Removal of heavy metals from anaerobically digested sewage sludge by isolated indigenous iron-oxidizing bacteria

The removal of heavy metals (Cr, Cu, Zn, Ni and Pb) from anaerobically digested sludge from the Yuen Long wastewater treatment plant, Hong Kong, has been studied in a batch system using isolated indigenous iron-oxidizing bacteria. The inoculation of indigenous iron-oxidizing bacteria and the addition of FeSO4 accelerated the solubilization of Cr, Cu, Zn, Ni and Pb from the sludge. pH of the sludge decreased with an increase in Fe2+ concentrations and reached a low pH of 2-2.5 for treatments receiving both bacterial inoculation and FeSO4. After 16 days of bioleaching, the following heavy metal removal efficiencies were obtained: Cr 55.3%, Cu 91.5%, Zn 83.3%, Ni 54.4%, and Pb 16.2%. In contrast, only 2.6% of Cr, 42.9% of Cu, 72.1% of Zn, 22.8% of Ni and 0.56% of Pb were extracted from the control without the bacterial inoculation and addition of FeSO4. The residual heavy metal content in the leached sludge was acceptable for unrestricted use for agriculture. The experimental results confirmed the effectiveness of using the isolated iron-oxidizing bacteria for the removal of heavy metals from sewage sludge.     

调理剂对堆肥产品重金属生物有效性的影响

城市污泥中重金属含量及其生物有效性是限制污泥农用的主要因素,因此,研究污泥堆肥化处理过程中重金属生物有效性,对污泥的农用具有重要意义。实验以城市污泥为原料,以菌菇渣和秸秆为调理剂,设置4个处理:A(污泥∶菌菇渣∶秸秆=1∶0.4∶0.025)、B(污泥∶菌菇渣∶秸秆=1∶0.3∶0.025)、C(污泥∶秸秆=1∶0.12)和D(污泥∶秸秆=1∶0.09),进行好氧堆肥实验,采用BCR顺序提取法测定各种形态的重金属,研究堆肥前后重金属形态的变化规律。结果表明,城市污泥中Cu、Ni、Pb和Cr主要以可氧化态及残渣态存在,生物有效性较低,而Zn和Cd主要以酸溶态和可还原态存在,生物有效性较高;堆肥过程显著降低了Cu、Zn、Ni和Pb的生物有效性,并改变了Cu、Zn、Ni、Pb、Cr和Cd的形态分布,使污泥中的Cu、Zn、Ni、Pb和Cd向着更稳定的可氧化态或残渣态转变;污泥经过堆肥处理后,Cu、Zn和Ni 3种重金属生物有效性关系为:ABCD,与其他处理相比,处理A残渣态的Pb和Cr增加比例较多,综合来看,处理A对重金属生物有效性的降低最为明显,重金属钝化效果最佳。     

洛阳城市污水处理厂污泥中重金属形态及潜在生态风险评价

分析了洛阳市3个污水处理厂脱水污泥中Cu、Zn、Ni、Cr和Pb的含量,采用BCR法研究了污泥中重金属的形态分布特征,并利用地累积指数法（Igeo）和潜在生态危害指数法（RI）评价污泥在农用过程中重金属的潜在生态风险。结果表明,涧西污泥中Cu、Zn和Ni含量超过了农用泥质A级标准的限值（CJ/T309-2009）,而新区污泥和瀍东污泥显示出良好的农用性质。污泥中Cu和Cr主要以可氧化态存在,Zn主要以酸溶态和可还原态存在,迁移性强,Ni含量分布相对比较均匀,Pb主要以残渣态存在。Igeo表明,污泥中Cu、Zn是潜在的污染元素。RI表明,Cu表现出高潜在生态风险;Zn的总含量虽高,但Zn的生物毒性响应因子低,对污泥的潜在风险贡献较低。     

焦化废水处理过程外排污泥中重金属形态特征及其潜在环境风险

焦化废水处理过程所排放污泥中重金属的含量及化学形态是否构成环境风险将直接影响污泥处置方法的选择,为此,实验采用BCR顺序提取法分析了焦化废水处理站外排污泥中重金属(Cd、Hg、Pb、Cr、As、Ni、Zn、Cu和Mn)的形态特征,并采用地累积指数(Igeo)和潜在生态危害指数(RI)评价了重金属对土壤的潜在环境风险。研究结果表明:除Ni主要以可氧化态存在外,焦化废水外排污泥中其他几种重金属元素主要存在于残渣态,重金属元素的含量低于《城镇污水处理厂污染物排放标准(GB18918—2002)》中的控制限值;与城市污泥相比,焦化废水外排污泥具有低Pb、Cr、Zn、Cu含量,而高Cd、Hg、Mn含量的特点;基于Igeo和RI的评价结果,Cd和Hg是外排污泥中具有一定环境风险的元素,需要考虑其下游去向。焦化废水处理外排污泥中主要存在残渣态重金属成分,不表现为很高的环境风险,其处置应重点考虑其中有机污染物特别是POPs。     

Heavy metal accumulation in wheat plant grown in soil amended with industrial sludge

The concentrations of different forms of Zn, Cu, Mn, Ni, Cd, Cr, Pb and Fe metals were determined for the roadside sludge collected from pickling-rolling and electroplating industrial area. In sludge the relative abundance of total heavy metals were Fe>Mn>Cr>Ni>Cu>Pb>Zn>Cd and DTPA-extractable metals were in the order--Fe>Ni>Mn>Cr>Cu>Zn>Pb>Cd. Pot-culture experiment was conducted in soils amended with sludge (0%, 10%, 20%, 30%), pretreated with lime (0%, 0.5% and 1%). The soils were alkaline in nature (pH>8.3) with organic carbon contents were 0.34% and 0.72%. The most abundant total and bio-available metal was Fe. Two wheat seedlings were grown in each pot containing 3kg sludge-amended or control soil and the experiment was conducted till harvesting. Application of sludge increased both total and bio-available forms of metals in the soils, while lime application decreased the bioavailability of heavy metals in sludge-amended soils. The content of organic carbon showed positive correlation with all metals except Zn, Cr and Pb. CEC also showed a strong positive correlation (R2>0.7) with Fe, Mn, Cu, Ni and Cd. Though wheat plants are not accumulators, the translocation efficiency was appreciably high. The translocation factor from shoot to grain was found smaller than that of root to shoot of wheat plants. This makes an implication that the heavy metal accumulation was proportionally lesser in grain than in shoot. In, 10% sludge with 0.5% lime-amended soils; each of these toxic heavy metals was found to be within permissible range (USEPA). Hence, on the basis of present study, the best possible treatment may be recommended.     

Metal contamination and solid phase partitioning of metals in urban roadside sediments

This study was undertaken to assess the anthropogenic impact on metal concentrations of urban roadside sediments (N = 633) in Seoul city, Korea and to estimate the potential mobility of selected metals (Zn, Cu, Pb, Cr, Ni, and Cd) using sequential extraction. Comparison of metal concentrations in roadside sediments with mean background values in sediments collected from first- or second-order streams in Korea shows that Zn, Cu and Pb are most affected by anthropogenic inputs. The 206Pb/207Pb ratios of roadside sediments (range = 1.1419-1.1681; mean 1.1576 +/- 0.0068) suggest that Pb is mainly derived from industrial sources rather than from leaded gasoline. A five-step sequential extraction of roadside sediments showed that Zn, Cd and to a lesser degree Ni occur predominantly in the carbonate bound fraction, while Pb is highest in the reducible fraction, Cu in the organic fraction, and Cr in the residual fraction. It was found that the concentrations in the readily available exchangeable fraction were generally low for most metals examined, except for Ni whose exchangeable fraction was appreciable (average 15.2%). Considering the proportion of metals bound to the exchangeable and carbonate fractions, the comparative mobility of metals probably decreases in the order of Zn > Ni > Cd > Pb > Cu > Cr. As potential changes of redox state and pH may remobilize the metals bound to carbonates, reducible, and/or organic matter, and may release and flush them through drain networks into streams, careful monitoring of environmental conditions appears to be very important. With respect to ecotoxicity, it is apparent the Zn and Cu pollution is of particular concern in Seoul city.     

Heavy metals in untreated/treated urban effluent and sludge from a biological wastewater treatment plant

Background, Aim and Scope

The presence of heavy metals in wastewater is one of the main causes of water and soil pollution. The aim of the present study was to investigate the removal of Cd, Cu, Pb, Hg, Mn, Cr and Zn in urban effluent by a biological wastewater treatment, as well as to quantify the levels of As, Be, Cd, Cr, Cu, Fe, Hg, Mn, Ni, Pb, Sn, Tl, V and Zn in dewatering sludge from the Biological Wastewater Treatment Plant to Ribeirão Preto (RP-BWTP), Brazil.

Materials and Methods

Concentrations of Cd, Cr, Cu, Mn and Pb in wastewater and those of Ni in sludge were determined by atomic absorption spectrophotometry with graphite furnace atomization. Mercury concentrations in wastewater were measured by hydride generation atomic spectrophotometry, and Zn levels were determined by atomic absorption spectrophotometry using acetylene flame. In sludge, the levels of As, Be, Cd, Cr, Cu, Fe, Hg, Mn, Pb, Sn, Tl, V and Zn were determined by inductively coupled plasma-mass spectrometry.

Results

The percentages of removal efficiency (RE) were the following: Hg 61.5%, Cd 60.0%, Zn 44.9%, Cu 44.2%, PB 39.7%, Cr 16,5% and Mn 10.4%. In turn, the mean concentrations (mg/kg) of metals in dewatering sludge followed this increasing order: Tl (<0.03), Hg (0.31), Be (0.43), As (1.14), Cd (1.34), V (59.2), Pb (132.1), Sn (166.1), Cr (195.0), Mn (208.1), Ni (239.4), Cu (391.7), Zn (864.4) and Fe (20537).

Discussion

The relationship between metal levels in untreated wastewater, as well as the removal efficiency are in agreement with previous data from various investigators, It is important to note that metal removal efficiency is not only affected by metal ion species and concentration, but also by other conditions such as operating parameters, physical, chemical, and biological factors.

Conclusions

Metal values recorded for treated wastewater and sludge were within the maximum permitted levels established by the Environmental Sanitation Company (CETESB), São Paulo, Brazil.

Recommendations

There is an urgent need for the authorities who are responsible for legislation on sludge uses in agriculture of establishing safety levels for As, Be, Hg, Sn, Tl and V.

Perspectives

According to the current metal levels, RP-BWTP sludge might be used for agriculture purposes. However, for an environmentally safe use of sewage sludge, further studies including systematic monitoring are recommended. Annual metal concentrations and predicted variations of those elements in the sludge should be monitored.

     

Chemical fractionation and heavy metal accumulation in the plant of Sesamum indicum (L.) var. T55 grown on soil amended with tannery sludge: Selection of single extractants

A pot experiment was carried out to study the single and sequential extractions of metals in different tannery sludge amendment and the potential of the plant of Sesamum indicum L. var. T55 (sesame) for the removal of metals from tannery waste contaminated site. The metal extraction efficiency obtained with each extractants was slightly different and follow the order; EDTA>DTPA>NH(4)NO(3)>NaNO(3)>CaCl(2). The correlation analysis between extractable metals in the different amendments of sludge and metal accumulation in the plant (lower and upper parts) showed better correlation for most of the tested metals with EDTA extraction. In this study, a sequential extraction technique was applied on different amendments of tannery sludge. The results showed that Mn, Zn, Cr and Cd were mostly associated with Fe-Mn oxide fraction in most of the amendments, K and Ni was found in residual (RES) fraction, Fe and Cu was bound with organic matter (OM) and RES fractions and Na was associated with carbonate (CAR) fraction. The metal accumulation after 60 d of growth of the plant was found in the order of K>Na>Fe>Zn>Cr>Mn>Cu>Pb>Ni>Cd and its translocation was found less in upper part. The accumulation of toxic metals (Cr, Ni and Cd) in the plants was found to increase with increase in sludge ratio, in contrast, the accumulation of Pb decreased. In view of growth parameters and metal accumulation in the plant, it was observed that lower amendments (25%) of tannery sludge were found suitable for the phytoremediation of most of the studied metals.     

Effect of operational parameters on heavy metal removal by electrocoagulation

In the present paper, the performance of electrocoagulation (EC) for the treatability of mixed metals (chromium (Cr), copper (Cu), lead (Pb), nickel (Ni), and zinc (Zn)) from metal plating industrial wastewater (EPW) has been investigated. The study mainly focused on the affecting parameters of EC process, such as electrode material, initial pH, distance between electrodes, electrode size, and applied voltage. The pH 8 is observed to be the best for metal removal. Fe–Fe electrode pair with 1-cm inter-electrode distance and electrode surface area of 40 cm² at an applied voltage of 8 V is observed to more efficient in the metal removal. Experiments have shown that the maximum removal percentage of the metals like Cr, Ni, Zn, Cu, and Pb are reported to be 96.2, 96.4, 99.9, 98, and 99.5 %, respectively, at a reaction time of 30 min. Under optimum conditions, the energy consumption is observed to be 51.40 kWh/m³. The method is observed to be very effective in the removal of metals from electroplating effluent.     

Occurrence and fate of heavy metals in the wastewater treatment process

The occurrence and the fate of heavy metals (Cd, Pb, Mn, Cu, Zn, Fe and Ni) during the wastewater treatment process were investigated in the wastewater treatment plant (WTP) of the city of Thessaloniki, northern Greece, operating in the activated sludge mode. For this purpose, wastewater and sludge samples were collected from six different points of the plant, namely, the influent (raw wastewater, RW), the effluent of the primary sedimentation tank (primary sedimentation effluent, PSE), the effluent of the secondary sedimentation tank (secondary sedimentation effluent, SSE), sludge from the primary sedimentation tank (primary sludge, PS), activated sludge from the recirculation stream (activated sludge, AS), and the digested/dewatered sludge (final sludge, FS).

The distribution of metals between the aqueous and the solid phase of wastewater was investigated. Good exponential correlation was found between the metal partition coefficient, logK_p, and the suspended solids concentration. The mass balance of heavy metals in the primary, secondary and the whole treatment process showed good closures for all metal species. The relative distribution of individual heavy metals in the treated effluent and the sludge streams indicated that Mn and Cu are primarily (>70%) accumulated in the sludge, while 47–63% of Cd, Cr, Pb, Fe, Ni and Zn remain in the treated effluent.     

Concentrations,spatial distribution,and pollution assessment of heavy metals in surficial sediments from upstream of Yellow River,China

Surface sediments were collected from 122 sites in the upstream of the Yellow River, China. The concentration of Fe, Mn, Cu, Ni, Zn, Cr, Pb, and Cd in sediments was investigated to explore the spatial distribution based on statistics and interpolation method. The results suggested that the concentrations of heavy metals were lower than potential effect levels (PEL). The samples above threshold effect level (TEL) for Pb and Zn were less than 10%, while almost 50% of samples for Ni exceeded PEL. Pb and Zn in sediments performed little or no adverse effects on the aquatic ecosystems. Higher concentrations of all heavy metals occurred in Qinghai and Gansu sections; the concentrations of Cu, Ni, and Zn were significantly higher than the Inner Mongolia section. Lower concentration of Fe, Mn, Cu, Ni, and Zn appeared in Qinghai section; the concentrations of Fe, Mn, Cr, and Pb manifested relatively steady and similar distributions and approximately decreasing tendency along the upstream of Yellow River.

     

Solid speciation and mobility of potentially toxic elements from natural and contaminated soils: a combined approach

The study area (Szklary Massif, SW Poland) comprises three sites of different soil provenance: (1) natural serpentine Cambisol, (2) anthroposol situated on waste dump and (3) cultivated Inceptisol developed on glacial tills next to the dump. Potentially toxic elements (PTE) have either lithogenic or anthropogenic origins in these sites. The chemical partitioning of Co, Cr, Cu, Ni, Pb and Zn among solid forms was determined by sequential extractions coupled with direct mineral identifications (SEM, electron microprobe analysis - EMPA, and XRD). Examination of solid residues after several extraction steps was conducted in order to discuss the indirect speciation obtained by the extraction method. Total concentrations of PTE having anthropogenic origin greatly exceed those of lithogenic origin. Mobility of studied PTE is variable in the different environments except for Cr which is always mostly found in residual fractions of extractions. Cu and Pb are more mobile than Cr and Co in all soils. Zn is more stable (Cu>Pb>Ni>Co>Zn>Cr) in the serpentine soil and cultivated epipedon (Pb>Cu>Zn>Ni>Co>Cr) than in the anthroposol (Zn>CuPb>Ni>Co>Cr). PTE of lithogenic origin are generally less mobile than those from anthropogenic origin except Ni which is more mobile in the serpentine soil. Nonetheless, mineral forms of metals better determine their mobility than metal origin. Identification by direct methods of the PTE mineral form was not possible for metals present at low concentrations (Cu, Pb). However, direct mineralogical examinations of the solid residues of several extractions steps improved the assessment of the PTE solid speciation and mobility, particularly for Cr, Ni and Zn.     

Trace metal speciation and fluxes within a major French wastewater treatment plant: impact of the successive treatments stages

Seven metals (Cd, Co, Cr, Cu, Fe, Ni and Pb) were monitored at the Seine-Aval wastewater treatment plant during 6 sampling campaigns in April 2004. Particulate and dissolved metals have been measured in 24 h composite samples at each treatment stage (primary settling, secondary activated sludge and tertiary flocculation by FeCl₃). In addition, the diffusive gradient in thin film technique (DGT) was used to determine the dissolved inert and labile metal fraction. Although all treatment stages were able to decrease particulate metals concentrations in wastewater, most dissolved metals concentrations were mainly affected during primary settling. This unexpected result was attributed to tertiary sludge filtrate recirculation. Metals added via the FeCl₃ reagent at the tertiary treatment were shown to lower the overall Cr removal from wastewater and to enrich Ni in effluents. The plant operating conditions (recirculation and reagent addition) appear therefore as important as treatment processes for the metals removal. Total metal fluxes were highly decreased by the whole treatment plant for Cd, Cr, Cu and Pb and to a lesser extend for Co and Ni. However, the labile metal fluxes were poorly decreased for Cu (18%), not significantly decreased for Ni and increased for Fe. The labile fraction of Cd, Co and Cr was not detectable at any stage of the plant. Discharged labile fluxes, at least for Ni, were potentially significant compared to the labile metal fluxes in the river measured downstream the plant. Treated urban wastewater discharges should be carefully considered as a possible source of bioavailable trace metals.     

Use of sequential extraction to assess metal partitioning in soils

The state of heavy metal pollution and the mobility of Cd, Cu, Ni, Cr, Pb and Zn were studied in three texturally different agricultural soil profiles near a Cu-Ni smelter in Harjavalta, Finland. The pseudo-total concentrations were determined by an aqua regia procedure. Metals were also determined after division into four fractions by sequential extraction with (1) acetic acid (exchangeable and specifically adsorbed metals), (2) a reducing agent (bound to Fe/Mn hydroxides), (3) an oxidizing agent (bound to soil organic matter) and (4) aqua regia (bound to mineral structures). Fallout from the smelter has increased the concentrations of Cd, Cu and Ni in the topsoil, where 75-90% of Cd, 49-72% of Cu and 22-52% of Ni occurred in the first two fractions. Slight Pb and Zn pollution was evident as well. High proportions of mobile Cd, Cu and Ni also deeper in the sandy soil, closest to the smelter, indicated some downward movement of metals. The hydroxide-bound fraction of Pb dominated in almost all soils and horizons, while Ni, Cr and Zn mostly occurred in mineral structures. Aqua regia extraction is usefully supplemented with sequential extraction, particularly in less polluted soils and in soils that exhibit substantial textural differences within the profiles.     

Relationship between heavy metals concentrations in egret species,their environment and food chain differences from two Headworks of Pakistan

Concentration of ten metals (Cd, Cr, Co, Cu, Fe, Li, Mn, Ni, Pb and Zn) were analyzed in the egg contents, prey and soil samples of little egret (Egretta garzetta) and cattle egret (Bubulcus ibis) from two Headworks to determine habitat and species-specific differences; to assess the importance of prey and habitat contamination as an exposure source for heavy metals. Concentration of Cu, Mn, Cr and Pb in egg contents, Fe, Co, Cu, Mn, Zn in prey and Fe, Co, Cu, Ni, Li in surface soils were significantly different (P < 0.05). Mean metal concentrations of Cr, Pb and Cd were relatively higher in little egret whereas Cu and Mn were higher in the egg contents of cattle egret. The mean concentrations of Cu, Mn and Zn were higher in prey samples of cattle egrets and Cr, Cd and Pb in prey samples of little egrets. In soil samples collected from little egret heronries metal concentrations were higher except Cu and Ni. Correlation Analysis and Hierarchical Agglomerative Cluster Analysis (HACA) identified relatively similar associations of metals and their source identification. Metals such as Fe, Cu, Mn, and Li were related with geochemical origin from parent rock material as well as anthropogenic input whereas Cr, Cd, Pb, Ni, Co and Zn were associated mostly with anthropogenic activities. The study suggested that eggs are useful bio-monitor of local heavy metal contamination.     

Assessment of heavy metal contamination in Hindon River sediments: a chemometric and geochemical approach

The aim of this study was to assess the level of heavy metals (Cd, Cr, Cu, Fe, Mn, Ni, Pb, and Zn) in the surface sediments of the Hindon River, India that receives both treated and untreated municipal and industrial discharges generated in and around Ghaziabad, India. Mean metals concentrations (mg kg⁻¹) were in the range of; Cu: 21.70-280.33, Cd: 0.29-6.29, Fe: 4151.75-17318.75, Zn: 22.22.50-288.29, Ni: 13.90-57.66, Mn: 49.55-516.97, Cr: 17.48-33.70 and Pb: 27.56-313.57 respectively. Chemometric analysis was applied to identify contribution sources by heavy metals while geochemical approaches (enrichment factor and geo-accumulation index) were exploited for the assessment of the enrichment and contamination level of heavy metals in the river sediments. Chemometric analysis suggested anthropic origin of Cu, Cd, Pb, Zn, and Ni while Fe showed lithogenic origin. Mn and Cr was associated and controlled by mixed origin. Geochemical approach confirms the anthropogenic influence of heavy metal pollution in the river sediments. The study suggests that a complementary approach that integrates chemometric analysis, sediment quality criteria, and geochemical investigation should be considered in order to provide a more accurate appraisal of the heavy metal pollution in river sediments. Consequently, it may serve to undertake and design effective strategies and remedial measures to prevent further deterioration of the river ecosystem in future.     

A comparative study on metal sorption by brown seaweed

This study compared the sorption of Ag, Cd, Co, Cd, Mn, Ni, Pb and Zn by a Ca-treated Sargassum biomass at pH 5.0, under low and high ionic strength (IS) conditions. The sorption isotherms of As [As(V)] and Cr [Cr(III) and Cr(VI)] were also determined at low IS. The isotherm data for the eight cationic metals and Cr(III) were well fitted by Langmuir equations. Generally, the maximum metal uptake (Umax) followed: Cr(III) > Pb approximately Cu > Ag approximately Zn approximately Cd > Ni approximately Mn approximately Co > Cr(VI) > As(V) at low IS and Pb > Cu > Co > Mn approximately Cd > Zn approximately Ag > Ni at high IS. As(V) did not bind to the seaweed at pH 5.0. The results indicated that sorption of Pb was not affected by the increasing IS, though the percentage of free Pb ions in the water was greatly reduced as predicted by the speciation model. High IS lowered Umax by 10-36% (except Co and Pb), and lowered the affinity constant of the metal by 33-91% for all cationic metals, as compared to low IS. Moreover, the removal efficiency of the cationic metals and Cr decreased exponentially with initial metal concentrations and was lower at high IS. Ion-exchange was the mechanism responsible for the cationic metal sorption onto the seaweed, and Na ion interfered with the cationic metal binding through electrostatic interaction. In conclusion, this study showed the differential binding capacity of the Sargassm biomass for different metals and oxidation states and the differential effects of IS. According to the present results, Sargassum may be considered a good biosorbent for cationic metals (especially Pb) in both low and high-salt containing wastewater.     

Bioleaching of heavy metals from anaerobically digested sewage sludge using FeS2 as an energy source

The effect of using FeS2 as an energy source, on the bioleaching of heavy metals (Zn, Cr, Cu, Pb and Ni) and nutrients (nitrogen and phosphorus) from anaerobically digested sludge using isolated indigenous iron-oxidizing bacteria was investigated in this paper. Addition of FeS2 in the range of 0.5-4.0 g l(-1) accelerated the acidification of sludge and raised the oxidation-reduction potential of sludge medium with an inoculation of 15% (v/v) of active bacteria, thus resulting in an overall increase in metal dissolution efficiency. After 16 days of bioleaching at 28 degrees C and an initial pH of 3.0, up to 99% of Zn, 65% of Cr, 74% of Cu, 58% of Pb and 84% of Ni can be removed from the sludge. In contrast, only 94% of Zn, 12% of Cr, 21% of Cu, 32% of Pb and 38% of Ni were leached out in the control without inoculation of iron-oxidizing bacteria and the addition of FeS2. Less than 15% of nitrogen and 6% of phosphorous were lost after 16 days of bioleaching when using FeS2 as the energy source. Comparing to 39% and 45% loss respectively for these two nutrients when using FeSO4.7H2O as the energy source, FeS2 appears to be a more suitable energy source for preserving nutrients in sludge while removing heavy metals from sludge.     

An ultrasonic assisted extraction method to release heavy metals from untreated sewage sludge samples

A rapid ultrasound accelerated sequential extraction procedure has been used to develop sequential extraction proposed by BCR protocol (the community Bureau of Reference now the European Union "Measurement and Testing Programme"). The effects of the ultrasonic treatment on the extraction of Cu, Cd, Cr, Pb, Ni and Zn from untreated sewage sludge collected from industrial site of Hyderabad city (Pakistan) were compared with those obtained from conventional sequentional extraction procedure of modified BCR protocol. In BCR method, each extraction steps takes 10h, where as with the use of compromise sonication conditions in ultrasonic bath, steps 1-3 of the sequential extraction (excluding the hydrogen peroxide digestion in step 3, which was not performed with sonication) could be completed in 30, 30 and 30 min, respectively. Extractable Cd, Cr, Pb and Ni contents were obtained by both comparable methodologies were measured by electrothermal atomic absorption spectrometry (ETAAS), while for Cu and Zn Flame atomic absorption spectrometry (FAAS) was used. The validations of both methods were compared by the analysis of certified reference material of soil amended with sewage sludge (BCR 483). According to statistical evaluation of the results, the proposed accelerated extraction method is valid alternative to conventional shaking with much shorter extraction time with p value <0.05. The overall metal recoveries in steps 1-3 (excluding residual step) were 95-100% of those obtained with the conventional BCR protocol, except for Cu extracted (91.6%) as related to indicative values of Cu in BCR 483 obtained in 1-3 steps. The results of the partitioning study of untreated industrial waste water sewage sludge, indicate that more easily mobilized forms (acid exchangeable) were predominant for Cd and Zn, in contrast, the largest amount of Pb and Cr was associated with the iron/manganese oxide and organic matter/sulphide fractions.     

Selected trace metals in oysters (Crassostrea iridescens) and sediments from the discharge zone of the submarine sewage outfall in Mazatlán Bay (southeast Gulf of California): chemical fractions and bioaccumulation factors

Concentrations of Cd, Cr, Cu, Fe, Mn, Ni, Pb and Zn in the soft tissue of Crassostrea iridescens and the associated surface sediments (bulk and bioavailable metal concentrations) from an area influenced by a sewage outfall in Mazatlán Bay (southeast Gulf of California), were determined by atomic absorption spectrophotometry. Significant spatial differences in metal concentrations in both the bulk and bioavailable forms in the sediments were identified. An enrichment of Cu, Ni, Pb and Zn in sites located on a south-north transect was detected indicating a dominant influence of the sewage outfall toward the north. C. iridescens accumulated more Zn, Cu, Ni, Fe, Cd; and less Mn, Cr and Pb than were bioavailable in the sediments, as measured using conventional extraction analysis. The degree of enrichment and the bioavailable metal concentrations in the sediments of the south portion of Mazatlán Bay is discussed. The potential ability of C. iridescens as a biomonitor of metallic pollutants is postulated.