: 81-100%, erythromycine: 67%, SAs: 79-95%, trimethoprim: 86% and CBZ: 37% by 30 d. Pharmaceutical products that can be decomposed by fermentation process at the lowest impact of residual antibiotic activities may therefore be considered as environmentally friendly medicines.