前处理方法对水体总磷测定值的影响研究

研究了水样静置30 min和全部混合立即测定2种前处理方法对江苏省环太湖15条主要出入湖河流总磷测定值的影响,结果表明,采样后静置30 min测定的总磷浓度较低,仅为全部混匀立即测定总磷浓度的46%～80%;水体中漂浮水华蓝藻数量是影响2种前处理方法总磷测定结果差异性的重要因素,去除漂浮水华蓝藻较多的7条入湖河流监测数据后,静置30 min测定的总磷浓度为全部混匀立即测定总磷浓度的71%～80%。提出,基于不同的测定目的,应有针对性地选择总磷前处理方法,在水环境质量状况评估时,可参照国家标准或最新技术规定的前处理方法执行,以保证总磷浓度的可比性;在进行总磷入湖通量研究时,建议采用全部混合立即测定的前处理方法,以反映水体中实际总磷浓度;在不同国家水体总磷浓度比较时,建议采用相同的前处理方法进行总磷浓度测定。     

离子色谱法测定地表水和饮用水中亚氯酸盐、溴酸盐和氯酸盐

采用KOH梯度淋洗离子色谱法测定地表水和饮用水中ClO2-、BrO3-和ClO3-,在试验确定的条件下,3种离子与F-、Cl-、NO2-、NO3-、SO2-4、Br-、I-等7种离子分离度良好。 ClO2-、BrO3-、ClO3-在50．0μg/L～1000μg/L范围内线性良好,检出限分别为5．2μg/L、8．9μg/L、7．6μg/L,环境水样加标平行测定的RSD分别为2．1％～5．4％、4．1％～5．4％、2．5％～4．8％,两个质量浓度水平加标的平均回收率分别为93．7％～96．5％、90．3％～94．8％、98．7％～111％。     

抑制型电导-离子色谱法测定水中无机阴离子

采用抑制型电导-离子色谱法测定生活饮用水、污水和地表水中F-、Cl-、NO2-、Br-、NO3-、PO43-、SO42-等7种无机阴离子,对清洁水样过滤后直接测定,浑浊样品离心后取上清液过滤测定。F-在0.100 mg/L~1.20 mg/L范围内、其余6种阴离子在1.00 mg/L~12.0 mg/L范围内线性良好,方法检出限为0.031 mg/L~0.47 mg/L,水样平行测定的RSD为0.9%~1.8%,加标回收率为82.6%~110%。     

地表水泥沙与总磷测定值的相关性分析

为研究总磷与泥沙之间的质量浓度关系,采集了三峡库区7个断面的地表水样品,通过筛分、滤膜过滤等方式,分离了水样中不同粒径的泥沙,得到含不同泥沙质量浓度的水样,并同步分析了水样中泥沙和总磷的质量浓度.结果表明,在丰水期,总磷主要来源于泥沙中吸附的有机磷和无机磷,而溶解态磷较少.泥沙与总磷质量浓度可以用线性关系和对数关系模拟,泥沙是影响地表水中总磷测定结果的主要原因之一.     

重庆市大气TSP中水溶性无机离子的化学特征

于2001至2002年在重庆市7个采样点采集了TSP,进行了水溶性无机离子分析。结果发现,SO42-离子浓度最高,其浓度范围为6.32~20.96μg/m3;Ca2 次之,其浓度范围0.78~7.47μg/m3;SO42-、NO3-和NH4 三种离子占TSP质量的8.05%~20.96%。Ca2 、K 与SO42-和NO3-都有很好的相关性,[NO3-]/[SO42-]比值较低(均值为0.4),说明重庆市区普遍使用含硫燃煤。SO42-浓度冬季最高,主要与冬季燃煤的消耗增大有关,NO3-季节明显,与NO3-的形成环境温度密切相关。水溶性无机离子质量浓度有较明显的区域差异,中心城区采样点离子质量浓度高于距离中心城区较远的采样点。     

浅谈用离子色谱法测定水体中阴离子含量时影响阴离子分离度的因素

通过对F^-、Cl^-、NO2^-、PO4^3-、NO3^-、SO4^2-等阴离子测定条件的研究，提出阴离子之间的分离度和淋洗程度与淋洗液的比例及判峰参数的设置等有密切关系。     

浅谈离子色谱法连续对多种阴离子进行定性和定量分析

介绍了离子色谱法连续测定样品中F^-、Cl^-、NO3^-、SO4^2-8的浓度，体现了当代离子色谱的发展潮流．     

地下饮用水中痕量NO2-的催化动力学法测定

报道了一种新的测定NO2-的高选择性和高灵敏度的催化光度分析法.基于H3PO4介质中,碘绿与溴酸钾的氧化还原反应受亚硝酸盐的催化使碘绿褪色.据此建立了测定NO2-的新方法.本方法检出限为0.29μg/L,该方法用于地下饮用水、环境标样的测定,相对标准偏差为1.05%～4.80%,加标回收率为95%～117%.     

顺序注射平台-分光光度法测定水中总磷

参照希思迪在线总磷分析仪和荷兰Skalar在线过程分析仪测定水中总磷的方法,对顺序注射平台分析技术进行改进,从而建立了钼酸铵分光光度法测定水中正磷酸盐的快速分析方法,该方法集微功耗、微量试剂消耗于一体。注射平台具有模块化、投入式探头等结构特征,仪器包含3个检测量程,适用于环境监测等领域的实时在线分析。实验选择磷酸蓝的测定吸收波长为880 nm,当总磷质量浓度为0.10~2.00 mg/L时,浓度与吸光度呈线性关系,线性回归方程y=0.970 3x-0.025 3,相关系数为0.999 5,方法的检出限为1.36×10-2mg/L。     

微波消解-离子色谱法测定地表水中痕量总磷

总磷是评价河湖地表水富营养程度的重要指标,但现阶段测定总磷常用的钼酸铵分光光度法、流动注射法、电感耦合等离子体发射光谱法等灵敏度较低,不能满足地表水I类质量标准中对总磷的测定需要。为降低总磷测定方法的检出限,将环境监测实验室常用的微波消解前处理技术和离子色谱的测定方法相结合,优化微波消解和离子色谱条件,方法检出限可达0.002 mg/L,能够满足总磷质量浓度低于0.01 mg/L地表水的测定需求,同时具有较强的抗浊度和色度干扰能力,准确度和精密度较好,自动化程度高,便于推广普及。     

乌鲁木齐市可吸入颗粒物水溶性离子特征及来源解析

采暖期时在乌鲁木齐市采集了环境空气中的可吸入颗粒物,对可吸入颗粒物质量浓度及8种水溶性离子的特征和来源进行了分析。结果表明,细粒子和粗粒子的月平均质量浓度分别是53.5～233.3μg/m3和38.9～60.9μg/m3;细粒子和粗粒子中水溶性离子主要由SO24-、NH4+和NO3-组成;粗粒子中NH4+与NO3-和SO24-的相关性分别是0.70和0.66,细粒子中NH4+与NO3-和SO24-的相关性分别是0.89和0.93,铵盐是乌鲁木齐可吸入颗粒物主要存在形式;煤烟尘是乌鲁木齐市采暖期可吸入颗粒物的主要来源。     

离子色谱法测定地表水中总氮

采用碱性过硫酸钾消解水样,OnGuardⅡBa柱萃取、过滤,去除消解液中大量硫酸盐,离子色谱法测定地表水中总氮含量。试验表明,方法在0ms／L～20．0mg／L之间线性良好,相关系数r为0．9994,方法检出限为0．007mg／L。该方法与国标法同时测定标准物质,测定值均在定值范围内,6次平行测定结果的RSD分别为2．3％和1．8％,地表水样的加标回收率为95．7％～105％。实际水样的测定结果与国标法比对,无明显差异。     

水和废水中总氮的现场快速分析方法研究

在现行水中总氮分析方法的基础上,利用便携式分光光度计和密封消解管,实验了过硫酸钾氧化、硫酸联氨还原、重氮－偶联反应的最佳条件,讨论了碱性过硫酸钾溶液用量及硫酸联氨溶液用量对分析结果的影响,从而建立了水体总氮的碱性过硫酸盐消解－分光光度分析方法,该方法可在现场简便快速地测定水和废水中的总氮。     

Simultaneous extraction of bromide, chloride, fluoride and sulfate from soils, waste- and building materials

The simultaneous extraction of bromide, chloride, fluoride and sulfate was studied in soils, waste- and building materials. Acid, neutral and alkaline extractants were used; 0.01 mol l(-1) H(3)PO(4), milliQ-water and 0.01 mol l(-1) NaOH, respectively. The extracts were analysed by ion chromatography and ion selective electrode. Extracted concentrations were compared with the amount obtained by an alkaline smelt, as an approximation of the total extractable content. The results indicate that there is a significant difference in extraction behaviour between waste- and building materials and soils. Bromide and chloride were in general completely extracted from the former solid materials, but less than 10% and 50%, respectively, from soils. Fluoride is strongly bound in all investigated samples; less than 10% of the total content was extracted with any of the three extractants. The fraction of extracted sulfate varied between 4 and 87% of the total content, and was in general larger in waste- and building materials than in soils. Differences in extracted concentration between the 3 extractants occurred mainly for fluoride and sulfate. Extracted bromide was similar with all three extractants and extracted chloride showed differences for the various soil samples only. Increasing the NaOH concentration up to 1 mol l(-1) resulted mainly in an increase of extracted amount of fluoride and for soils also in extracted amounts of bromide and sulfate. Although, the results show that the composition of the solid material strongly influences the final pH of the extract and the extracted amount of investigated anions, application of Milli-Q water as an extractant might be a very fruitful option within the development of the Dutch Building Materials Decree.     

Metal immobilization and phosphorus leaching after stabilization of pyrite ash contaminated soil by phosphate amendments

In this study we would like to show the importance of a holistic approach to evaluation of chemical stabilization using phosphate amendments. An extensive evaluation of metal stabilization in contaminated soil and an evaluation of the leaching of phosphorus induced after treatment were performed. The soil was highly contaminated with Cu (2894 mg kg(-1)), Zn (3884 mg kg(-1)), As (247 mg kg(-1)), Cd (12.6 mg kg(-1)) and Pb (3154 mg kg(-1)). To immobilize the metals, mixtures of soil with phosphate (from H(3)PO(4) and hydroxyapatite (HA) with varying ratios) were prepared with a constant Pb : P molar ratio of 1: 10. The acetic acid extractable concentration of Pb in the mixture with the highest amount of added phosphoric acid (n(H(3)PO(4)) : n(HA) = 3 : 1) was reduced to 1.9% (0.62 mg L(-1)) of the extractable Pb concentration in the untreated soil, but the content of water extractable phosphorus in the samples increased from 0.04 mg L(-1) in the untreated soil sample up to 14.3 mg L(-1) in the same n(H(3)PO(4)) : n(HA) = 3 : 1 mixture. The high increase in arsenic mobility was also observed after phosphate addition. The PBET test showed phosphate induced reduction in Pb bioavailability. In attempting to stabilize Pb in the soil with the minimum treatment-induced leaching of phosphorus, it was found that a mixture of soil with phosphate addition in the molar ratio of H(3)PO(4) : HA of 0.75 : 1 showed the most promising results, with an acetic acid extractable Pb concentration of 1.35 mg L(-1) and a water extractable phosphorus concentration of 1.76 mg L(-1). The time-dependent leaching characteristics of metals and phosphorus for this mixture were evaluated by a column experiment, where irrigation of the soil mixture with the average annual amount of precipitation in Slovenia (1000 mm) was simulated. The phosphorus concentration in the leachates decreased from 2.60 mg L(-1) at the beginning of irrigation to 1.00 mg L(-1) at the end.     

氯化铵-火焰原子吸收光谱法测定地表水中的总铬

应用原子吸收法测定水样中的总铬，在不同条件下对空白样品、标准样品和实际样品进行试验分析，进一步验证了方法的准确度和精密度，加标回收率在96.8%-103%之间，相对标准偏差为2.1%。试验表明，该方法准确可靠，实际操作具有可行性，适用于工业废水和受污染地表水中总铬的测定。     

合肥市环巢湖地区种植业面源污染监测与评价

通过2016—2018年在合肥市环巢湖5个县区主要农田周边沟渠中采集水样,监测农田氮磷流失浓度,并评价该区域种植业面源污染状况.结果表明,这3年该区域种植业TN、TP流失的平均质量浓度分别为3.48 mg/L、0.602 mg/L,均高于地表水Ⅴ类水质标准.2016年与2017年TN、TP浓度差异不大,2018年较前两...     

邻菲啰啉直接光度法测定水中总铁

为了准确快速测定印染企业生产用水中的铁,探讨了Fe3＋在水浴和室温25℃时的还原反应试验,发现在这2个条件下Fe3＋均能被盐酸烃胺快速还原为Fe3＋,进而提出了测定水中总铁的新方法——邻菲哕啉直接光度法。并对该方法的检出限、显色络合物的稳定性、干扰及消除、盐酸用量、校准曲线、精密度和准确度进行了试验。检出限为0．03mg／L,显色络合物显色15min可稳定6个月,精密度RSD〈4．32％,加标回收率为95．3％～103％。通过地下水、地表水、工业废水和铁标准样品的比对实验表明,邻菲哕啉直接光度法与邻菲啰啉光度法（标准法）的测定结果无显著差异。