Formation of polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDD/Fs) from a refinery process for zinc oxide used in feed additives: a source of dioxin contamination in Chilean pork

The Republic of Korea found dioxin at concentrations exceeding the Korean maximum residue limit (MRL) in pork (2 pg TEQ g⁻¹ fat) imported from Chile in June 2008. Korea and Chile collaborated and investigated to find out the sources of contamination. An isotope dilution method and high resolution gas chromatography/mass spectrometry (HR-GC/MS) were used for the analysis of PCDD/Fs. PCDD/Fs were found from 2.17 to 36.7 pg TEQ g⁻¹ fat from Chilean pork. 2,3,4,7,8-PeCDF, 1,2,3,4,7,8-HxCDF, 1,2,3,6,7,8-HxCDF, and 2,3,4,6,7,8-HxCDF were found as the major congeners in pork samples. 2,3,4,7,8-PeCDF showed the highest concentration and contributed about 30% among the congeners in most of the samples. 2,3,7,8-TCDD, 1,2,3,7,8,9-HxCDD, OCDD, 2,3,7,8-TCDF, 1,2,3,7,8-PeCDF, 1,2,3,7,8,9-HxCDF, and OCDF were not detected or exist at background levels in the less contaminated samples. Remarkably high concentrations of PCDD/Fs were found in samples of zinc oxide (17 147 pg TEQ g⁻¹), zinc oxide based premix (6673 pg TEQ g⁻¹), and the residue crust (800 pg TEQ g⁻¹) in a mixing chamber in the feed mill. From the results of various investigations, this case concluded that zinc oxide in the feed was the major source of the dioxin contamination in pork. The dioxins were formed from a metal refinery process to collect zinc oxide.     

An assessment of dioxin contamination from the intermittent operation of a municipal waste incinerator in Japan and associated remediation

Significant dioxin (polychlorinated dibenzo-para-dioxins (PCDDs)/polychlorinated dibenzo-furans (PCDFs)) pollution from a municipal solid waste incinerator was discovered in 1997 in Osaka prefecture/Japan. The cause and mechanism of pollution was identified by a detailed assessment of the environment and incinerator plant. The primary sources of PCDD/PCDF pollution were high dioxin releases from an intermittently operated waste incinerator with PCDD/PCDF emissions of 150 ng-TEQ/Nm³. PCDD/PCDF also accumulated in the wet scrubber system (3,000 μg TEQ/L) by adsorption and water recirculation in the incinerator. Scrubber water was air-cooled with a cooling tower located on the roof of the incinerator. High concentrations of dioxins in the cooling water were released as aerosols into the surrounding and caused heavy soil pollution in the area near the plant. These emissions were considered as the major contamination pathway from the plant. Decontamination and soil remediation in and around the incinerator plant were conducted using a variety of destruction technologies (including incineration, photochemical degradation and GeoMelt technology). Although the soil remediation process was successfully finished in December 2006 about 3 % of the waste still remains. The case demonstrates that releases from incinerators which do not use best available technology or which are not operated according to best environmental practices can contaminate their operators and surrounding land. This significant pollution had a large impact on the Japanese government’s approach toward controlling dioxin pollution. Since this incident, a ministerial conference on dioxins has successfully strengthened control measures.     

Multi-criteria assessment of the viability of valorising vegetable by-products from the distribution as secondary raw material for animal feed

Environmental Science and Pollution Research - Approximately 33% of food produced around the world is wasted. In the distribution sector, erroneous orders or demand predictions result in products...     

The reduction of dioxin emissions from the processes of heat and power generation

The first reports that it is possible to emit dioxins from the heat and power generation sector are from the beginning of the 1980s. Detailed research proved that the emission of dioxins might occur during combustion of hard coal, brown coal, and furnace oil as well as coke-oven gas. The emission of dioxins occurs in wood incineration; wood that is clean and understood as biomass; or, in particular, wood waste (polluted). This paper thoroughly discusses the mechanism of dioxin formation in thermal processes, first and foremost in combustion processes. The parameters influencing the quantity of dioxins formed and the dependence of their quantity on the conditions of combustion are highlighted. Furthermore, the methods of reducing dioxin emissions from combustion processes (primary and secondary) are discussed. The most efficacious methods that may find application in the heat and power generation sector are proposed; this is relevant from the point of view of the implementation of the Stockholm Convention resolutions in Poland with regard to persistent organic pollutants.     

Lime as the source of PCDD/F contamination in citrus pulp pellets from Brazil and status of the monitoring program

After an exhaustive investigation, in 1997 the source of the milk contamination in Germany was traced to citrus pulp pellets originating from Brazil. It has been shown that lime was the source of the PCDD/F contamination of these products. After this conclusion, a continuous monitoring program has been performed over a two year period and the results are presented in this paper. Standard isotope dilution techniques were used for all samples, which were analyzed by selected ion monitoring high resolution GC–MS.     

Assessment of the effluent quality from a gold mining industry in Ghana

The physical and chemical qualities of the process effluent and the tailings dam wastewater of AngloGold-Ashanti Limited, a gold mining company in Ghana, were studied from June to September, 2010. The process effluent from the gold extraction plant contains high amounts of suspended solids and is therefore highly turbid. Arsenic, copper and cyanide were identified as the major pollutants in the process effluent with average concentrations of 10.0, 3.1 and 21.6 mg?L^?1, respectively. Arsenic, copper, iron and free cyanide (CN^?) concentrations in the process effluent exceeded the Ghana EPA discharge limits; therefore, it is necessary to treat the process effluent before it can be discharged into the environment. Principal component analysis of the data indicated that the process effluent characteristics were influenced by the gold extraction process as well as the nature of the gold-bearing ore processed. No significant correlation was observed between the wastewater characteristics themselves, except for the dissolved oxygen and the biochemical oxygen demand. The process effluent is fed to the Sansu tailings dam, which removes 99.9 % of the total suspended solids and 99.7 % of the turbidity; but copper, arsenic and cyanide concentrations were still high. The effluent produced can be classified as inorganic with a high load of non-biodegradable compounds. It was noted that, though the Sansu tailings dam stores the polluted effluent from the gold extraction plant, there will still be serious environmental problems in the event of failure of the dam.     

Radon as a naturally occurring tracer for the assessment of residual NAPL contamination of aquifers

The noble gas radon has a strong affinity to non-aqueous phase-liquids (NAPLs). That property makes it applicable as naturally occurring partitioning tracer for assessing residual NAPL contamination of aquifers. In a NAPL contaminated aquifer, radon dissolved in the groundwater partitions preferably into the NAPL. The magnitude of the resulting radon deficit in the groundwater depends on the NAPL-specific radon partition coefficient and on the NAPL saturation of the pore space. Hence, if the partition coefficient is known, the NAPL saturation is attainable by determination of the radon deficit. After a concise discussion of theoretical aspects regarding radon partitioning into NAPL, related experimental data and results of a field investigation are presented. Aim of the laboratory experiments was the determination of radon partition coefficients of multi-component NAPLs of environmental concern. The on-site activities were carried out in order to confirm the applicability of the "radon method" under field conditions.     

Feeding trial on rainbow trout: comparison of dry fish feed and Baltic herring as a source of PCDD/Fs and PCBs

Fish is an important source of dietary intake of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and polychlorinated biphenyls (PCBs). To assess bioaccumulation of PCDD/Fs and PCBs in farm-raised fish, rainbow trout were fed with either Baltic herring or dry fish feed. Baltic herring feed had a PCDD/F sum concentration of 125 ng kg(-1) dry weight (d.w.), and dry fish feed contained 18.2 ng kg(-1) d.w. of PCDD/Fs. The PCB concentrations of Baltic herring and dry fish feed were 188 and 48.7 microg kg(-1) d.w., respectively. After feeding with Baltic herring for 4 months, the PCDD/F concentration of the rainbow trout fillet was 27.3 ng kg(-1) fresh weight (f.w.), which was 7.0-fold higher than the initial concentration. The PCDD/F concentration and congener profile in rainbow trout had become almost the same as in Baltic herring. PCDD/Fs were accumulated in the fillet with an efficiency of 21%. Feeding of rainbow trout with dry fish feed resulted in a PCDD/F concentration of 8.08 ng kg(-1) f.w., denoting a 2.1-fold increase from the initial level. The accumulation efficiency was 29%. Time trends in PCB concentrations followed those of PCDD/Fs. After 4 months, the PCB sum concentration in herring-fed rainbow trout was 94.4 pg kg(-1) f.w., whereas in dry fish feed-fed rainbow trout it was 38.6 microg kg(-1) f.w. Accumulation efficiencies of PCBs were higher than those of PCDD/Fs. Based on the accumulated PCDD/F and PCB concentrations, it was estimated that frequent consumption of rainbow trout fed with Baltic herring could lead to a human daily intake that exceeds the recommendation of WHO.     

Life cycle of PCBs and contamination of the environment and of food products from animal origin

This report gives a summary of the historic use, former management and current release of polychlorinated biphenyls (PCBs) in Germany and assesses the impact of the life cycle of PCBs on the contamination of the environment and of food products of animal origin. In Germany 60,000 t of PCBs were used in transformers, capacitors or as hydraulic oils. The use of PCB oils in these “closed applications”, has been banned in Germany in 2000. Thirty to 50% of these PCBs were not appropriately managed. In West Germany, 24,000 t of PCBs were used in open applications, mainly as additive (plasticiser, flame retardant) in sealants and paints in buildings and other construction. The continued use in open applications has not been banned, and in 2013, an estimated more than 12,000 t of PCBs were still present in buildings and other constructions. These open PCB applications continuously emit PCBs into the environment with an estimated release of 7–12 t per year. This amount is in agreement with deposition measurements (estimated to 18 t) and emission estimates for Switzerland. The atmospheric PCB releases still have an relevant impact on vegetation and livestock feed. In addition, PCBs in open applications on farms are still a sources of contamination for farmed animals. Furthermore, the historic production, use, recycling and disposal of PCBs have contaminated soils along the lifecycle. This legacy of contaminated soils and contaminated feed, individually or collectively, can lead to exceedance of maximum levels in food products from animals. In beef and chicken, soil levels of 5 ng PCB-TEQ/kg and for chicken with high soil exposure even 2 ng PCB-TEQ/kg can lead to exceedance of EU limits in meat and eggs. Areas at and around industries having produced or used or managed PCBs, or facilities and areas where PCBs were disposed need to be assessed in respect to potential contamination of food-producing animals. For a large share of impacted land, management measures applicable on farm level might be sufficient to continue with food production. Open PCB applications need to be inventoried and better managed. Other persistent and toxic chemicals used as alternatives to PCBs, e.g. short chain chlorinated paraffins (SCCPs), should be assessed in the life cycle for exposure of food-producing animals and humans.     

Distribution and ecological risk assessment of organochlorine pesticides in surface sediments from the East Lake,China

Organochlorine pesticides (OCPs) are ubiquitous pollutants, and their presence in urban lakes is a concern for human and ecological health. Surface sediments in the East Lake, China, were collected in winter 2012 and summer 2013 to investigate concentrations, distribution patterns, possible sources, and potential ecological risks of OCPs in this area. The total concentrations of 14 OCPs ranged from 6.3 to 400 ng g^?1 dry weight (dw) with an average concentration of 79 ng g^?1 dw. The mean values of hexachlorocyclohexanes (HCHs) (α-, β-, γ-, and δ-HCH) and dichlorodiphenyltrichloroethanes (DDTs) (p,p’-DDE, p,p’-DDD, and p,p’-DDT) were 36 and 7.6 ng g^?1 dw, accounting for 45 and 10 % of the total OCPs, respectively. The concentrations of OCPs in sediment samples collected in winter were significantly higher than those in summer, especially the HCHs, of which in winter were two times greater than summer. Composition analyses indicated that DDTs and endosulfan were mainly from historical contribution. Historical use of technical HCH and new input of lindane were probably the source of HCHs in the East Lake. Most sampling sites of HCHs and DDTs were found to have the potential ecological risk based on levels specified in the sediment quality standards.     

Exposure to polychlorinated biphenyls in residents near a chemical factory in Italy: the food chain as main source of contamination

High levels of PCBs were recently found in soil, food and some farmers living close to a chemical factory which until the 1980s had produced polychlorinated biphenyls (PCBs) in Brescia, North Italy. We performed a survey on a random sample of subjects aged 20-79 years living in various areas of the town with different levels of soil pollution to investigate factors associated with increased levels of PCB in serum (24 congeners were tested). Total PCB values were closely related to age (Spearman r=0.68; p<0.0001). The 166 consumers of locally produced food had higher PCB levels than non-consumers (median=1143 versus 719; 95th centile=9301 versus 2635ng/g lipid) with the highest levels among consumers of food produced in the most contaminated area close to the factory (median=2551; 95th centile=33464ng/g lipid). A dose-effect relationship between consumption of food produced in this area and PCB blood levels was observed (Spearman r=0.52, p=0.0014). Consumers of only plant food produced in this area had higher levels of PCB than non-consumers (median=1100; 95th centile=10,800ng/g lipid). Three subjects who had worked at the factory in the past showed high PCB levels. Distribution of PCB congeners did not differ between consumers of locally produced food and non-consumers, apart from PCB 209 which was found at high levels in former factory workers and was more common among consumers of food produced in the polluted area. In conclusion, we found high serum PCB levels in humans living in a highly polluted area in an industrialized town in Italy, due mainly to consumption of food produced in polluted areas.     

Mercury deposition/accumulation rates in the vicinity of a lead smelter as recorded by a peat deposit

Mercury (Hg) concentration profiles and historical accumulation rates were determined in three ²¹⁰Pb-dated cores from a peat deposit in the vicinity of a lead (Pb) smelter at Příbram, Czech Republic. The Hg concentrations in peat samples ranged from 66 to 701 μg kg⁻¹. Cumulative Hg inventories from each core (for the past 150 yr) varied by a factor of 1.4 (13.6–18.5 mg Hg m⁻²), indicating variations of net Hg accumulation rate within the peat deposit. Historical changes in vegetation cover (leading to variable interception by trees) are probably responsible for this variation in space and time. The uncorrected Hg accumulation rates peaked between the 1960s and 1980s (up to 226 μg m⁻² yr⁻¹). Recent findings show that Hg records from peat tend to overestimate historical levels of Hg deposition. Therefore we used the mass loss compensation factor (MLCF) to normalize Hg accumulation rates. These corrected Hg accumulation rates were significantly lower (maximum 129 μg m⁻² yr⁻¹) and better corresponded to changes in historical smelter emissions, which were highest in the 1960s. The agreement between the corrected Hg accumulation rates in the uppermost peat sections (2–38 μg m⁻² yr⁻¹) and biomonitoring of atmospheric deposition by mosses in several recent years (4.7–34.4 μg m⁻² yr⁻¹) shows the usefulness of MLCF application on Hg accumulation in peat archives. However, the MLCF correction was unsuitable for Pb. The recent Pb deposition rates obtained by an independent biomonitoring study using mosses (0.5–127 mg m⁻² yr⁻¹) were better correlated with net Pb accumulation rates recorded in peat (7–145 mg m⁻² yr⁻¹) than with corrected rates obtained by the MLCF approach (1–28 mg m⁻² yr⁻¹).     

Conifer needles as passive biomonitors of the spatial and temporal distribution of DDT from a point source

Needles of two conifer species, Picea abies and Pinus nigra, were used as passive samplers for monitoring air contamination by sampling at increasing distances from a suspected point source of DDT. Needle concentrations declined with increasing distance downwind of the point source allowing to identify spatial and temporal trends of accumulation. This suggested that conifer needles are effective biomonitors of contamination levels in areas characterized by the presence of semi-volatile substances. Differences in uptake were apparent between the species. Needle morphology and structure were studied with scanning electron microscope (SEM) as were dimensional parameters (surface area, volume). The results suggest that the concentrations depend on a mechanism involving the inner structure of the needles, specifically the number and accessibility of resin channels rather than their surface area. Pine needles have more channels with greater accessibility than spruce. The results suggest that spruce is more suitable for short term measurement while pine for determining long term cumulative exposure.     

Wastewater treatment plants (WWTPs) as a source of sediment contamination by toxic organic pollutants and fecal sterols in a semi-enclosed bay in Korea

Toxic organic contaminants and a macrobenthic community were assayed in sediments collected near a wastewater treatment plant (WWTP) outfall to assess the impact of WWTP discharges on an aquatic environment. Average concentrations of toxic organic contaminants in sediments from 20 locations were 96.7ng TEQ/kg dry matter for PCDD/Fs, 1.84ng TEQ/kg dry matter for dioxin-like PCBs, 29.1microg/kg dry matter for PBDEs, 411microg/kg dry matter for nonylphenols, 1021microg/kg dry matter for fecal sterols, and 928microg/kg dry matter for PAHs. Concentrations of all the organic contaminants and fecal sterols varied widely and there was a clear decrease in concentration gradients with increasing distances from the WWTP outfall. This result suggests that WWTP activities contribute to contamination by organic chemicals. A survey of benthic organisms showed the dominance of a few polychaete species, indicating a deterioration of the macrobenthic community by the WWTP discharge. Non-parametric multidimensional scaling (MDS) ordination and Spearman correlation analyses showed that organic contamination is associated with the benthic community structure. For polychaete species, the sensitive species for organic contaminants was Paraprionospio pinnata, while contaminant-tolerant species were Spiochaetopterus koreana and Capitella capitata. BIOENV analyses of all locations suggested PCDDs and PCDFs as the major contaminants influencing the structure of the macrobenthic community. The present study highlights that continuous WWTP discharges contribute to severe organic contamination and risks for the benthic community in an aquatic ecosystem.     

Tissue distribution of organochlorine pesticides in fish collected from the Pearl River Delta, China: implications for fishery input source and bioaccumulation

Fish tissues from different fishery types (freshwater farmed, seawater farmed and seawater wild) were analyzed for organochlorine pesticides (OCPs), with the aim to further our understanding of bioaccumulation, and reflect the state of different fishery environments. Significantly higher SigmaOCP levels were found in seawater farmed fish than others, and among three freshwater farmed species, the lowest levels occurred in filter-feeding fish (bighead carp). Liver contained the highest SigmaOCP levels, while no significant differences were found among other tissues. Among DDT components, p,p'-DDT was abundant in seawater fish, while for freshwater fish, p,p'-DDE was the predominant congeners, except for northern snakehead (34% for p,p'-DDE and 30% for p,p'-DDT). The new source of DDTs to freshwater fish ponds was partly attributed to dicofol, whereas sewage discharged from the Pearl River Delta and anti-fouling paint were likely the DDTs sources to seawater farmed fish.     

Arsenic, copper, and zinc contamination in soil and wheat during coal mining, with assessment of health risks for the inhabitants of Huaibei, China

Field studies were conducted to investigate arsenic (As), copper (Cu), and zinc (Zn) contamination in agricultural soils and wheat crops at two areas in Huaibei, China. Area A is in the proximity of Shuoli coal mine. In area B, three coal mines and a coal cleaning plant were distributed. The potential health risk of As, Cu, and Zn exposure to the local inhabitants through consumption of wheat grains was also estimated. The results showed that significantly higher (p?<?0.05) concentrations of As, Cu, and Zn were found in soils collected from area B than in those from area A. Arsenic concentrations in wheat sampled from area A were negatively correlated with the distance from the coal mine (p?<?0.001). Concentrations of Cu and Zn in wheat seedlings and grains collected from area B were significantly higher (p?<?0.05) than in those collected from area A, with the exception of Zn in wheat seedlings. Concentrations of Cu and Zn in most wheat grain samples were above the permissible limits of Cu and Zn in edible plants set by the Food and Agriculture Organization/World Health Organization. The hazard index of aggregate risk through consumption of wheat grains was 2.3–2.4 for rural inhabitants and 1.4–1.5 for urban inhabitants. The average intake of inorganic As for rural inhabitants in Huaibei was above 10 μg day^?1. These findings indicated that the inhabitants around the coal mine are experiencing a significant potential health risk due to the consumption of locally grown wheat.     

Overview and assessment of techniques to measure ammonia emissions from animal houses: the case of the Netherlands

In order to comply with the ammonia (NH(3)) emission reduction assigned to the Netherlands development of new measures are needed, which should be supported by fast and accurate measurements to arrive at new estimates of the NH(3) emission from each agricultural source. This paper gives an overview of the current methods used in the Netherlands to measure NH(3) emissions from animal houses, and provides alternative methods for some particular situations. For mechanically ventilated animal houses, passive flux samplers placed in the ventilation shafts of the animal house are presented as alternative to measure a larger number of animal houses (replicates) with the same housing system at a low price. For naturally ventilated animal houses, when mixing in the animal house is not good enough to allow measurements within the animal house (internal tracer gas ratio method), two measurement methods are discussed: the Gaussian plume dispersion model, which is usually not suitable for agricultural situations, and the flux frame method, which is not always applicable because of distortion of the flow around the building. Finally, for animal houses with outside yards for the animals, there are at this moment no methods available to measure the NH(3) emissions from these complex situations, although quick box methods (for the outside yards) and a combination of a backward Lagrangian stochastic model with open-path concentration measurements with a tunable diode laser (TDL), look promising.