PACS的结构特征及絮凝性能研究

制备了碱化度及Ａｌ＾３＋／ＳＯ＾２－４摩尔比不同的系列ＰＡＣＳ，分别进行常压（干燥温度１０５℃）及真空干燥（真空度为－０．０９８ＭＰａ、干燥温度６５℃）制备固体产品。用红外光谱及Ｘ－射线衍射谱研究了碱化度、Ａｌ＾３＋／ＳＯ＾２－４摩尔比、干燥温度对ＰＡＣＳ的结构影响，比较了干燥温度不同对ＰＡＣＳ固体样品的溶解度及絮凝效果的影响，借助于显微电泳测定技术研究不同碱化度及不同Ａｌ＾３＋／ＳＯ＾２－４摩尔     

Al—Ferron逐时络合比色法研究PACS中铝的水解聚合形态

制备了碱化度及不同Ａｌ＾３＋／ＳＯ＾２＝４摩尔比的系列ＰＡＣＳ，用Ａｌ－Ｆｅｒｒｏｎ逐时络合比色法研究了铝的形态分布，考察了碱化度，Ａｌ＾３＝／ＳＯ＾２＝４摩尔比，稀释作用及ｐＨ值对铝的形态分布的影响。     

聚硅氯化铝（PASC）的形态分布及转化规律：Ⅱ.^27Al—NMR法研究PASC溶 …

采用＾２７Ａｌ－ＮＭＲ法比较研究了ＰＡＳＣ与ＰＡＣ中铝的形态分布。实验结果表明,在ＰＡＳＣ中,由于聚硅酸与铝水解聚合物产物间的相互作用,使得铝的水解聚合形态分布及转化情况发生了变化。在相同Ｂ值条件下,ＰＡＳＣ中Ａｌ单和Ａｌ１３的含量低于ＰＡＣ中相应Ａｌ单和Ａｌ１３的含量,而ＰＡＳＣ中Ａｌ其它的含量大于ＰＡＣ中Ａｌ其它的含量,其差值随着碱化度（Ｂ）和Ａｌ／Ｓｉ摩尔比的减小而增大。     

大气中PAN的测定及其与前体物的关系

对北京中关村地区大气ＰＡＮ的监测结果表明：在强日照条件下，ＰＡＮ浓度随汽车等排放和ＮＯ２浓度的增加而增加，高ＰＡＮ浓度水平与高Ｏ３浓度相关联；夏季的ＰＡＮ浓度明显高于春季。模拟实验的结果证实：Ｃ３Ｈ６是大气中重要的ＰＡＮ前体物，在一定范围内，其浓度越高，ＰＡＮ浓度越大；Ｃ２Ｈ４生成ＰＡＮ是困难的，Ｈ２Ｏ２的存在对Ｃ２Ｈ４反应生成ＰＡＮ有促进作用；大气中ＳＯ２的存在可降低ＰＡＮ的生成速率。在〈４００     

聚合氯化铝与有机机高分子复合絮凝剂的电荷特性及其絮凝作用

用流动电流技术研究了聚合氯化铝与不同类型有机高分子复合絮凝剂的电荷特性。并用ζ电位分析仪结合混凝烧杯实验研究了不同碱化度（Ｂ）的ＰＡＣ与阳离子型有机高分子Ｃ１０９Ｐ复合絮凝剂的电中和水体颗粒物的能力与絮凝效能的关系。     

聚合氯化铝铁絮凝剂的性能研究

煤矸石是采煤过程之废料。本文利用煤矸石制备出了聚合氯化铝铁（ＰＡＦＣ）：一种新型无机高分子絮凝剂，探讨了Ｆｅ＾３＋的稳定性与溶液离子强度之间的关系，发现溶液的离子强度越大，则产生Ｆｅ（ＯＨ）３沉淀时的ＰＨ越高。研究了ＰＡＦＣ水解产物的ζ电位及絮凝效果随ＰＨ的变化情况，比较了ＰＡＦＣ、ＰＡＣ和ＰＦＳ的除浊性能，ＰＡＦＣ在ＰＨ为７．０－８．２范围内除浊效果最佳，ＰＡＦＣ的除浊效果优于ＰＡＣ。     

合成工艺条件对A1－Ferron反应动力学特征及Al（Ⅲ）形态分布的影响

通过Al-Ferron络合比色动力学分析，对Al(Ⅲ)的形态进行了较为准确的划分和计算，考察了工艺条件对动力学参数和铝形态分布的影响．研究表明，铝的初始浓度、合成温度对Alh与Ferron的解离-络合反应的速率常数kb有一定的影响，而碱化度、合成时的搅拌强度和加碱速度对kb的影响不大；碱化度、铝的初始浓度对铝的形态分布影响很大，搅拌强度、合成温度和加碱速度对铝的形态分布也有一定的影响。     

聚硅氯化铝（PASC）的形态分布及转化规律：Ⅲ.Al—Ferron逐时络合比？…

本文对Ａｌ－Ｆｅｒｒｏｎ逐时络合比色法和＾２７Ａｌ－ＮＭＲ法对ＰＡＳＣ和ＰＡＣ中铝的形态分布测定结果进行了对比分析的讨论。结果表明。在ＰＡＣ中,Ａｌ１３和Ａｌｂｈ之间具有良好的对应关系。Ａｌ１３／Ａｌｂ比值为１．０左右。但对ＰＡＳＣ而言,情况有所不同,在低碱化度（Ｂ）和低Ａｌ／Ｓｉ摩尔比情况下,Ａｌ１３和Ａｌｂ之间的不存在对应关系,Ａｌ１３和Ａｌｂ比值远远小于１．０,随着Ｂ值和Ａｌ／Ｓｉ摩尔比的升     

絮凝剂PAN-DCD与甲基橙相互作用中的热力学研究

用平衡渗析法研究了有机高分子絮凝剂ＰＡＮ－ＤＣＤ与甲基橙（ＭＯ）在２０,２５,３０,３５℃下相互作用的热力学,求得结合常数Ｋ和热力学参数△Ｇ,△Ｈ,△Ｓ,在对不同絮凝剂结构进行表征的基础上,探讨了不同ＰＡＮ,ＤＣＤ配比对合成的絮凝剂与ＭＯ相互作用的影响,结果表明：ＰＡＮ－ＤＣＤ与ＭＯ的相互作用中能量作用是主要的：随ＰＡＮ与ＤＣＤ的比值增大,合成的絮凝剂ＰＤ１,ＰＤ２,ＰＤ３在常温下与ＭＯ的结合程试     

合成工艺条件对Al-Ferron反应动力学特征及Al(Ⅲ)形态分布的影响

通过Al Ferron络合比色动力学分析 ,对Al(Ⅲ )的形态进行了较为准确的划分和计算 ,考察了工艺条件对动力学参数和铝形态分布的影响 .研究表明 ,铝的初始浓度、合成温度对Alb 与Ferron的解离 络合反应的速率常数kb 有一定的影响 ,而碱化度、合成时的搅拌强度和加碱速度对kb 的影响不大 ;碱化度、铝的初始浓度对铝的形态分布影响很大 ,搅拌强度、合成温度和加碱速度对铝的形态分布也有一定的影响 .     

固固共混法制备聚合氯化铝混凝剂

采用固固共混法,制备具有不同铝浓度和碱化度（B）的聚合氯化铝（PAC）混凝剂．实验结果表明,在高铝浓度下可制备出较高含量Alb的PAC,制备条件对PAC中Alb的含量影响很大．B值的升高可以提高PAC中Alb的含量,但铝浓度的提高和熟化时间的延长则会降低产品中Alb的含量．反应温度为80℃左右时可制备出高Alb含量的PAC．加药时间和熟化时间对制备的影响不大．     

聚硅氯化铝（PASC）的形态分布及转化规律：Ⅰ.Al—Ferron逐时络合比色？…

采用Ａｌ－Ｆｅｒｒｏｎ逐时络合比色法比较研究了ＰＡＳＣ与ＰＡＣ中铝的形态分布及转化规律。实际结果表明,在ＰＡＳＣ中,由于聚硅酸与铝水解聚合产物的相互作用,使得铝的水解聚合形态分布及转化情况发生了变化。     

聚合铝基复合混凝剂残余铝及混凝性能的初步研究

以不同碱化度(B)的聚合氯化铝(PAC)和二甲基二烯丙基氯化铵均聚物(PDMDAAC)制备聚合氯化铝-二甲基二烯丙基氯化铵均聚物复合混凝剂(PAC-PDMDAAC)，试验了其处理模拟水的除浊效果及水体的残余铝量。结果表明：PAG-PDMDAAC较PAC具有更低的投加量，更好的除浊效果，处理后水体具有更低的残余铝量。B和PDMDAAC质量百分含量(P％)对PAC-PDMDAAC除浊效果及水体的残余铝量有不同程度的影响。     

多功能高铁絮凝剂电化学合成的机理和条件

本文研究了采用电解加复合稳定剂的方法制备ＦｅＯ４＾２－絮凝剂的电化学与溶液化学过程机制，分析了ＯＨ＾－膜平衡过程对ＦｅＯ４＾２－形成的影响，探讨了ＦｅＯ４＾２－水溶液分解的诱发因素，初步确定了ＦｅＯ４＾２－电化学合成的最佳条件。研究结果表明，适宜的电量参数，合理的电解液组成和高效的ＯＨ＾－膜渗透是顺利进行稳定化ＦｅＯ４＾２－电解合成的三个要素。     

Removal of phenol by powdered activated carbon adsorption

In this study, the adsorption performance of powdered activated carbon (PAC) on phenol was investigated in aqueous solutions. Batch adsorption studies were performed to evaluate the effects of various experimental parameters like PAC type, PAC dose, initial solution pH, temperature and pre-oxidation on the adsorption of phenol by PAC and establish the adsorption kinetics, thermodynamics and isothermal models. The results indicated that PAC adsorption is an effective method to remove phenol from water, and the effects of all the five factors on adsorption of phenol were significant. The adsorption rate of phenol by PAC was rapid, and more than 80% phenol could be absorbed by PAC within the initial 10 min. The adsorption process can be well described by pseudo-second-order adsorption kinetic model with rate constant amounted to 0.0313, 0.0305 and 0.0241 mg·μg ^-1·min ^-1 with coal, coconut shell and bamboo charcoal. The equilibrium data of phenol absorbed onto PAC were analyzed by Langmuir, Freundlich and Tempkin adsorption isotherms and Freundlich adsorption isotherm model gave the best correlation with the experimental data. Thermodynamic parameters such as the standard Gibbs free energy (?G^o), enthalpy (?H^o) and entropy (?S^o) obtained in this study indicated that the adsorption of phenol by PAC is spontaneous, exothermic and entropy decreasing.     

Cement-based solidification/stabilization of contaminated soils by nitrobenzene

The cement-based solidification/stabilization (S/S) of nitrobenzene (NB) contaminated soils, with cement and lime as binders, sodium silicate solution and powder activated carbon (PAC) as additives, was optimized through an orthogonal experiment, and S/S efficiency was estimated by both leaching test and volatilization measurement. The leaching test results showed that the factors affecting S/S efficiency were NB concentration, cement-to-lime ratio and binder-to-soils ratio, in sequence. With increasing curing time, the leaching concentration of NB between different levels of the same factor in the orthogonal experiment decreased, and less than 9% NB leached out from the 28 d cured samples. The volatilization measurement results indicated that 0.5‰ of NB was volatilized during the mixing and curing processes for the samples without PAC in the 28 d cycle, whereas adding 2 wt% and 5 wt% PAC, with respect to the weight of contaminated soils, could reduce NB volatilization to half of its original values either during the mixing or curing process. The optimizing formula, that is, contaminated soils (dry weight):cement:lime= 100:25:25, with 5 wt% additional sodium silicate and 2 wt% additional PAC, was applied to the engineering application of NB contaminated soils. Both the leaching test results of the product and the ambient air quality monitoring results met related regulations during the treating process.     

工业聚合氯化铝的形态分布及混凝效果

对铝浓度为2.50mol·l-1的聚合氯化铝.采用Al-Ferron络合比色法和烧杯混凝实验对样品的形态分布和混凝性能进行了研究.结果表明:三个工业系列样品中Al的形态分布规律基本一致,Ala随盐基度的升高而逐渐降低;Alc随盐基度的升高而升高;Alb则先随盐基度的升高而升高,达到最大值后,再随盐基度的升高而降低.同一系列样品在相同加药条件下,盐基度愈高,混凝效果愈好,Alb含量愈高,混凝效果并不一定愈好.因此,提高Alb不一定能提高混凝效果,工业产品的质量控制以及追求目标应当是尽量提高盐基度,而不是Alb的含量.     

Separating method and dynamic processes of Nano-Al13

In order to investigate the characteristics of pure Nano-Al₁₃, Nano-Al₁₃ was separated and purified from a series of poly-aluminum chloride (PAC) solutions which had the same Al₁₃ percentage but different total Al concentrations, by using column chromatography, ethanol-acetone resolving and SO^2? ₄/Ba²⁺ displacement. The Al₁₃ species yield was characterized by Al-ferron timed complexation spectrophotometry and ²⁷Al-NMR (nuclear magnetic resonance). The coagulation efficiency of Nano-Al₁₃, PAC and AlCl₃ in synthetic water was also investigated by Jar tests. The dynamic process and aggregation state of kaolin suspensions coagulating with Nano-Al₁₃, PAC and AlCl₃ were similarly investigated using a photometric dispersion analyzer 2000 (PDA2000). The experimental results indicated that the ethanol-acetone resolving method was simple and could separate the PAC solution at different concentrations, while column chromatography could separate PAC solutions at low concentrations. The SO₄ ^2?/Ba²⁺ displacement method could separate PAC solutions at high concentrations. However, extra inorganic cation and anion could be added in the solution during separation. The coagulation efficiency and dynamic experimental results showed that Nano-Al₁₃ with high positive-charged species was effective in removing turbidity and color. The dynamic process results showed that Nano-Al₁₃ also had the best recovery capability after shearing compared with PAC and AlCl₃ because the Nano-Al₁₃ conformation is more effective in charge neutralization.     

Polynuclear aromatic compounds in kerosene,diesel and unmodified sunflower oil and in respective engine exhaust particulate emissions

Polynuclear aromatic compounds (PAC) were characterized in diesel fuel, kerosene fuel and unmodified sunflower oil as well as in their respective engine exhaust particulates. Diesel fuel was found to contain high amounts of different PAC, up to a total concentration of 14,740?ppm, including carbazole and dibenzothiophene, which are known carcinogens. Kerosene fuel was also found to contain high amounts of different PAC, up to a total concentration of 10,930?ppm, consisting mainly of lower molecular weight (MW) naphthalene and its alkyl derivatives, but no PAC component peaks were detected in the unmodified sunflower oil. Engine exhaust particulates sampled from a modified one-cylinder diesel engine running on diesel, kerosene and unmodified sunflower oil, respectively, were found to contain significantly high concentrations of different PAC, including many of the carcinogenic ones, in the soluble organic fraction (SOF). PAC concentrations detected at the exhaust outlet indicated that most of the PAC that were present in diesel and kerosene fuels before the test runs got completely burnt out during combustion in the engine whereas some new ones were also formed. The difference between the character and composition of PAC present in the fuels and those emitted in the exhaust particulates indicated that exhaust PAC were predominantly combustion generated. High amounts of PAC, up to totals of 52,900 and 4830?µg?m^?3 of burnt fuel, in diesel and kerosene exhaust particulates, respectively, were detected in the dilution tunnel when the exhaust emissions were mixed with atmospheric air. Significant amounts of PAC were also emitted when the engine was run on unmodified sunflower oil with a total concentration of 17,070?µg?m^?3 of burnt fuel detected in the dilution tunnel. High proportions of the combustion-generated PAC determined when the engine was run on diesel, kerosene and unmodified sunflower, respectively, consisted of nitrogen-containing PAC (PANH) and sulphur-containing PAC (PASH).