Sorbents with high efficiency for CO2 capture based on amines-supported carbon for biogas upgrading

Sorbents for CO_2 capture have been prepared by wet impregnation of a commercial active carbon(Ketjen-black, Akzo Nobel) with two CO_2-philic compounds, polyethylenimine(PEI)and tetraethylenepentamine(TEPA), respectively. The effects of amine amount(from 10 to70 wt.%), CO_2 concentration in the feed, sorption temperature and gas hourly space velocity on the CO_2 capture performance have been investigated. The sorption capacity has been evaluated using the breakthrough method, with a fixed bed reactor equipped with on line gas chromatograph. The samples have been characterized by N_2 adsorption–desorption,scanning electron microscopy and energy dispersive X-ray(SEM/EDX). A promising CO_2 sorption capacity of 6.90 mmol/gsorbenthas been obtained with 70 wt.% of supported TEPA at 70℃ under a stream containing 80 vol% of CO_2. Sorption tests, carried out with simulated biogas compositions(CH_4/CO_2mixtures), have revealed an appreciable CO_2 separation selectivity; stable performance was maintained for 20 adsorption–desorption cycles.     

Optimization of CO2 adsorption capacity and cyclical adsorption/desorption on tetraethylenepentamine-supported surface-modified hydrotalcite

The objective of this research was to investigate CO_2adsorption capacity of tetraethylenepentamine-functionalized basic-modified calcined hydrotalcite(TEPA/b-c HT)sorbents at atmospheric pressure formed under varying TEPA loading levels,temperatures,sorbent weight to total gaseous flow rate(W/F)ratios and CO_2concentrations in the influent gas.The TEPA/b-c HT sorbents were characterized by means of X-ray diffraction(XRD),Fourier transform infrared spectrometry(FT–IR),thermal gravimetric analysis(TGA),Brunauer–Emmet–Teller(BET)analysis of nitrogen(N_2)adsorption/desorption and carbon–hydrogen–nitrogen(CHN)elemental analysis.Moreover,a full 2~4factorial design with three central points at a 95%confidence interval was used to screen important factor(s)on the CO_2adsorption capacity.It revealed that85.0%variation in the capacity came from the influence of four main factors and the15.0%one was from their interactions.A face-centered central composite design response surface method(FCCCD–RSM)was then employed to optimize the condition,the maximal capacity of 5.5–6.1 mmol/g was achieved when operating with a TEPA loading level of 39%–49%(W/W),temperature of 76–90°C,W/F ratio of 1.7–2.60(g·sec)/cm~3and CO_2concentration of 27%–41%(V/V).The model fitted sufficiently the experimental data with an error range of±1.5%.From cyclical adsorption/desorption and selectivity at the optimal condition,the 40%TEPA/b-c HT still expressed its effective performance after eight cycles.     

Enhanced catalytic complete oxidation of 1,2-dichloroethane over mesoporous transition metal-doped γ-Al2O3

High-surface-area mesoprous powders of γ-Al₂O₃ doped with Cu^2 +, Cr^3 +, and V^3 + ions were prepared via a modified sol–gel method and were investigated as catalysts for the oxidation of chlorinated organic compounds. The composites retained high surface areas and pore volumes comparable with those of undoped γ-Al₂O₃ and the presence of the transition metal ions enhanced their surface acidic properties. The catalytic activity of the prepared catalysts in the oxidation of 1,2-dichloroethane (DCE) was studied in the temperature range of 250–400°C. The catalytic activity and product selectivity were strongly dependent on the presence and the type of dopant ion. While Cu^2 +- and Cr^3 +-containing catalysts showed 100% conversion at 300°C and 350°C, V^3 +-containing catalyst showed considerably lower conversion. Furthermore, while the major products of the reactions over γ-alumina were vinyl chloride (C₂H₃Cl) and hydrogen chloride (HCl) at all temperatures, Cu- and Cr-doped catalysts showed significantly stronger capability for deep oxidation to CO₂.     

以粉煤灰为原料制备低温CO2吸附剂的工艺参数优化

利用高铝粉煤灰预脱硅液作为载体原料,通过使用胺基化合物对载体改性制备低温CO_2吸附剂.应用6 sigma中的工具,对制备工艺进行优化,得到理想的吸附剂,并对吸附剂样品进行表征.结果表明制备的CO_2吸附剂表现出良好的CO_2吸附性能.此类CO_2吸附剂具有吸附容量高(160 mg·g~(-1))、吸附速率快、对设备腐蚀低、成本低廉等特点,是一种极具工业应用潜力的CO_2吸附剂.     

Carbon dioxide capture using polyethylenimine-loaded mesoporous carbons

A high efficiency sorbent for CO2 capture was developed by loading polyethylenimine (PEI) on mesoporous carbons which possessed well-developed mesoporous structures and large pore volume. The physicochemical properties of the sorbent were characterized by N2 adsorption/desorption, scanning electron microscopy (SEM), thermal gravimetric analysis (TG) and Fourier transform infrared spectroscopy (FT-IR) techniques followed by testing for CO2 capture. Factors that affected the sorption capacity of the sorbent were studied. The sorbent exhibited extraordinary capture capacity with CO2 concentration ranging from 5% to 80%. The optimal PEI loading was determined to be 65 wt.% with a CO2 sorption capacity of 4.82 mmol-CO2 /g-sorbent in 15% CO2 /N2 at 75°C, owing to low mass-transfer resistance and a high utilization ratio of the amine compound (63%). Moisture had a promoting effect on the sorption separation of CO2 . In addition, the developed sorbent could be regenerated easily at 100°C, and it exhibited excellent regenerability and stability. These results indicate that this PEI-loaded mesoporous carbon sorbent should have a good potential for CO2 capture in the future.     

MgO-based adsorbents for CO2 adsorption: Influence of structural and textural properties on the CO2 adsorption performance

A series of MgO-based adsorbents were prepared through solution–combustion synthesis and ball-milling process.The prepared MgO-based powders were characterized using X-ray diffraction,scanning electron microscopy,N_2 physisorption measurements,and employed as potential adsorbents for CO_2 adsorption.The influence of structural and textural properties of these adsorbents over the CO_2 adsorption behaviour was also investigated.The results showed that MgO-based products prepared by solution–combustion and ball-milling processes,were highly porous,fluffy,nanocrystalline structures in nature,which are unique physico-chemical properties that significantly contribute to enhance their CO_2 adsorption.It was found that the MgO synthesized by solution combustion process,using a molar ratio of urea to magnesium nitrate(2:1),and treated by ball-milling during 2.5 hr(MgO-BM2.5h),exhibited the maximum CO_2 adsorption capacity of 1.611 mmol/g at 25℃ and 1 atm,mainly via chemisorption.The CO_2 adsorption behaviour on the MgO-based adsorbents was correlated to their improved specific surface area,total pore volume,pore size distribution and crystallinity.The reusability of synthesized MgO-BM2.5h was confirmed by five consecutive CO_2adsorption–desorption times,without any significant loss of performance,that supports the potential of MgO-based adsorbent.The results confirmed that the special features of MgO prepared by solution–combustion and treated by ball-milling during 2.5 hr are favorable to be used as effective MgO-based adsorbent in post-combustion CO_2 capture technologies.     

Effect of drainage on CO2, CH4, and N2O fluxes from aquaculture ponds during winter in a subtropical estuary of China

Aquaculture ponds are dominant features of the landscape in the coastal zone of China.Generally,aquaculture ponds are drained during the non-culture period in winter.However,the effects of such drainage on the production and flux of greenhouse gases(GHGs)from aquaculture ponds are largely unknown.In the present study,field-based research was performed to compare the GHG fluxes between one drained pond(DP,with a water depth of 0.05 m)and one undrained pond(UDP,with a water depth of 1.16 m)during one winter in the Min River estuary of southeast China.Over the entire study period,the mean CO_2flux in the DP was(0.75±0.12)mmol/(m~2·hr),which was significantly higher than that in the UDP of(-0.49±0.09)mmol/(m~2·hr)(p0.01).This indicates that drainage drastically transforms aquaculture ponds from a net sink to a net source of CO_2in winter.Mean CH_4and N_2O emissions were significantly higher in the DP compared to those in the UDP(CH_4=(0.66±0.31)vs.(0.07±0.06)mmol/(m~2·hr)and N_2O=(19.54±2.08)vs.(0.01±0.04)μmol/(m~2·hr))(p0.01),suggesting that drainage would also significantly enhance CH_4and N_2O emissions.Changes in environmental variables(including sediment temperature,p H,salinity,redox status,and water depth)contributed significantly to the enhanced GHG emissions following pond drainage.Furthermore,analysis of the sustained-flux global warming and cooling potentials indicated that the combined global warming potentials of the GHG fluxes were significantly higher in the DP than in the UDP(p0.01),with values of739.18 and 26.46 mg CO_2-eq/(m~2·hr),respectively.Our findings suggested that drainage of aquaculture ponds can increase the emissions of potent GHGs from the coastal zone of China to the atmosphere during winter,further aggravating the problem of global warming.     

Breakthrough CO2 adsorption in bio-based activated carbons

In this work, the effects of different methods of activation on CO₂ adsorption performance of activated carbon were studied. Activated carbons were prepared from biochar, obtained from fast pyrolysis of white wood, using three different activation methods of steam activation, CO₂ activation and Potassium hydroxide (KOH) activation. CO₂ adsorption behavior of the produced activated carbons was studied in a fixed-bed reactor set-up at atmospheric pressure, temperature range of 25–65°C and inlet CO₂ concentration range of 10–30 mol% in He to determine the effects of the surface area, porosity and surface chemistry on adsorption capacity of the samples. Characterization of the micropore and mesopore texture was carried out using N₂ and CO₂ adsorption at 77 and 273 K, respectively. Central composite design was used to evaluate the combined effects of temperature and concentration of CO₂ on the adsorption behavior of the adsorbents. The KOH activated carbon with a total micropore volume of 0.62 cm³/g and surface area of 1400 m²/g had the highest CO₂ adsorption capacity of 1.8 mol/kg due to its microporous structure and high surface area under the optimized experimental conditions of 30 mol% CO₂ and 25°C. The performance of the adsorbents in multi-cyclic adsorption process was also assessed and the adsorption capacity of KOH and CO₂ activated carbons remained remarkably stable after 50 cycles with low temperature (160°C) regeneration.     

Responses of greenhouse gas fluxes to experimental warming in wheat season under conventional tillage and no-tillage fields

Understanding the effects of warming on greenhouse gas(GHG, such as N_2O, CH_4 and CO_2 )feedbacks to climate change represents the major environmental issue. However, little information is available on how warming effects on GHG fluxes in farmland of North China Plain(NCP). An infrared warming simulation experiment was used to assess the responses of N_2O, CH_4 and CO_2 to warming in wheat season of 2012–2014 from conventional tillage(CT) and no-tillage(NT) systems. The results showed that warming increased cumulative N_2O emission by 7.7% in CT but decreased it by 9.7% in NT fields(p 0.05). Cumulative CH_4 uptake and CO_2 emission were increased by 28.7%–51.7% and 6.3%–15.9% in both two tillage systems,respectively(p 0.05). The stepwise regressions relationship between GHG fluxes and soil temperature and soil moisture indicated that the supply soil moisture due to irrigation and precipitation would enhance the positive warming effects on GHG fluxes in two wheat seasons.However, in 2013, the long-term drought stress due to infrared warming and less precipitation decreased N_2O and CO_2 emission in warmed treatments. In contrast, warming during this time increased CH_4 emission from deep soil depth. Across two years wheat seasons, warming significantly decreased by 30.3% and 63.9% sustained-flux global warming potential(SGWP) of N_2O and CH_4 expressed as CO_2 equivalent in CT and NT fields, respectively. However, increase in soil CO_2 emission indicated that future warming projection might provide positive feedback between soil C release and global warming in NCP.     

The roles of active species in photo-decomposition of organic compounds by microwave powered electrodeless discharge lamps

Knowledge of the effective radiation spectrum irradiating substrates from microwave powered electrodeless discharge lamps(MEDLs), and the active species that directly oxidize substrates in the photolytic process, is fragmentary and unclear. In this work, we conducted a comparative study using MEDLs made with quartz envelopes(MEDL-quartz) and with borosilicate Pyrex envelopes(MEDL-Pyrex) targeting the degradation of Rhodamine B(Rh B)via radical-extinguishing tests. We found that UVC/UVB radiation is essential to generate·OH and H2O2 in the MEDL-quartz system. The degradation of Rh B mostly originates from·OH species, which account for a contribution of 53.8%, while the remaining contribution is attributed to oxidation by H2O2 and direct photolysis. This degradation is influenced by several parameters. Acidic and neutral p Hs, but not extreme alkaline p H, benefit the degradation. To ensure a high intensity of UVC/UVB, the optimum ratio of the MEDL volume to the aqueous solution volume(VL/VS) is 0.4. Concentrations of 0.15–0.20 mmol/L of Rh B are suitable to obtain an effective quantum absorbance in the MEDL-quartz system,showing a high decomposition rate of 5.6 × 10-3(mmol/L)min-1. Moreover, two other substrates, Reactive Brilliant Red X-3B and Safranine T, were tested and found to be efficiently degraded in the MEDL-quartz system.     

Development of a hybrid photo-bioreactor and nanoparticle adsorbent system for the removal of CO2 , and selected organic and metal co-pollutants

Fossil fuel combustion and many industrial processes generate gaseous emissions that contain a number of toxic organic pollutants and carbon dioxide (CO₂) which contribute to climate change and atmospheric pollution. There is a need for green and sustainable solutions to remove air pollutants, as opposed to conventional techniques which can be expensive, consume additional energy and generate further waste. We developed a novel integrated bioreactor combined with recyclable iron oxide nano/micro-particle adsorption interfaces, to remove CO_2, and undesired organic air pollutants using natural particles, while generating oxygen. This semi-continuous bench-scale photo-bioreactor was shown to successfully clean up simulated emission streams of up to 45% CO₂ with a conversion rate of approximately 4% CO₂ per hour, generating a steady supply of oxygen (6 mmol/hr), while nanoparticles effectively remove several undesired organic by-products. We also showed algal waste of the bioreactor can be used for mercury remediation. We estimated the potential CO₂ emissions that could be captured from our new method for three industrial cases in which, coal, oil and natural gas were used. With a 30% carbon capture system, the reduction of CO₂ was estimated to decrease by about 420,000, 320,000 and 240,000 metric tonnes, respectively for a typical 500 MW power plant. The cost analysis we conducted showed potential to scale-up, and the entire system is recyclable and sustainable. We further discuss the implications of usage of this complete system, or as individual units, that could provide a hybrid option to existing industrial setups.     

Toward rational design of amines for CO2 capture: Substituent effect on kinetic process for the reaction of monoethanolamine with CO2

Amines have been considered as promising candidates for post-combustion CO₂ capture. A mechanistic understanding for the chemical processes involved in the capture and release of CO₂ is important for the rational design of amines. In this study, the structural effects of amines on the kinetic competition among three typical products (carbamates, carbamic acids and bicarbonate) from amines + CO₂ were investigated, in contrast to previous thermodynamic studies to tune the reaction of amines with CO₂ based on desirable reaction enthalpy and reaction stoichiometry. We used a quantum chemical method to calculate the activation energies (E_a) for the reactions of a range of substituted monoethanolamines with CO₂ covering three pathways to the three products. The results indicate that the formation of carbamates is the most favorable, among the three considered products. In addition, we found that the E_a values for all pathways linearly correlate with pK_a of amines, and more importantly, the kinetic competition between carbamate and bicarbonate absorption pathways varies with pK_a of the amines, i.e. stronger basicity results in less difference in E_a. These results highlight the importance of the consideration of kinetic competition among different reaction pathways in amine design.     

Ozone concentrations, flux and potential effect on yield during wheat growth in the Northwest-Shandong Plain of China

Ozone (O₃) concentration and flux (F_o) were measured using the eddy covariance technique over a wheat field in the Northwest-Shandong Plain of China. The O₃-induced wheat yield loss was estimated by utilizing O₃ exposure-response models. The results showed that: (1) During the growing season (7 March to 7 June, 2012), the minimum (16.1 ppbV) and maximum (53.3 ppbV) mean O₃ concentrations occurred at approximately 6:30 and 16:00, respectively. The mean and maximum of all measured O₃ concentrations were 31.3 and 128.4 ppbV, respectively. The variation of O₃ concentration was mainly affected by solar radiation and temperature. (2) The mean diurnal variation of deposition velocity (V_d) can be divided into four phases, and the maximum occurred at noon (12:00). Averaged V_d during daytime (6:00–18:00) and nighttime (18:00–6:00) were 0.42 and 0.14 cm/sec, respectively. The maximum of measured V_d was about 1.5 cm/sec. The magnitude of V_d was influenced by the wheat growing stage, and its variation was significantly correlated with both global radiation and friction velocity. (3) The maximum mean F_o appeared at 14:00, and the maximum measured F_o was − 33.5 nmol/(m²·sec). Averaged F_o during daytime and nighttime were − 6.9 and − 1.5 nmol/(m²·sec), respectively. (4) Using O₃ exposure-response functions obtained from the USA, Europe, and China, the O₃-induced wheat yield reduction in the district was estimated as 12.9% on average (5.5%–23.3%). Large uncertainties were related to the statistical methods and environmental conditions involved in deriving the exposure-response functions.     

Response surface method for modeling the removal of carbon dioxide from a simulated gas using water absorption enhanced with a liquid-film-forming device

This paper presents the results from using a physical absorption process to absorb gaseous CO_2mixed with N_2using water by producing tiny bubbles via a liquid-film-forming device(LFFD)that improves the solubility of CO_2in water.The influence of various parameters—pressure,initial CO_2concentration,gas-to-liquid ratios,and temperature—on the CO_2removal efficiency and its absorption rate in water were investigated and estimated thoroughly by statistical polynomial models obtained by the utilization of the response surface method(RSM)with a central composite design(CCD).Based on the analysis,a high efficiency of CO_2capture can be reached in conditions such as low pressure,high CO_2concentration at the inlet,low gas/liquid ratio,and low temperature.For instance,the highest removal efficiency in the RSM–CCD experimental matrix of nearly 80%occurred for run number 20,which was conducted at 0.30 MPa,CO_2concentration of 35%,gas/liquid ratio of 0.71,and temperature of 15°C.Furthermore,the coefficients of determination,R~2,were 0.996 for the removal rate and 0.982 for the absorption rate,implying that the predicted values computed by the constructed models correlate strongly and fit well with the experimental values.The results obtained provide essential information for implementing this method properly and effectively and contribute a promising approach to the problem of CO_2capture in air pollution treatment.     

Carbon balance of an intensively grazed temperate pasture in two climatically contrasting years

Grazed grasslands occupy 26% of the earth's ice free land surface and are therefore an important component of the global C balance. In New Zealand, pastoral agriculture is the dominant land use and recent research has shown that soils under intensive dairy pastures have lost large amounts of carbon (∼1000 kg C ha⁻¹ y⁻¹) during the past few decades. The objective of this research was to determine the net ecosystem carbon balance (NECB) of an intensively grazed dairy pasture in New Zealand. Net ecosystem CO₂ exchange (NEE) was measured using an eddy covariance (EC) system from 1 January 2008 to 31 December 2009. Other C imports (feed) and exports (milk, methane, leaching, and harvested biomass) were calculated from farm production data and literature values. During 2008 there was a one in 100 year drought during summer/autumn, which was followed by a very wet winter. There were no prolonged periods of above or below average rainfall or soil moisture in 2009, but temperatures were consistently lower than 2008. The severe summer/autumn drought during 2008 caused a loss of CO₂ to the atmosphere, but annual NEE remained negative (a CO₂ sink, −1610 ± 500 kg C ha⁻¹), because CO₂ lost during the drought was regained during the winter and spring. The site was also a net CO₂ sink during 2009 despite the colder than usual conditions (−2290 ± 500 kg C ha⁻¹). Including C imports and exports in addition to CO₂ exchange revealed that the site was a C sink in both years, with a NECB of 590 ± 560 kg C ha⁻¹ in 2008, and 900 ± 560 kg C ha⁻¹ in 2009. The C sequestration found in this study is in agreement with most other Northern Hemisphere EC studies of grazed pastures on mineral soils, but is not consistent with the large C losses reported for soils under dairy pastures throughout New Zealand. In the current study (like many other EC studies) the influence of climatic conditions and management practices on the annual C balance was only semi-quantitatively assessed. An extended period of EC measurements combined with modelling is required to more accurately quantify the effect of different climatic conditions on the annual C balance, and the influence of different management practices needs to be quantified using specifically designed studies (such as paired EC towers), so that practices which minimise C losses and maximise C sequestration can be identified.     

Effects of elevated atmospheric CO2 concentration and temperature on the soil profile methane distribution and diffusion in rice–wheat rotation system

The aim of this experiment was to determine the impacts of climate change on soil profile concentrations and diffusion effluxes of methane in a rice–wheat annual rotation ecosystem in Southeastern China. We initiated a field experiment with four treatments: ambient conditions (CKs), CO₂ concentration elevated to ~ 500 μmol/mol (FACE), temperature elevated by ca. 2°C (T) and combined elevation of CO₂ concentration and temperature (FACE + T). A multilevel sampling probe was designed to collect the soil gas at four different depths, namely, 7 cm, 15 cm, 30 cm and 50 cm. Methane concentrations were higher during the rice season and decreased with depth, while lower during the wheat season and increased with depth. Compared to CK, mean methane concentration was increased by 42%, 57% and 71% under the FACE, FACE + T and T treatments, respectively, at the 7 cm depth during the rice season (p < 0.05). Mean methane diffusion effluxes to the 7 cm depth were positive in the rice season and negative in the wheat season, resulting in the paddy field being a source and weak sink, respectively. Moreover, mean methane diffusion effluxes in the rice season were 0.94, 1.19 and 1.42 mg C/(m²·hr) in the FACE, FACE + T and T treatments, respectively, being clearly higher than that in the CK. The results indicated that elevated atmospheric CO₂ concentration and temperature could significantly increase soil profile methane concentrations and their effluxes from a rice–wheat field annual rotation ecosystem (p < 0.05).     

Response of gaseous carbon emissions to low-level salinity increase in tidal marsh ecosystem of the Min River estuary, southeastern China

Although estuarine tidal marshes are important contributors to the emission of greenhouse gases into the atmosphere, the relationship between carbon dioxide(CO_2), methane(CH_4)emission, and environmental factors, with respect to estuarine marshes, has not been clarified thoroughly. This study investigated the crucial factors controlling the emission of CO_2 and CH_4from a freshwater marsh and a brackish marsh located in a subtropical estuary in southeastern China, as well as their magnitude. The duration of the study period was November 2013 to October 2014. Relevant to both the field and incubation experiments, the CO_2 and CH_4emissions from the two marshes showed pronounced seasonal variations. The CO_2 and CH_4emissions from both marshes demonstrated significant positive correlations with the air/soil temperature(p 0.01), but negative correlations with the soil electrical conductivity and the pore water/tide water Cl-and SO_4~(2-)(p 0.01). The results indicate no significant difference in the CO_2 emissions between the freshwater and brackish marshes in the subtropical estuary, whereas there was a difference in the CH_4 emissions between the two sites(p 0.01). Although future sea-level rise and saltwater intrusion could reduce the CH_4 emissions from the estuarine freshwater marshes, these factors had little effect on the CO_2 emissions with respect to an increase in salinity of less than 5‰. The findings of this study could have important implications for estimating the global warming contributions of estuarine marshes along differing salinity gradients.     

Mesoporous carbon adsorbents from melamine-formaldehyde resin using nanocasting technique for CO2 adsorption

Mesoporous carbon adsorbents, having high nitrogen content, were synthesized via nanocasting technique with melamine–formaldehyde resin as precursor and mesoporous silica as template. A series of adsorbents were prepared by varying the carbonization temperature from 400 to 700°C. Adsorbents were characterized thoroughly by nitrogen sorption, X-ray diffraction(XRD), scanning electron microscopy(SEM), transmission electron microscopy(TEM), thermogravimetric analysis(TGA), elemental(CHN) analysis, Fourier transform infrared(FTIR) spectroscopy and Boehm titration. Carbonization temperature controlled the properties of the synthesized adsorbents ranging from surface area to their nitrogen content, which play major role in their application as adsorbents for CO_2 capture.The nanostructure of these materials was confirmed by XRD and TEM. Their nitrogen content decreased with an increase in carbonization temperature while other properties like surface area, pore volume, thermal stability and surface basicity increased with the carbonization temperature. These materials were evaluated for CO_2 adsorption by fixed-bed column adsorption experiments. Adsorbent synthesized at 700°C was found to have the highest surface area and surface basicity along with maximum CO_2 adsorption capacity among the synthesized adsorbents. Breakthrough time and CO_2 equilibrium adsorption capacity were investigated from the breakthrough curves and were found to decrease with increase in adsorption temperature. Adsorption process for carbon adsorbent–CO_2 system was found to be reversible with stable adsorption capacity over four consecutive adsorption–desorption cycles. From three isotherm models used to analyze the equilibrium data, Temkin isotherm model presented a nearly perfect fit implying the heterogeneous adsorbent surface.     

Elevated atmospheric CO2 and drought effects on leaf gas exchange properties of barley

Atmospheric CO₂ concentration (C_a) is rising, predicted to cause global warming, and alter precipitation patterns. During 1994, spring barley (Hordeum vulgare L. cv. Alexis) was grown in a strip-split-plot experimental design to determine the effects that the main plot C_a treatments [A: Ambient at 370 μmol (CO₂) mol⁻¹; E: Enriched with free-air CO₂ enrichment (FACE) at ∼550 μmol (CO₂) mol⁻¹] had on several gas exchange properties of fully expanded sunlit primary leaves. The interacting strip-split-plot irrigation treatments were Dry or Wet [50% (D) or 100% (W) replacement of potential evapotranspiration] at ample nitrogen (261 kg N ha⁻¹) and phosphorous (29 kg P ha⁻¹) fertility. Elevated C_a facilitated drought avoidance by reducing stomatal conductance (g_s) by 34% that conserved water and enabled stomata to remain open for a longer period into a drought. This resulted in a 28% reduction in drought-induced midafternoon depression in net assimilation rate (A). Elevated C_a increased A by 37% under Dry and 23% under Wet. Any reduction in A under Wet conditions occurred because of nonstomatal limitations, whereas under Dry it occurred because of stomatal limitations. Elevated C_a increased the diurnal integral of A (A′) that resulted in an increase in the seasonal-long integral of A′ (A″) for barley leaves by 12% (P = 0.14) under both Dry and Wet - 650, 730, 905 and 1020 ± 65 g (C) m⁻² y⁻¹ for AD, ED, AW and EW treatments, respectively. Elevated C_a increased season-long average dry weight (DW_S; crown, shoots) by 14% (P = 0.02), whereas deficit irrigation reduced DW_S by 7% (P = 0.06), although these values may have been affected by a short but severe pea aphid [Acyrthosiphon pisum (Harris)] infestation. Hence, an elevated-C_a-based improvement in gas exchange properties enhanced growth of a barley crop.     

Estimating emissions from crop residue open burning in China based on statistics and MODIS fire products

With the objective of reducing the large uncertainties in the estimations of emissions from crop residue open burning, an improved method for establishing emission inventories of crop residue open burning at a high spatial resolution of 0.25°× 0.25° and a temporal resolution of1 month was established based on the moderate resolution imaging spectroradiometer(MODIS) Thermal Anomalies/Fire Daily Level3 Global Product(MOD/MYD14A1). Agriculture mechanization ratios and regional crop-specific grain-to-straw ratios were introduced to improve the accuracy of related activity data. Locally observed emission factors were used to calculate the primary pollutant emissions. MODIS satellite data were modified by combining them with county-level agricultural statistical data, which reduced the influence of missing fire counts caused by their small size and cloud cover. The annual emissions of CO_2, CO, CH_4,nonmethane volatile organic compounds(NMVOCs), N_2O, NO_x, NH_3, SO_2, fine particles(PM2.5),organic carbon(OC), and black carbon(BC) were 150.40, 6.70, 0.51, 0.88, 0.01, 0.13, 0.07, 0.43,1.09, 0.34, and 0.06 Tg, respectively, in 2012. Crop residue open burning emissions displayed typical seasonal and spatial variation. The highest emission regions were the Yellow-Huai River and Yangtse-Huai River areas, and the monthly emissions were highest in June(37%).Uncertainties in the emission estimates, measured as 95% confidence intervals, range from a low of within ±126% for N_2O to a high of within ± 169% for NH_3.