反胶束漆酶/纤维素酶体系中油酸酯化的优化

漆酶和纤维素酶在反胶束水核中心具有较强的催化活性。为了对反胶束酶体系中油酸酯化反应深入研究,采用生物表面活性剂鼠李糖脂构建反胶束体系作为漆酶与纤维素酶酯化油酸的催化反应场所。通过实验研究了反胶束体系的不同条件对酯化产物含量的影响。对于反胶束漆酶体系,最佳酯化条件为:含水量W040%,鼠李糖脂临界胶束浓度20mmol·L~(-1),pH值4,温度40℃;对于反胶束纤维素酶体系,最佳酯化条件为:含水量20%,鼠李糖脂临界胶束浓度80 mmol·L~(-1),pH值4,温度30℃。综合考虑几个因素,漆酶比纤维素酶更适合应用于反胶束中油酸的酯化。研究同时采用荧光光谱法对漆酶和纤维素酶在反胶束体系中结构性能的变化进行研究,结果表明,当反胶束体系处于最佳酯化反应条件时,荧光强度最高。     

醋酸纤维素包埋非水溶性介体催化强化生物反硝化特性

利用醋酸纤维素包埋法固定非水溶性醌类介体,研究其催化强化Paracoccus versutus菌株GW1的反硝化作用。结果表明,醌浓度在26.7 mmol/L时,固定化蒽醌(AQ)、1-氯蒽醌(1-AQ)、2-氯蒽醌(2-AQ)、1,5-二氯蒽醌(1,5-AQ)、1,8-二氯蒽醌(1,8-AQ)和1,4,5,8-四氯蒽醌(1,4,5,8-AQ)催化反硝化效率依次为:1,5-AQ1,8-AQ1,4,5,8-AQAQ1-AQ空白对照2-AQ。反应10 h时,1,5-AQ可使硝酸盐去除率比空白对照提高1.84倍;硝酸盐氮反硝化动力学拟合为零级反应,其速率常数Kx随1,5-AQ浓度的增加均呈线性增加(Kx=0.1885C1,5-AQ+8.378);水中溶解氧会降低GW1菌反硝化的效果;投加1,5-AQ的反硝化体系中亚硝酸盐积累的最大值比不投加介体的低48.3%;醋酸纤维素介体小球经过4次的重复利用,催化效果始终是空白对照的1.5倍以上。醋酸纤维素固定化非水溶性醌可以有效加速生物反硝化,表明其是一种较优的醌固定化方法,具有良好的应用价值。     

固定化氧化还原介体加速亚硝酸盐生物反硝化作用

考察了利用循环伏安法所制备的固定化氧化还原介体(AQS/PPy/ACF)加速亚硝酸盐生物反硝化的特性,及其降解过程中pH和氧化还原电位(ORP)的变化特征。结果表明,AQS/PPy/ACF可显著地加速亚硝酸盐的生物降解;在不考虑各因子间交互作用的条件下,AQS/PPy/ACF加速亚硝酸盐降解的最佳条件为温度35℃,pH=8和碳氮比为6;AQS/PPy/ACF加速亚硝酸盐生物反硝化过程中pH的变化趋势与传统的亚硝酸盐生物反硝化过程中pH的变化趋势相似;AQS/PPy/ACF的加入可使亚硝酸盐生物反硝化过程中的ORP降低约45 mV;AQS/PPy/ACF具有较好的催化稳定性。本研究可为亚硝酸盐的生物降解提供新的技术途径,并为该技术的实际应用提供理论基础。     

氧化石墨烯/Fe_3O_4磁性纳米材料固定辣根过氧化物酶及其降解酚类物质

以原位沉淀法制备的氧化石墨烯/Fe3O4磁性纳米复合颗粒为固定化载体,1-乙基-(3-二甲基氨基丙基)碳二亚胺盐酸盐为交联剂,成功固载了辣根过氧化物酶。探讨了固定化条件对辣根过氧化酶活性的影响以及固定化酶的理化性质,实验结果表明,固定化最佳pH为6、温度为30℃、时间为11 h、交联剂浓度为1 mg/L。与游离酶相比,固定化酶具有良好的pH稳定性和热稳定性。最后将固定化酶用于降解水中的苯酚和2,4-二氯酚,并考察了固定化酶的重复利用性。     

生物炭和碳纳米管固定化漆酶去除水体雌二醇

漆酶是一类具有高效的催化氧化能力的含铜多酚的氧化酶,而固定化漆酶技术在有机废水处理领域受到了越来越多的关注。通过比较吸附法和包埋法利用木炭(WB)、竹炭(BB)和碳纳米管(CNT)固定游离漆酶去除水体雌二醇(E2)。在25°C、pH=5条件下,固定化漆酶经120 h贮存仍保留80%的活性。经过5次循环研究,固载的漆酶仍保留了27%～58%的剩余活性。结合扫描电子显微镜和傅里叶变换红外光谱,证实了漆酶成功地负载在碳基材料上。仅在8 h内,50 mg·L^-1 E2通过吸附法制备的WB、BB、CNT固定化漆酶去除了42.92%、47.66%、43.92%,而包埋法制备的WB、BB、CNT固定化漆酶分别去除84.08%、87.20%、87.86%。结果表明,包埋法固定化漆酶对E2的去除效率更优,这是由于包埋固载在生物炭和CNT的漆酶更为稳定。此外,K⁺和Mn²⁺离子可能通过干扰漆酶的电子传递过程影响漆酶的活性,从而抑制E2的去除。本研究旨在为固定化漆酶在有机废水处理的实际应用提供指导。     

基于生物表面活性剂的柴油微乳体系构建与性能研究

以生物表面活性剂鼠李糖脂（RL）为表面活性剂,中长碳链正构醇（正丁醇、正戊醇、正己醇、正庚醇及正辛醇）为助表面活性剂,采用滴定法制备RL／柴油／正构醇／水柴油微乳体系,并考察了表面活性剂用量（Km）、助表面活性剂醇的种类及用量（δas）及离子强度对柴油微乳体系最大增溶水量（Wo）的影响,并对不同条件下获得的柴油微乳体系的运动粘度（μ）和表面张力（γ）进行了表征。通过荧光法测得RL在柴油中的临界胶束浓度CMC为7g／L。当生物表面活性剂与柴油的质量比Km为0．02,助表面活性剂选用正庚醇且醇与表面活性剂的质量比δgs为0．1,NaOH溶液质量分数为0．06％时,柴油微乳体系的肛和T较低,形。最大,性能较佳。     

菌株Arthrobacter sp.DNS10降解酶固定化条件的响应面优化

以前期分离得到阿特拉津降解菌株Arthrobacter sp.DNS10为供试菌株,选取海藻酸钠作为固定化材料,采用响应面法优化该菌株所包含的降解酶的固定化条件。借助Plackett-Burman设计筛选确定海藻酸钠浓度、固定化体系的p H值、加酶量和Ca Cl2溶液质量分数4个因素作为影响固定化酶比酶活的典型因素。借助Box-Behnken设计及响应面回归分析拟合,确定适宜上述降解酶的最佳包埋固定化条件及方法为:在每10 m L海藻酸钠浓度为1.93%,p H为8.5的固定化基质中加入983μL的降解酶液(蛋白浓度为88μg·L-1),然后利用注射器将上述混合溶液滴加到质量分数为2.7%的Ca Cl2溶液中即可制备出比酶活最高的固定化酶,实际测定固定化酶的最优比酶活为0.190 2 U·mg-1(预测值为0.187 4U·mg-1)。上述固定化酶平均粒径约为(0.44±0.01)cm,其在连续6次的使用过程中比酶活仍能保持在初始值的77.5%以上。上述固定化处理可有效的改善降解酶的环境贮存特性,固定化酶在常温下保存35 d后比酶活仍能保持在其初始状态的12.34%,而游离酶则无活性检出。     

芦苇生物炭复合载体固定化微生物去除水中氨氮

为了去除水体中的氮素并实现水生植物的有效利用,以芦苇生物炭为无机载体,结合海藻酸钠(SA)、聚乙烯醇(PVA)作为复合载体,固定驯化后的硝化污泥制成固定化颗粒,去除水中氨氮。通过考察固定化颗粒机械强度、酸碱稳定性及传质性能,探究了生物炭添加量及生物炭粒径对固定化颗粒降解氨氮性能的影响。结果表明,芦苇生物炭有丰富的孔结构,表面含有较多的含氧官能团和胺基、磺酸基、羧基和酰胺基等基团,从而具有良好的吸附性能以及较强的酸碱缓冲能力,有利于微生物的黏附和增殖。以添加芦苇生物炭作为复合载体,固定化颗粒的破损率降低了2.4%,酸碱稳定性和传质性分别提升12.5%和55.8%;在72 h内,可以使氨氮降解率达到96.3%。此外,不同粒径生物炭的固定化颗粒对氨氮的吸附量有显著影响,随着生物炭粒径从0.60 mm减小至0.15 mm,氨氮的最大吸附量可以从0.30 mg·g~(-1)增加到0.46 mg·g~(-1)。因此,在固定化微生物的载体中添加生物炭,可以提升固定化颗粒性能,打通微孔孔道从而有利于基质的运输和扩散;同时减小生物炭粒径,为微生物提供更多的吸附位点,从而显著提高固定化微生物对氨氮的降解能力。     

镉胁迫下固定化菌系菲降解能力及环境适应性研究

采用核桃壳质生物炭为固定化材料，以铜矿污泥和焦化废水污泥微生物为混合菌源，通过正交试验确定了优化的固定化条件：0.1 g 16目生物炭，微生物接种量5 mL(600 nm下的吸光度(OD₆₀₀)=1.0),固定时间36 h,此时固定化菌系可在48 h降解76.13%的菲。温度20～40℃、pH 4.00～9.00范围内，固定化菌系的降解能力优于游离态菌系。在温度为30℃、pH为7.00时，培养7 d后，固定化菌系对菲的降解率高达95.94%。固定化菌系在低温、低pH下均表现出更强的适应性，对菲的降解率比游离态菌系更高。此外，固定化体系中生物炭水溶提取物可充当共代谢碳源，促进菌系的生长。     

煤化工高盐废水臭氧催化氧化脱除COD

针对煤化工高盐废水中有机物难降解问题,采用浸渍-煅烧法制备了负载有活性金属氧化物的活性氧化铝型催化剂,探索催化剂的制备工艺和反应操作条件对废水COD去除率的影响。结果表明:活性氧化铝载体催化性能优于陶粒,活性氧化铝负载Cu、Mn、Ni的催化活性较高,将2种活性组分进行组合制得的MnO_xNiO_x/γ-Al_2O_3催化剂,在经过60 min的臭氧催化氧化后,COD的去除率可达51.3%;利用BET、SEM-EDS、XRD对催化剂进行了表征和分析,Mn、Ni成功负载到活性氧化铝表面和孔隙内,2种元素负载量摩尔比约为2:1,且主要以氧化物形式存在;通过计算臭氧利用效率,发现MnO_x-NiO_x/γ-Al_2O_3臭氧催化氧化的_η值低于单独的臭氧氧化,这意味着通过MnO_x-NiO_x/γ-Ak_2O_3催化剂可以有效地将臭氧分解成活性氧;通过优化臭氧和催化剂投加量后发现,在臭氧为350 mg·(L·h)~(-1)、催化剂投加量为100 g·L~(-1)废水中,反应180 min后,COD去除率可达到72.3%;在连续进行4 h的臭氧催化氧化实验后,MnO_x-NiO_x/γ-Al_2O_3稳定性和重复利用性均较好,COD去除率能维持在约42%,锰、镍离子的溶出量均小于0.5 mg·L~(-1)。以上研究结果可为高效的臭氧催化体系在煤化工高盐废水处理领域的应用提供参考。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.