Formation of dioxins from combustion of polyvinylidene chloride in a well-controlled incinerator

Polyvinylidene chloride (PVDC; polymer of 1,1-dichloroethylene) was combusted with paper in a well-controlled, small-scale incinerator at an average grate temperature of 700 °C, and then dioxins (PCDDs, PCDFs, and coplanar-PCBs) formed in the exhaust gases were analyzed by gas chromatography/mass spectrometry. PVDC lowered the combustion temperature due to its less flammable character. The amount of total dioxins (PCDDs + PCDFs + coplanar-PCBs) formed in the exhaust gas was 58.0 ng/g of a combustion sample and its toxicity equivalency quantity (TEQ) value was 0.64 ng-TEQ/g. The amount of PCDDs formed in the sample ranged from 2.33 ng/g (Cl₈-isomer) to 0.048 ng/g (Cl₁-isomer). The lower the number of chloride, the less production of PCDDs. On the other hand, there was no relation between the number of chloride and PCDF formation. The amount of PCDFs formed in the sample ranged from 8.02 ng/g (Cl₂-isomer) to 4.46 ng/g (Cl₈-isomer). A polyvinylchloride (PVC) sample produced 207 ng/g of total dioxins and a PVDC sample produced 57.4 ng/g of total dioxins when they were combusted under the same conditions. An approximately equal composition of dioxin isomers was formed from PVDC and PVC samples. Paper was found to contribute to PCDF formation when it was combusted with plastics.     

Hexachlorobenzene as an indicator of dioxin production from combustion

The production of polychlorinated dioxins and dibenzofurans shows a strong correlation with the production of hexachlorobenzene. Hexachlorobenzene can be used as an indicator for the production of chlorinated aromatics.     

Prediction of dioxin/furan incinerator emissions using low-molecular-weight volatile products of incomplete combustion

Emissions of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDDs/Fs) from incinerators and other stationary combustion sources are of environmental concern because of the toxicity of certain PCDD/F congeners. Measurement of trace levels of PCDDs/Fs in combustor emissions is not a trivial matter. Development of one or more simple, easy-to-measure, reliable indicators of stack PCDD/F concentrations not only would enable incinerator operators to economically optimize system performance with respect to PCDD/F emissions, but could also provide a potential technique for demonstrating compliance status on a more frequent basis. This paper focuses on one approach to empirically estimate PCDD/F emissions using easy-to-measure volatile organic C2 chlorinated alkene precursors coupled with flue gas cleaning parameters. Three data sets from pilot-scale incineration experiments were examined for correlations between C2 chlorinated alkenes and PCDDs/Fs. Each data set contained one or more C2 chloroalkenes that were able to account for a statistically significant fraction of the variance in PCDD/F emissions. Variations in the vinyl chloride concentrations were able to account for the variations in the PCDD/F concentrations strongly in two of the three data sets and weakly in one of the data sets.     

The national incinerator testing and evaluation program two-stage incinerator combustion tests

In this paper the summary results of tests conducted at the P.E.I. energy-from-waste facility, a two-stage incinerator, are presented. Extensive data on refuse feed, ash, emissions and operating conditions will provide the most significant body of information yet available for energy from waste facilities.     

A case study of dioxin monitoring in and around an industrial waste incinerator in Korea

Many studies have been conducted that monitor and trace the sources of polychlorinated dibenzo-p-dioxin/furans (PCDD/Fs) by comparing congener patterns of environmental samples with those of possible sources. In this study, we measured PCDD/F concentrations and compared congener patterns of samples of various media found in and around an industrial waste incinerator in Korea, including stack gas, fly ash, bottom ash, ambient air, soil, pine needle, and human blood. We obtained reliable data on the relationship between the PCDD/F distributions in these sources and the environment, and thus found indicators with which to assess the impact of such sources on the surrounding environment. In addition, the difference between the levels of PCDD/Fs in the blood of short-term workers and long-term workers demonstrates that these workers are exposed to the compounds produced by the indicator.     

Memory effect on the dioxin emissions from municipal waste incinerator in Taiwan

Evaluation of the dioxin removal efficiency of the air pollution control device (APCD) at an existing municipal waste incinerator (MWI) located in Taiwan is conducted via stack sampling and analysis. The MWI investigated is equipped with cyclones, dry lime scrubbing systems and fabric filters as APCDs. Results indicate that the patterns of dioxin isomers at APCDs' inlet and stack are similar. During the first year of carbon injection, the concentrations of emitted dioxin decreased greatly. The dioxin removal efficiency increased from 26.9% to 96.6% after injecting 115 kg/day activated carbon (AC). At the second year, the dioxin removal efficiency reaches 98.7% after injecting the same rate of AC continuously. The lower efficiency achieved with activated carbon injection (ACI) during the first year can be attributed to the memory effect, i.e. the dioxin or precursor desorbs slowly to the flue gas and increases the dioxin concentration at stack, resulting in a lower dioxin removal efficiency than expected.     

On the possible role of acetylene in gas-phase dioxin formation

The slow combustion of benzene/phenol gives rise to dibenzofuran (DBF) as major product of incomplete combustion, with negligible proportions of dibenzo-p-dioxin (DBD), or benzofuran (BF). Contrary to a recent proposal that acetylene growth reactions, e.g. BF-->DBF, are important in dioxin formation, co-combustion of benzene/phenol with acetylene--around 550 degrees C--did not alter this product pattern. Also, BF was identified as a product from degradation of DBF.     

Use of regenerated ferric oxide for CO destruction and suppressing dioxin formation in flue gas in a pilot-scale incinerator

Catalytic destruction of chlorinated compounds is one of the key methods in reducing pollutant emissions. For the purpose of utilizing waste materials, a catalyst was regenerated from ferric ion sludge, obtained from the addition of iron salts to precipitate heavy metals. The sludge was dewatered, heated (800 degrees C for 4 h), and ground into smaller particles. The regenerated ferric oxide particles were then used as the oxidation catalyst to destroy CO formation during the combustion of three chlorinated solvents and to suppress dioxin formation in flue gas in a real waste solvent. In the presence of catalyst, the combustion efficiency (ratio of CO(2) to the sum of CO(2) and CO) for chlorobenzene was more than 98% at 850 degrees C in a pilot-scale incinerator. The destruction and removal efficiencies of chlorobenzene, 2,4-dichlorophenol and trichlorofluoroethane were more than three nines. In the absence of catalysts, the flue gas emission from a real waste could not meet the regulatory dioxin standard of 0.1 ng-TEQ/Nm(3) even with the powdered activated carbon injection. The use of catalyst at either 100 or 300 g/h, however, was able to meet the emission standard.     

Dispersion modelling of dioxin releases from the waste incinerator at Avonmouth,Bristol, UK

A modified Gaussian atmospheric dispersion model, Industrial Source Complex (ISCST3), is used to estimate toxic equivalent ground level concentrations (GLC) of dioxins emitted from the Avonmouth municipal waste incinerator (MWI) in Bristol, UK. The sensitivity of the predicted GLC to various vapour and particle partitioning scenarios is reported. Predictions incorporating local terrain and actual emission data are used to estimate the mean incremental intake of dioxin due to MWI operation for local residents, through an existing multi-pathway human exposure model. Results are compared with predictions of incremental intake for a generalised MWI. The mean incremental dioxin intake for a hypothetical maximum exposed individual (HMEI) is shown to be up to 46.5% of the background intake compared to only 1.14% for the generalised MWI scenario. This indicates that the use of local terrain and emission data in MWI dispersion modelling is crucial for health risk assessments associated with human dioxin intake, especially in view of the current debate over the tolerable daily intake for dioxins.     

Establishing the propensity for dioxin formation using a plume temperature model for medical waste incinerator emissions in developing countries

Air pollution control devices (APCDs) are not compulsory for medical waste incinerators (MWIs) in developing countries. In South Africa, combustion gases are usually vented directly to the atmosphere at temperatures greater than the formation temperature of dioxin. The possibility of dioxin formation outside the incinerator stack has been hypothesized. A plume model has been developed and tested in the wind tunnel with a scale model of an incinerator stack. The plume temperature and trajectory predictions of the plume model were verified within a +/- 3% experimental accuracy. Using South African data, the plume model predicts that the residence time of gases in the temperature range of 150-450 degrees C in a plume is 1.3 sec on average for 5% of a year (18 days) at meteorological conditions resulting in wind speeds of less than 1 m/sec. Two published dioxin formation models were used to assess the probability of dioxin formation in the plume. The formation models predict that the average polychlorinated dibenzodioxins/furans (PCDD/Fs) formed in the plume will exceed the stack emission regulations in South Africa of 0.2 ng/Nm3 toxic equivalent quotient (TEQ) by between 2 and 40 times. The calculated concentrations do not include additional gaseous PCDD/F compounds that may be formed at high-temperature post-combustion zones through pyrosynthesis mechanisms.     

Extraction of heavy metals from MSW incinerator fly ash using saponins

An extraction process with saponins was evaluated for removing heavy metals from MSW (municipal solid waste) incinerator fly ashes. Two different fly ashes, A and B, were treated on a laboratory scale with three triterpene-glycoside type of saponins, M, Q, and T, in the pH range 4-9. The results were compared with those of the HCI and EDTA treatment. The treatment with saponins extracted 20-45% of Cr from the fly ashes. Saponins were also effective in extracting Cu from fly ash A attaining 50-60% extraction. Saponin T extracted 100% of Pb from fly ash A at pH around 4. The extraction of Zn with the saponin treatment was similar to that of the HCl treatment. Further, Cr, Cu, Pb, and Zn were fractionated by sequential extraction to investigate the effect of saponins on each fraction. Extraction behavior of other elements during the saponin treatment was also studied. The leaching test on the residues received after the saponin treatment showed that the fly ashes were successfully detoxified to meet the landfilling guideline.     

垃圾焚烧炉炉拱改造与燃烧优化的数值模拟

炉排式垃圾焚烧炉在处理比设计水分高、热值低的垃圾时,容易出现着火位置滞后、垃圾＂烧不透＂、残炭含量高等问题。采用FLIC软件的床层模型和商业软件FLUENT,对焚烧炉炉排和炉膛燃烧过程进行了模拟计算。结合某城市生活垃圾焚烧炉存在的燃烧不完全问题,通过一系列的数值实验,探索后拱高度和挡板的有无对燃烧过程的影响。比较了炉拱辐射强度、挥发分质量分数、温度沿炉排长度方向的分布以及炉膛内的速度矢量图。结果表明,降低后拱高度或增加挡板均可使着火位置有不同程度的前移;同时降低炉拱高度和增加挡板可使着火位置前移约1.1 m,提前进入稳定燃烧阶段。     

An assessment of dioxin contamination from the intermittent operation of a municipal waste incinerator in Japan and associated remediation

Significant dioxin (polychlorinated dibenzo-para-dioxins (PCDDs)/polychlorinated dibenzo-furans (PCDFs)) pollution from a municipal solid waste incinerator was discovered in 1997 in Osaka prefecture/Japan. The cause and mechanism of pollution was identified by a detailed assessment of the environment and incinerator plant. The primary sources of PCDD/PCDF pollution were high dioxin releases from an intermittently operated waste incinerator with PCDD/PCDF emissions of 150 ng-TEQ/Nm³. PCDD/PCDF also accumulated in the wet scrubber system (3,000 μg TEQ/L) by adsorption and water recirculation in the incinerator. Scrubber water was air-cooled with a cooling tower located on the roof of the incinerator. High concentrations of dioxins in the cooling water were released as aerosols into the surrounding and caused heavy soil pollution in the area near the plant. These emissions were considered as the major contamination pathway from the plant. Decontamination and soil remediation in and around the incinerator plant were conducted using a variety of destruction technologies (including incineration, photochemical degradation and GeoMelt technology). Although the soil remediation process was successfully finished in December 2006 about 3 % of the waste still remains. The case demonstrates that releases from incinerators which do not use best available technology or which are not operated according to best environmental practices can contaminate their operators and surrounding land. This significant pollution had a large impact on the Japanese government’s approach toward controlling dioxin pollution. Since this incident, a ministerial conference on dioxins has successfully strengthened control measures.     

Using stochastic risk assessment in setting information priorities for managing dioxin impact from a municipal waste incinerator

The objectives of this study were to assess site-specific carcinogenic risk of incinerator-emitted dioxins in a manner reflecting pollutant transfer across multimedia and multi-pathways. The study used site-specific environmental and exposure information and combined the Monte Carlo method with multimedia modeling to produce probability distributions of risk estimates. The risk estimates were further categorized by contaminated environmental media and exposure pathways that are experienced by human receptors in order to pinpoint significant sources of risk. Rank correlation coefficients were also calculated along with the Monte Carlo sampling to identify key factors that influenced estimation of risk. The results showed that ingestion accounted for more than 90% of the total risk and that risk control on ingestion of eggs, aboveground vegetables, and poultry should receive priority. It was also found that variation of parameters with variability accounted for around 35% of the total risk variance, while uncertainty contributed to the remaining 65%. Intake rates of aboveground vegetables, eggs, and poultry were the key parameters with the largest contribution to variance. In addition, sufficient sampling and analysis of dioxin contents in eggs, aboveground vegetables, poultry, soil, and fruit should be performed to improve risk estimation because the variation in concentrations in these media accounted for the largest overall risk variance. Finally, focus should be placed on reduction of uncertainty associated with the risk estimation through ingestion of aboveground vegetables, eggs, poultry, fruit, and soil because the risk estimates associated with these exposure pathways had the largest variance.     

Combined simulation of combustion and gas flow in a grate-type incinerator

Computational fluid dynamic (CFD) analysis of the thermal flow in the combustion chamber of a solid waste incinerator provides crucial insight into the incinerator's performance. However, the interrelation of the gas flow with the burning waste has not been adequately treated in many CFD models. A strategy for a combined simulation of the waste combustion and the gas flow in the furnace is introduced here. When coupled with CFD, a model of the waste combustion in the bed provides the inlet conditions for the gas flow field and receives the radiative heat flux onto the bed from the furnace wall and gaseous species. An unsteady one-dimensional bed model was used for the test simulation, in which the moving bed was treated as a packed bed of homogeneous fuel particles. The simulation results show the physical processes of the waste combustion and its interaction with the gas flow for various operational parameters.     

PCDD/F formation from oxy-PAH precursors in waste incinerator flyash

The yield of PCDD/F in relation to the presence of oxygenated PAH in model waste incinerator flyash has been investigated in a fixed bed laboratory scale reactor. Experiments were undertaken by thermal treatment of the model flyash at 250 and 350 °C under a simulated flue gas stream for 2 h. After reaction, the PCDD/F content of the reacted flyash and the PCDD/F released into the exhaust gas, and subsequently trapped by XAD-II resin in a down-stream condensation system were analyzed. The PAHs investigated were, dibenzofuran and benzo[b]naphtho[2,3-d]furan and were spiked onto the model flyash as reactant precursors for PCDD/F formation. The results showed significant formation of furans from both of the PAH investigated, however except from some highly chlorinated dioxin congeners, the formation of dioxins was not so common. Benzonaphthofuran was significantly more reactive than dibenzofuran in PCDD/F formation, in spite of the fact that dibenzofuran is structurally more similar to that of PCDD/F. Thus, there was no clear attribution between the chemical structure of PAH used and the formation of PCDD/F. There were considerable differences between the yields of PCDD/F congeners in the gaseous species and those in the reacted flyash under the same operational conditions. The concentration of PCDD/Fs was reduced at the higher reaction temperature of 350 °C; however, the higher temperature resulted in the majority of the PCDD/F formed on the flyash being released into the gas phase.     

PCDD/F formation from oxy-PAH precursors in waste incinerator flyash

The yield of PCDD/F in relation to the presence of oxygenated PAH in model waste incinerator flyash has been investigated in a fixed bed laboratory scale reactor. Experiments were undertaken by thermal treatment of the model flyash at 250 and 350 °C under a simulated flue gas stream for 2 h. After reaction, the PCDD/F content of the reacted flyash and the PCDD/F released into the exhaust gas, and subsequently trapped by XAD-II resin in a down-stream condensation system were analyzed. The PAHs investigated were, dibenzofuran and benzo[b]naphtho[2,3-d]furan and were spiked onto the model flyash as reactant precursors for PCDD/F formation. The results showed significant formation of furans from both of the PAH investigated, however except from some highly chlorinated dioxin congeners, the formation of dioxins was not so common. Benzonaphthofuran was significantly more reactive than dibenzofuran in PCDD/F formation, in spite of the fact that dibenzofuran is structurally more similar to that of PCDD/F. Thus, there was no clear attribution between the chemical structure of PAH used and the formation of PCDD/F. There were considerable differences between the yields of PCDD/F congeners in the gaseous species and those in the reacted flyash under the same operational conditions. The concentration of PCDD/Fs was reduced at the higher reaction temperature of 350 °C; however, the higher temperature resulted in the majority of the PCDD/F formed on the flyash being released into the gas phase.     

水泥对垃圾焚烧飞灰中重金属的固化研究

采用水泥固化法处理垃圾焚烧飞灰,研究了飞灰与水泥质量比、养护时间、添加剂和化学预处理对垃圾焚烧飞灰固化块中重金属Zn、Pb、Cu、Cd、Cr浸出的影响.结果表明,当飞灰与水泥质量比为3:4,养护时间为11d的条件下,以砂浆塑化剂为添加剂,固化块Pb、Cu、Cd和Cr的浸出浓度分别降低了72.4％、70.6％、60.0％...     

燃烧过程颗粒物的形成及我国燃烧源分析

燃料燃烧会排放一次颗粒物和二次颗粒物,一次颗粒物中亚微米粒子主要是由于无机矿物质经蒸发-成核-凝结-凝并的途径形成的;超微米颗粒的产生不同于亚微米颗粒的形成,是由于破碎机理.二次颗粒物是由气态前驱体在大气中转化而成的.我国燃烧源主要是煤燃烧、燃油机动车和农村生活燃料等.深入认识颗粒物的形成及燃烧源的特征对有效控制颗粒物的排放是很有帮助的.     

燃烧过程颗粒物的形成及我国燃烧源分析

燃料燃烧会排放一次颗粒物和二次颗粒物,一次颗粒物中亚微米粒子主要是由于无机矿物质经蒸发-成核-凝结-凝并的途径形成的;超微米颗粒的产生不同于亚微米颗粒的形成,是由于破碎机理.二次颗粒物是由气态前驱体在大气中转化而成的.我国燃烧源主要是煤燃烧、燃油机动车和农村生活燃料等.深入认识颗粒物的形成及燃烧源的特征对有效控制颗粒物的排放是很有帮助的.