吸附法处理二硝基酚酸性废水的研究

采用吸附法处理二硝基酚酸性废水,进行了吸附剂筛选、吸附树脂吸附和解吸性能影响因素以及吸附寿命考察、设备防腐试验。选定 H-03型大孔吸附树脂为吸附剂,试验证明它具有非常良好的吸附稳定性。废水经过一次吸附处理,其中的二硝基酚得到回收,出水酚含量可从1200毫克/升降至10毫克/升以下,可达到排放标准要求的无色无味的指标。     

脂肪磺酸基阳离子交换树脂对Cr~(3+)的吸附和解吸性能

研究了脂肪磺酸基阳离子交换树脂(简称树脂)对Cr3+的吸附和解吸性能。在溶液初始Cr3+质量浓度为250mg/L、吸附温度为25℃、溶液pH为5的条件下,树脂对Cr3+的吸附量最大。Cr3+质量浓度在实验范围内,等温吸附过程均符合Langmuir和Freundlich方程,最大吸附量为18.6208mg/g。树脂对Cr3+的吸附在吸附时间为180min时趋于平衡,且吸附为液膜扩散控制。随吸附温度的升高(10～55℃),树脂对Cr3+的吸附量略有增加。用质量分数为5%的HCl溶液可将吸附在树脂上的Cr3+解吸,解吸率近100%,且重复5次吸附和解吸过程,树脂对Cr3+的吸附量基本保持不变。     

脂肪磺酸基阳离子交换树脂对Cr3+的吸附和解吸性能

研究了脂肪磺酸基阳离子交换树脂（简称树脂）对Cr3＋的吸附和解吸性能。在溶液初始Cr3＋质量浓度为250m∥L、吸附温度为25℃、溶液pH为5的条件下,树脂对Cr3＋的吸附量最大。Cr3＋质量浓度在实验范围内,等温吸附过程均符合Langmuir和Freundlich方程,最大吸附量为18．6208mg／g。树脂对Cr3＋的吸附在吸附时间为180min时趋于平衡,且吸附为液膜扩散控制。随吸附温度的升高（10～55℃）,树脂对Cr3＋的吸附量略有增加。用质量分数为5％的HCl溶液可将吸附在树脂上的Cr3＋解吸,解吸率近100％,且重复5次吸附和解吸过程,树脂对Cr3＋的吸附量基本保持不变。     

大孔吸附树脂处理酚类胺类和其再生

在pH5—9时,用大孔吸附树脂H-103吸附水体中的甲荼胺,以7%盐酸解吸,解吸液中甲荼胺量达15000ppm。在 pH3—7时,吸附水体中的苯酚或间苯二酚,以3%氢氧化钠溶液解吸,解吸液中酚量达5000ppm,间苯二酚量可达20000ppm。树脂经再生后可以重复使用。     

酸化碱渣对氨氮的吸附和解吸性能

研究了氨氮质量浓度、体系温度、时间、酸化碱渣溶液的pH等对酸化碱渣吸附氨氮性能的影响,比较了作为解吸剂的蒸馏水和NaCl溶液对氨氮的解吸效果。在选定的实验条件下,酸化碱渣对氨氮的最大吸附量可达13．9mg／g。氨氮吸附量随其质量浓度的增加而增大、随体系温度的升高而降低,酸化碱渣溶液的pH对吸附性能的影响可以忽略。酸化碱渣表面吸附作用力主要为偶极间力和氢键力,吸附过程可用一级动力学方程模拟。NaCl溶液对氨氮的解吸效果好于蒸馏水,最大解吸率为25．7％。     

国外动态

用超声波解吸活性炭吸附的酚ＤＥＰ，９４［７］，１３（１９９８）美国密执安州化学与生物医药大学的研究人员发现，用超声波可轻而易举地将活性炭及聚合树脂吸附的难以解吸的酚解吸下来。研究人员还发现，解吸温度降低，酚的解吸速率增大；使用一种曝气液体介质和增大超...     

我国应用树脂吸附法处理有机废水的进展

介绍了我国近十年来应用树脂吸附法处理有机废水的研究成果和应用实例，处理结果表明，吸附树脂具有吸附效果好，脱附再生容易，性能稳定，适用范围宽，实用性好等特点，该法可用于处理含酚，苯胺，有机酸，硝基物，农药，染料中间体等废水，是一种处理有机废水的有效方法。     

大孔树脂NKA-II对双酚A的吸附性能

研究了大孔树脂NKA-II对双酚A（BPA）的吸附性能,考察了吸附过程的动力学、热力学及树脂的再生性能。BPA溶液呈弱酸性,不需调节pH可直接进行吸附。BPA在大孔树脂NKA-II上的吸附过程可用准二级动力学方程很好地描述。树脂对BPA的吸附是吸热反应,符合Freundlich等温吸附方程,吸附过程属于可自发进行的物理吸附。BPA的吸附过程中同时存在着溶剂的解吸。大孔树脂NKA-II具有良好的重复使用性能,新树脂的平衡吸附量为10.44 mg/g,再生20次后平衡吸附量仍为10.43 mg/g。     

树脂吸附-Fenton 试剂氧化法预处理炼油碱渣废水

采用树脂吸附-Fenton 试剂氧化组合工艺对某炼油企业炼油碱渣废水进行预处理.实验确定的最佳工艺条件为:3 种树脂串联吸附,废水流量0.33 mL/ min,H2O2加入量0.20 mol / L,n（H2O2）1 n（Fe2 +）= 12,Fenton 试剂氧化进水pH 3,Fenton 试剂氧化反应时间120 m...     

碱渣对Cd2+的吸附特性研究

研究了碱渣对溶液中Cd2＋的吸附特征。实验结果表明,碱渣对Cd2＋的吸附量随温度升高而降低,随Cd2＋初始质量浓度增加而增大,随体系pH升高而增大。当体系pH〈7．52时,表面吸附起主导作用,吸附作用力主要为偶极间力和氢键力,碱渣对Cd2＋的吸附热力学可用Freundlich等温吸附方程较好地描述;而当吸附体系pH〉8．00时,吸附作用力主要为化学键力,吸附过程可用Langmuir等温吸附方程较好地描述。当体系pH=7．00时,碱渣对Cd2＋的吸附动力学用二级动力学方程拟合效果最佳;当体系pH为8．00和9．01时,用Langmuir动力学方程拟合的效果最佳。     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

Application of Cellulose Microfibrils in Polymer Nanocomposites

Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.     

四氮唑废水处理工艺设计

高浓度、高盐分的四氮唑生产废水通过三效蒸发浓缩,馏出液经铁炭氧微电解和混凝预处理,再采用水解酸化一接触氧化一反应二沉主体组合工艺进行处理。研究了该工艺所需构筑物和设备的设计与选型。该工艺在正常运行条件下,处理后出水pH6～9,COD 302mg／L,BOD5 108mg／L,SS30mg／L,色度36倍,水质达到GB8978--1996（污水综合排放标准》三级标准。     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.     

Does Soil Acidification Affect Spruce Needle Chemical Composition and Tree Growth?

In 1994, a large survey of soil chemistry was undertaken in thecounty of Värmland in central Sweden (Lundström et al., 1998).The southern part of the county was affected by soilacidification whereas there were no such indications in thenorthern part. To investigate the influence of soil chemistryon the trees at the specific sites, the survey was continued byan analysis of needle chemistry (Norway spruce) which wasundertaken at 150 of the 180 sites, and of tree growth at 65 ofthe 180 sites. Growth was expressed as a ratio between expectedgrowth, estimated with a national, empirical growth model, andthe growth observed in the field. In statistical analyses,using rank correlation, PCA and PLS, there were only weakindications of an influence of soil chemistry on needlechemistry and on tree growth. A moderate correlation betweennitrogen and sulphur in needles was found, which wasinterpreted as an effect of deposition and of processes in thetree canopy. No obvious regional pattern of the growth ratiowas found, in contrast to the clear pattern of soilacidification. The statistical analysis could not with anycertainty point out any of the soil chemistry variables asespecially important for the tree growth ratio.     

Solubility and Potential Mobility of Heavy Metals in Two Contaminated Urban Soils from Stockholm,Sweden

The solubility and potential mobility of heavy metals (Cd, Cu,Hg, Pb and Zn) in two urban soils were studied by sequential andleaching extractions (rainwater). Compared to rural (arable) soils on similar parent material, the urban soils were highlycontaminated with Hg and Pb and to a lesser extent also with Cd,Cu and Zn. Metal concentrations in rainwater leachates were related to sequential extractions and metal levels reported fromStockholm groundwater. Cadmium and Zn in the soils were mainly recovered in easily extractable fractions, whereas Cu and Pb were complex bound. Concentrations of Pb in the residual fractionwere between two- and eightfold those in arable soils, indicatingthat the sequential extraction scheme did not reflect the solidphases affected by anthropogenic inputs. Cadmium and Zn conc. inthe rainwater leachates were within the range detected in Stockholm groundwater, while Cu and Pb conc. were higher, whichsuggests that Cu and Pb released from the surface soil were immobilised in deeper soil layers. In a soil highly contaminatedwith Hg, the Hg conc. in the leachate was above the median concentration, but still 50 times lower than the max concentration found in groundwater, indicating the possibilityof other sources. In conclusion, it proved difficult to quantitatively predict the mobility of metals in soils by sequential extractions.     

Biodegradation of Injection Molded Starch-Poly (3-hydroxybutyrate-co-3-hydroxyvalerate) Blends in a Natural Compost Environment

Injection molded specimens were prepared by blending poly (hydroxybutyrate-co-valerate) (PHBV) with cornstarch. Blended formulations incorporated 30% or 50% starch in the presence or absence of poly-(ethylene oxide) (PEO), which enhances the adherence of starch granules to PHBV. These formulations were evaluated for their biodegradability in natural compost by measuring changes in physical and chemical properties over a period of 125 days. The degradation of plastic material, as evidenced by weight loss and deterioration in tensile properties, correlated with the amount of starch present in the blends (neat PHBV < 30% starch < 50% starch). Incorporation of PEO into starch-PHBV blends had little or no effect on the rate of weight loss. Starch in blends degraded faster than PHBV and it accelerated PHBV degradation. Also, PHBV did not retard starch degradation. After 125 days of exposure to compost, neat PHBV lost 7% of its weight (0.056% weight loss/day), while the PHBV component of a 50% starch blend lost 41% of its weight (0.328% weight loss/day). PHB and PHV moieties within the copolymer degraded at similar rates, regardless of the presence of starch, as determined by ¹H-NMR spectroscopy. GPC analyses revealed that, while the number average molecular weight (Mn) of PHBV in all exposed samples decreased, there was no significant difference in this decrease between neat PHBV as opposed to PHBV blended with starch. SEM showed homogeneously distributed starch granules embedded in a PHBV matrix, typical of a filler material. Starch granules were rapidly depleted during exposure to compost, increasing the surface area of the PHBV matrix.     

Effects of Nitrogen Deposition on Bryophyte Species Composition of Calcareous Grasslands

Regular additions of NH₄NO₃ (35–140 kg N ha⁻¹ yr⁻¹) and (NH₄)₂SO₄ (140 kg N ha⁻¹ yr⁻¹) to a calcareous grassland in northern England over a period of 12 years have resulted in a decline in the frequency of the indigenous bryophyte species and the establishment of non-indigenous calcifuge species, with implications for the structure and composition of this calcareous bryophyte community. The lowest NH₄NO₃ additions of 35 kg N ha⁻¹ yr⁻¹ produced significant declines in frequency of Hypnum cupressiforme, Campylium chrysophyllum, and Calliergon cuspidatum. Significant reductions in frequency at higher NH₄NO₃ application rates were recorded for Pseudoscleropodium purum, Ctenidum molluscum, and Dicranum scoparium. The highest NH₄NO₃ and (NH₄)₂SO₄ additions provided conditions conducive for the establishment of two typical calcifuges – Polytrichum spp. and Campylopus introflexus, respectively. Substrate-surface pH measurements showed a dose-related reduction in pH with increasing NH₄NO₃ deposition rates of 1.6 pH units between the control and highest deposition rate, and a further significant fall in pH, of >1 pH unit, between the NH₄NO₃ and (NH₄)₂SO₄ treatments. These results suggest that indigenous bryophyte composition may be at risk from nitrogen deposition rates of 35 kg N ha⁻¹ yr⁻¹ or less. These effects are of particular concern for rare or endangered species of low frequency.