基于CFD的滤袋内侧磨损失效过程分析

针对某燃煤热电厂袋式除尘器滤袋破损和多次换袋检修失效现象,采用气固两相流数值模拟方法,对清灰气流含尘浓度过高导致滤袋破损失效的演变过程进行了分析,并结合现场调研和破损滤袋检测结果,明确了产生此类故障的原因.结果表明:喷吹总气量的22％为诱导气流,袋口上方的诱导气流速度接近7 m·s-1,上箱体内悬浮颗粒甚至袋口周边沉积...     

基于量纲分析的转载点诱导气流影响因素分析与应用

为解决转载点粉尘污染问题,采用量纲分析法将影响转载点诱导风量的因素进行分类推演,建立转载系统诱导风量计算模型,并搭建转载点诱导气流实验装置,系统分析物料在转载过程中给料量、落料高差、下料管倾角和皮带运行速度等因素对产生诱导气流的影响,拟合得出转载点诱导风量计算模型的数学表达式。结果表明:转载点物料的给料量和落料高差是影响诱导风量的主要因素;对量纲分析所得模型利用实验数据进行拟合所得各参数系数的标准误差优于0.032 1,实验结果与数学模型计算结果误差小于9.48%。该计算模型可用于估算转载点诱导风量大小,为现场的粉尘治理及生产实践提供参考依据。     

烟气和粉尘性质对除尘效率影响的仿真研究

应用欧拉-拉格朗日多相流模型对影响电除尘器内部气流分布的烟气含尘浓度、烟气湿度、粉尘粒径及真密度等因素进行了数值仿真。分析了烟气和粉尘性质对除尘效率的影响。由于在仿真过程中考虑了烟气特性和粉尘性质等因素,不仅可获得各因素对气流分布均匀性的影响,而且仿真结果更能反映电除尘器气流分布的实际情况。提出的烟气和粉尘性质仿真方法可以为电除尘器除尘效率分析提供新的途径。     

粉尘对电除尘器气流分布影响仿真研究

为了更加精确地研究电除尘器入口气流分布特征, 论文采用欧拉-拉格朗日多相流模型,对电除尘器内部气流分布进行了数值仿真。由于在进入除尘器的气流中引入了粉尘粒子,不仅可获得粉尘及粉尘颗粒粒径大小对气流分布均匀性的影响,而且这种模拟更加接近除尘器的气流实际情况。提出的模拟方法为电除尘器的气流分析提供了一条新的途径。     

基于DPM模型求解自由下落颗粒羽流卷吸空气量

为深入了解自由下落颗粒羽流卷吸空气的特性,对氧化铝颗粒从出口直径为5 mm的圆形孔中自由下落的气固两相流场进行了数值模拟研究。依据RNG k-ε模型求解气相雷诺时均N-S方程并进行离散化处理,采用DPM模型跟踪单个粒子以求解颗粒的运动方程,并通过SIMPLE双向耦合,对自由下落颗粒羽流流动特性进行数值模拟。结果表明:自由下落颗粒羽流卷吸空气气相速度在羽流中心线上处于最大值,随着径向距离的增大速度值明显地减小,直到距离中心线30 mm处,之后速度的变化趋于稳定;颗粒在净质量力作用下沿质量力方向首先作加速运动,之后下落速度u_p随着下落高度的变化趋于平缓,羽流末端颗粒运动基本遵守颗粒自由沉降规律;羽流卷吸空气量随着下落高度的增加而增大,其规律与颗粒群模型给出的结果高度吻合。通过比较分析发现,采用DPM模型很好的解决了对颗粒相运动方程的求解并可获取颗粒运动轨迹,对于自由下落颗粒羽流特性的分析不失为一种有效而可行的方法。     

综采工作面旋转风幕隔尘实验研究

为了研究综采工作面旋转风幕隔尘机理及其隔尘效率,对旋转风幕隔尘下的综采工作面粉尘浓度分布及其隔尘效率开展了模型实验研究。研究结果表明,(1)在相同工况下,旋转风幕对全尘和呼吸性粉尘的隔尘效率高于普通空气幕,且对呼吸性粉尘的隔尘优势更为明显;(2)出口风速对隔尘效果的影响较大,存在一个最佳的出口风速,在该风速下旋转风幕对全尘和呼吸性粉尘均保持较高的隔尘效率;(3)当出口风速低于最佳风速时,旋转风幕对全尘和呼吸性粉尘的隔尘效率均随着风速的增加而显著提高;当出口风速高于最佳风速时,随着出口风速的增加全尘隔尘效率不断下降,且呼吸性粉尘隔尘效率提升不明显;(4)旋转风幕对于不同粒径的粉尘的隔尘效率存在差异,随着粉尘粒径的增加,旋转风幕的隔尘效率不断下降。     

双层滤料颗粒床高温除尘器灰斗气固两相流场模拟分析

为了促进粉尘沉降,在双层滤料颗粒床高温除尘器灰斗处增加了一个抽气外循环并且在抽气口附近增设挡板,使用Fluent软件对除尘器的气固两相流场进行数值模拟,在抽气循环率为1/6情况下,分析不同挡板的布置方式时粉尘的沉降率。仿真结果表明:当挡板气流通道宽300 mm、高1 400 mm、层间距100 mm、层数6层时,可以大幅增加粉尘沉降率,与无挡板布置方式相比,粉尘粒径为1、25、50μm的沉降率分别增加了27.15%、28.9%、35.19%。通过分析可知,挡板气流通道宽度、挡板高度和挡板层数的变化对于100μm以下粒径的粉尘颗粒沉降效果影响较为明显。     

粉尘颗粒在单纤维表面沉积的计算机模拟

采用随机模拟方法模拟研究了粉尘颗粒在单纤维表面上的沉积过程,Kuwabara流场用于计算粉尘颗粒运动的轨迹,模拟中考虑了粉尘颗粒的粒径分布和单纤维在气流作用下的扭曲行为对粉尘颗粒沉积的影响.模拟结果表明.粉尘颗粒在单纤维表面上的沉积形态与分布特征依赖于Stokes数、粉尘颗粒粒径分布和纤维扭曲程度;模拟获得的粉尘树枝结构与相关文献提供的实验结果相似.     

输煤皮带转载点密闭罩流场模拟与结构优化

为了研究输煤皮带转载点密闭罩内流场对吸尘效果的影响,采用Fluent软件对某转载点密闭罩内气固两相流动情况进行了数值模拟。通过气流分布和煤尘浓度分布的分析,发现溜槽转折处较大的气流偏转会增加煤尘起尘量和导致局部煤尘积聚,吸尘罩的开口角度对吸尘效果也有较大影响。为了疏导气流并加强吸尘效果,提出了溜槽转折处和吸尘罩的结构优化设计方案。研究表明,改进后气流分布更加均匀,吸尘效果有所提高,从而为转载点密闭罩的优化设计提供了参考。     

滤筒除尘器脉冲清灰动态分析

对常用规格φ325 mm×660 mm滤筒采用普通喷吹孔和诱导喷嘴进行脉冲清灰实验研究,测试滤筒侧壁压力峰值和压力上升速度,并使用高速动态分析仪拍摄清灰时粉尘从滤筒壁面脱落的动态过程。实验证明了滤筒脉冲清灰时,粉尘的脱落是从滤筒上部到下部依次进行,滤筒侧壁第一个压力峰值、最大压力峰值和压力上升速度对清灰效果均有影响,且脉冲气流形成的第一个侧壁压力峰值对滤筒的第一次冲击对清灰来说起着决定性的作用,回流气流形成的侧壁压力峰值作用较弱。而压力上升速度不能完全作为评价清灰效果好坏的指标。实验证明,采用诱导喷嘴可以改善滤筒内部流场,提高清灰效率。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.