丙烯酸装置废水特征有机污染物及其荧光特性

采用吹扫捕集-气相色谱/质谱法(P&T-GC/MS),液液萃取-气相色谱/质谱法(LLE-GC/MS)等方法对丙烯酸装置废水中主要特征有机污染物进行了定性、定量分析,研究了废水和各主要特征污染物的三维荧光特性。结果表明,废水中共检出有机酸、苯系物、酯、醛、醇等24种有机污染物,其中含量较大的有乙酸55.13%,丙烯酸23%,甲醛21.81%,甲苯0.03%,4-羟基-2-丁酮0.02%,丙烯酸甲酯0.01%,正丁醇0.01%。丙烯酸废水中含有3个荧光峰,区域IV内的荧光峰(λex/em=290/355 nm)主要由废水中高浓度的丙烯酸产生,区域V内的2个荧光峰(λex/em=390/495 nm,λex/em=295/480 nm)由水中的腐殖质产生。丙烯酸抑制了甲苯、甲醛、乙酸等3种荧光物质对丙烯酸废水荧光强度的贡献。4种荧光物质的荧光基团影响力大小:碳碳双键+羧基> 苯环> 羰基> 羧基。     

采用水解酸化-复合好氧处理制药工业废水的工艺评价

以制药工业综合废水处理为例对其采用的两级水解酸化复合好氧工艺的处理效果进行评估。按常规指标进行评估,该工艺对于制药综合废水的处理效果达到了设计目的,COD去除率可达到78.2%以上,NH+4-N的去除率达到99.3%,出水质量基本满足"污水综合排放标准(GB8978-1996)"二级标准和"辽宁省污水综合排放标准(DB21.1627-2008)";急性毒性的检测表明,经过该工艺处理后出水为低毒性;三维荧光谱分析(EEM)表明,制药综合废水经生物处理后的可溶性有机物中仍然存在难降解物质,建议增加物化处理以提高处理效果;并且制药废水经处理后的出水中的盐度对排入的生态系统存在风险,建议纳入排放标准以加强管理。     

水解酸化-厌氧-好氧法处理NF合成制药废水研究

研究了序批式水解酸化 厌氧 好氧生物处理工艺对NF合成制药废水的处理。由于NF制药废水中含有大量有毒有机化合物 ,在生物处理过程中这些有毒物质会抑制活性污泥的活性 ,因此需经过适当稀释原水以达到处理单元可接受的毒性范围。采用BODTrack快速测定了不同原水稀释条件下活性污泥呼吸曲线第一段斜率的变化 ,结果表明 ,当原水稀释 2 0倍以上后 ,对活性污泥的活性没有明显的抑制。通过批量实验 ,优化了工艺的运行条件 ,并进行了小试的连续运行。采用本工艺可以达到NF制药废水COD的稳定高效去除 ,结果显示 ,COD的去除率可达 76 %。     

厌氧-好氧生化处理淀粉废水的工程应用

通过邳州市奋达淀粉有限公司的工程实例,介绍了厌氧-好氧生化处理工艺在处理淀粉生产废水中的应用.该工艺具有处理设施运行稳定,处理效果好的优点,系统出水水质满足《污水排放标准》一级标准要求.     

水解酸化-改良UASB工艺处理玉米酒精废水

采用一种新的工艺技术方法即水解酸化-改良UASB工艺处理玉米酒精废水。结果表明,在改良UASB运行60 d顺利启动完成后,进水COD在5 470～7 910 mg/L之间,TN在70～107 mg/L之间,TP在115～187 mg/L之间,SS在864～1 490 mg/L之间的条件下,水解酸化对COD和SS的去除率分别达50%和51%,NH3-N经过水解酸化后升高。改良UASB对COD的去除率达80%,对NH3-N、TN和TP也有一定去除,去除率分别为12%、17%和20%,经过水解酸化及改良UASB处理利于后续好氧处理。     

焦化厂A/O出水中的有机污染物分析

采用色谱－质谱（GC／MS）联用仪分析和鉴定了上海宝钢焦化厂A／O生化阶段出水的有机污染物组成,共检出各类有机污染物70多种。结合焦化废水专用混凝剂的混凝处理实验结果,指出了各类有机污染物的去除情况。     

混凝-水解酸化-好氧-混凝工艺处理印染废水

采用“混凝-水解酸化-好氧-混凝”工艺处理印染废水,当进水COD为800—1200mg／L时,出水可达到国家《污水综合排放标准》（GB1978--1996）,其中COD指标甚至达到江苏地方标准《太湖地区城镇污水处理厂及重点工业行业主要水污染物排放限值》（DB32／T1072--2007）。     

水解酸化-缺氧法处理采油废水的污染物迁移降解试验研究

水解酸化-缺氧法对采油废水有较好的处理效果,采用GC/MS技术对水解酸化-缺氧法处理采油废水过程中污染物的迁移降解进行的研究表明:水解酸化段和缺氧段对采油废水中碳原子为C6～C9、分子量为100～140的有机物均有较好的降解能力.其中,在水解酸化段中酮类、芳烃得到较好的降解,缺氧段中酚类和醚类化合物降解明显.水解酸化-缺氧工艺对于采油废水中的甲苯和二甲苯具有较好的降解能力.     

水解酸化-厌氧-好氧法处理NF合成制药废水研究

研究了序批式水解酸化-厌氧-好氧生物处理工艺对NF合成制药废水的处理。由于NF制药废水中含有大量有毒有机化合物，在生物处理过程中这些有毒物质会抑制活性污泥的活性，因此需经过适当稀释原水以达到处理单元可接受的毒性范围。采用BOD Track快速测定了不同原水稀释条件下活性污泥呼吸曲线第一段斜率的变化，结果表明，当原水稀释20倍以上后，对活性污泥的活性没有明显的抑制。通过批量实验，优化了工艺的运行条件，并进行了小试的连续运行。采用本工艺可以达到NF制药废水COD的稳定高效去除，结果显示，COD的去除率可达76％。     

水解酸化-铁炭微电解-好氧生化工艺处理印染废水

采用水解酸化-铁炭微电解-好氧生化工艺对印染废水进行了处理.COD为3 000～4 000 mg/L、BOD5为750～1 000 mg/L、色度为500～600倍、NH3-N为30～40 mg/L、SS为200～300 mg/L、pH为6～10的印染废水,经该工艺处理,后出水达到了<纺织染整工业水污染物排放标准>(GB 4287-92)的一级标准.运行结果表明,该工艺具有运行稳定、管理简单等优点.     

气相色谱/质谱测定苯酚丙酮生产废水中半挥发性有机物

建立了用二氯甲烷液液萃取对苯酚丙酮生产废水进行预处理,气相色谱/质谱法同时测定废水中半挥发性有毒有机物异丁酸、异丙苯、α-甲基苯乙烯、2-苯基丙醛、苯乙酮、2-苯基-2-丙醇、α-甲基苯甲醇、苯酚和苯甲酸等的定性定量分析方法。色谱条件为:DB-17MS型色谱柱,程序升温,进样量为1μL,质量选择检测器(MSD)。实验结果表明,该色谱条件对苯酚丙酮生产废水中各半挥发性组分具有较好的分离效果。而对9种组分的最低检出限均低于0.04mg/L,精密度实验相对标准偏差2.14%～5.15%,实际水样的加标回收率稳定。苯酚丙酮生产废水中的主要污染物为2-苯基-2-丙醇,其次为苯酚、异丁酸和异丙苯。     

煤气废水中有机化合物的生物去除特征

好氧/缺氧/好氧生物处理系统是一种新型煤气废水二级处理工艺,该工艺通过改变微生物的生化环境,充分发挥各单元对有机化合物的降解功能,强化了有机化合物总体去除效果.主要采用气相色谱/质谱联用(GC/MS)测试方法,分析对比煤气废水进水及其系统各单元出水中有机化合物的成分,结合生物降解的特点,评价各单元对有机化合物的去除效果...     

制药废水有机污染物的微生物降解

以宜昌某制药废水为惟一碳源,通过选择性富集、驯化培养和划线分离纯化,分别从三峡大学求索溪、三峡某药业及三峡大学接待中心3种活性污泥中分离得到菌株HS150,其中三峡大学求索溪的活性污泥中菌株HS150含量最大,其降解能力最强。经革兰氏染色、氧化酶实验、触酶实验及DNA酶实验等,初步鉴定菌株HS150为奈瑟氏菌属(Neisseria)。由单因子优化法实验得出菌株HS150降解宜昌某制药废水的最适条件：温度为30℃,pH为7,当底物浓度为600 mL/L时,制药废水降解率可达85%,其矿化程度较高。     

The fate of dissolved organic carbon (DOC) in the wastewater treatment process and its importance in the removal of wastewater contaminants

Goal, Scope and Background Dissolved organic carbon (DOC) constitutes a parameter of organic pollution for waters and wastewaters, which is not so often studied, and it is not yet regulated by directives. The term ‘DOC’ is used for the fraction of organics that pass through a 0.45 μm pores’ size membrane. The type of wastewater plays an important role in the quality of DOC and it has been shown that DOC may contain aquatic humic substances, hydrophobic bases, hydrophobic neutrals, hydrophilic acids, hydrophilic bases and hydrophilic neutrals. The quality of the DOC is expected to affect its fate in a wastewater treatment plant (WWTP), since a considerable fraction of DOC is not biodegradable, and it may be released in the aquatic environment together with the treated effluent. In the present study, the occurrence of DOC during the wastewater treatment process is investigated and its removal rates during primary, secondary and overall treatment are being estimated. Furthermore, a correlation is being attempted between DOC and the concentrations of selected Persistent Organic Pollutants (POPs) and Heavy Metals (HMs) in the dissolved phase of wastewaters, to examine whether there are common sources for these pollution parameters in WWTPs. Also, DOC is being correlated with the partition coefficients of the above-mentioned pollutants in wastewater, in order to examine the effect of ‘solubility enhancement’ in WWTPs and to evaluate the result of this phenomenon in the efficiency of a WWTP to remove organic pollutants. Methods For the purposes of this study, 24-h composite wastewater samples were collected from the influent (raw wastewater, RW), the effluent of primary sedimentation tank (primary sedimentation effluent, PSE) and the effluent of secondary sedimentation tank (secondary sedimentation effluent, SSE). Samples were analyzed for the presence of 26 POPs (7 PCBs and 19 organochlorine pesticides), 8 HMs and DOC. Results and Discussion Mean concentrations of DOC in RW and PSE were at similar levels (∼ 70 mg l⁻¹), suggesting that primary treatment has a minor effect on the DOC content of wastewater. DOC concentrations in SSE were significantly lower (∼ 19 mg l⁻¹) as a result of the degradation of organic compounds in the biological reactor. Calculated removals of DOC were 0.8% in the primary treatment, 63% in the secondary treatment, and 69% in the overall treatment, exhibiting large differences from other organic pollution parameters, such as BOD and COD. The overall DOC removal was found to be independent from the DOC concentration in raw wastewater. Poor correlation was also observed between the DOC content and the concentrations of wastewater contaminants, such as persistent organic pollutants (POPs) and heavy metals (HMs), probably suggesting that their occurrence in WWTPs is due to different sources. A good negative linear relationship was revealed between DOC concentrations and the logarithms of the distribution coefficients (K _d) of various POPs and HMs between the solid and the liquid phases of wastewater. This relationship suggests that DOC facilitates hydrophobic pollutants to remain in the dissolved phase thus causing lower removal percentages during the treatment process. Conclusion DOC was measured at three stages of a municipal WWTP that receives mainly domestic wastewater and urban runoff. DOC concentrations in untreated and primarily treated wastewater were almost equal, and only after the secondary sedimentation there was a decrease. Concentrations and removal rates of DOC were in the same levels as in other WWTPs that receive municipal wastewater. The origin of DOC was found to be different to the one of POPs and of HMs, as no correlation was observed between the concentrations of DOC and the concentrations of these pollutants. On the contrary, DOC was found to have significant negative correlation with the K _d of all pollutants examined, suggesting that it plays an important role in the partitioning of those pollutants between the dissolved and the sorbed phase of wastewaters. This effect of DOC on partitioning can affect the ability of WWTPs to remove toxic pollutants, and that way it facilitates the discharge of those chemicals in the aquatic ecosystems together with the treated effluent. Recommendation By the results of this work it is shown that the presence of DOC in wastewaters can significantly affect the partition of hazardous pollutants between the dissolved and the sorbed phase. It is therefore of importance that this parameter is controlled more in wastewaters, since it can cause a decrease in the efficiency of WWTPs to remove quantitatively persistent pollutants.     

瓜环对污水厂二级处理出水中有机污染物的混凝性能

采用扫描电子显微镜和傅里叶红外光谱技术考察了瓜环的物化性能,以及溶液pH和瓜环投加量对其混凝效果的影响。结果表明,盐酸对瓜环的助溶效果最佳,混凝后絮体颗粒呈密实的团状。红外光谱中无新吸收峰出现,说明瓜环与污水中有机物的混凝去除以物理作用为主,无化学键的形成。当投药量大于400 mg/L时,瓜环对初始有机物浓度为6.0 mg/L和9.2 mg/L的污水厂二级处理出水的TOC去除率分别在20%和25%以上。与明矾和聚合氯化铝等传统混凝剂相比,瓜环的混凝性能明显优于传统混凝剂且受pH值的影响较小,作为新型水处理材料具有一定的研究价值和应用前景。     

强化EGSB-好氧组合工艺处理马铃薯淀粉废水研究

马铃薯淀粉废水具有处理难度大、有机污染物浓度高等特点,属于高难度有机废水。为了有效的解决马铃薯淀粉废水造成的环境污染问题,采用强化厌氧膨胀颗粒污泥床组合好氧工艺对有机污染物质和氨氮的去除效能进行研究。研究结果表明-强化厌氧膨胀颗粒污泥床在最佳运行工况条件下(进水温度为30℃、外回流比为2和水力停留时间24 h),组合工艺出水COD质量浓度和氨氮浓度分别在92.35 mg/L和10.28 mg/L左右,去除率分别在98.85%和86.29%左右,出水水质能够满足《污水综合排放标准》(GB8978—1996)二级标准,说明该工艺是一种适用于马铃薯淀粉废水的处理技术。     

淀粉废水处理工艺选择

针对淀粉废水的特性 ,通过大量实验 ,提出合理的处理工艺 ,在实际运行中取得了较好的处理效果 ,节省了占地和建设投资     

活性炭催化臭氧氧化深度处理工艺对酵母发酵废水中有机物的去除特性分析

酵母发酵废水经过厌氧膨胀颗粒污泥床（EGSB）-好氧膜生物反应器（MBR）组合工艺处理后,仍含有较高浓度的COD,不能满足排放要求。以发酵废水处理过程中MBR处理单元的出水为研究对象,选择活性炭催化臭氧氧化作为其深度处理工艺,以活性炭吸附和单独臭氧氧化工艺作为对比,重点考察了活性炭催化臭氧氧化深度处理工艺对发酵废水中有机物的去除效能,并借助红外光谱、三维荧光光谱和气相色谱-质谱联用等方法,详细分析了发酵废水深度处理过程中有机物的变化规律。研究结果表明,活性炭催化臭氧氧化深度处理工艺对发酵废水中的芳香族化合物、具有共轭双键的有机物及色度具有良好的去除效果;并且对废水中酸类、醇类和醛类等有机物有较好的降解、转化和去除效果。此外,活性炭催化臭氧氧化工艺还可以使以烷烃、卤代烃、醇类、酯类和酮类为主的大分子有机物的含量大幅度减少。