UV-TiO_2光催化氧化降解双酚A的动力学研究

采用自制光催化氧化反应器,研究了双酚A(BPA)在纳米TiO_2悬浆体系中的光催化氧化特性.结果表明:(1)UV-TiO_2对水中BPA有较强光催化氧化降解作用.在10 W低压汞灯照射下,当纳米TiO_2用量为1.0 g/L、pH为5.5、BPA初始质量浓度为10 mg/L、曝气量为4.0 mL/min、温度为室温、反应时间为120 min时,BPA去除率可达97.1%.当pH≥9.5时,120 min后BPA已经基本光催化氧化降解完全.(2)BPA的光催化氧化降解曲线均很好地符合一级反应动力学方程.其速率常数与纳米TiO_2用量、pH、BPA初始浓度、曝气量有关;促进·OH和电子-空穴对的生成是提高光催化氧化反应速率的重要途径.     

硫铁矿烧渣催化类Fenton法深度处理维生素C废水

采用硫铁矿烧渣协同Fe2+催化H2O2的类Fenton法深度处理维生素C制药废水,通过正交实验考察FeSO4投加量、H2O2投加量、搅拌反应时间、曝气时间等因素对低浓度难降解有机物去除的影响程度,并结合单因素实验确定最佳反应条件。结果表明:(1)正交实验中,各因素对催化氧化反应效果的影响程度依次为H2O2投加量搅拌反应时间曝气时间FeSO4投加量;(2)单因素实验中,最佳反应条件为烧渣投加量10g/L、H2O2投加量4.9mmol/L、FeSO4投加量3.9mmol/L、搅拌反应时间20min、曝气时间20min、絮凝沉淀部分聚丙烯酰胺(PAM)投加量5mg/L。在此条件下,COD去除率最高达63.21%。     

H_2O_2/Fe~0、H_2O_2/Fe~(2+)、H_2O_2/Fe~(3+)3种体系处理印染废水

采用H2O2/Fe0、H2O2/Fe2+、H2O2/Fe3+3种体系分别对印染废水进行处理,研究pH值、H2O2投加量、不同价态铁元素的投加量及反应时间对印染废水的COD和色度处理效果的影响。实验最佳的处理条件:H2O2/Fe0体系在pH为3.0,Fe0投加量为3.0 mmol/L,H2O2投加量为9.0 m L/L,反应时间为40 min时,COD去除率达到95.99%,色度去除率达到100%;H2O2/Fe3+体系在pH为3.0,Fe3+投加量为5.0 mmol/L,H2O2投加量为12.5 m L/L,反应时间为100 min时,COD去除率达到95.89%,色度去除率达到100%;H2O2/Fe2+体系在pH为3.0,Fe2+投加量为6.0 mmol/L,H2O2投加量为12.0m L/L,反应时间为100 min时,COD去除率达到95.85%,色度去除率达到100%。对比分析3种体系在各因素下的处理结果,H2O2/Fe0体系和H2O2/Fe3+体系都要优于H2O2/Fe2+体系,其中H2O2/Fe0体系的处理效果最好。     

印染RO浓水深度处理及回用

采用Fenton-石灰苏打法耦合工艺对某印染厂印染反渗透(RO)浓水进行深度处理。通过实验研究了不同H2O2和Fe2+投加量、p H和反应时间对废水COD去除率的影响,以及不同石灰和碳酸钠投加量对废水硬度的脱除效果,出水回用于染色工段进行染色实验。结果表明,在p H=3.0,Fe2+投加量为1.5 mmol/L,H2O2投加量为3.75 mmol/L,反应时间为45 min,石灰和碳酸钠投加量分别为450 mg/L和1 000 mg/L的条件下,出水COD和硬度的去除率可分别达到73.9%和85.0%,耦合工艺出水水质符合该厂回用染色水标准,且减少了盐的使用,可实现印染RO浓水回用。     

臭氧/活性炭联合工艺深度处理焦化废水

采用臭氧/活性炭联合工艺对焦化废水A2/O出水进行深度处理。考察了溶液初始pH值、臭氧投加量、活性炭投加量及使用次数、反应时间对焦化废水处理效果的影响。实验结果表明,活性炭的使用可显著提高臭氧对焦化废水COD的去除率,在溶液初始pH值为10.25、臭氧投加量为7.5 mg/min、活性炭投加量50 g/L、反应时间为30 min条件下,COD去除率达到73.51%。同时,在活性炭重复使用10次时,COD去除率为70.85%,仅降低了2.66%。     

絮凝-Fenton试剂氧化处理印染废水

采用Fenton试剂对某染袜厂2种印染废水(印染红和印染蓝)进行处理。考察了硫酸亚铁投加量、双氧水投加量、反应时间及pH值对印染废水的色度及COD去除率的影响,通过正交实验确定了Fenton试剂处理该废水的最佳操作条件为:反应时间30 min、双氧水(30%)投加量4 mL/L、硫酸亚铁投加量300 mg/L、pH值为4左右。在最佳条件下,印染蓝废水经氧化处理后COD去除率大于80%,色度去除率95%以上;印染红废水需经絮凝预处理后再用Fenton试剂氧化处理,其脱色率达到了99.6%,COD去除率为91.2%,出水COD浓度为96 mg/L,可达标排放。     

TiO2光催化-微滤膜分离深度净化亚甲基蓝印染废水

采用悬浮式TiO2光催化膜反应器深度净化纺织工业园区含亚甲基蓝印染废水经生物处理二级出水,利用中空纤维微滤膜进行催化剂截留分离,研究催化剂投加量、运行时间、溶解氧、搅拌方式对出水水质及膜通量的影响。结果表明:光催化会消耗体系溶解氧,鼓风曝气搅拌可同时为系统供氧,优于机械搅拌;该耦合体系的催化剂最佳投加量为1 g/L,经光催化氧化-膜组合工艺处理后水质优于GB 4287-1992《纺织染整工业污染物排放标准》的I级标准,符合建设部颁布的《生活杂用水水质标准》(CJ/T 48-1999)。     

混凝沉淀-Fenton-NaClO氧化深度处理垃圾渗滤液

用混凝沉淀-Fenton-NaClO氧化联合深度处理垃圾渗滤液,利用单因素变量法得出:混凝实验在PFS投加量为1.2g/L、pH=6、搅拌时间为30min的条件下进行,COD、氨氮和色度的去除率分别达到56.60%、15.62%和56.52%;混凝出水在初始pH为4、H2O2投加量为80mmol/L、n(H2O2)∶n(F2+)比为1∶1、反应时间为60min的条件下进行Fenton氧化,COD、氨氮和色度的去除率分别达到71.38%、21.43%和95.24%;Fenton氧化出水在pH为6、NaClO投加量为60mmol/L、反应时间为60min的条件下进行NaClO氧化,COD和氨氮去除率分别为83.42%和99.57%;联合工艺COD、氨氮和色度去除率分别为96.68%、99.69%和98.04%,出水浓度分别为63mg/L、0.47mg/L和18倍,均可满足《生活垃圾填埋污染控制标准(GB16889-2008)》中规定的排放标准。     

微米级负载型TiO_2催化剂在光催化-膜分离反应器中的应用

基于光催化-膜分离三相流化床反应器的结构特点及膜分离特性,以微米级MCM-41分子筛为载体,采用原位生成法制备微米级负载型TiO2催化剂。针对微米级负载型TiO2催化剂在光催化-膜分离反应器中的分布特性、悬浮特性、分离特性及膜污染特性进行研究。结果表明,曝气量一定的情况下,微米级负载型TiO2催化剂在光催化-膜分离反应器中具有良好的悬浮特性,且优于纳米TiO2。随着催化剂投加量的增加,悬浮浓度也随之增加。光催化反应器底部曝气0.3m3/h、催化剂投加量为1 g/L时为宜。膜分离器中催化剂悬浮浓度明显低于光催化反应器;该微米级催化剂与纳米TiO2相比具有不粘附、不堵塞膜孔等优良特性,能够有效降低膜污染,延长分离膜使用寿命。膜底曝气为0.1 m3/h时,反应器连续运行5 h(未加反冲洗)后,微米级负载型TiO2催化剂和纳米TiO2对膜组件的污染程度分别为膜通量衰减率4.3%和37.4%。反应器连续运行72 h,膜组件依然具有很好的分离特性。     

零价铁Fenton技术处理含聚乙烯醇的印染退浆废水

采用零价铁Fenton技术处理含聚乙烯醇(PVA)的印染退浆废水。通过单因素实验和正交实验,考察了初始pH、H2O2投加量、铁屑粒径及投加量和反应时间对实验结果的影响。结果表明,初始pH和H2O2投加量对处理效果影响很大。最佳反应条件是初始pH=4.0,H2O2投加量为100mmol/L,铁屑(粒径为1~3mm)投加量为15g/L,反应时间为30min。在该条件下,出水PVA质量浓度为0.9mg/L,PVA去除率为99.9%,COD去除率为23.6%,BOD5/COD由0.12升高至0.34,可生化性明显提高。无论从处理效果考虑还是从成本考虑,零价铁Fenton技术都优于传统Fenton技术。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.