常温下ABR处理低浓度废水性能及污泥特性

研究了常温(17~25℃)下4隔室厌氧折流板反应器(ABR)处理低浓度废水的运行效果及污泥特性。在水力停留时间(HRT)为24 h,进水COD浓度为1 500、1 000和500 mg/L左右时,平均COD去除率分别为94%、93%和87%。进水COD浓度保持在500 mg/L左右,将HRT降为12 h和8 h,COD的去除率仍达到83%以上。厌氧污泥性质测定结果表明,最后隔室中的污泥浓度、颗粒化程度及产甲烷活性与其他隔室相比明显较低,说明低浓度进水对最后隔室厌氧污泥的性质影响较大。颗粒污泥扫描电镜观察显示,各隔室颗粒污泥内部微生物组成差异较大,第1隔室颗粒污泥以产甲烷球菌为主,第2隔室颗粒污泥中没有明显的优势菌,但杆状菌比第1隔室明显较多,第3、4隔室颗粒污泥中以索氏甲烷丝菌为优势菌。     

垃圾渗滤液对厌氧颗粒污泥稳定性的影响

在升流式厌氧反应器中,分别以模拟废水和最优进水浓度渗滤液持续进水,探讨COD、NH+4-N和SO2-4浓度对反应器内颗粒污泥的稳定性的影响。结果表明,按照优化浓度进水,可以在一定程度上提高了厌氧生物处理效率,COD、NH+4-N和SO2-4去除率分别约为60%、11%和42%。渗滤液中微量元素(如Fe、Co和Ni等)有利于提高污泥浓度,增大反应器内生物量。改变垃圾渗滤液进水的COD、NH+4-N和SO2-4浓度,使得颗粒污泥多处于0.9~1.6 mm之间,具有高传质效率和不易破碎的特性。污泥颗粒的沉降速度保持在28.52~67.87 m·h-1之间,属于沉降性能良好的污泥。以最优进水浓度渗滤液为进水条件的反应器内的颗粒污泥浓度、粒径和沉降速度都要比模拟废水组更好,说明渗滤液中的微量元素存在,有利于颗粒污泥的稳定。     

碳源类型及进水量分配对CMICAO工艺脱氮除磷的影响

研究了分别以葡萄糖和乙酸钠为碳源时多点交替进水阶式A2/O(CMICAO)工艺氮磷的去除效果,以及在不同进水C/N比时各进水量分配对脱氮除磷效果的影响.结果表明,在相同的进水COD浓度下,乙酸钠比葡萄糖更适合作为碳源,更能提高脱氮除磷效率.以葡萄糖为碳源时,COD为200 mg/L、C/N比为5、缺氧池与厌氧池进水配比为1∶2时,出水COD、TN、氨氮和TP浓度分别为28.5、10.8、2.1和0.5 mg/L,均达到国家一级A排放标准.若采用葡萄糖作为碳源,投加量以使进水C/N比为5～7.5为宜,外加碳源时缺氧池与厌氧池进水分配比可统一采用1∶1.     

厌氧法处理木薯淀粉废水的研究

采用厌氧法处理木薯淀粉废水,研究了厌氧反应器启动和运行的特性,以及温度和搅拌对厌氧生物降解的影响。结果表明:(1)COD去除率总体随着进水COD的增大而增大,在进水COD为9 983.38mg/L时,COD去除率最大,达到86.05%。(2)累计产甲烷量与进水COD呈正比关系,进水COD直接影响反应器的产甲烷量。(3)厌氧颗粒污泥活性最高的温度为30～35℃。(4)厌氧搅拌有利于提高厌氧颗粒污泥的产甲烷活性。     

厌氧颗粒污泥启动复合式厌氧折流板反应器的研究

研究以厌氧颗粒污泥接种的复合式厌氧折流板反应器(HABR)启动：在HABR中直接接种厌氧颗粒污泥,以退浆废水为试验进水,在系统水力停留时间为168 h,中温(32±1) ℃,进水pH值6.5～8,碱度适当偏高条件下,进入反应器废水COD浓度由1 800 mg/L逐渐提高到13 520 mg/L,运行60 d后系统COD去除率最低为45%,并且保持稳定,出水pH值和碱度相对比较稳定,污泥明显呈颗粒状,反应器启动完成。反应器可以在短时间内重新启动,污泥活性很快得到恢复。     

城市垃圾焚烧渗沥液中Ca2＋对厌氧EGSB处理效果的影响

研究了城市生活垃圾焚烧厂渗沥液中Ca2＋对厌氧颗粒污泥膨胀床反应器（EGSB）处理效果的影响,并采用静态实验方法考察了Ca2＋对厌氧颗粒污泥产甲烷活性的影响。实验结果表明,进水COD为17000mg／L的条件下,当Ca2＋浓度低于6000mg／L时,EGSB对COD去除率达93％以上;当Ca2＋浓度高于6000mg／L时,COD去除率随运行时间明显下降,并在污泥中形成大量沉淀。静态实验结果表明,废水中低浓度Ca2＋促进了厌氧颗粒污泥的产甲烷活性,但高浓度Ca2＋明显抑制了其产甲烷活性,这是导致高Ca2＋浓度条件下EGSB对COD去除率降低的主要原因。研究表明,颗粒污泥产甲烷活性恢复程度随Ca2＋浓度增加而减弱。     

常温下IC反应器启动过程中的颗粒污泥性能研究

在常温下用自配葡萄糖废水启动IC反应器,研究了厌氧颗粒污泥的形成过程和特性。IC反应器进水浓度为3 000 mg COD/L,水温为14.5～26℃,25 d内形成了颗粒污泥。结果表明,随着运行时间和容积负荷的增加,颗粒污泥粒径逐渐增大。反应器启动完成后,反应器中2 mm的颗粒污泥增加到6.6%,0.3 mm的颗粒从57.7%减少到39.4%;VSS浓度从24.7 g/L上升到48.2 g/L;VSS/SS从34.4%增加到72.8%。颗粒污泥的沉降速度与颗粒粒径成正比,0.3～3 mm的颗粒污泥的沉降速度介于34.05～109.75 m/h之间,具有良好的沉降性能。初始接种污泥几乎没有产甲烷活性,与第30 d的初期颗粒污泥相比,成熟的颗粒污泥的产甲烷活性提高了46.7%。     

UASB启动及不同浓度垃圾渗滤液的处理效果

在UASB反应器中接种好氧污泥培养厌氧颗粒污泥进行启动,研究不同浓度老龄(13年)垃圾渗滤液对处理效果的影响情况。通过保持进水COD浓度不变、逐步缩短HRT从而提高容积负荷到20 g COD/(L.d)的方法,可以培育出直径为1～3 mm颗粒污泥,最终产气量稳定在60～70 L/d,甲烷含量在50%～70%之间,COD去除率保持在90%左右,污泥层最底部MLSS为50 g/L。逐步提高进水中渗滤液的含量考察其对处理效果的影响,当进水为100%渗滤液时日产气量为500 mL/d、COD去除率仅为10%,表明渗滤液中多为难降解性有机物质。     

低COD浓度废水启动EGSB反应器

以厌氧活性污泥和好氧活性污泥接种于2个膨胀颗粒污泥床(EGSB)反应器中,进水流量为10 mL/min,回流量为180 mL/min,进水COD浓度在180 mg/L左右,有机负荷率(OLR)为1.728 kg COD/m3·d左右,污泥负荷率(SLR)为0.19 kg COD/kg MLSS·d左右,出水COD浓度维持在40mg/L左右,COD去除率达80%以上.控制温度在32～35 ℃,pH在6.8～7.2,反应器内氧化还原电位在-340 mV以下,水力停留时间(HRT)4.2 h,上升流速4.86 m/h以及加入80 mg/L絮凝剂(硫酸铝钾),缩短了启动时间,促进了颗粒污泥的形成.分别经过60 d和120 d运行,反应器启动成功.结果表明,上升流速、絮凝剂和污泥类型对颗粒污泥的形成有影响;接种好氧活性污泥在低浓度COD下,合理控制负荷速率能成功启动EGSB反应器.     

UASB处理硫酸盐有机废水的启动

为了考察上流式厌氧污泥床反应器(UASB)处理含硫酸盐有机废水的特性,采用有效容积为10 L的UASB,研究了启动运行过程中COD和SO2-4降解情况、出水VFA和pH值、产气量及颗粒污泥比产甲烷活性(SMA)变化状况。结果表明,接种厌氧颗粒污泥,保持进水COD为1 500 mg/L,SO2-4浓度为100 mg/L,将HRT由24 h缩短至12 h以提高负荷,经历55 d成功启动了UASB反应器;当HRT为12 h,进水COD和SO2-4负荷为3.0 kg/(m3·d)和0.20 kg/(m3·d),COD和SO2-4的去除率分别达到80%和89%,出水VFA为3 mmol/L,产气量达9.5 L/d,颗粒污泥的SMA为86.4 mL/(g VSS·d)。     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Spectrophotometric Determination of Atmospheric Acidity by means of the Displacement of the Equilibrium of Acid-Base Indicators

A method is described for determining acidity by means of the spectrophotometric determination of the displacement of the equilibrium of açid-base indicators. The method is simple, sensitive and free of known interferences. There is no dependence on costly or sophisticated equipment and the results obtained are reliable and reproducible.     

嗜盐菌的特性与高盐废水生物处理的进展

论述了嗜盐菌的形态特征、营养构成、生理特性和嗜盐机理，以及利用其特性在含盐有机废水处理中的应用，综述了国内外生化处理高含盐量有机工业废水的实验研究成果、在实际废水工程中的应用及其发展方向。对嗜盐菌的培养与驯化有一定的参考价值，对含盐废水处理工程的设计与运行有指导意义。