挥发性脂肪酸对厌氧干式发酵产甲烷的影响

为了提高中温干式厌氧间歇发酵效率,研究了发酵过程中间产物———挥发性脂肪酸对产甲烷的影响。实验分2批进行,第1批在牛粪发酵过程中分别添加乙酸、丙酸和丁酸,第2批发酵添加易产生挥发酸的厨余垃圾混合发酵。结果显示,添加单一挥发酸的发酵过程中,添加丙酸的产甲烷速度较慢,因为丙酸降解生成乙酸的速度较慢,减慢了甲烷的形成;混合发酵过程厨余垃圾产甲烷速度比牛粪快,发酵过程产生2个产气高峰;牛粪和厨余垃圾固体物质含量比在11∶1到5∶1范围内较好,比牛粪单独发酵产气多,产酸高但不酸败,产生的挥发酸主要是乙酸和丙酸,其中比例为7∶1混合发酵的产甲烷速率最大,为4.89 mL/(g VS·d)。实验表明,牛粪厌氧干式发酵过程添加一定量的厨余垃圾可加快挥发酸的产生并提高挥发酸产量,从而提高甲烷的产量,但是总挥发酸长时间超过10 000 mg/L,pH降到不适于产甲烷菌生长的范围时,将抑制甲烷的生成,挥发酸积累导致厌氧发酵酸败。     

酸化相发酵类型对甲烷相产甲烷性能的影响

以餐厨垃圾和稻草为原料,通过调节酸化相的pH、氧化还原电位(ORP)和进料负荷(OLR),对酸化相的产酸发酵类型和不同酸化类型的产甲烷性能进行了研究。结果表明:当酸化相的pH4.5和ORP-120 m V的条件下,发酵类型为乙醇型;当酸化相的pH5.5时,发酵类型为丁酸型发酵;在乙醇型发酵和丁酸型发酵相互转换的过程中,会出现混合型发酵。从酸化效果方面来看,丁酸型发酵的产酸性能最优,酸化度为36%。同时,丁酸型发酵酸化产物的产甲烷性能最好,累计甲烷产率为535 m L·g-1VS。通过PCR-DGGE的微生物菌群鉴定结果可知,在两相厌氧消化过程中,酸化相中的优势菌种主要以拟杆菌属(Bacteroidetes)和乳酸杆菌属(Lactobacillus)为主,甲烷相中的优势菌种以乳酸杆菌属(Lactobacillus)为主。     

浮萍与奶牛粪混合厌氧干发酵研究

对浮萍和奶牛粪为发酵原料在中温条件下进行了半连续厌氧干发酵实验,研究物料配比对发酵过程的影响。实验设置奶牛粪与浮萍配比(质量比)分别为1.00∶0.33、1.00∶0.50、1.00∶0.67和1.00∶1.00,水力停留时间(HRT)均采用30d。结果表明,在HRT为30d条件下,奶牛粪与浮萍配比为1.00∶0.67时产气情况最佳,容积产气率和原料产气率(以挥发性固体(VS)计)分别为0.50L/(L·d)和0.33L/g。     

厌氧发酵方式对乳渣废水产酸性能的影响

为了研究厌氧发酵方式对乳渣废水发酵产酸效果的影响,分别对乳渣废水采用自然型发酵、填料型发酵及中性型发酵(pH=7.0±0.2),并进行连续2个周期的厌氧反应。分析乳渣废水中可溶性化学需氧量(SCOD)、蛋白质、多糖、挥发性短链脂肪酸(SCFAs)、水解酶(蛋白酶、α-葡萄苷酶)和辅酶420、NH_4~+-N及PO3-4-P指标的变化。研究发现,中性产酸系统中水解酶活性较高,蛋白质和多糖等物质水解性能较好,使乳渣废水产酸性能最佳,最大SCFAs积累量为12 328.37 mgCOD·L~(-1)。自然发酵产酸系统中水解酶活性最低,系统中残留大量的蛋白质和多糖等物质,最低SCFAs积累量为4322.61 mg COD·L~(-1)。同时发现,3个发酵系统中挥发性短链脂肪酸酸成分具有显著差别,其中自然型发酵系统乙酸积累率最大,可达69.70%,中性发酵系统丙酸积累率最大可达49.27%,填料型发酵系统正丁酸积累率最大可达38.85%。     

进出料频率对牛粪两相厌氧发酵特性的影响

以牛粪为发酵原料,在中温(35±2)℃的条件下,采用自行设计的两相厌氧发酵中试装置,在水力停留时间确定的前提下,酸化原料分别以每天、间隔1 d和间隔2 d 3种不同进出料频率加入产甲烷罐,观察挥发性固体(VS)产气率和甲烷含量的变化情况。实验结果表明:保持产酸相与产甲烷相水力停留时间(HRT)分别为3 d和17 d,每天进出料产气效果最佳,原料VS产气率和甲烷含量最大值分别为0.29 m3/(kg·VS)和58.36%。     

牛粪和玉米秸秆厌氧消化产甲烷潜力及动力学

为了评价牛粪和玉米秸秆的产甲烷潜力,研究其厌氧消化过程动力学方程,采用自制序批式厌氧发酵实验装置对某养殖场牛粪和秸秆的最大甲烷生产潜力及其发酵过程进行研究。通过实验研究,测得接种物、牛粪和玉米秸秆的累计甲烷产量分别为64.87、244.0和466.54 m L CH4/g VS。根据实测的产气量变化曲线,按照modified Gompertz equation模型进行方程拟合,牛粪组和玉米秸秆组拟合方程的相关性系数分别为0.983和0.991,表明运用modified Gompertz equation模型预测牛粪和玉米秸秆的产甲烷潜力方法可行。通过对产甲烷过程的动力学研究得到:接种物、牛粪和玉米秸秆的最大产甲烷潜力分别为66.07、213.93和458.57 m L CH4/g VS,与实测值的误差率分别为1.8%、12.3%和1.7%;牛粪和玉米秸秆的最大甲烷日产气率(Rm)和延滞期时间(λ)分别是13.14 m L CH4/(g VS·d)、30.76 m L CH4/(g VS·d)和0.35 d、0.71 d。综上,玉米秸秆厌氧消化的停滞期长,但总产气量和最大甲烷日产期率都比牛粪高。     

蓝藻定向发酵产丁酸的条件研究

以4种有机酸(乳酸、乙酸、丙酸、丁酸)对厌氧颗粒污泥进行胁迫处理,将胁迫后的污泥接种太湖蓝藻进行发酵产丁酸的实验,考察单一有机酸及混合有机酸胁迫对提高蓝藻厌氧发酵产丁酸的影响.结果表明,采用乳酸浓度2 g/L、乙酸浓度6 g/L、丙酸浓度5 g/L和丁酸浓度12 g/L的混合有机酸胁迫污泥后产丁酸效果最佳,获得的最大丁...     

金属离子强化餐厨垃圾高温厌氧发酵产酸

以经过高温驯化的污泥作为厌氧微生物,以餐厨垃圾作为发酵基质,向发酵体系中加入不同浓度Fe~(2+)、Mg~(2+)和Ni~(2+)进行单因素实验。实验结果表明:当Fe~(2+)、Mg~(2+)和Ni~(2+)加入量分别为800、250和0.50 mg/L时,挥发性脂肪酸(VFA)的产量最大,分别为23.58、22.38和23.08 g/L;加入不同浓度Fe~(2+)、Mg~(2+)和Ni~(2+)的厌氧发酵液相产物中丁酸含量均最高,但在一定浓度范围内随着金属离子的添加,发酵产物中丁酸所占的比例逐渐减小,乙酸所占比例逐渐增加;加入适量金属离子在一定程度上能够抑制发酵液中氨氮的溶出。     

基质组分对厨余与污泥共发酵动力学特性的影响

通过厌氧发酵4阶段动力学实验、产甲烷抑制实验及单一VFA的产甲烷动力学实验,探明了厨余和污泥共发酵过程中,典型组分对其潜在的酸积累类型以及甲烷化过程的影响。结果表明,不同基质组分在厌氧发酵过程中的VFA组成比例以及单一VFA的产甲烷化动力学特性,对其产甲烷潜能及速率有着决定性影响。乙酸的甲烷化速率高达44.80 mL·d~(-1),丁酸略慢于乙酸,而丙酸和戊酸的甲烷化速率不足乙酸的1/2,其中丙酸的延滞期长达1.76 d。因此,产酸类型以乙酸为主的污泥、菜类在产甲烷阶段不存在延滞期;而蛋肉类及油的产甲烷速率受到丙酸、戊酸动力学特性的影响相对较慢。通过调整共发酵基质配比不仅能够提高发酵潜能,还能够优化VFA组成比例,实现较高的甲烷产率及甲烷化速率。     

微氧条件下玉米秸秆的发酵产氢

以玉米秸秆为原料,通过小试实验研究了不同的预处理方式和通氧量对微氧条件下发酵产氢的影响,放大实验对比了微氧发酵和厌氧发酵过程中产气、产氢、pH、碱度、挥发性脂肪酸(VFA)以及微生物种群的变化。小试实验表明,经过稀酸预处理的玉米秸秆产氢效果最好,最佳通氧量确定为280mL/(kg·d)。放大实验表明,微氧发酵的最大产气量、最大产氢量、累计产气量和累计产氢量均高于厌氧发酵,并且产气和产氢时间延长了6h。引起pH和碱度变化的原因主要是VFA的积累,特别是乙酸和丁酸。能够鉴定到科及以下的微氧发酵产氢优势种有肠球菌属(Enterococcus sp.)、拟杆菌属(Bacteroides oleiciplenus)、柠檬酸杆菌属(Citrobacter sp.)、消化链球菌科(Peptoclostridium difficile)、肠杆菌属(Escherichia sp.)、乳杆菌属(Lactobacillus mucosae)、梭状芽孢杆菌科(Clostridia)、梭菌属(Clostridium baratii)、双歧杆菌属(Bifidobacterium animalis)。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

Visualisation of the complexity of EUSES

The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters (inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation, on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency. The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters), and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity to 961, and the maximal dimension is 21.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

产油微藻培养与回收的关键技术研究进展

寻找廉价而高效的替代原料是实现生物柴油产业化的关键所在.微藻以含油量高、生长周期短、环境适应能力强、生物产量高等优点,有望成为一种极具潜力的生物柴油生产原料.然而,目前尚存在微藻培养低效成本高和微藻回收效率低两大难题.综述了微藻培养与回收过程中的关键技术,并对存在的两大难题及其改进技术进行了详细的探讨.最后,总结并展望了微藻培养、回收技术未来的发展趋势.     

红土吸附砷对其动电电位的影响

研究了遵义红土吸附砷对其动电电位的影响 ,从砷酸根浓度和体系pH对红土动电电位影响的角度作了探讨 ,结果表明 ,砷酸根离子浓度越大 ,Zata电位下降幅度越大 ,Zata电位也越低 ;随着体系pH的升高 ,氧化铁胶体动电电位逐渐下降 ,甚至改变了表面电位的符号。由此得出了红土吸附砷属于专性吸附的结论。