表面活性剂冲洗法治理非水相流体污染多相流研究进展

表面活性剂冲洗法是一种治理土壤与地下水非水相流体(NAPLs)污染的有效技术.在简要介绍表面活性剂冲洗法去除作用机理的基础上,总结了近些年来与表面活性剂冲洗法多相流相关的国内外试验研究和模型研究成果,主要包括表面活性剂作用所引起的混溶驱替和不混溶驱替多相流问题,并指出目前研究中存在的问题和进一步探讨的方向.     

表面活性剂冲洗法治理非水卡流体污染多相流研究进展

表面活性剂冲洗法是一种治理土壤与地下水非水相流体（NAPLs）污染的有效技术。在简要介绍表面活性剂冲洗法去除作用机理的基础上，总结了近些年来与表面活性剂冲洗法多相流相关的国内外试验研究和模型研究成果，主要包括表面活性剂作用所引起的混溶驱替和不混溶驱替多相流问题，并指出目前研究中存在的问题和进一步探讨的方向。     

重金属-多氯联苯复合污染土壤同步洗脱

电子垃圾拆解区土壤具有重金属与有机物复合污染的特性,尤其以Cu、Pb、Cd和多氯联苯(PCBs)的复合污染较为突出。为了同步脱除土壤中重金属与PCBs,选用增溶物质:Tween 80、TX-100、SDBS、β-环糊精与螯合剂柠檬酸依次组合进行复合污染土壤淋洗实验,应用批量平衡震荡法研究它们对重金属(Cu、Pb、Cd)与PCBs(Aroclor 1254)的洗脱效果。通过比较洗脱效果、环境友好性等方面,得出非离子表面活性剂Tween 80与天然螯合剂柠檬酸2种淋洗剂复合最佳;进一步研究两者的淋洗先后顺序、浓度配比、洗脱时间及淋洗剂p H对污染土壤洗脱效果的影响,结果表明,在Tween 80和柠檬酸均为10 g/L、p H=6、淋洗时间12 h时淋洗效果达到最佳,对Cu、Pb、Cd及PCBs的洗脱率分别达到98.77%、55.92%、66.82%和58.01%。因此,利用Tween80和柠檬酸组合可同时有效去除土壤重金属和PCBs,是复合污染土壤淋洗修复的有效淋洗剂。     

生物与化学表面活性剂协同洗脱土壤中PCBs的研究

通过序批实验和土柱淋洗实验研究了由生物表面活性剂鼠李糖脂(RL)与非离子化学表面活性剂十二烷基醇聚氧乙烯(6)醚(POE(6))混合得到的复配试剂洗脱污染土壤中多氯联苯(PCBs)的作用效果及其作用机理。结果表明,同一土样中,从批实验得到的PCBs洗脱率略高于土柱淋洗实验。RL与POE(6)两种单一试剂对人工污染土样中的PCBs洗脱率均大于60%,而对陈化土样中的洗脱率均不到20%,且土壤中的TOC含量越高,PCBs的洗脱率越低。在质量浓度为301 mg/L(10 CMC)及1 505 mg/L(50 CMC)的RL-POE(6)复配试剂中,RL与POE(6)对人工污染土壤中PCBs的洗脱具有一定的协同作用。当复配试剂的浓度为301 mg/L时,RL与POE(6)对陈化土样中PCBs的洗脱没有协同作用;但当RL-POE(6)的浓度增加到1 505 mg/L时,RL与POE(6)对陈化土样中PCBs的洗脱具有明显的协同作用。     

鼠李糖脂洗脱土壤中多氯联苯影响因素的研究

研究了由铜绿假单胞菌发酵产生的代表性生物表面活性剂鼠李糖脂（RL）对土壤中PCBs解吸的影响。结果表明,RL的种类与浓度、土壤污染类型、解吸时间、洗脱次数、pH以及离子强度对土壤中PCBs的洗脱有一定的影响,而温度对PCBs的洗脱影响很小。当RL浓度低于CMC时,对PCBs的洗脱没有明显的促进作用;当RL浓度高于CMC后,对PCBs的洗脱有显著的促进作用。具有较低HLB的单鼠李糖脂R2对PCBs的洗脱效果要优于二鼠李糖脂R1。人工污染土壤中PCBs的洗脱效果要高于陈化土壤。污染土壤中TOC的含量越高,PCBs的洗脱率越低。延长解吸时间和增加洗脱次数可增加土壤中PCBs的洗脱率。碱性环境（pH＞7）或增加RL溶液中的离子强度均有利于土壤中PCBs的洗脱。     

比较两种表面活性剂淋洗去除土壤中的重金属

以停车场和湿地2种土壤为研究对象,分别使用表面活性剂鼠李糖脂和月桂基醚硫酸钠对土壤样品进行淋洗,考察2种表面活性剂对这2种土壤中重金属的去除能力差异及形态分布的影响,并分析淋洗后残留在土壤中表面活性剂的生物毒性。结果表明,2种表面活性剂均可在一定程度上去除2种土壤中的Cu、Cd、Pb和Zn。与湿地土壤相比,2种表面活性剂对停车场土壤中重金属的去除率均较高,且月桂基醚硫酸钠的去除能力优于鼠李糖脂。2种表面活性剂对可交换态重金属的去除效果最好,对残渣态重金属去除率较低。淋洗后2种土样中残留的鼠李糖脂及停车场土样中残留的月桂基醚硫酸钠的生物毒性低,湿地土壤中残留的月桂基醚硫酸钠具有一定生物毒性。     

糖脂类生物表面活性剂去除污染含水层中石油烃的研究

研究了糖脂类生物表面活性剂对石油烃的增溶,并将其用于污染含水层中石油烃的去除。结果表明:石油烃溶解度随着糖脂类生物表面活性剂浓度的增大而增大,糖脂类生物表面活性剂质量浓度为1 200mg/L时,石油烃溶解度达10 077.7mg/L;界面张力随着糖脂类生物表面活性剂浓度的增加而减小,糖脂类生物表面活性剂质量浓度为1mg/L时,界面张力为34.3mN/m,糖脂类生物表面活性剂质量浓度为800mg/L时,界面张力为5.2 mN/m。采用糖脂类生物表面活性剂对污染含水层进行清洗处理,在固液比(质量体积比)为1g∶2mL的体系中,糖脂类生物表面活性剂质量浓度为3 000mg/L,120r/min、10℃下振荡12h,石油烃去除率达70.82%。污染含水层柱冲洗结果表明,糖脂类生物表面活性剂质量浓度分别为1 200、3 000mg/L时,10倍孔隙体积的表面活性剂冲洗后,分别从污染砂样中去除41.81%和63.30%的石油烃。     

表面活性剂对焦化污染土壤中多环芳烃淋洗修复研究

异位土壤淋洗是一种高效修复污染土壤技术。以孝义市某焦化厂污染土壤为研究对象,采用批处理实验,探究表面活性剂曲拉通-100(TX-100)、吐温80(TW80)、烷基糖苷(APG)作为淋洗剂对土壤中16种多环芳烃(PAHs)的淋洗效果,并以TW80为代表,考察了淋洗剂浓度、淋洗时间、pH以及淋洗方式对污染土壤中PAHs的去除效果。结果表明,TW80、TX-100和APG对土壤中16种PAHs的总去除率分别为25.67%、18.89%和16.77%。TW80作为淋洗剂,3环PAHs的去除率低于高环(3环)PAHs,主要与焦化污染土壤中以3环PAHs为主有关;高环PAHs随着环数的增加,去除率降低。焦化污染土壤中PAHs的去除在240min达到平衡;大部分PAHs去除率随TW80浓度的增加而增大;pH可不作调整;在TW80用量相同情况下,建议采用单次淋洗。     

表面活性剂对黄土中石油污染物的解吸影响研究

研究了用表面活性剂去除黄土中柴油类污染物。选用阴离子表面活性剂十二烷基苯磺酸钠和十二烷基硫酸钠 (LAS和SDS)和阳离子表面活性剂十六烷基三甲基溴化铵 (CTAB)对污染的土壤进行解吸实验 ,表明阴离子表面活性剂浓度从 0 .1%增加到 1.0 %时 ,其柴油的去除率可达 2 0 % ,而阳离子表面活性剂去除作用不甚明显。利用摩尔增溶比MSR值求得LAS和SDS的logKm 值为 4.5 5 2和 3 .63 0 ,这和理论的计算值很接近     

表面活性剂清洗处理重度石油污染土壤

为了优化表面活性剂清洗处理重度石油污染土壤的方法和具体洗脱条件参数,采集山东省东营市胜利油田污染土壤,研究了阴离子-非离子混合表面活性剂对该土壤中石油类污染物的去除效果。应用化学热洗原理,主要考查了表面活性剂配比、投加量、清洗温度及清洗助剂对去除效果的影响。实验得到的清洗处理最佳条件为：使用LAS与TX-100质量比为8∶2的组合表面活性剂,总表面活性剂浓度为3 g/L,助剂硅酸钠浓度为5 g/L,75℃条件下搅拌1 h。清洗后土壤含油量从20%下降到4.6%,去除率达到76.9%。废水回用实验表明,清洗处理的废水对土壤中石油烃类物质仍有一定的去除效果。废水回用比从30%到100%时,对土壤中石油烃的去除率都可达到55%以上。对废水进行二次回用时仍能去除18.8%的污染物。     

TiO2 photocatalytic degradation of PCBs in soil-water systems containing fluoro surfactant

Titanium dioxide-mediated photodegradation of Polychlorinated biphenyls (PCBs) in soil/aqueous systems with added fluorinated surfactant was investigated. PCBs can bind tightly to organic matter in the soil, especially in aged, contaminated soil. Experiments showed an effective PCB photocatalytic degradation in mixed systems of soil/clay with anionic fluorinated surfactant FC-143 and TiO2. The FC-143 surfactant is stable in this photochemical process. PCB degradation rates in samples followed the order: spiked clay > spiked soil > Hudson River bank soil. The results suggest that anionic fluorinated surfactant may form semimicelles and/or admicelles on the surface of positively charged TiO2. The hydrophobic surface of TiO2 can provide a nonpolar phase that acts as a partioning medium for hydrophobic PCBs. Therefore, PCBs in soil can be released to the semimicelle and/or admicelle on the TiO2 surface and are effectively photodegraded in a dispersion containing anionic fluorinated surfactant. The combination of surfactant extraction and photooxidation forms the basis for a novel two-stage process for the removal and destruction of PCBs from soil.     

Biosurfactant-enhanced solubilization of NAPL mixtures

Remediation of nonaqueous phase liquids (NAPLs) by conventional pump-and-treat methods (i.e., water flushing) is generally considered to be ineffective due to low water solubilities of NAPLs and to mass-transfer constraints. Chemical flushing techniques, such as surfactant flushing, can greatly improve NAPL remediation primarily by increasing the apparent solubility of NAPL contaminants. NAPLs at hazardous waste sites are often complex mixtures. However, the equilibrium and nonequilibrium mass-transfer characteristics between NAPL mixtures and aqueous surfactant solutions are not well understood. This research investigates the equilibrium solubilization behavior of two- and three-component NAPL mixtures (containing akylbenzenes) in biosurfactant solutions. NAPL solubilization is found to be ideal in water (i.e., obeys Raoult's Law), while solubilization in biosurfactant solutions was observed to be nonideal. Specifically, the relatively hydrophobic compounds in the mixture experienced solubility enhancements that were greater than those predicted by ideal enhanced solubilization theory, while the solubility enhancements for the relatively hydrophilic compounds were less than predicted. The degree of nonideality is shown to be a nonlinear function of the NAPL-phase mole fraction. Empirical relationships based on the NAPL-phase mole fraction and/or micelle-aqueous partition coefficients measured in single-component NAPL systems are developed to estimate values for the multicomponent partition coefficients. Empirical relationships that incorporate both the NAPL-phase mole fraction and single-component partition coefficients yield much improved estimates for the multicomponent partition coefficient.     

Investigation of polychlorinated biphenyl removal from contaminated soil using microwave-generated steam

A feasibility study of polychlorinated biphenyl (PCB) removal from contaminated soils using microwave-generated steam (MGS) was performed. Initial experimental results show that MGS effectively removed PCBs from contaminated soil with an overall removal efficiency of greater than 98% at a steam-to-soil mass ratio of 3:1. Removal efficiency was found to be dependent upon the amount of steam employed, expressed as a mass ratio of steam applied to soil mass. Evaporation was identified as a major mechanism in removing PCBs from the soil. Rapid expansion and evaporation of pore water by microwave dielectric heating accelerated evaporation rates of PCB molecules. Increased solubility of PCBs into the heated aqueous phase is also hypothesized. Together these effects increase mass-transfer rates, thus enhancing removal of PCBs from the soil.     

The partitioning and modelling of pesticide parathion in a surfactant-assisted soil-washing system

Soil sorption of organic pollutants has long been a problematic in the soil washing process because of its durability and low water solubility. This paper discussed the soil washing phenomena over a wide range of parathion concentrations and several soil samples at various fractions of organic content (foc) levels. When parathion dosage is set below the water solubility, washing performance is stable for surfactant concentrations above critical micelle concentration (cmc) and it is observed that more than 90% of parathion can be washed out when dosage is five times lower than the solubility limit. However, such trends change when non-aqueous phase liquids (NAPL) is present in the system. Parathion extraction depends very much on the surfactant dosage but is not affected by the levels of foc in the system. In between the extreme parathion dosage, a two-stage pattern is observed in these boundary regions. Washing performance is first increased with additional surfactant, but the increase slows down gradually since the sorption sites are believed to be saturated by the huge amount of surfactant in the system. A mathematical model has included foc to demonstrate such behavior and this can be used as a prediction for extraction.     

In Memoriam

ABSTRACT

A feasibility study of polychlorinated biphenyl (PCB) removal from contaminated soils using microwave-generated steam (MGS) was performed. Initial experimental results show that MGS effectively removed PCBs from contaminated soil with an overall removal efficiency of greater than 98% at a steam-to-soil mass ratio of 3:1. Removal efficiency was found to be dependent upon the amount of steam employed, expressed as a mass ratio of steam applied to soil mass. Evaporation was identified as a major mechanism in removing PCBs from the soil. Rapid expansion and evaporation of pore water by microwave dielectric heating accelerated evaporation rates of PCB molecules. Increased solubility of PCBs into the heated aqueous phase is also hypothesized. Together these effects increase mass-transfer rates, thus enhancing removal of PCBs from the soil.     

Enhanced naphthalene solubility in the presence of sodium dodecyl sulfate: effect of critical micelle concentration

Surfactants can increase the solubility of non-polar compounds, and have been applied in areas such as soil washing and treatment of non-aqueous phase liquids (NAPLs). This investigation explored the feasibility of removing vapor phase polycyclic aromatic hydrocarbon (PAH) from gases using an anionic surfactant. The solubility of vapor phase naphthalene was measured herein using gas chromatograph (GC) with a photon ionization detector (PID). The measurement results indicated that surfactant molecules were not favorable to micelle formation when temperatures increased from 25 degrees C to 50 degrees C. Regardless of whether solutions were quiescent or agitated, equilibrium naphthalene apparent solubility increased linearly with surfactant concentrations exceeding critical micelle concentration (CMC). The pH effects on naphthalene apparent solubility were small. Agitation increased naphthalene apparent solubility and lumped mass transfer coefficients. Furthermore, lumped mass transfer coefficients decreased with increasing surfactant concentration owing to increase in interfacial resistance and viscosity and decreased spherical micelle diffusion coefficients. Finally, the net absorption rate increased because the solubilization effects of micelles exceeded the reduction effects of mass transfer coefficient above the CMC. The enhanced naphthalene apparent solubility from the addition of surfactant can be expressed by an enrichment factor (EF). The EF value of naphthalene for the surfactant solution at 0.1 M with agitation at 270 rpm relative to quiescent water could reach 18.6. This work confirms that anionic surfactant can improve the removal efficiency of hydrophobic organic compound (HOC) from the gas phase.     

Effect of pH control at the anode for the electrokinetic removal of phenanthrene from kaolin soil

Polycyclic aromatic hydrocarbon (PAH)-contaminated soils exist at numerous sites, and these sites may threaten public health and the environment because many PAH compounds are toxic, mutagenic, and/or carcinogenic. PAHs are also hydrophobic and persistent, so conventional remediation methods are often costly or inefficient, especially when the contaminants are present in low permeability and/or organic soils. An innovative technique, electrokinetically enhanced in situ flushing, has the potential to increase soil-solution-contaminant interaction and PAH removal efficiency for low permeability soils; however, the electrolysis reaction at the anode may adversely affect the remediation of low acid buffering capacity soils, such as kaolin. Therefore, the objective of this study was to improve the remediation of low acid buffering soils by controlling the pH at the anode to counteract the electrolysis reaction. Six bench-scale electrokinetic experiments were conducted, where each test employed one of three different flushing solutions, deionized water, a surfactant, or a cosolvent. For each of these solutions, tests were performed with and without a 0.01 M NaOH solution at the anode to control the pH. The test using deionized water with pH control generated a higher electroosmotic flow than the equivalent test performed without pH control, but the electroosmotic flow difference between the surfactant and cosolvent tests with and without pH control was minor compared to that observed with the deionized water tests. Controlling the pH was beneficial for increasing contaminant solubilization and migration from the soil region adjacent to the anode, but the high contaminant concentrations that resulted in the middle or cathode soil regions indicates that subsequent changes in the soil and/or solution chemistry caused contaminant deposition and low overall contaminant removal efficiency.     

Investigation of surfactant-enhanced mass removal and flux reduction in 3D correlated permeability fields using magnetic resonance imaging

Magnetic resonance imaging (MRI) was used to visualize the NAPL source zone architecture before and after surfactant-enhanced NAPL dissolution in three-dimensional (3D) heterogeneously packed flowcells characterized by different longitudinal correlation lengths: 2.1 cm (aquifer 1) and 1.1 cm (aquifer 2). Surfactant flowpaths were determined by imaging the breakthrough of a paramagnetic tracer (MnCl(2)) analyzed by the method of moments. In both experimental aquifers, preferential flow occurred in high permeability materials with low NAPL saturations, and NAPL was preferentially removed from the top of the aquifers with low saturation. Alternate flushing with water and two surfactant pulses (5-6 pore volumes each) resulted in approximately 63% of NAPL mass removal from both aquifers. However, overall reduction in mass flux (Mass Flux 1) exiting the flowcell was lower in aquifer 2 (68%) than in aquifer 1 (81%), and local effluent concentrations were found to increase by as high as 120 times at local sampling ports from aquifer 2 after surfactant flushing. 3D MRI images of NAPL revealed that NAPL migrated downward and created additional NAPL source zones in previously uncontaminated areas at the bottom of the aquifers. The additional NAPL source zones were created in the direction transverse to flow in aquifer 2, which explains the higher mass flux relative to aquifer 1. Analysis using a total trapping number indicates that mobilization of NAPL trapped in the two coarsest sand fractions is possible when saturation is below 0.5 and 0.4, respectively. Results from this study highlight the potential impacts of porous media heterogeneity and NAPL source zone architecture on advanced in-situ flushing technologies.     

Removal of polycyclic aromatic hydrocarbons from aged-contaminated soil using cyclodextrins: experimental study

The removal of polycyclic aromatic hydrocarbons (PAHs) from soil using water as flushing agent is relatively ineffective due to their low aqueous solubility. However, addition of cyclodextrin (CD) in washing solutions has been shown to increase the removal efficiency several times. Herein are investigated the effectiveness of cyclodextrin to remove PAH occurring in industrially aged-contaminated soil. Beta-cyclodextrin (BCD), hydroxypropyl-beta-cyclodextrin (HPCD) and methyl-beta-cyclodextrin (MCD) solutions were used for soil flushing in column test to evaluate some influent parameters that can significantly increase the removal efficiency. The process parameters chosen were CD concentration, ratio of washing solution volume to soil weight, and temperature of washing solution. These parameters were found to have a significant and almost linear effect on PAH removal from the contaminated soil, except the temperature where no significant enhancement in PAH extraction was observed for temperature range from 5 to 35 degrees C. The PAHs extraction enhancement factor compared to water was about 200.