pH对磷酸铵镁结晶介稳区、诱导期和反应速率的影响

以p H为控制参数,利用自组装激光测量装置测定了4、20、30和40℃时,磷酸铵镁在水溶液中的溶解度、超饱和度和介稳区宽度等基础数据,分析了不同温度和p H下磷酸铵镁结晶介稳区的变化规律,考察了p H对磷酸铵镁结晶诱导期和结晶反应速率的影响。结果表明,提高溶液的p H,可降低磷酸铵镁在水溶液中的溶解度和超饱和度,但同时磷酸铵镁结晶介稳区宽度有所增加;磷酸铵镁的溶解度和超饱和度随温度的升高呈现上升的趋势,而磷酸铵镁的结晶介稳区宽度则随温度的升高而变窄,提高溶液中MAP的物质浓度也会压缩结晶介稳区宽度;随着溶液p H的升高,磷酸铵镁的结晶诱导期逐渐缩短,同时其结晶反应速率也有明显的提升。在磷酸铵镁结晶除磷过程中,可以通过控制p H来优化反应工艺条件,促进磷酸铵镁结晶反应的进行。     

K-Ca-Mg-Cl-H_2O体系中硫酸钙结晶介稳区的研究

对K-Ca-Mg-Cl-H2O体系中硫酸钙结晶介稳区进行了研究。以一定浓度氯化钙溶液与硫酸镁溶液反应结晶的方式,采用激光散射法测定了不同浓度复合盐溶液和温度下硫酸钙过饱和度与结晶之间的关系,并测定了与之平衡的溶解度,从而确定该体系中硫酸钙结晶介稳区宽度,探讨了影响结晶介稳区的因素,以及硫酸钙结晶和结晶相与复合盐溶液浓度、温度、结晶介稳区之间的关系。     

K-Ca-Mg-Cl-H2O体系中硫酸钙结晶介稳区的研究

对K-Ca-Mg-Cl-H2O体系中硫酸钙结晶介稳区进行了研究.以一定浓度氯化钙溶液与硫酸镁溶液反应结晶的方式,采用激光散射法测定了不同浓度复合盐溶液和温度下硫酸钙过饱和度与结晶之间的关系,并测定了与之平衡的溶解度,从而确定该体系中硫酸钙结晶介稳区宽度,探讨了影响结晶介稳区的因素,以及硫酸钙结晶和结晶相与复合盐溶液浓度...     

旋转盘反应器光催化降解苯酚废水动力学

采用旋转盘反应器(SDR)降解苯酚废水,对苯酚初始浓度、溶液p H值、H2O2的添加对其光催化降解动力学的影响进行了研究。结果表明,SDR内的光催化降解动力学特征符合一级反应动力学规律。苯酚初始浓度越低,反应速率常数k值越大;溶液p H=2时的降解速率高于其他p H值;H2O2的协同作用使苯酚的降解速率明显提高,其速率常数k值为未添加H2O2时的78倍。     

超声-Fenton联用技术深度处理皮革综合废水生化出水

针对皮革综合废水生化处理出水中存在COD和色度偏高等问题,提出采用超声-Fenton联用技术对生化后的皮革综合废水进行深度处理。通过单因素实验考察了超声功率、H2O2投加量、Fe2+投加量(即H2O2/Fe2+比)、溶液pH和反应时间对水样中COD和色度去除率的影响;正交实验结果表明,当溶液初始pH值为4.0时,各因素影响显著性的先后顺序为H2O2>超声功率>反应时间>Fe2+;其优化的实验条件为:H2O2为24.0 mL/L、超声功率为85 W、反应时间为45min、Fe2+为2.2 g/L,经超声-Fenton联用技术深度处理后COD的去除率可达85.4%。在最佳实验条件下,对超声-Fenton联用技术深度处理皮革综合废水生化出水的动力学研究发现,水样中的COD降解反应符合表观一级反应动力学,速率常数增强因子可达8.64,表明存在显著的协同效应。     

超声-Fenton高级氧化降解染料工业废水的研究

采用超声与Fenton高级氧化技术联合处理染料废水,取得了满意的效果。同时考察了初始浓度、初始pH值、超声时间、超声频率、超声功率、H2O2和FeSO4初始浓度等因素对其COD去除效果的影响,当超声波频率为45 kHz,功率为200 W,初始pH值为2.63,超声时间为150 min,H2O2浓度为60 mmol/L,FeSO4浓度为12 mmol/L时,染料废水COD去除率达到91.8%。     

亚铁催化声化学降解罗丹明B

比较了不同金属离子对罗丹明B的声化学降解作用,发现超声时加入Fe2 反应速率常数为单独超声波降解时的1.6倍,反应在前5 h内符合假一级动力学.研究了亚铁离子强化声化学对罗丹明B的降解作用,考察了Fe2 用量,溶液初始pH值,曝气,反应温度和超声功率等因素对脱色速率的影响.研究表明,酸性条件有利于染料的脱色;有曝气时的声化学脱色速率常数是单独超声时的6倍;声化学反应的活化能较低,反应在低温就可以进行;超声功率的改变对脱色速率的影响不大.UV-VIS扫描图谱显示,染料在225 nm和256 nm处的紫外吸收明显降低,初步探讨了罗丹明B的降解机理.     

亚铁催化声化学降解罗丹明B

比较了不同金属离子对罗丹明B的声化学降解作用，发现超声时加入Fe^2＋反应速率常数为单独超声波降解时的1．6倍，反应在前5h内符合假一级动力学。研究了亚铁离子强化声化学对罗丹明B的降解作用，考察了Fe^2＋用量，溶液初始pH值，曝气，反应温度和超声功率等因素对脱色速率的影响。研究表明，酸性条件有利于染料的脱色；有曝气时的声化学脱色速率常数是单独超声时的6倍；声化学反应的活化能较低，反应在低温就可以进行；超声功率的改变对脱色速率的影响不大。UV-VIS扫描图谱显示，染料在225nm和256nm处的紫外吸收明显降低，初步探讨了罗丹明B的降解机理。     

不同诱导条件对结晶产物形貌特征的影响

在流化床反应器中,以含铜废水为处理对象,重点考察了诱导条件改变对结晶系统运行效率及结晶产物形貌特征的影响。结果表明,进水200 mg/L,进药比([Cu2+]/[CO2-3])1∶1.2,p H为10.2的条件下,铜离子去除率可接近100%,诱导晶种表面平滑,诱导颗粒生长成致密杆状晶体结构,以碳酸盐为沉淀剂的诱导结晶系统依赖于体系的p H,高p H体系下发生的共结晶现象是影响系统运行的主要原因;随着进药摩尔比的增加,结晶产物由短杆状向球状转化,晶体机械强度显著降低大量破碎,影响出水水质;进药比1∶1.2,p H为11的条件下,含铜废水浓度为500 mg/L时,系统去除率可达95%以上,微晶产率低于5%。     

水溶液中活性艳红KE-3B的臭氧超声联合脱除

采用臭氧/超声联合技术去除模拟废水中的活性艳红KE-3B。臭氧/超声处理前后KE-3B的紫外可见吸收谱没有明显的变化。臭氧/超声联合作用、单独臭氧化和单独超声处理脱除活性艳红KE-3B模拟废水5 min后的去除率分别为97%、73%和5%,表明臭氧/超声联合降解活性染料具有更高的氧化速率。实验研究了pH值、臭氧投加量、超声能量密度、反应温度对超声/臭氧降解活性艳红KE-3B反应速率的影响,在实验研究范围内,随着溶液初始pH的增大,KE-3B的去除率先增大后减小,超声能量密度的改变对KE-3B的去除影响不大,温度升高有利于氧化反应的进行。在溶液初始pH值为9.0,臭氧投加量3.2 g/h,超声能量密度176 W/L,反应温度20℃时,浓度为100 mg/L的活性艳红KE-3B溶液的去除率最高。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.