Parameters affecting azoxystrobin and imidacloprid degradation in biobed substrates in the North Indian tropical environment

Abstract

This study reports degradation of azoxystrobin (AZOXY) and imidacloprid (IMIDA) in the rice straw (RS)/corn cob (CC) and peat (P)/compost (C)-based biomixtures. The effect of biomixture preconditioning (10?days incubation prior to pesticide application), pesticide concentration and moisture content was evaluated. Results suggested that conditioning of biomixture greatly affected IMIDA degradation where half-life (t_1/2) was reduced by 5–9 times. This was attributed to higher microbial biomass carbon content and dehydrogenase activity in the conditioned biomixtures. Pesticide application in the conditioned biomixture did not show any negative impact on soil microbial parameters. Both pesticides degraded at faster rate in the rice straw-based biomixtures than in the corn cob-based biomixtures. Degradation slowed down with increase in initial concentration of pesticides in biomixture and 1.6–3.0 (AZOXY) and 2.4–3.6 (IMIDA) times increase in t_1/2 values was observed. The moisture content of biomixture showed positive effect on degradation which increased when moisture content was increased from 60 to 80% water holding capacity. The effect was significant for IMIDA degradation in the corn cob-based biomixtures and AZOXY degradation in the peat biomixtures. The rice straw-based biomixtures were better in degrading AZOXY and IMIDA and can be used in biopurification systems.     

Biotic and abiotic degradation of pesticide Dufulin in soils

Dufulin is a newly developed antiviral agent (or pesticide) that activates systemic acquired resistance of plants. This pesticide is widely used in China to prevent abroad viral diseases in rice, tobacco and vegetables. In this study, the potential impacts such as soil type, moisture, temperature, and other factors on Dufulin degradation in soil were investigated. Degradation of Dufulin followed the first-order kinetics. The half-life values varied from 2.27 to 150.68 days. The dissipation of Dufulin was greatly affected by soil types, with DT₅₀ (Degradation half time) varying between 17.59, 31.36, and 43.32 days for Eutric Gleysols, Cumulic Anthrosols, and Dystric Regosols, respectively. The elevated moisture accelerated the decay of Dufulin in soil. Degradation of Dufulin increased with temperature and its half-life values ranged from 16.66 to 42.79 days. Sterilization of soils and treatment with H₂O₂ resulted in a 6- and 8-fold decrease in degradation rates compared to the control, suggesting that Dufulin degradation was largely governed by microbial processes. Under different light spectra, the most effective degradation occurred with 100-W UV light (DT₅₀?=?2.27 days), followed by 15-W UV light (DT₅₀?=?8.32 days) and xenon light (DT₅₀?=?14.26 days). Analysis by liquid chromatography-mass spectroscopy (LC-MS) revealed that 2-amino-4-methylbenzothiazole was one of the major decayed products of Dufulin in soils, suggesting that elimination of diethyl phosphate and 2-fluorobenzaldehyde was most like the degradation pathway of Dufulin in Eutric Gleysols.     

Management of fresh water weeds (macrophytes) by vermicomposting using Eisenia fetida

In the present study, potential of Eisenia fetida to recycle the different types of fresh water weeds (macrophytes) used as substrate in different reactors (Azolla pinnata reactor, Trapa natans reactor, Ceratophyllum demersum reactor, free-floating macrophytes mixture reactor, and submerged macrophytes mixture reactor) during 2 months experiment is investigated. E. fetida showed significant variation in number and weight among the reactors and during the different fortnights (P <0.05) with maximum in A. pinnata reactor (number 343.3?±?10.23 %; weight 98.62?±?4.23 % ) and minimum in submerged macrophytes mixture reactor (number 105?±?5.77 %; weight 41.07?±?3.97 % ). ANOVA showed significant variation in cocoon production (F₄?=?15.67, P <0.05) and mean body weight (F₄?=?13.49, P <0.05) among different reactors whereas growth rate (F₃?=?23.62, P <0.05) and relative growth rate (F₃?=?4.91, P <0.05) exhibited significant variation during different fortnights. Reactors showed significant variation (P <0.05) in pH, Electrical conductivity (EC), Organic carbon (OC), Organic nitrogen (ON), and C/N ratio during different fortnights with increase in pH, EC, N, and K whereas decrease in OC and C/N ratio. Hierarchical cluster analysis grouped five substrates (weeds) into three clusters—poor vermicompost substrates, moderate vermicompost substrate, and excellent vermicompost substrate. Two principal components (PCs) have been identified by factor analysis with a cumulative variance of 90.43 %. PC1 accounts for 47.17 % of the total variance represents “reproduction factor” and PC2 explaining 43.26 % variance representing “growth factor.” Thus, the nature of macrophyte affects the growth and reproduction pattern of E. fetida among the different reactors, further the addition of A. pinnata in other macrophytes reactors can improve their recycling by E. fetida.     

Treatment performance and microorganism community structure of integrated vertical-flow constructed wetland plots for domestic wastewater

In order to investigate the treatment performance and microorganism mechanism of IVCW for domestic wastewater in central of China, two parallel pilot-scale IVCW systems were built to evaluate purification efficiencies, microbial community structure and enzyme activities. The results showed that mean removal efficiencies were 81.03 % for COD, 51.66 % for total nitrogen (TN), 42.50 % for NH₄ ⁺-N, and 68.01 % for TP. Significant positive correlations between nitrate reductase activities and TN and NH₄ ⁺-N removal efficiencies, along with a significant correlation between substrate enzyme activity and operation time, were observed. Redundancy analysis demonstrated gram-negative bacteria were mainly responsible for urease and phosphatase activities, and also played a major role in dehydrogenase and nitrate reductase activities. Meanwhile, anaerobic bacteria, gram-negative bacteria, and saturated FA groups, gram-positive bacteria exhibited good correlations with the removal of COD (p?=?0.388), N (p?=?0.236), and TP (p?=?0.074), respectively. The IVCW system can be used to treat domestic wastewater effectively.     

Effect of tetraconazole application on the soil microbial community

Tetraconazole is one of the most commonly used triazole fungicides in agricultural practice, and its continuous application poses a potential risk for non-target soil microorganisms. Therefore, the objective of this study was to evaluate the effect of tetraconazole at the field rate (T1, 0.33 mgkg^?1 of soil), three times the field rate (T3, 1.00 mgkg^?1 of soil) and 10 times the field rate (T10, 3.33 mgkg^?1 of soil) on the soil microorganisms. To ascertain this effect, the tetraconazole concentration and the microbial properties with potential as bioindicators of soil health (i.e. microbial biomass C, basal respiration, substrate-induced respiration, structure diversity and functional community profiling) were determined. The results showed that the degradation half-lives of tetraconazole varied from 69 to 87 days, depending on the three application concentrations. The microbial biomass C, basal respiration and substrate-induced respiration were inhibited, but they tended to recover at the end of the incubation when tetraconazole was applied at the recommended field rate. The ratios of the gram-negative to gram-positive (GN to GP) bacteria decreased, and the fungi to bacteria ratio increased after a temporal decrease on the seventh day. A principal component analysis of the PLFAs showed that tetraconazole application significantly shifted the microbial community structure on day 7. Different functional community profiles were observed, depending on the tetraconazole application rates. It was concluded that tetraconazole application decreases the soil microbial biomass and activity and changes the structures of the soil microbial community.     

Bioremediation assessment of diesel–biodiesel-contaminated soil using an alternative bioaugmentation strategy

This study investigated the effectiveness of successive bioaugmentation, conventional bioaugmentation, and biostimulation of biodegradation of B10 in soil. In addition, the structure of the soil microbial community was assessed by polymerase chain reaction-denaturing gradient gel electrophoresis. The consortium was inoculated on the initial and the 11th day of incubation for successive bioaugmentation and only on the initial day for bioaugmentation and conventional bioaugmentation. The experiment was conducted for 32 days. The microbial consortium was identified based on sequencing of 16S rRNA gene and consisted as Pseudomonas aeruginosa, Achromobacter xylosoxidans, and Ochrobactrum intermedium. Nutrient introduction (biostimulation) promoted a positive effect on microbial populations. The results indicate that the edaphic community structure and dynamics were different according to the treatments employed. CO₂ evolution demonstrated no significant difference in soil microbial activity between biostimulation and bioaugmentation treatments. The total petroleum hydrocarbon (TPH) analysis indicated a biodegradation level of 35.7 and 32.2 % for the biostimulation and successive bioaugmentation treatments, respectively. Successive bioaugmentation displayed positive effects on biodegradation, with a substantial reduction in TPH levels.     

Degradation of sulfonamides antibiotics in lake water and sediment

Degradation of three sulfonamides (SAs), namely sulfamethoxazole (SMX), sulfamethazine (SMZ), and sulfadimethoxine (SDM) in surface water and sediments collected from Taihu Lake and Dianchi Lake, China was investigated in this study. The surface water (5–10 cm) was collected from the east region of Taihu Lake, China. Two sets of degradation experiments were conducted in 3-L glass bottles containing 2 L of fresh lake water and 100 μg/L of individual SAs aerated by bubbling air at a rate of approximately 1.2 L/min, one of which was sterilized by the addition of NaN₃ (0.1 %). Sediment samples were taken from Taihu Lake and Dianchi Lake, China. For the sediment experiment, 5 g of sediment were weighed into a 50-mL glass tube, with 10 mg/kg of individual SAs. Different experimental conditions including the sediment types, sterilization, light exposure, and redox condition were also considered in the experiments. The three SAs degraded in lake water with half-lives (t _1/2) of 10.5–12.9 days, and the half-lives increased significantly to 31.9–49.8 days in the sterilized water. SMZ and SDM were degraded by abiotic processes in Taihu and Dianchi sediments, and the different experimental conditions and sediments characteristics had no significant effect on their declines. SMX, however, was mainly transformed by facultative anaerobes in Taihu and Dianchi sediments under anaerobic conditions, and the degradation rate of SMX in non-sterile sediment (t _1/2 of 9.6–16.7 days) were higher than in sterilized sediment (t _1/2 of 18.7–135.9 days). Under abiotic conditions, degradation of SMX in Dianchi sediment was faster than in Taihu sediment, probably due to the higher organic matter content and inorganic photosensitizers concentrations in Dianchi sediment. High initial SAs concentration inhibited the SAs degradation, which was likely related to the inhibition of microorganism activities by high SAs levels in sediments. Results from this study could provide information on the persistence of commonly used sulfanomides antibiotics in lake environment.     

Degradation of methylparaben in water by corona plasma coupled with ozonation

The degradation of methylparaben (MeP) in water was investigated using a pulsed corona discharge generated in oxygen, above the liquid. A comparison was made between results obtained in semi-batch corona (SBC) configuration (stationary solution, continuous gas flow) and results obtained in a semi-batch corona with recirculation combined with ozonation (SBCR?+?O₃), where the liquid is continuously circulated between a solution reservoir and the plasma reactor and the effluent gas containing ozone is bubbled through the solution in the reservoir. It was found that MeP was completely degraded after 10–15 min of treatment in both configurations. Oxidation by ozone alone, in the absence of plasma, was a slower process. The energy efficiency for MeP removal (Y _MeP) and for mineralization (Y _TOC) was significantly higher in the SBCR?+?O₃ configuration (Y _MeP?=?7.1 g/kWh at 90 % MeP removal and Y _TOC?=?0.41 g/kWh at 50 % total organic carbon (TOC) removal) than in the SBC configuration (Y _MeP?=?0.6 g/kWh at 90 % MeP removal and Y _TOC?=?0.11 g/kWh at 50 % TOC removal).     

Kinetics of phenol biodegradation at high concentration by a metabolically versatile isolated yeast Candida tropicalis PHB5

A highly tolerant phenol-degrading yeast strain PHB5 was isolated from wastewater effluent of a coke oven plant and identified as Candida tropicalis based on phylogenetic analysis. Biodegradation experiments with C. tropicalis PHB5 showed that the strain was able to utilize 99.4 % of 2,400 mg l^?1 phenol as sole source of carbon and energy within 48 h. Strain PHB5 was also observed to grow on 18 various aromatic hydrocarbons. Haldane model was used to fit the exponential growth data and the following kinetic parameters were obtained: μ _max?=?0.3407 h^?1, K _S?=?15.81 mg l^?1, K _i?=?169.0 mg l^?1 (R ²?=?0.9886). The true specific growth rate, calculated from μ _max, was 0.2113. A volumetric phenol degradation rate (V _max) was calculated by fitting the phenol consumption data with Gompertz model and specific degradation rate (q) was calculated from V _max. The q values were fitted with Haldane model, yielding following parameters: q _max?=?0.2766 g g^?1 h^?1, K _S ′?=?2.819 mg l^?1, K _i ′?=?2,093 (R ²?=?0.8176). The yield factor (Y _X/S ) varied between 0.185 to 0.96 g g^?1 for different initial phenol concentrations. Phenol degradation by the strain proceeded through a pathway involving production of intermediates such as catechol and cis,cis-muconic acid which were identified by enzymatic assays and HPLC analysis.     

Sorption of selected pesticides on soils,sediment and straw from a constructed agricultural drainage ditch or pond

Buffer zones such as ponds and ditches are used to reduce field-scale losses of pesticides from subsurface drainage waters to surface waters. The objective of this study was to assess the efficiency of these buffer zones, in particular constructed wetlands, focusing specifically on sorption processes. We modelled the sorption processes of three herbicides [2-methyl-4-chlorophenoxyacetic acid (2,4-MCPA), isoproturon and napropamide] and three fungicides (boscalid, prochloraz and tebuconazole) on four substrates (two soils, sediment and straw) commonly found in a pond and ditch in Lorraine (France). A wide range of Freundlich coefficient (K _fads) values was obtained, from 0.74 to 442.63 mg^1???n ?L ⁿ ?kg^?1, and the corresponding K _foc values ranged from 56 to 3,725 mg^1???n ?L ⁿ ?kg^?1. Based on potential retention, the substrates may be classified as straw >> sediments > soils. These results show the importance of organic carbon content and nature in the process of sorption. Similarly, the studied pesticides could be classified according to their adsorption capacity as follows: prochloraz >> tebuconazole–boscalid > napropamide >> MCPA–isoproturon. This classification is strongly influenced by the physico-chemical properties of pesticides, especially solubility and K _oc. Straw exhibited the largest quantity of non-desorbable pesticide residues, from 12.1 to 224.2 mg/L for all pesticides. The presence of plants could increase soil–sediment sorption capacity. Thus, establishment and maintenance of plants and straw filters should be promoted to optimise sorption processes and the efficiency of ponds and ditches in reducing surface water pollution.     

Inhibition of residual <Emphasis Type="Italic">n</Emphasis>-hexane in anaerobic digestion of lipid-extracted microalgal wastes and microbial community shift

Converting lipid-extracted microalgal wastes to methane (CH₄) via anaerobic digestion (AD) has the potential to make microalgae-based biodiesel platform more sustainable. However, it is apparent that remaining n-hexane (C₆H₁₄) from lipid extraction could inhibit metabolic pathway of methanogens. To test an inhibitory influence of residual n-hexane, this study conducted a series of batch AD by mixing lipid-extracted Chlorella vulgaris with a wide range of n-hexane concentration (～10 g chemical oxygen demand (COD)/L). Experimental results show that the inhibition of n-hexane on CH₄ yield was negligible up to 2 g COD/L and inhibition to methanogenesis became significant when it was higher than 4 g COD/L based on quantitative mass balance. Inhibition threshold was about 4 g COD/L of n-hexane. Analytical result of microbial community profile revealed that dominance of alkane-degrading sulfate-reducing bacteria (SRB) and syntrophic bacteria increased, while that of methanogens sharply dropped as n-hexane concentration increased. These findings offer a useful guideline of threshold n-hexane concentration and microbial community shift for the AD of lipid-extracted microalgal wastes.     

Polar organic chemical integrative sampler (POCIS) uptake rates for 17 polar pesticides and degradation products: laboratory calibration

Polar organic chemical integrative samplers (POCIS) are useful for monitoring a wide range of chemicals, including polar pesticides, in water bodies. However, few calibration data are available, which limits the use of these samplers for time-weighted average concentration measurements in an aquatic medium. This work deals with the laboratory calibration of the pharmaceutical configuration of a polar organic chemical integrative sampler (pharm-POCIS) for calculating the sampling rates of 17 polar pesticides (1.15?≤?logK _ow?≤?3.71) commonly found in water. The experiment, conducted for 21 days in a continuous water flow-through exposure system, showed an integrative accumulation of all studied pesticides for 15 days. Three compounds (metalaxyl, azoxystrobine, and terbuthylazine) remained integrative for the 21-day experiment. The sampling rates measured ranged from 67.9 to 279 mL?day^?1 and increased with the hydrophobicity of the pesticides until reaching a plateau where no significant variation in sampling rate is observed when increasing the hydrophobicity.     

Evaluation of the ecotoxicological impact of the organochlorine chlordecone on soil microbial community structure,abundance, and function

The insecticide chlordecone applied for decades in banana plantations currently contaminates 20,000 ha of arable land in the French West Indies. Although the impact of various pesticides on soil microorganisms has been studied, chlordecone toxicity to the soil microbial community has never been assessed. We investigated in two different soils (sandy loam and silty loam) exposed to different concentrations of CLD (D0, control; D1 and D10, 1 and 10 times the agronomical dose) over different periods of time (3, 7, and 32 days): (i) the fate of chlordecone by measuring ¹⁴C-chlordecone mass balance and (ii) the impact of chlordecone on microbial community structure, abundance, and function, using standardized methods (-A-RISA, taxon-specific quantitative PCR (qPCR), and ¹⁴C-compounds mineralizing activity). Mineralization of ¹⁴C-chlordecone was inferior below 1 % of initial ¹⁴C-activity. Less than 2 % of ¹⁴C-activity was retrieved from the water-soluble fraction, while most of it remained in the organic-solvent-extractable fraction (75 % of initial ¹⁴C-activity). Only 23 % of the remaining ¹⁴C-activity was measured in nonextractable fraction. The fate of chlordecone significantly differed between the two soils. The soluble and nonextractable fractions were significantly higher in sandy loam soil than in silty loam soil. All the measured microbiological parameters allowed discriminating statistically the two soils and showed a variation over time. The genetic structure of the bacterial community remained insensitive to chlordecone exposure in silty loam soil. In response to chlordecone exposure, the abundance of Gram-negative bacterial groups (β-, γ-Proteobacteria, Planctomycetes, and Bacteroidetes) was significantly modified only in sandy loam soil. The mineralization of ¹⁴C-sodium acetate and ¹⁴C-2,4-d was insensitive to chlordecone exposure in silty loam soil. However, mineralization of ¹⁴C-sodium acetate was significantly reduced in soil microcosms of sandy loam soil exposed to chlordecone as compared to the control (D0). These data show that chlordecone exposure induced changes in microbial community taxonomic composition and function in one of the two soils, suggesting microbial toxicity of this organochlorine.     

Biomass smoke in Burkina Faso: what is the relationship between particulate matter,carbon monoxide,and kitchen characteristics?

In Burkina Faso where cooking with biomass is very common, little information exists regarding kitchen characteristics and their impact on air pollutant levels. The measurement of air pollutants such as respirable particulate matter (PM₁₀), an important component of biomass smoke that has been linked to adverse health outcomes, can also pose challenges in terms of cost and the type of equipment needed. Carbon monoxide could potentially be a more economical and simpler measure of air pollution. The focus of this study was to first assess the association of kitchen characteristics with measured PM₁₀ and CO levels and second, the relationship of PM₁₀ with CO concentrations, across these different kitchen characteristics in households in Nouna, Burkina Faso. Twenty-four-hour concentrations of PM₁₀ (area) were measured with portable monitors and CO (area and personal) estimated using color dosimeter tubes. Data on kitchen characteristics were collected through surveys. Most households used both wood and charcoal burned in three-stone and charcoal stoves. Mean outdoor kitchen PM₁₀ levels were relatively high (774 μg/m³, 95 % CI 329–1,218 μg/m³), but lower than indoor concentrations (Satterthwaite t value, ?6.14; p?<?0.0001). In multivariable analyses, outdoor kitchens were negatively associated with PM₁₀ (OR?=?0.06, 95 % CI 0.02–0.16, p value <0.0001) and CO (OR?=?0.03, 95 % CI 0.01–0.11, p value <0.0001) concentrations. Strong area PM₁₀ and area CO correlations were found with indoor kitchens (Spearman’s r?=?0.82, p?<?0.0001), indoor stove use (Spearman’s r?=?0.82, p?<?0.0001), and the presence of a smoker in the household (Spearman’s r?=?0.83, p?<?0.0001). Weak correlations between area PM₁₀ and personal CO levels were observed with three-stone (Spearman’s r?=?0.23, p?=?0.008) and improved stoves (Spearman’s r?=?0.34, p?=?0.003). This indicates that the extensive use of biomass fuels and multiple stove types for cooking still produce relatively high levels of exposure, even outdoors, suggesting that both fuel subsidies and stove improvement programs are likely necessary to address this problem. These findings also indicate that area CO color dosimeter tubes could be a useful measure of area PM₁₀ concentrations when levels are influenced by strong emission sources or when used in indoors. The weaker correlation observed between area PM₁₀ and personal CO levels suggests that area exposures are not as useful as proxies for personal exposures, which can vary widely from those recorded by stationary monitors.     

Heterogeneous photocatalytic oxidation of cyprodinil and fludioxonil in leaching water under solar irradiation

The efficiency of ZnO and TiO₂ suspensions in the photocatalytic degradation of two fungicides (cyprodinil and fludioxonil) in leaching water was investigated. The experiments were carried out at pilot plant scale using compound parabolic collectors under natural sunlight. The blank experiments for both irradiated compounds solutions showed that both oxides strongly enhanced the removal of the fungicides. The addition of an oxidant (Na₂S₂O₈) to the ZnO or TiO₂ increased the rate of photooxidation. The degradation of cyprodinil and fludioxonil followed first order kinetics according to the Langmuir-Hinshelwood model. Complete degradation of both fungicides was achieved within 4 h (t_30W = 18 min) when treated with illuminated ZnO. The disappearance time (DT₇₅), when referred to the normalized illumination time (t_30W), was lower than 40 and 550 min (t_30W = 2 and 40 min) for both fungicides using ZnO or TiO₂, respectively. ZnO appeared to be more effective in cyprodinil and fludioxonil oxidation than TiO₂ probably due to its nonstoichiometry.     

Survival of Escherichia coli O157:H7 in soils under different land use types

Laboratory studies on Escherichia coli O157:H7 survival in soils from four different land use types: forest, tea plantation, bamboo grove, and vegetable garden were investigated at 25?±?1 °C with the field capacity (soil water content at ?33 kPa). Results showed that E. coli O157:H7 declined quickly in the test soils, but its survival dynamics varied in the soils under different land use types. The survival time needed to reach the detection limit (t _d) in the test soils ranged from 2.1 to 3.6 days, with slightly longer t _d values being observed in soils from the bamboo grove. Stepwise multiple regression analysis revealed that the t _d values were shorter in sandy, lower pH, and lower organic carbon content soils. Different E. coli O157:H7 survival time in the soils under different land uses suggests that it is important to adapt proper management practices for reducing the potential risks of pathogen contamination when diary manure is applied to agricultural land.     

Comparing the sensitivity of soil invertebrates to pesticides with that of Eisenia fetida

The sole routine testing of the standard earthworm Eisenia fetida for the terrestrial risk assessment of pesticides has been under much debate since other soil invertebrates may be more sensitive than this standard test species. However, the very low availability of laboratory toxicity data for taxa other than E. fetida has greatly hampered sensitivity comparisons. In the present study, the relative tolerance (T_rel) approach was used to enable comparing toxicity thresholds obtained from the US-EPA ECOTOX database, for main terrestrial taxonomic groups and pesticidal types of action (insecticides, fungicides, herbicides, and other) separately. Analyses confirmed previously reported lower and higher sensitivity of collembolans to fungicides and insecticides, respectively. However, various other discrepancies in susceptibility relative to E. fetida were encountered as indicated by species sensitivity distributions and/or calculated 95% confidence intervals of T_rel values. Arachnids and isopods were found to be more sensitive to insecticides, and nematodes to fungicides, as compared to E. fetida. Implications of study findings for the terrestrial risk assessment of pesticides are discussed.     

Synergic degradation of diesel by Scirpus triqueter and its endophytic bacteria

The endophytic bacterium isolated from Scirpus triqueter was proved to be an oil-degraded bacterium. A pot experiment was conducted to investigate the removal ratio of diesel under the combined effect of oil-degraded microorganism (Pseudomonas sp. J4AJ) and S. triqueter. The effect of diesel on plant growth parameters, soil enzymes and microbial community was assessed after 60 days. The results showed that the soils which were planted with S. triqueter and inoculated with J4AJ displayed the highest removal ratio (54.51?±?0.15 %) after 60-day experiment. However, the removal ratio of J4AJ-treated soils was 38.97?±?0.55 %. Diesel was toxic to S. triqueter, as evidenced by growth inhibition during the experimental period. However, the plant height and stem biomass in the soils inoculated with J4AJ significantly increased. The combined effect of S. triqueter and J4AJ improved the enzyme activities of the catalase and dehydrogenase in the contaminated soil. The diversity index in soils under the effect of S. triqueter combined with J4AJ was lower than that of the other soil samples. The principal analysis of phospholipid fatty acid signatures revealed that the combined effect of S. triqueter and J4AJ increased the differences of soil microbial community structure with the other treatments.     

Influence of short-time imidacloprid and acetamiprid application on soil microbial metabolic activity and enzymatic activity

The influence of two neonicotinoids, i.e., imidacloprid (IMI) and acetamiprid (ACE), on soil microbial activities was investigated in a short period of time using a combination of the microcalorimetric approach and enzyme tests. Thermodynamic parameters such as Q _T (J g^?1 soil), ?H _met (kJ mol^?1), J _Q/S (J g^?1 h^?1), k (h^?1), and soil enzymatic activities, dehydrogenase, phosphomonoesterase, arginine deaminase, and urease, were used to evaluate whole metabolic activity changes and acute toxicity following IMI and ACE treatment. Various profiles of thermogenic curves reflect different soil microbial activities. The microbial growth rate constant k, total heat evolution Q _T (expect for IMI), and inhibitory ratio I show linear relationship with the doses of IMI and ACE. Q _T for IMI increases at 0.0–20 μg g^?1 and then decreases at 20–80 μg g^?1, possibly attributing to the presence of tolerant microorganisms. The 50 % inhibitory ratios (IC₅₀) of IMI and ACE are 95.7 and 77.2 μg g^?1, respectively. ACE displays slightly higher toxicity than IMI. Plots of k and Q _T against microbial biomass-C indicate that the k and Q _T are growth yield-dependent. IMI and ACE show 29.6; 40.4 and 23.0; and 23.3, 21.7, and 30.5 % inhibition of dehydrogenase, phosphomonoesterase, and urease activity, respectively. By contrast, the arginine deaminase activity is enhanced by 15.2 and 13.2 % with IMI and ACE, respectively. The parametric indices selected give a quantitative dose-response relationship of both insecticides and indicate that ACE is more toxic than IMI due to their difference in molecular structures.     

The use of artificial neural network (ANN) for the prediction and simulation of oil degradation in wastewater by AOP

The application of advanced oxidation process (AOP) in the treatment of wastewater contaminated with oil was investigated in this study. The AOP investigated is the homogeneous photo-Fenton (UV/H₂O₂/Fe⁺²) process. The reaction is influenced by the input concentration of hydrogen peroxide H₂O₂, amount of the iron catalyst Fe⁺², pH, temperature, irradiation time, and concentration of oil in the wastewater. The removal efficiency for the used system at the optimal operational parameters (H₂O₂?=?400 mg/L, Fe⁺²?=?40 mg/L, pH?=?3, irradiation time?=?150 min, and temperature?=?30 °C) for 1,000 mg/L oil load was found to be 72 %. The study examined the implementation of artificial neural network (ANN) for the prediction and simulation of oil degradation in aqueous solution by photo-Fenton process. The multilayered feed-forward networks were trained by using a backpropagation algorithm; a three-layer network with 22 neurons in the hidden layer gave optimal results. The results show that the ANN model can predict the experimental results with high correlation coefficient (R ²?=?0.9949). The sensitivity analysis showed that all studied variables (H₂O₂, Fe⁺², pH, irradiation time, temperature, and oil concentration) have strong effect on the oil degradation. The pH was found to be the most influential parameter with relative importance of 20.6 %.